Пытаюсь подключить LG G1800, не для GPRS, а в качестве флэш-накопителя, в винде определяется, как USB Mass storage... в Дебиане вытащил из логов загрузки ( dmesg ) следующие ключевые моменты:
Код: Выделить всё
usb 1-2: new low speed USB device using uhci_hcd and address 2
...
usb 1-2: device not accepting address 2, error -71
...
usb 1-2: new low speed USB device using uhci_hcd and address 4
ide0 at 0x1f0-0x1f7,0x3f6 on irq 14
...
usb 1-2: configuration #1 chosen from 1 choice
usb 2-2: new full speed USB device using uhci_hcd and address 2
...
Initializing USB Mass Storage driver...
...
scsi2 : SCSI emulation for USB Mass Storage devices
usb-storage: device found at 2
usb-storage: waiting for device to settle before scanning
usbcore: registered new driver usb-storage
USB Mass Storage support registered.
.....
usb 2-2: reset full speed USB device using uhci_hcd and address 2
usb 2-2: device not accepting address 2, error -22
usb 2-2: USB disconnect, address 2
sd 2:0:0:0: SCSI error: return code = 0x00070000
end_request: I/O error, dev sdb, sector 124543
Buffer I/O error on device sdb1, logical block 62240
sd 2:0:0:0: SCSI error: return code = 0x00070000
end_request: I/O error, dev sdb, sector 124543
Buffer I/O error on device sdb1, logical block 62240
Buffer I/O error on device sdb1, logical block 62240
Buffer I/O error on device sdb1, logical block 62240
Buffer I/O error on device sdb1, logical block 62240
Buffer I/O error on device sdb1, logical block 62240
Buffer I/O error on device sdb1, logical block 62208
Buffer I/O error on device sdb1, logical block 62209
Buffer I/O error on device sdb1, logical block 62210
Buffer I/O error on device sdb1, logical block 62211
scsi 2:0:0:0: rejecting I/O to dead device
scsi 2:0:0:0: rejecting I/O to dead device
scsi 2:0:0:0: rejecting I/O to dead device
sdb : READ CAPACITY failed.
sdb : status=0, message=00, host=1, driver=00
sdb : sense not available.
scsi 2:0:0:0: rejecting I/O to dead device
sdb: Write Protect is off
sdb: Mode Sense: 00 00 00 00
sdb: assuming drive cache: write through
scsi 2:0:0:0: rejecting I/O to dead device
scsi 2:0:0:0: rejecting I/O to dead device
scsi 2:0:0:0: rejecting I/O to dead device
scsi 2:0:0:0: rejecting I/O to dead device
scsi 2:0:0:0: rejecting I/O to dead device
scsi 2:0:0:0: rejecting I/O to dead device
scsi 2:0:0:0: rejecting I/O to dead device
scsi 2:0:0:0: rejecting I/O to dead device
scsi 2:0:0:0: rejecting I/O to dead device
scsi 2:0:0:0: rejecting I/O to dead deviceв openSuSE 10.2, SuSE 10.1 тоже не работало, поэтому пишу именно в этот раздел, что делать-то ?
P.S. USB 2-2 - это вроде мыша ) в юсб порт воткнутая