Возникла странная проблема. Есть боевой сервер на Debian Lenny(без Х). В нем стоят 2 SATA винта 500Gb объединенные в raid1. Собственно каждый разбит так:
1. Мелкий раздел в 150Мб под /boot.
2. Все остальное под lvm, тома которого уже разделены на нужные разделы.
Более подробно вот -
Код: Выделить всё
alex@deb-gate2:~$ sudo fdisk -l
Disk /dev/sda: 500.1 GB, 500106780160 bytes
255 heads, 63 sectors/track, 60801 cylinders
Units = cylinders of 16065 * 512 = 8225280 bytes
Disk identifier: 0x000d049c
Device Boot Start End Blocks Id System
/dev/sda1 * 1 18 144553+ fd Linux raid autodetect
/dev/sda2 19 60801 488239447+ fd Linux raid autodetect
Disk /dev/sdb: 500.1 GB, 500106780160 bytes
255 heads, 63 sectors/track, 60801 cylinders
Units = cylinders of 16065 * 512 = 8225280 bytes
Disk identifier: 0xcf2d61b7
Device Boot Start End Blocks Id System
/dev/sdb1 * 1 18 144553+ fd Linux raid autodetect
/dev/sdb2 19 60801 488239447+ fd Linux raid autodetect
Disk /dev/md0: 147 MB, 147914752 bytes
2 heads, 4 sectors/track, 36112 cylinders
Units = cylinders of 8 * 512 = 4096 bytes
Disk identifier: 0x00000000
Disk /dev/md0 doesn't contain a valid partition table
Disk /dev/md1: 499.9 GB, 499957104640 bytes
2 heads, 4 sectors/track, 122059840 cylinders
Units = cylinders of 8 * 512 = 4096 bytes
Disk identifier: 0x00000000
Disk /dev/md1 doesn't contain a valid partition table
Disk /dev/dm-0: 34.9 GB, 34997272576 bytes
255 heads, 63 sectors/track, 4254 cylinders
Units = cylinders of 16065 * 512 = 8225280 bytes
Disk identifier: 0x00000000
Disk /dev/dm-0 doesn't contain a valid partition table
Disk /dev/dm-1: 1497 MB, 1497366528 bytes
255 heads, 63 sectors/track, 182 cylinders
Units = cylinders of 16065 * 512 = 8225280 bytes
Disk identifier: 0x00000000
Disk /dev/dm-1 doesn't contain a valid partition table
Disk /dev/dm-2: 463.4 GB, 463462203392 bytes
255 heads, 63 sectors/track, 56346 cylinders
Units = cylinders of 16065 * 512 = 8225280 bytes
Disk identifier: 0x00000000
Disk /dev/dm-2 doesn't contain a valid partition tableИнфа о рэйде:
Код: Выделить всё
alex@deb-gate2:~$ sudo mdadm -D /dev/md0
/dev/md0:
Version : 00.90
Creation Time : Tue Mar 23 17:31:22 2010
Raid Level : raid1
Array Size : 144448 (141.09 MiB 147.91 MB)
Used Dev Size : 144448 (141.09 MiB 147.91 MB)
Raid Devices : 2
Total Devices : 2
Preferred Minor : 0
Persistence : Superblock is persistent
Update Time : Fri Apr 9 16:32:12 2010
State : clean
Active Devices : 2
Working Devices : 2
Failed Devices : 0
Spare Devices : 0
UUID : 959c090d:757e2923:8afd3c9d:727a8f80
Events : 0.182
Number Major Minor RaidDevice State
0 8 1 0 active sync /dev/sda1
1 8 17 1 active sync /dev/sdb1
alex@deb-gate2:~$ sudo mdadm -D /dev/md1
/dev/md1:
Version : 00.90
Creation Time : Tue Mar 23 17:31:31 2010
Raid Level : raid1
Array Size : 488239360 (465.62 GiB 499.96 GB)
Used Dev Size : 488239360 (465.62 GiB 499.96 GB)
Raid Devices : 2
Total Devices : 1
Preferred Minor : 1
Persistence : Superblock is persistent
Update Time : Fri Apr 9 16:40:35 2010
State : clean, degraded
Active Devices : 1
Working Devices : 1
Failed Devices : 0
Spare Devices : 0
UUID : fbe67b85:2b9c2c46:8616ffc0:54b13a00
Events : 0.159152
Number Major Minor RaidDevice State
0 8 2 0 active sync /dev/sda2
1 0 0 1 removedНедавно mdadm выдал - диск sdb умер(fail). Ладно думаю, упал так упал - заменю(благо такой же диск был). Удалил его из рэйда
Код: Выделить всё
mdadm /dev/md1 --remove /dev/sdb2
mdadm /dev/md0 --remove /dev/sdb1вытащил и вставил новый(на материнке 6 слотов для SATA я вставил не в тот что был и заодно другим кабелем). Скопировал на новый таблицу разделов
Код: Выделить всё
sudo sfdisk -d /dev/sda > ./sda.out
sudo sfdisk /dev/sdb < ./sda.outа потом добавил его в рейд:
Код: Выделить всё
sudo mdadm /dev/md0 --add /dev/sdb1
sudo mdadm /dev/md1 --add /dev/sdb2После этого пошла синхронизация. Мелкий раздел (md0) синхронизировался сразу, а большой застрял на 30%. В /var/log/messages посыпались такие вот сообщения:
Код: Выделить всё
Apr 7 12:56:18 deb-gate2 kernel: [ 1551.646121] md: bind<sdb1>
Apr 7 12:56:18 deb-gate2 kernel: [ 1551.705387] RAID1 conf printout:
Apr 7 12:56:18 deb-gate2 kernel: [ 1551.705387] --- wd:1 rd:2
Apr 7 12:56:18 deb-gate2 kernel: [ 1551.705387] disk 0, wo:0, o:1, dev:sda1
Apr 7 12:56:18 deb-gate2 kernel: [ 1551.705387] disk 1, wo:1, o:1, dev:sdb1
Apr 7 12:56:18 deb-gate2 kernel: [ 1551.712172] md: recovery of RAID array md0
Apr 7 12:56:18 deb-gate2 kernel: [ 1551.712172] md: minimum _guaranteed_ speed: 1000 KB/sec/disk.
Apr 7 12:56:18 deb-gate2 kernel: [ 1551.712172] md: using maximum available idle IO bandwidth (but not more than 200000 KB/sec) for recovery.
Apr 7 12:56:18 deb-gate2 kernel: [ 1551.712172] md: using 128k window, over a total of 144448 blocks.
Apr 7 12:56:21 deb-gate2 kernel: [ 1555.077116] md: md0: recovery done.
Apr 7 12:56:21 deb-gate2 kernel: [ 1555.131634] RAID1 conf printout:
Apr 7 12:56:21 deb-gate2 kernel: [ 1555.131634] --- wd:2 rd:2
Apr 7 12:56:21 deb-gate2 kernel: [ 1555.131634] disk 0, wo:0, o:1, dev:sda1
Apr 7 12:56:21 deb-gate2 kernel: [ 1555.131634] disk 1, wo:0, o:1, dev:sdb1
Apr 7 12:56:24 deb-gate2 kernel: [ 1558.484407] md: bind<sdb2>
Apr 7 12:56:24 deb-gate2 kernel: [ 1558.517038] RAID1 conf printout:
Apr 7 12:56:24 deb-gate2 kernel: [ 1558.517038] --- wd:1 rd:2
Apr 7 12:56:24 deb-gate2 kernel: [ 1558.517038] disk 0, wo:0, o:1, dev:sda2
Apr 7 12:56:24 deb-gate2 kernel: [ 1558.517038] disk 1, wo:1, o:1, dev:sdb2
Apr 7 12:56:24 deb-gate2 kernel: [ 1558.517038] md: recovery of RAID array md1
Apr 7 12:56:24 deb-gate2 kernel: [ 1558.517038] md: minimum _guaranteed_ speed: 1000 KB/sec/disk.
Apr 7 12:56:24 deb-gate2 kernel: [ 1558.517038] md: using maximum available idle IO bandwidth (but not more than 200000 KB/sec) for recovery.
Apr 7 12:56:24 deb-gate2 kernel: [ 1558.517038] md: using 128k window, over a total of 488239360 blocks.
Apr 7 13:31:01 deb-gate2 kernel: [ 3642.947432] res 40/00:00:00:00:00/00:00:00:00:00/00 Emask 0x4 (timeout)
Apr 7 13:31:01 deb-gate2 kernel: [ 3642.947509] ata1: soft resetting link
Apr 7 13:31:01 deb-gate2 kernel: [ 3643.137924] ata1.00: configured for UDMA/133
Apr 7 13:31:01 deb-gate2 kernel: [ 3643.153885] ata1.01: configured for UDMA/133
Apr 7 13:31:01 deb-gate2 kernel: [ 3643.153896] ata1: EH complete
Apr 7 13:31:01 deb-gate2 kernel: [ 3643.179349] sd 0:0:0:0: [sda] 976771055 512-byte hardware sectors (500107 MB)
Apr 7 13:31:01 deb-gate2 kernel: [ 3643.223349] sd 0:0:0:0: [sda] Write Protect is off
Apr 7 13:31:01 deb-gate2 kernel: [ 3643.255094] sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
Apr 7 13:31:01 deb-gate2 kernel: [ 3643.272084] sd 0:0:1:0: [sdb] 976771055 512-byte hardware sectors (500107 MB)
Apr 7 13:31:01 deb-gate2 kernel: [ 3643.274685] sd 0:0:1:0: [sdb] Write Protect is off
Apr 7 13:31:01 deb-gate2 kernel: [ 3643.297964] sd 0:0:1:0: [sdb] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
Apr 7 13:31:01 deb-gate2 kernel: [ 3643.330083] sd 0:0:0:0: [sda] 976771055 512-byte hardware sectors (500107 MB)
Apr 7 13:31:01 deb-gate2 kernel: [ 3643.386489] sd 0:0:0:0: [sda] Write Protect is off
Apr 7 13:31:01 deb-gate2 kernel: [ 3643.452340] sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
Apr 7 13:31:01 deb-gate2 kernel: [ 3643.457178] sd 0:0:1:0: [sdb] 976771055 512-byte hardware sectors (500107 MB)
Apr 7 13:31:01 deb-gate2 kernel: [ 3643.457996] sd 0:0:1:0: [sdb] Write Protect is off
Apr 7 13:31:01 deb-gate2 kernel: [ 3643.462028] sd 0:0:1:0: [sdb] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
Apr 7 13:31:59 deb-gate2 kernel: [ 3700.638812] res 40/00:00:00:00:00/00:00:00:00:00/00 Emask 0x4 (timeout)
Apr 7 13:31:59 deb-gate2 kernel: [ 3700.638888] ata1: soft resetting link
Apr 7 13:31:59 deb-gate2 kernel: [ 3700.834059] ata1.00: configured for UDMA/133
Apr 7 13:31:59 deb-gate2 kernel: [ 3700.850042] ata1.01: configured for UDMA/133
Apr 7 13:31:59 deb-gate2 kernel: [ 3700.850053] ata1: EH complete
Apr 7 13:31:59 deb-gate2 kernel: [ 3700.877468] sd 0:0:0:0: [sda] 976771055 512-byte hardware sectors (500107 MB)
Apr 7 13:31:59 deb-gate2 kernel: [ 3700.917470] sd 0:0:0:0: [sda] Write Protect is off
Apr 7 13:31:59 deb-gate2 kernel: [ 3700.949468] sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
Apr 7 13:31:59 deb-gate2 kernel: [ 3700.969468] sd 0:0:1:0: [sdb] 976771055 512-byte hardware sectors (500107 MB)
Apr 7 13:31:59 deb-gate2 kernel: [ 3700.973469] sd 0:0:1:0: [sdb] Write Protect is off
Apr 7 13:31:59 deb-gate2 kernel: [ 3700.993469] sd 0:0:1:0: [sdb] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
Apr 7 13:31:59 deb-gate2 kernel: [ 3701.025469] sd 0:0:0:0: [sda] 976771055 512-byte hardware sectors (500107 MB)
Apr 7 13:31:59 deb-gate2 kernel: [ 3701.105468] sd 0:0:0:0: [sda] Write Protect is off
Apr 7 13:31:59 deb-gate2 kernel: [ 3701.160576] sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
Apr 7 13:31:59 deb-gate2 kernel: [ 3701.162060] sd 0:0:1:0: [sdb] 976771055 512-byte hardware sectors (500107 MB)
Apr 7 13:31:59 deb-gate2 kernel: [ 3701.162470] sd 0:0:1:0: [sdb] Write Protect is off
Apr 7 13:31:59 deb-gate2 kernel: [ 3701.163406] sd 0:0:1:0: [sdb] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
Apr 7 13:33:20 deb-gate2 kernel: [ 3783.046567] res 40/00:00:00:00:00/00:00:00:00:00/00 Emask 0x4 (timeout)
Apr 7 13:33:20 deb-gate2 kernel: [ 3783.046643] ata1: soft resetting link
Apr 7 13:33:20 deb-gate2 kernel: [ 3783.235068] ata1.00: configured for UDMA/133
Apr 7 13:33:20 deb-gate2 kernel: [ 3783.251065] ata1.01: configured for UDMA/133
Apr 7 13:33:20 deb-gate2 kernel: [ 3783.251077] ata1: EH complete
Apr 7 13:33:20 deb-gate2 kernel: [ 3783.277188] sd 0:0:0:0: [sda] 976771055 512-byte hardware sectors (500107 MB)
Apr 7 13:33:21 deb-gate2 kernel: [ 3783.336719] sd 0:0:0:0: [sda] Write Protect is off
Apr 7 13:33:21 deb-gate2 kernel: [ 3783.370486] sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
Apr 7 13:33:21 deb-gate2 kernel: [ 3783.391132] sd 0:0:1:0: [sdb] 976771055 512-byte hardware sectors (500107 MB)
Apr 7 13:33:21 deb-gate2 kernel: [ 3783.398421] sd 0:0:1:0: [sdb] Write Protect is off
Apr 7 13:33:21 deb-gate2 kernel: [ 3783.420504] sd 0:0:1:0: [sdb] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
Apr 7 13:33:21 deb-gate2 kernel: [ 3783.454421] sd 0:0:0:0: [sda] 976771055 512-byte hardware sectors (500107 MB)
Apr 7 13:33:21 deb-gate2 kernel: [ 3783.548685] sd 0:0:0:0: [sda] Write Protect is off
Apr 7 13:33:21 deb-gate2 kernel: [ 3783.580648] sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
Apr 7 13:33:21 deb-gate2 kernel: [ 3783.583646] sd 0:0:1:0: [sdb] 976771055 512-byte hardware sectors (500107 MB)
Apr 7 13:33:21 deb-gate2 kernel: [ 3783.585599] sd 0:0:1:0: [sdb] Write Protect is off
Apr 7 13:33:21 deb-gate2 kernel: [ 3783.589567] sd 0:0:1:0: [sdb] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
Apr 7 13:33:57 deb-gate2 kernel: [ 3819.726770] ata1.01: limiting speed to UDMA/100:PIO4
Apr 7 13:33:57 deb-gate2 kernel: [ 3819.726822] res 40/00:00:00:00:00/00:00:00:00:00/00 Emask 0x4 (timeout)
Apr 7 13:33:57 deb-gate2 kernel: [ 3819.726899] ata1: soft resetting link
Apr 7 13:33:57 deb-gate2 kernel: [ 3819.915337] ata1.00: configured for UDMA/133
Apr 7 13:33:57 deb-gate2 kernel: [ 3819.931323] ata1.01: configured for UDMA/100
Apr 7 13:33:57 deb-gate2 kernel: [ 3819.931335] ata1: EH complete
Apr 7 13:33:57 deb-gate2 kernel: [ 3819.953715] sd 0:0:0:0: [sda] 976771055 512-byte hardware sectors (500107 MB)
Apr 7 13:33:57 deb-gate2 kernel: [ 3820.027533] sd 0:0:0:0: [sda] Write Protect is off
Apr 7 13:33:57 deb-gate2 kernel: [ 3820.057254] sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
Apr 7 13:33:57 deb-gate2 kernel: [ 3820.072435] sd 0:0:1:0: [sdb] 976771055 512-byte hardware sectors (500107 MB)
Apr 7 13:33:57 deb-gate2 kernel: [ 3820.078988] sd 0:0:1:0: [sdb] Write Protect is off
Apr 7 13:33:57 deb-gate2 kernel: [ 3820.102081] sd 0:0:1:0: [sdb] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
Apr 7 13:33:57 deb-gate2 kernel: [ 3820.133247] sd 0:0:0:0: [sda] 976771055 512-byte hardware sectors (500107 MB)
Apr 7 13:33:57 deb-gate2 kernel: [ 3820.201302] sd 0:0:0:0: [sda] Write Protect is off
Apr 7 13:33:57 deb-gate2 kernel: [ 3820.226204] sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
Apr 7 13:33:57 deb-gate2 kernel: [ 3820.228345] sd 0:0:1:0: [sdb] 976771055 512-byte hardware sectors (500107 MB)
Apr 7 13:33:57 deb-gate2 kernel: [ 3820.230234] sd 0:0:1:0: [sdb] Write Protect is off
Apr 7 13:33:57 deb-gate2 kernel: [ 3820.231756] sd 0:0:1:0: [sdb] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
Apr 7 13:34:39 deb-gate2 kernel: [ 3862.403684] res 40/00:00:00:00:00/00:00:00:00:00/00 Emask 0x4 (timeout)
Apr 7 13:34:39 deb-gate2 kernel: [ 3862.403760] ata1: soft resetting link
Apr 7 13:34:40 deb-gate2 kernel: [ 3862.642562] ata1.00: configured for UDMA/133
Apr 7 13:34:40 deb-gate2 kernel: [ 3862.659178] ata1.01: configured for UDMA/100
Apr 7 13:34:40 deb-gate2 kernel: [ 3862.659190] ata1: EH complete
Apr 7 13:34:40 deb-gate2 kernel: [ 3862.682562] sd 0:0:0:0: [sda] 976771055 512-byte hardware sectors (500107 MB)
Apr 7 13:34:40 deb-gate2 kernel: [ 3862.742562] sd 0:0:0:0: [sda] Write Protect is off
Apr 7 13:34:40 deb-gate2 kernel: [ 3862.774562] sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
Apr 7 13:34:40 deb-gate2 kernel: [ 3862.798562] sd 0:0:1:0: [sdb] 976771055 512-byte hardware sectors (500107 MB)
Apr 7 13:34:40 deb-gate2 kernel: [ 3862.802563] sd 0:0:1:0: [sdb] Write Protect is off
Apr 7 13:34:40 deb-gate2 kernel: [ 3862.818562] sd 0:0:1:0: [sdb] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
Apr 7 13:34:40 deb-gate2 kernel: [ 3862.852578] sd 0:0:0:0: [sda] 976771055 512-byte hardware sectors (500107 MB)
Apr 7 13:34:40 deb-gate2 kernel: [ 3862.892578] sd 0:0:0:0: [sda] Write Protect is off
Apr 7 13:34:40 deb-gate2 kernel: [ 3862.924578] sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
Apr 7 13:34:40 deb-gate2 kernel: [ 3862.928578] sd 0:0:1:0: [sdb] 976771055 512-byte hardware sectors (500107 MB)
Apr 7 13:34:40 deb-gate2 kernel: [ 3862.928578] sd 0:0:1:0: [sdb] Write Protect is off
Apr 7 13:34:40 deb-gate2 kernel: [ 3862.932578] sd 0:0:1:0: [sdb] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
Apr 7 13:35:18 deb-gate2 kernel: [ 3900.748688] res 40/00:00:00:00:00/00:00:00:00:00/00 Emask 0x4 (timeout)
Apr 7 13:35:18 deb-gate2 kernel: [ 3900.748792] ata1: soft resetting linkСкорость синхронизации падала и падала и под конец mdadm решил что диск тоже битый -
Код: Выделить всё
A Fail event had been detected on md device /dev/md1.
It could be related to component device /dev/sdb2.
Faithfully yours, etc.
P.S. The /proc/mdstat file currently contains the following:
Personalities : [raid1]
md1 : active raid1 sdb2[2](F) sda2[0]
488239360 blocks [2/1] [U_]
md0 : active raid1 sdb1[1] sda1[0]
144448 blocks [2/2] [UU]
unused devices: <none>Но диск насколько я знаю нормальный, тем более, что раздел sdb1 вполне себе живет и здравствует. Я попробовал повторить процедуру установки диск рэйд и удаления диска из рэйда, но это ничего не дало. Только теперь синхронизация падала в районе первого процента.
Кто-нибудь может прояснить мне куда копать? Это глючит контроллер raid на материнке? Как сие проверить?
Температуру хардов проверял - держится в районе 38С. Чип на материнке выдает тоже что-то около 40С.
Более подробная инфа по железу:
Хард:
Код: Выделить всё
alex@deb-gate2:~$ sudo hdparm -i /dev/sdb
/dev/sdb:
Model=ST3500320AS , FwRev=SD04 , SerialNo= 9QM04QAG
Config={ HardSect NotMFM HdSw>15uSec Fixed DTR>10Mbs RotSpdTol>.5% }
RawCHS=16383/16/63, TrkSize=0, SectSize=0, ECCbytes=4
BuffType=unknown, BuffSize=0kB, MaxMultSect=16, MultSect=?16?
CurCHS=16383/16/63, CurSects=16514064, LBA=yes, LBAsects=976771055
IORDY=on/off, tPIO={min:120,w/IORDY:120}, tDMA={min:120,rec:120}
PIO modes: pio0 pio1 pio2 pio3 pio4
DMA modes: mdma0 mdma1 mdma2
UDMA modes: udma0 udma1 udma2 udma3 udma4 udma5 *udma6
AdvancedPM=no WriteCache=enabled
Drive conforms to: Unspecified: ATA/ATAPI-4,5,6,7
* signifies the current active mode
alex@deb-gate2:~$ sudo smartctl -a /dev/sdb
smartctl version 5.38 [i686-pc-linux-gnu] Copyright (C) 2002-8 Bruce Allen
Home page is http://smartmontools.sourceforge.net/
=== START OF INFORMATION SECTION ===
Model Family: Seagate Barracuda 7200.11
Device Model: ST3500320AS
Serial Number: 9QM04QAG
Firmware Version: SD04
User Capacity: 500 106 780 160 bytes
Device is: In smartctl database [for details use: -P show]
ATA Version is: 7
ATA Standard is: Exact ATA specification draft version not indicated
Local Time is: Fri Apr 9 16:48:41 2010 MSD
SMART support is: Available - device has SMART capability.
SMART support is: Enabled
=== START OF READ SMART DATA SECTION ===
SMART overall-health self-assessment test result: PASSED
General SMART Values:
Offline data collection status: (0x82) Offline data collection activity
was completed without error.
Auto Offline Data Collection: Enabled.
Self-test execution status: ( 25) The self-test routine was aborted by
the host.
Total time to complete Offline
data collection: ( 642) seconds.
Offline data collection
capabilities: (0x7b) SMART execute Offline immediate.
Auto Offline data collection on/off support.
Suspend Offline collection upon new
command.
Offline surface scan supported.
Self-test supported.
Conveyance Self-test supported.
Selective Self-test supported.
SMART capabilities: (0x0003) Saves SMART data before entering
power-saving mode.
Supports SMART auto save timer.
Error logging capability: (0x01) Error logging supported.
General Purpose Logging supported.
Short self-test routine
recommended polling time: ( 1) minutes.
Extended self-test routine
recommended polling time: ( 106) minutes.
Conveyance self-test routine
recommended polling time: ( 2) minutes.
SCT capabilities: (0x003b) SCT Status supported.
SCT Feature Control supported.
SCT Data Table supported.
SMART Attributes Data Structure revision number: 10
Vendor Specific SMART Attributes with Thresholds:
ID# ATTRIBUTE_NAME FLAG VALUE WORST THRESH TYPE UPDATED WHEN_FAILED RAW_VALUE
1 Raw_Read_Error_Rate 0x000f 117 099 006 Pre-fail Always - 150398667
3 Spin_Up_Time 0x0003 096 092 000 Pre-fail Always - 0
4 Start_Stop_Count 0x0032 100 100 020 Old_age Always - 702
5 Reallocated_Sector_Ct 0x0033 100 100 036 Pre-fail Always - 0
7 Seek_Error_Rate 0x000f 065 060 030 Pre-fail Always - 12896930277
9 Power_On_Hours 0x0032 099 099 000 Old_age Always - 1392
10 Spin_Retry_Count 0x0013 100 100 097 Pre-fail Always - 11
12 Power_Cycle_Count 0x0032 099 037 020 Old_age Always - 1060
184 Unknown_Attribute 0x0032 100 100 099 Old_age Always - 0
187 Reported_Uncorrect 0x0032 100 100 000 Old_age Always - 0
188 Unknown_Attribute 0x0032 100 100 000 Old_age Always - 0
189 High_Fly_Writes 0x003a 100 100 000 Old_age Always - 0
190 Airflow_Temperature_Cel 0x0022 063 050 045 Old_age Always - 37 (Lifetime Min/Max 37/38)
194 Temperature_Celsius 0x0022 037 050 000 Old_age Always - 37 (0 18 0 0)
195 Hardware_ECC_Recovered 0x001a 042 028 000 Old_age Always - 150398667
197 Current_Pending_Sector 0x0012 100 100 000 Old_age Always - 271
198 Offline_Uncorrectable 0x0010 100 100 000 Old_age Offline - 271
199 UDMA_CRC_Error_Count 0x003e 200 200 000 Old_age Always - 0
SMART Error Log Version: 1
No Errors Logged
SMART Self-test log structure revision number 1
No self-tests have been logged. [To run self-tests, use: smartctl -t]
SMART Selective self-test log data structure revision number 1
SPAN MIN_LBA MAX_LBA CURRENT_TEST_STATUS
1 0 0 Not_testing
2 0 0 Not_testing
3 0 0 Not_testing
4 0 0 Not_testing
5 0 0 Not_testing
Selective self-test flags (0x0):
After scanning selected spans, do NOT read-scan remainder of disk.
If Selective self-test is pending on power-up, resume after 0 minute delay.Ошибки смарта на втором харде примерно аналогичные.
Мать:
Код: Выделить всё
alex@deb-gate2:~$ sudo dmidecode --type 2
# dmidecode 2.9
SMBIOS 2.3 present.
Handle 0x0002, DMI type 2, 8 bytes
Base Board Information
Manufacturer: Gigabyte Technology Co., Ltd.
Product Name: 8I945GZME-RH
Version: x.x
Serial Number:
alex@deb-gate2:~$ lspci
00:00.0 Host bridge: Intel Corporation 82945G/GZ/P/PL Memory Controller Hub (rev 02)
00:02.0 VGA compatible controller: Intel Corporation 82945G/GZ Integrated Graphics Controller (rev 02)
00:1b.0 Audio device: Intel Corporation 82801G (ICH7 Family) High Definition Audio Controller (rev 01)
00:1d.0 USB Controller: Intel Corporation 82801G (ICH7 Family) USB UHCI Controller #1 (rev 01)
00:1d.1 USB Controller: Intel Corporation 82801G (ICH7 Family) USB UHCI Controller #2 (rev 01)
00:1d.2 USB Controller: Intel Corporation 82801G (ICH7 Family) USB UHCI Controller #3 (rev 01)
00:1d.3 USB Controller: Intel Corporation 82801G (ICH7 Family) USB UHCI Controller #4 (rev 01)
00:1d.7 USB Controller: Intel Corporation 82801G (ICH7 Family) USB2 EHCI Controller (rev 01)
00:1e.0 PCI bridge: Intel Corporation 82801 PCI Bridge (rev e1)
00:1f.0 ISA bridge: Intel Corporation 82801GB/GR (ICH7 Family) LPC Interface Bridge (rev 01)
00:1f.2 IDE interface: Intel Corporation 82801GB/GR/GH (ICH7 Family) SATA IDE Controller (rev 01)
00:1f.3 SMBus: Intel Corporation 82801G (ICH7 Family) SMBus Controller (rev 01)
01:00.0 Ethernet controller: Intel Corporation 82557/8/9/0/1 Ethernet Pro 100 (rev 08)
01:01.0 Ethernet controller: VIA Technologies, Inc. VT6105/VT6106S [Rhine-III] (rev 8b)
01:02.0 Ethernet controller: VIA Technologies, Inc. VT6105/VT6106S [Rhine-III] (rev 8b)
alex@deb-gate2:~$Сейчас попробую протестировать вынутый диск - возможно он вполне нормален.
Всем спасибо за внимание!