Перегревается процессор.

[Bizdelnick]

Это уже настроено, только толку от этого нет

Как настроено? Конфиг в студию. Сервис включён?

[Alex K.]

Как настроено? Конфиг в студию. Сервис включён?

Код: Выделить всё

@debian:~$ cat /etc/cpufreqd.conf
# this is a comment
# see CPUFREQD.CONF(5) manpage for a complete reference
#
# Note: ondemand/conservative Profiles are disabled because
#       they are not available on many platforms.

[General]
pidfile=/var/run/cpufreqd.pid
poll_interval=2
verbosity=4
#enable_remote=1
#remote_group=root
[/General]

#[acpi]
#acpid_socket=/var/run/acpid.socket
#[/acpi]

#[nforce2_atxp1]
#vcore_path=/some/path
#vcore_default=1500
#[/nforce2_atxp1]

#[sensors_plugin]
#sensors_conf=/some/file
#[/sensors_plugin]

[Profile]
name=On Demand High
minfreq=40%
maxfreq=100%
policy=ondemand
[/Profile]

[Profile]
name=On Demand Low
minfreq=20%
maxfreq=80%
policy=ondemand
[/Profile]

[Profile]
name=Performance High
minfreq=100%
maxfreq=100%
policy=performance
#exec_post=echo 8 > /proc/acpi/sony/brightness
[/Profile]

[Profile]
name=Performance Low
minfreq=80%
maxfreq=80%
policy=performance
[/Profile]

[Profile]
name=Powersave High
minfreq=60%
maxfreq=60%
policy=powersave
[/Profile]

[Profile]
name=Powersave Low
minfreq=40%
maxfreq=40%
policy=powersave
[/Profile]

#[Profile]
#name=Conservative High
#minfreq=33%
#maxfreq=100%
#policy=conservative
#[/Profile]
#
#[Profile]
#name=Conservative Low
#minfreq=0%
#maxfreq=66%
#policy=conservative
#[/Profile]

##
# Basic states
##
# when AC use performance mode
[Rule]
name=AC Rule
ac=on                    # (on/off)
profile=Performance High
[/Rule]

# stay in performance mode for the first minutes
[Rule]
name=AC Off - High Power
ac=off                   # (on/off)
battery_interval=70-100
#exec_post=echo 5 > /proc/acpi/sony/brightness
profile=Performance Low
[/Rule]

# conservative mode when not AC
[Rule]
name=AC Off - Medium Battery
ac=off                   # (on/off)
battery_interval=30-70
#exec_post=echo 3 > /proc/acpi/sony/brightness
profile=Powersave High
[/Rule]

# conservative mode when not AC
[Rule]
name=AC Off - Low Battery
ac=off                   # (on/off)
battery_interval=0-30
#exec_post=echo 3 > /proc/acpi/sony/brightness
profile=Powersave Low
[/Rule]

##
# Special Rules
##
# CPU Too hot!
[Rule]
name=CPU Too Hot
acpi_temperature=55-100
cpu_interval=50-100
profile=Performance Low
[/Rule]

# use performance mode if I'm watching a movie
# I don't care for batteries!
# But don't heat too much.
[Rule]
name=Movie Watcher
programs=xine,mplayer,gmplayer
battery_interval=0-100
acpi_temperature=0-60
cpu_interval=0-100
profile=Performance High
[/Rule]

Это(то, что ниже) до перезагрузки:

Код: Выделить всё

@debian:~$ su
Пароль:
root@debian:~# cpufreq-set --governor ondemand --cpu 1
root@debian:~# cpufreq-set --governor ondemand --cpu 0
root@debian:~# exit
exit
alex@debian:~$ cat /sys/devices/system/cpu/cpu1/cpufreq/scaling_governor
ondemand
alex@debian:~$ cat /sys/devices/system/cpu/cpu0/cpufreq/scaling_governor
ondemand

~# cpufreq-info
cpufrequtils 008: cpufreq-info (C) Dominik Brodowski 2004-2009
Report errors and bugs to cpufreq@vger.kernel.org, please.
analyzing CPU 0:
  driver: powernow-k8
  CPUs which run at the same hardware frequency: 0
  CPUs which need to have their frequency coordinated by software: 0
  maximum transition latency: 1000 ns.
  hardware limits: 1000 MHz - 2.00 GHz
  available frequency steps: 2.00 GHz, 1000 MHz
  available cpufreq governors: userspace, conservative, powersave, ondemand, performance
  current policy: frequency should be within 2.00 GHz and 2.00 GHz.
                  The governor "ondemand" may decide which speed to use
                  within this range.
  current CPU frequency is 2.00 GHz (asserted by call to hardware).
  cpufreq stats: 2.00 GHz:100,00%, 1000 MHz:0,00%
analyzing CPU 1:
  driver: powernow-k8
  CPUs which run at the same hardware frequency: 1
  CPUs which need to have their frequency coordinated by software: 1
  maximum transition latency: 1000 ns.
  hardware limits: 1000 MHz - 2.00 GHz
  available frequency steps: 2.00 GHz, 1000 MHz
  available cpufreq governors: userspace, conservative, powersave, ondemand, performance
  current policy: frequency should be within 2.00 GHz and 2.00 GHz.
                  The governor "ondemand" may decide which speed to use
                  within this range.
  current CPU frequency is 2.00 GHz (asserted by call to hardware).
  cpufreq stats: 2.00 GHz:100,00%, 1000 MHz:0,00%

В /etc/modules

Код: Выделить всё

~# cat /etc/modules
# /etc/modules: kernel modules to load at boot time.
#
# This file contains the names of kernel modules that should be loaded
# at boot time, one per line. Lines beginning with "#" are ignored.
# Parameters can be specified after the module name.

firewire-sbp2
loop
powernow-k8
cpufreq_ondemand

В памяти:

Код: Выделить всё

root@debian:~# lsmod|grep powernow
powernow_k8            17618  0
mperf                  12453  1 powernow_k8
processor              8157  1 powernow_k8

А автозагрузке:

Код: Выделить всё

debian:/etc/init.d$ ls
loadcpufreq
cpufreqd                sysfsutils
cpufrequtils

После перезагрузки:

Код: Выделить всё

root@debian:~# cpufreq-info
cpufrequtils 008: cpufreq-info (C) Dominik Brodowski 2004-2009
Report errors and bugs to cpufreq@vger.kernel.org, please.
analyzing CPU 0:
  driver: powernow-k8
  CPUs which run at the same hardware frequency: 0
  CPUs which need to have their frequency coordinated by software: 0
  maximum transition latency: 1000 ns.
  hardware limits: 1000 MHz - 2.00 GHz
  available frequency steps: 2.00 GHz, 1000 MHz
  available cpufreq governors: userspace, conservative, powersave, ondemand, performance
  current policy: frequency should be within 2.00 GHz and 2.00 GHz.
                  The governor "performance" may decide which speed to use
                  within this range.
  current CPU frequency is 2.00 GHz (asserted by call to hardware).
  cpufreq stats: 2.00 GHz:100,00%, 1000 MHz:0,00%
analyzing CPU 1:
  driver: powernow-k8
  CPUs which run at the same hardware frequency: 1
  CPUs which need to have their frequency coordinated by software: 1
  maximum transition latency: 1000 ns.
  hardware limits: 1000 MHz - 2.00 GHz
  available frequency steps: 2.00 GHz, 1000 MHz
  available cpufreq governors: userspace, conservative, powersave, ondemand, performance
  current policy: frequency should be within 2.00 GHz and 2.00 GHz.
                  The governor "performance" may decide which speed to use
                  within this range.
  current CPU frequency is 2.00 GHz (asserted by call to hardware).
  cpufreq stats: 2.00 GHz:100,00%, 1000 MHz:0,00%

Проблему решил так:
закоментировал в /etc/cpufreqd.conf все режимы, кроме ondemand, после выполнил это:

Код: Выделить всё

root@debian:~# cpufreq-set --governor ondemand --cpu 1
root@debian:~# cpufreq-set --governor ondemand --cpu 0

перезагрузил, изменениия сохранились:

Код: Выделить всё

alex@debian:~$ cat /sys/devices/system/cpu/cpu1/cpufreq/scaling_governor
ondemand
alex@debian:~$ cat /sys/devices/system/cpu/cpu0/cpufreq/scaling_governor
ondemand

Спасибо всем за помощь, буду считать, что проблема решена.