Линукс на лаптопах, ноутах и прочем - 2

[BlackStar]

mk86 я ничего специально не делал, оно само так стало

[chubaks]

всем здарова ))))
я хочу себе ща взять ноут IBM ThinkPad X22 - на нем проц 733 либо 800 Мгц + оперативка 256 (думаю сразу сменить на 512)....вроде по описанию максимум оперативки 640 Мб...можно ли гиг поставить ??? иль ограничение в материнке ???
у кого нить есть подобный девайс ??? Были ли какие-то проблеммы с установкой ????
Thank$

[chubaks]

из астрахани есть кто ??? мож поможите выбрать плиз бук недорогой,бу за 9-10 %)

[gnomru]

Приветствую форумчане, недавно приобрел toshiba satellite L40-14B, кроме вай-фай все заработало, если кому удалось его запустить подскажите как. edubuntu 7.10 с LXF98. Зарание спасибо.

[wrtc1t]

У меня возник трабл после настройки dpkg-xserver xorg пропал звук. Что бы это могло быть? На ноуте крутится Дебиан. Ноут MSI V600

[A.S.]

..можно ли гиг поставить ???

нет, только 640 .ThinkPad X20, X21, X22, X23, X24 Hardware Maintenance Manual (March 2002)

Были ли какие-то проблеммы с установкой ????

раз
два
три

[ptolemy]

я снес все разделы, создал новые и отформатировал их, потому что прежняя таблица разделов была какая-то кривая, и ни cfdisk, ни акронис работать с ней не захотели (а ведь сначала думал поставить Линукс второй системой). Не пойму, неужели это из CMOS берется?!

CMOS - маленький, туда такое не влезет. А по поводу Acronis - я брал самую последнюю версию. Старые версии Acronis, действительно ничего сделать не могли.

[CrazyYozhik]

Доброе время суток!
столкнулся с такой проблемой:
имеется ноутбук AcerAspire 5102AWLMi, имеется 2 операционные системы WinXP и Mandriva 2008 PP
также имеется всеми известная сетевая карточка Realtek RTL8139/810x Family Fast Ethernet NIC
одним прекрасным днём ось (Мандрива) перестала видеть эту карточку, причем как то странно, интерфейс eth0 есть, поднимается, пишет что работает, но ни одна лампочка на сетевой не горит(
Решился на повторную переустановку, карта заработала!!... но ровно до первой перезагрузки( после чего снова такая же проблема
что посоветуете, уважаемые эксперты? Сам я не сильно разбираюсь в линуксе, сеть худо-бедно настроить смогу, но что касается оборудования и ядра - для меня тёмный лес
выводы комманд lspci, lsmod, dmesg, ifconfig прикладываю ниже
З.Ы.: Поиском пользовался,даже нашёл где то похожую проблему, но там всё решилось перестановкой карты из одного слота в другой, у меня к сожалению так не получиться((..а в винде кстати всё работает
заранее спасибо)

DMESG:

Код:

Linux version 2.6.22.9-laptop-1mdv (lcapitulino@n5.mandriva.com) (gcc version 4.2.2 20070909 (prerelease) (4.2.2-0.RC.1mdv2008.0)) #1 SMP Thu Sep 27 04:17:10 CEST 2007 BIOS-provided physical RAM map: BIOS-e820: 0000000000000000 - 000000000009dc00 (usable) BIOS-e820: 000000000009dc00 - 00000000000a0000 (reserved) BIOS-e820: 00000000000d0000 - 0000000000100000 (reserved) BIOS-e820: 0000000000100000 - 000000001be90000 (usable) BIOS-e820: 000000001be90000 - 000000001be9a000 (ACPI data) BIOS-e820: 000000001be9a000 - 000000001bf00000 (ACPI NVS) BIOS-e820: 000000001bf00000 - 0000000020000000 (reserved) BIOS-e820: 00000000e0000000 - 00000000f0000000 (reserved) BIOS-e820: 00000000fec00000 - 00000000fec10000 (reserved) BIOS-e820: 00000000fee00000 - 00000000fee01000 (reserved) BIOS-e820: 00000000fff80000 - 0000000100000000 (reserved) 0MB HIGHMEM available. 446MB LOWMEM available. found SMP MP-table at 000f8110 Entering add_active_range(0, 0, 114320) 0 entries of 256 used Zone PFN ranges: DMA 0 -> 4096 Normal 4096 -> 114320 HighMem 114320 -> 114320 early_node_map[1] active PFN ranges 0: 0 -> 114320 On node 0 totalpages: 114320 DMA zone: 32 pages used for memmap DMA zone: 0 pages reserved DMA zone: 4064 pages, LIFO batch:0 Normal zone: 861 pages used for memmap Normal zone: 109363 pages, LIFO batch:31 HighMem zone: 0 pages used for memmap DMI present. ACPI: RSDP 000F8040, 0014 (r0 ACRSYS) ACPI: RSDT 1BE91C50, 0038 (r1 ACRSYS ACRPRDCT 6040000 LTP 0) ACPI: FACP 1BE99C5E, 0074 (r1 ATI Bowfin 6040000 ATI F4240) ACPI: DSDT 1BE91C88, 7FD6 (r1 Acer Navarro 6040000 MSFT 3000000) ACPI: FACS 1BE9AFC0, 0040 ACPI: SLIC 1BE99CD2, 0176 (r1 ACRSYS ACRPRDCT 6040000 LOHR 0) ACPI: APIC 1BE99E48, 0046 (r1 PTLTD APIC 6040000 LTP 0) ACPI: MCFG 1BE99E8E, 003C (r1 PTLTD MCFG 6040000 LTP 0) ACPI: SSDT 1BE99ECA, 0136 (r1 PTLTD POWERNOW 6040000 LTP 1) ATI board detected. Disabling timer routing over 8254. ACPI: PM-Timer IO Port: 0x8008 ACPI: Local APIC address 0xfee00000 ACPI: LAPIC (acpi_id[0x00] lapic_id[0x00] enabled) Processor #0 15:12 APIC version 16 ACPI: LAPIC_NMI (acpi_id[0x00] high edge lint[0x1]) ACPI: IOAPIC (id[0x01] address[0xfec00000] gsi_base[0]) IOAPIC[0]: apic_id 1, version 33, address 0xfec00000, GSI 0-23 ACPI: IRQ9 used by override. Enabling APIC mode: Flat. Using 1 I/O APICs Using ACPI (MADT) for SMP configuration information Allocating PCI resources starting at 30000000 (gap: 20000000:c0000000) swsusp: Registered nosave memory region: 000000000009d000 - 000000000009e000 swsusp: Registered nosave memory region: 000000000009e000 - 00000000000a0000 swsusp: Registered nosave memory region: 00000000000a0000 - 00000000000d0000 swsusp: Registered nosave memory region: 00000000000d0000 - 0000000000100000 Built 1 zonelists. Total pages: 113427 Kernel command line: BOOT_IMAGE=Mandriva_Linux_2008 root=/dev/sda6 resume=/dev/sda7 splash=silent vga=788 bootsplash: silent mode. mapped APIC to ffffd000 (fee00000) mapped IOAPIC to ffffc000 (fec00000) Enabling fast FPU save and restore... done. Enabling unmasked SIMD FPU exception support... done. Initializing CPU#0 PID hash table entries: 2048 (order: 11, 8192 bytes) Detected 2194.802 MHz processor. Console: colour dummy device 80x25 Dentry cache hash table entries: 65536 (order: 6, 262144 bytes) Inode-cache hash table entries: 32768 (order: 5, 131072 bytes) Memory: 447656k/457280k available (2129k kernel code, 8528k reserved, 689k data, 280k init, 0k highmem, 0k BadRAM) virtual kernel memory layout: fixmap : 0xffe16000 - 0xfffff000 (1956 kB) pkmap : 0xff800000 - 0xffc00000 (4096 kB) vmalloc : 0xdc800000 - 0xff7fe000 ( 559 MB) lowmem : 0xc0000000 - 0xdbe90000 ( 446 MB) .init : 0xc03c8000 - 0xc040e000 ( 280 kB) .data : 0xc0314767 - 0xc03c0c84 ( 689 kB) .text : 0xc0100000 - 0xc0314767 (2129 kB) Checking if this processor honours the WP bit even in supervisor mode... Ok. Calibrating delay using timer specific routine.. 4392.65 BogoMIPS (lpj=21963274) Security Framework v1.0.0 initialized Mount-cache hash table entries: 512 CPU: After generic identify, caps: 078bfbff ebd3fbff 00000000 00000000 00002001 00000000 0000001d CPU: L1 I Cache: 64K (64 bytes/line), D cache 64K (64 bytes/line) CPU: L2 Cache: 512K (64 bytes/line) CPU: After all inits, caps: 078bfbff ebd3fbff 00000000 00000410 00002001 00000000 0000001d Intel machine check architecture supported. Intel machine check reporting enabled on CPU#0. Compat vDSO mapped to ffffe000. Checking 'hlt' instruction... OK. SMP alternatives: switching to UP code Freeing SMP alternatives: 12k freed Early unpacking initramfs... done Freeing initrd memory: 921k freed ACPI: Core revision 20070126 ACPI: Looking for DSDT in initramfs... error, file /DSDT.aml not found. CPU0: AMD Turion&#153; 64 Mobile Technology MK-38 stepping 02 Total of 1 processors activated (4392.65 BogoMIPS). ENABLING IO-APIC IRQs ..TIMER: vector=0x31 apic1=0 pin1=0 apic2=-1 pin2=-1 Brought up 1 CPUs Booting paravirtualized kernel on bare hardware NET: Registered protocol family 16 ACPI: bus type pci registered PCI: Using MMCONFIG PCI: No mmconfig possible on device 00:18 Setting up standard PCI resources ACPI: EC: Look up EC in DSDT ACPI: EC: GPE = 0x10, I/O: command/status = 0x66, data = 0x62 ACPI: System BIOS is requesting _OSI(Linux) ACPI: Please test with "acpi_osi=!Linux" Please send dmidecode to linux-acpi@vger.kernel.org ACPI: Interpreter enabled ACPI: (supports S0 S3 S4 S5) ACPI: Using IOAPIC for interrupt routing ACPI: EC: GPE = 0x10, I/O: command/status = 0x66, data = 0x62 ACPI: PCI Root Bridge [PCI0] (0000:00) PCI: Probing PCI hardware (bus 00) PCI: Transparent bridge - 0000:00:14.4 ACPI: PCI Interrupt Routing Table [\_SB_.PCI0._PRT] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.PB4_._PRT] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.PB5_._PRT] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.BB4_._PRT] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.BB5_._PRT] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.P2P_._PRT] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.AGP_._PRT] ACPI: PCI Interrupt Link [LNKA] (IRQs 10 11) *0, disabled. ACPI: PCI Interrupt Link [LNKB] (IRQs 10 11) *0, disabled. ACPI: PCI Interrupt Link [LNKC] (IRQs 10 11) *0, disabled. ACPI: PCI Interrupt Link [LNKD] (IRQs 10 11) *0, disabled. ACPI: PCI Interrupt Link [LNKE] (IRQs 10 11) *0, disabled. ACPI: PCI Interrupt Link [LNKF] (IRQs 10 11) *0, disabled. ACPI: PCI Interrupt Link [LNKG] (IRQs 10 11) *0, disabled. ACPI: PCI Interrupt Link [LNKH] (IRQs 10 11) *0, disabled. ACPI: PCI Interrupt Link [LNKU] (IRQs 3 4 5 7) *0, disabled. Linux Plug and Play Support v0.97 © Adam Belay pnp: PnP ACPI init ACPI: bus type pnp registered pnp: PnP ACPI: found 10 devices ACPI: ACPI bus type pnp unregistered PnPBIOS: Disabled PCI: Using ACPI for IRQ routing PCI: If a device doesn't work, try "pci=routeirq". If it helps, post a report PCI: Cannot allocate resource region 7 of bridge 0000:00:04.0 PCI: Cannot allocate resource region 8 of bridge 0000:00:04.0 PCI: Cannot allocate resource region 9 of bridge 0000:00:04.0 PCI: Cannot allocate resource region 7 of bridge 0000:00:05.0 PCI: Cannot allocate resource region 8 of bridge 0000:00:05.0 PCI: Cannot allocate resource region 0 of device 0000:02:00.0 ACPI: RTC can wake from S4 pnp: 00:01: iomem range 0xe0000000-0xefffffff could not be reserved pnp: 00:01: iomem range 0xfec00000-0xfec00fff could not be reserved pnp: 00:01: iomem range 0xfee00000-0xfee00fff could not be reserved pnp: 00:08: ioport range 0x1080-0x1080 has been reserved pnp: 00:08: ioport range 0x40b-0x40b has been reserved pnp: 00:08: ioport range 0x4d0-0x4d1 has been reserved pnp: 00:08: ioport range 0x4d6-0x4d6 has been reserved pnp: 00:09: iomem range 0xe0000-0xfffff could not be reserved pnp: 00:09: iomem range 0xfff00000-0xffffffff could not be reserved pnp: 00:09: iomem range 0x0-0xfff could not be reserved Time: tsc clocksource has been installed. PCI: Bridge: 0000:00:01.0 IO window: 9000-9fff MEM window: d0100000-d01fffff PREFETCH window: d4000000-d7ffffff PCI: Bridge: 0000:00:04.0 IO window: disabled. MEM window: 34000000-340fffff PREFETCH window: disabled. PCI: Bridge: 0000:00:05.0 IO window: disabled. MEM window: disabled. PREFETCH window: disabled. PCI: Bus 7, cardbus bridge: 0000:06:04.0 IO window: 0000a400-0000a4ff IO window: 0000a800-0000a8ff PREFETCH window: 30000000-33ffffff MEM window: 38000000-3bffffff PCI: Bridge: 0000:00:14.4 IO window: a000-afff MEM window: d0300000-d03fffff PREFETCH window: 30000000-33ffffff PCI: Enabling device 0000:00:04.0 (0000 -> 0002) PCI: Setting latency timer of device 0000:00:04.0 to 64 PCI: Setting latency timer of device 0000:00:05.0 to 64 ACPI: PCI Interrupt 0000:06:04.0[A] -> GSI 20 (level, low) -> IRQ 16 NET: Registered protocol family 2 IP route cache hash table entries: 4096 (order: 2, 16384 bytes) TCP established hash table entries: 16384 (order: 5, 196608 bytes) TCP bind hash table entries: 16384 (order: 5, 131072 bytes) TCP: Hash tables configured (established 16384 bind 16384) TCP reno registered apm: BIOS not found. audit: initializing netlink socket (disabled) audit(1208089837.470:1): initialized Total HugeTLB memory allocated, 0 VFS: Disk quotas dquot_6.5.1 Dquot-cache hash table entries: 1024 (order 0, 4096 bytes) io scheduler noop registered io scheduler anticipatory registered io scheduler deadline registered io scheduler cfq registered (default) Boot video device is 0000:01:05.0 PCI: Setting latency timer of device 0000:00:04.0 to 64 assign_interrupt_mode Found MSI capability Allocate Port Service[0000:00:04.0:pcie00] Allocate Port Service[0000:00:04.0:pcie02] PCI: Setting latency timer of device 0000:00:05.0 to 64 assign_interrupt_mode Found MSI capability Allocate Port Service[0000:00:05.0:pcie00] Allocate Port Service[0000:00:05.0:pcie02] vesafb: framebuffer at 0xd4000000, mapped to 0xdc880000, using 3750k, total 16384k vesafb: mode is 800x600x16, linelength=1600, pages=16 vesafb: protected mode interface info at c000:53f8 vesafb: pmi: set display start = c00c5466, set palette = c00c54a0 vesafb: pmi: ports = 9010 9016 9054 9038 903c 905c 9000 9004 90b0 90b2 90b4 vesafb: scrolling: redraw vesafb: Truecolor: size=0:5:6:5, shift=0:11:5:0 bootsplash 3.1.6-2004/03/31: looking for picture...<6> silentjpeg size 222382 bytes,<6>...found (800x600, 222334 bytes, v3). Console: switching to colour frame buffer device 93x31 fb0: VESA VGA frame buffer device isapnp: Scanning for PnP cards... Switched to high resolution mode on CPU 0 isapnp: No Plug & Play device found Generic RTC Driver v1.07 Serial: 8250/16550 driver $Revision: 1.90 $ 4 ports, IRQ sharing enabled RAMDISK driver initialized: 16 RAM disks of 32000K size 1024 blocksize PNP: PS/2 Controller [PNP0303:KBC0,PNP0f13:MSS0] at 0x60,0x64 irq 1,12 i8042.c: Detected active multiplexing controller, rev 1.1. serio: i8042 KBD port at 0x60,0x64 irq 1 serio: i8042 AUX0 port at 0x60,0x64 irq 12 serio: i8042 AUX1 port at 0x60,0x64 irq 12 serio: i8042 AUX2 port at 0x60,0x64 irq 12 serio: i8042 AUX3 port at 0x60,0x64 irq 12 mice: PS/2 mouse device common for all mice input: AT Translated Set 2 keyboard as /class/input/input0 TCP cubic registered NET: Registered protocol family 1 Using IPI No-Shortcut mode BIOS EDD facility v0.16 2004-Jun-25, 1 devices found Freeing unused kernel memory: 280k freed SCSI subsystem initialized libata version 2.21 loaded. sata_sil 0000:00:12.0: version 2.2 PCI: Enabling device 0000:00:12.0 (0005 -> 0007) ACPI: PCI Interrupt 0000:00:12.0[A] -> GSI 22 (level, low) -> IRQ 17 scsi0 : sata_sil scsi1 : sata_sil ata1: SATA max UDMA/100 cmd 0xdc87c080 ctl 0xdc87c08a bmdma 0xdc87c000 irq 17 ata2: SATA max UDMA/100 cmd 0xdc87c0c0 ctl 0xdc87c0ca bmdma 0xdc87c008 irq 17 ata1: SATA link up 1.5 Gbps (SStatus 113 SControl 310) Synaptics Touchpad, model: 1, fw: 6.2, id: 0x1280b1, caps: 0xa04713/0x204000 ata1.00: ATA-7: ST980811AS, 3.ALD, max UDMA/133 ata1.00: 156301488 sectors, multi 16: LBA48 NCQ (depth 0/32) input: SynPS/2 Synaptics TouchPad as /class/input/input1 ata1.00: configured for UDMA/100 ata2: SATA link down (SStatus 0 SControl 310) scsi 0:0:0:0: Direct-Access ATA ST980811AS 3.AL PQ: 0 ANSI: 5 sd 0:0:0:0: [sda] 156301488 512-byte hardware sectors (80026 MB) sd 0:0:0:0: [sda] Write Protect is off sd 0:0:0:0: [sda] Mode Sense: 00 3a 00 00 sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA sd 0:0:0:0: [sda] 156301488 512-byte hardware sectors (80026 MB) sd 0:0:0:0: [sda] Write Protect is off sd 0:0:0:0: [sda] Mode Sense: 00 3a 00 00 sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA sda: sda1 sda2 < sda5 sda6 sda7 > sd 0:0:0:0: [sda] Attached SCSI disk swsusp: Marking nosave pages: 000000000009d000 - 0000000000100000 swsusp: Basic memory bitmaps created swsusp: Basic memory bitmaps freed kjournald starting. Commit interval 5 seconds EXT3-fs: mounted filesystem with ordered data mode. sd 0:0:0:0: Attached scsi generic sg0 type 0 pci_hotplug: PCI Hot Plug PCI Core version: 0.5 shpchp: Standard Hot Plug PCI Controller Driver version: 0.4 usbcore: registered new interface driver usbfs usbcore: registered new interface driver hub usbcore: registered new device driver usb ohci_hcd: 2006 August 04 USB 1.1 'Open' Host Controller (OHCI) Driver ACPI: PCI Interrupt 0000:00:13.0[A] -> GSI 19 (level, low) -> IRQ 18 ohci_hcd 0000:00:13.0: OHCI Host Controller ohci_hcd 0000:00:13.0: new USB bus registered, assigned bus number 1 ohci_hcd 0000:00:13.0: irq 18, io mem 0xd0005000 Linux agpgart interface v0.102 © Dave Jones usb usb1: configuration #1 chosen from 1 choice hub 1-0:1.0: USB hub found hub 1-0:1.0: 4 ports detected ACPI: PCI Interrupt 0000:00:13.1[A] -> GSI 19 (level, low) -> IRQ 18 ohci_hcd 0000:00:13.1: OHCI Host Controller ohci_hcd 0000:00:13.1: new USB bus registered, assigned bus number 2 ohci_hcd 0000:00:13.1: irq 18, io mem 0xd0006000 usb usb2: configuration #1 chosen from 1 choice hub 2-0:1.0: USB hub found hub 2-0:1.0: 4 ports detected ACPI: PCI Interrupt 0000:00:13.2[A] -> GSI 19 (level, low) -> IRQ 18 ehci_hcd 0000:00:13.2: EHCI Host Controller ehci_hcd 0000:00:13.2: new USB bus registered, assigned bus number 3 ehci_hcd 0000:00:13.2: irq 18, io mem 0xd0007000 ehci_hcd 0000:00:13.2: USB 2.0 started, EHCI 1.00, driver 10 Dec 2004 usb usb3: configuration #1 chosen from 1 choice hub 3-0:1.0: USB hub found hub 3-0:1.0: 8 ports detected ACPI: PCI Interrupt 0000:00:14.2[A] -> GSI 16 (level, low) -> IRQ 19 8139too Fast Ethernet driver 0.9.28 piix4_smbus 0000:00:14.0: Found 0000:00:14.0 device ACPI: PCI Interrupt 0000:06:01.0[A] -> GSI 21 (level, low) -> IRQ 20 eth0: RealTek RTL8139 at 0xdcc88000, 00:16:d4:d0:32:b3, IRQ 20 eth0: Identified 8139 chip type 'RTL-8100B/8139D' sdhci: Secure Digital Host Controller Interface driver sdhci: Copyright© Pierre Ossman sdhci: SDHCI controller found at 0000:06:04.2 [1524:0550] (rev 1) ACPI: PCI Interrupt 0000:06:04.2[B] -> GSI 23 (level, low) -> IRQ 21 mmc0: SDHCI at 0xd0300800 irq 21 DMA Yenta: CardBus bridge found at 0000:06:04.0 [1025:009f] Yenta: Using CSCINT to route CSC interrupts to PCI Yenta: Routing CardBus interrupts to PCI Yenta TI: socket 0000:06:04.0, mfunc 0x90501212, devctl 0x44 8139cp: 10/100 PCI Ethernet driver v1.3 (Mar 22, 2004) Yenta: ISA IRQ mask 0x0cf8, PCI irq 16 Socket status: 30000006 pcmcia: parent PCI bridge I/O window: 0xa000 - 0xafff cs: IO port probe 0xa000-0xafff: clean. pcmcia: parent PCI bridge Memory window: 0xd0300000 - 0xd03fffff pcmcia: parent PCI bridge Memory window: 0x30000000 - 0x33ffffff cs: IO port probe 0x100-0x3af: clean. cs: IO port probe 0x3e0-0x4ff: clean. cs: IO port probe 0x820-0x8ff: clean. cs: IO port probe 0xc00-0xcf7: excluding 0xc00-0xc07 0xc10-0xc17 0xc50-0xc57 0xc68-0xc6f 0xcd0-0xcdf cs: IO port probe 0xa00-0xaff: clean. acer_acpi: Acer Laptop ACPI Extras version 0.7 acer_acpi: Detected Acer WMID interface acer_acpi: Driver registered Non-volatile memory driver v1.2 ACPI: CPU0 (power states: C1[C1] C2[C2] C3[C3]) ACPI Exception (processor_core-0781): AE_NOT_FOUND, Processor Device is not present [20070126] Marking TSC unstable due to: possible TSC halt in C2. Time: acpi_pm clocksource has been installed. powernow-k8: Found 1 AMD Turion&#153; 64 Mobile Technology MK-38 processors (version 2.00.00) powernow-k8: 0 : fid 0xe (2200 MHz), vid 0xb powernow-k8: 1 : fid 0xc (2000 MHz), vid 0xd powernow-k8: 2 : fid 0xa (1800 MHz), vid 0xf powernow-k8: 3 : fid 0x8 (1600 MHz), vid 0x11 powernow-k8: 4 : fid 0x0 (800 MHz), vid 0x18 floppy0: no floppy controllers found Uniform Multi-Platform E-IDE driver Revision: 7.00alpha2 ide: Assuming 33MHz system bus speed for PIO modes; override with idebus=xx Initializing USB Mass Storage driver... usbcore: registered new interface driver usb-storage USB Mass Storage support registered. ATIIXP: IDE controller at PCI slot 0000:00:14.1 ACPI: PCI Interrupt 0000:00:14.1[A] -> GSI 16 (level, low) -> IRQ 19 ATIIXP: chipset revision 128 ATIIXP: not 100% native mode: will probe irqs later ide0: BM-DMA at 0x8420-0x8427, BIOS settings: hda:DMA, hdb:pio ATIIXP: simplex device: DMA disabled ide1: ATIIXP Bus-Master DMA disabled (BIOS) Probing IDE interface ide0... hda: PIONEER DVD-RW DVR-K17RS, ATAPI CD/DVD-ROM drive hda: selected mode 0x42 ide0 at 0x1f0-0x1f7,0x3f6 on irq 14 Probing IDE interface ide1... hda: ATAPI 31X DVD-ROM DVD-R-RAM CD-R/RW drive, 2000kB Cache, UDMA(33) Uniform CD-ROM driver Revision: 3.20 device-mapper: ioctl: 4.11.0-ioctl (2006-10-12) initialised: dm-devel@redhat.com EXT3 FS on sda6, internal journal Adding 763048k swap on /dev/sda7. Priority:-1 extents:1 across:763048k NTFS driver 2.1.28 [Flags: R/O DEBUG MODULE]. NTFS volume version 3.1. NTFS volume version 3.1. loop: module loaded ACPI: AC Adapter [ACAD] (on-line) Netfilter messages via NETLINK v0.30. nf_conntrack version 0.5.0 (3572 buckets, 28576 max) ACPI: Battery Slot [BAT1] (battery present) No dock devices found. Removing netfilter NETLINK layer. input: Power Button (FF) as /class/input/input2 ACPI: Power Button (FF) [PWRF] input: Lid Switch as /class/input/input3 ACPI: Lid Switch [LID] input: Power Button (CM) as /class/input/input4 ACPI: Power Button (CM) [PWRB] input: Sleep Button (CM) as /class/input/input5 ACPI: Sleep Button (CM) [SLPB] ACPI Exception (thermal-0400): AE_NOT_FOUND, Invalid active threshold [0] [20070126] ACPI: Thermal Zone [THRM] (56 C) ACPI: Video Device [VGA_AGP] (multi-head: yes rom: no post: no) ACPI: Video Device [VGA_PEG] (multi-head: yes rom: no post: no) NET: Registered protocol family 10 lo: Disabled Privacy Extensions Mobile IPv6 NET: Registered protocol family 17 eth0: link up, 100Mbps, full-duplex, lpa 0x41E1 ip_tables: © 2000-2006 Netfilter Core Team Netfilter messages via NETLINK v0.30. nf_conntrack version 0.5.0 (3572 buckets, 28576 max) ip6_tables: © 2000-2006 Netfilter Core Team ctnetlink v0.93: registering with nfnetlink. fglrx: module license 'Proprietary. © 2002 - ATI Technologies, Starnberg, GERMANY' taints kernel. [fglrx] Maximum main memory to use for locked dma buffers: 372 MBytes. [fglrx] USWC is disabled in module parameters [fglrx] PAT is disabled! [fglrx] module loaded - fglrx 8.40.4 [Jul 31 2007] on minor 0 ACPI: PCI Interrupt 0000:01:05.0[A] -> GSI 17 (level, low) -> IRQ 22 ClusterIP Version 0.8 loaded successfully [fglrx] total GART = 130023424 [fglrx] free GART = 114032640 [fglrx] max single GART = 114032640 [fglrx] total LFB = 67108864 [fglrx] free LFB = 52719616 [fglrx] max single LFB = 52719616 [fglrx] total Inv = 0 [fglrx] free Inv = 0 [fglrx] max single Inv = 0 [fglrx] total TIM = 0 PPP generic driver version 2.4.2 eth0: no IPv6 routers present bootsplash 3.1.6-2004/03/31: looking for picture...<6>...found (800x600, 14966 bytes, v3). bootsplash: status on console 0 changed to on bootsplash 3.1.6-2004/03/31: looking for picture...<6>...found (800x600, 14966 bytes, v3). bootsplash: status on console 1 changed to on bootsplash 3.1.6-2004/03/31: looking for picture...<6>...found (800x600, 14966 bytes, v3). bootsplash: status on console 2 changed to on bootsplash 3.1.6-2004/03/31: looking for picture...<6>...found (800x600, 14966 bytes, v3). bootsplash: status on console 3 changed to on bootsplash 3.1.6-2004/03/31: looking for picture...<6>...found (800x600, 14966 bytes, v3). bootsplash: status on console 4 changed to on bootsplash 3.1.6-2004/03/31: looking for picture...<6>...found (800x600, 14966 bytes, v3). bootsplash: status on console 5 changed to on NETDEV WATCHDOG: eth0: transmit timed out eth0: Transmit timeout, status 0d 0000 c07f media 10. eth0: Tx queue start entry 4 dirty entry 0. eth0: Tx descriptor 0 is 0008205a. (queue head) eth0: Tx descriptor 1 is 0008203c. eth0: Tx descriptor 2 is 0008204e. eth0: Tx descriptor 3 is 0008203c. eth0: link up, 100Mbps, full-duplex, lpa 0x41E1 NETDEV WATCHDOG: eth0: transmit timed out eth0: Transmit timeout, status 0d 0000 c07f media 10. eth0: Tx queue start entry 4 dirty entry 0. eth0: Tx descriptor 0 is 00082046. (queue head) eth0: Tx descriptor 1 is 0008203c. eth0: Tx descriptor 2 is 0008203c. eth0: Tx descriptor 3 is 00082116. eth0: link up, 100Mbps, full-duplex, lpa 0x41E1 NETDEV WATCHDOG: eth0: transmit timed out eth0: Transmit timeout, status 0d 0000 c07f media 10. eth0: Tx queue start entry 4 dirty entry 0. eth0: Tx descriptor 0 is 00082116. (queue head) eth0: Tx descriptor 1 is 00082116. eth0: Tx descriptor 2 is 00082104. eth0: Tx descriptor 3 is 000820f9. eth0: link up, 100Mbps, full-duplex, lpa 0x41E1 hda-intel: Invalid position buffer, using LPIB read method instead. Clocksource tsc unstable (delta = -136413377 ns) NETDEV WATCHDOG: eth0: transmit timed out eth0: Transmit timeout, status 0d 0000 c07f media 10. eth0: Tx queue start entry 4 dirty entry 0. eth0: Tx descriptor 0 is 0008203c. (queue head) eth0: Tx descriptor 1 is 000820f9. eth0: Tx descriptor 2 is 000820f9. eth0: Tx descriptor 3 is 00082168. eth0: link up, 100Mbps, full-duplex, lpa 0x41E1 ISO 9660 Extensions: Microsoft Joliet Level 3 ISO 9660 Extensions: RRIP_1991A NETDEV WATCHDOG: eth0: transmit timed out eth0: Transmit timeout, status 0d 0000 c07f media 10. eth0: Tx queue start entry 4 dirty entry 0. eth0: Tx descriptor 0 is 000820d8. (queue head) eth0: Tx descriptor 1 is 0008203c. eth0: Tx descriptor 2 is 00082046. eth0: Tx descriptor 3 is 00082168. eth0: link up, 100Mbps, full-duplex, lpa 0x41E1 NETDEV WATCHDOG: eth0: transmit timed out eth0: Transmit timeout, status 0d 0000 c07f media 10. eth0: Tx queue start entry 4 dirty entry 0. eth0: Tx descriptor 0 is 00082104. (queue head) eth0: Tx descriptor 1 is 00082168. eth0: Tx descriptor 2 is 0008205a. eth0: Tx descriptor 3 is 00082046. eth0: link up, 100Mbps, full-duplex, lpa 0x41E1 NETDEV WATCHDOG: eth0: transmit timed out eth0: Transmit timeout, status 0d 0000 c07f media 10. eth0: Tx queue start entry 4 dirty entry 0. eth0: Tx descriptor 0 is 0008203c. (queue head) eth0: Tx descriptor 1 is 0008203c. eth0: Tx descriptor 2 is 0008203c. eth0: Tx descriptor 3 is 0008203c. eth0: link up, 100Mbps, full-duplex, lpa 0x41E1 NETDEV WATCHDOG: eth0: transmit timed out eth0: Transmit timeout, status 0d 0000 c07f media 10. eth0: Tx queue start entry 4 dirty entry 0. eth0: Tx descriptor 0 is 0008203c. (queue head) eth0: Tx descriptor 1 is 0008203c. eth0: Tx descriptor 2 is 0008203c. eth0: Tx descriptor 3 is 0008203c. eth0: link up, 100Mbps, full-duplex, lpa 0x41E1 NETDEV WATCHDOG: eth0: transmit timed out eth0: Transmit timeout, status 0d 0000 c07f media 10. eth0: Tx queue start entry 4 dirty entry 0. eth0: Tx descriptor 0 is 0008203c. (queue head) eth0: Tx descriptor 1 is 0008203c. eth0: Tx descriptor 2 is 0008203c. eth0: Tx descriptor 3 is 0008203c. eth0: link up, 100Mbps, full-duplex, lpa 0x41E1 usb 3-1: new high speed USB device using ehci_hcd and address 2 usb 3-1: configuration #1 chosen from 1 choice scsi2 : SCSI emulation for USB Mass Storage devices usb-storage: device found at 2 usb-storage: waiting for device to settle before scanning scsi 2:0:0:0: Direct-Access Digitex Flash Disk 0.00 PQ: 0 ANSI: 2 sd 2:0:0:0: [sdb] 2015231 512-byte hardware sectors (1032 MB) sd 2:0:0:0: [sdb] Write Protect is off sd 2:0:0:0: [sdb] Mode Sense: 00 00 00 00 sd 2:0:0:0: [sdb] Assuming drive cache: write through sd 2:0:0:0: [sdb] 2015231 512-byte hardware sectors (1032 MB) sd 2:0:0:0: [sdb] Write Protect is off sd 2:0:0:0: [sdb] Mode Sense: 00 00 00 00 sd 2:0:0:0: [sdb] Assuming drive cache: write through sdb: sdb1 sd 2:0:0:0: [sdb] Attached SCSI removable disk sd 2:0:0:0: Attached scsi generic sg1 type 0 usb-storage: device scan complete FAT: utf8 is not a recommended IO charset for FAT filesystems, filesystem will be case sensitive!

LSPCI:

Код:

[root@localhost yozhik]# lspci 00:00.0 Host bridge: ATI Technologies Inc RS480 Host Bridge (rev 10) 00:01.0 PCI bridge: ATI Technologies Inc RS480 PCI Bridge 00:04.0 PCI bridge: ATI Technologies Inc RS480 PCI Bridge 00:05.0 PCI bridge: ATI Technologies Inc RS480 PCI Bridge 00:12.0 IDE interface: ATI Technologies Inc 4379 Serial ATA Controller (rev 80) 00:13.0 USB Controller: ATI Technologies Inc IXP SB400 USB Host Controller (rev 80) 00:13.1 USB Controller: ATI Technologies Inc IXP SB400 USB Host Controller (rev 80) 00:13.2 USB Controller: ATI Technologies Inc IXP SB400 USB2 Host Controller (rev 80) 00:14.0 SMBus: ATI Technologies Inc IXP SB400 SMBus Controller (rev 83) 00:14.1 IDE interface: ATI Technologies Inc Standard Dual Channel PCI IDE Controller (rev 80) 00:14.2 Audio device: ATI Technologies Inc SB450 HDA Audio (rev 01) 00:14.3 ISA bridge: ATI Technologies Inc IXP SB400 PCI-ISA Bridge (rev 80) 00:14.4 PCI bridge: ATI Technologies Inc IXP SB400 PCI-PCI Bridge (rev 80) 00:18.0 Host bridge: Advanced Micro Devices [AMD] K8 [Athlon64/Opteron] HyperTransport Technology Configuration 00:18.1 Host bridge: Advanced Micro Devices [AMD] K8 [Athlon64/Opteron] Address Map 00:18.2 Host bridge: Advanced Micro Devices [AMD] K8 [Athlon64/Opteron] DRAM Controller 00:18.3 Host bridge: Advanced Micro Devices [AMD] K8 [Athlon64/Opteron] Miscellaneous Control 01:05.0 VGA compatible controller: ATI Technologies Inc RS485 [Radeon Xpress 1100 IGP] 02:00.0 Ethernet controller: Atheros Communications, Inc. AR5006EG 802.11 b/g Wireless PCI Express Adapter (rev 01) 06:01.0 Ethernet controller: Realtek Semiconductor Co., Ltd. RTL-8139/8139C/8139C+ (rev 10) 06:04.0 CardBus bridge: ENE Technology Inc CB-712/4 Cardbus Controller (rev 10) 06:04.1 FLASH memory: ENE Technology Inc ENE PCI Memory Stick Card Reader Controller (rev 01) 06:04.2 Generic system peripheral [0805]: ENE Technology Inc ENE PCI Secure Digital Card Reader Controller (rev 01) 06:04.3 FLASH memory: ENE Technology Inc FLASH memory: ENE Technology Inc: (rev 01) 06:04.4 FLASH memory: ENE Technology Inc SD/MMC Card Reader Controller (rev 01)

LSMOD:

Код:

Module Size Used by isofs 31356 1 fglrx 726848 11 ppp_async 9856 0 ppp_generic 23348 1 ppp_async slhc 5984 1 ppp_generic crc_ccitt 2624 1 ppp_async iptable_raw 2688 0 xt_comment 2336 0 xt_policy 4256 0 xt_multiport 3808 4 ipt_ULOG 7748 0 ipt_TTL 2656 0 ipt_ttl 2336 0 ipt_TOS 2560 0 ipt_tos 2176 0 ipt_SAME 2880 0 ipt_REJECT 4288 4 ipt_REDIRECT 2720 0 ipt_recent 8344 0 ipt_owner 2464 0 ipt_NETMAP 2656 0 ipt_MASQUERADE 3872 0 ipt_LOG 6560 10 ipt_iprange 2336 0 ipt_ECN 3200 0 ipt_ecn 2656 0 ipt_CLUSTERIP 7460 0 ipt_ah 2368 0 ipt_addrtype 2336 0 nf_nat_tftp 2208 0 nf_nat_snmp_basic 9732 0 nf_nat_sip 4768 0 nf_nat_pptp 3552 0 nf_nat_proto_gre 3012 1 nf_nat_pptp nf_nat_irc 2816 0 nf_nat_h323 6720 0 nf_nat_ftp 3424 0 nf_nat_amanda 2560 0 ts_kmp 2592 5 nf_conntrack_amanda 4512 1 nf_nat_amanda nf_conntrack_tftp 5492 1 nf_nat_tftp nf_conntrack_sip 8788 1 nf_nat_sip nf_conntrack_proto_sctp 8520 0 nf_conntrack_pptp 6176 1 nf_nat_pptp nf_conntrack_proto_gre 5152 1 nf_conntrack_pptp nf_conntrack_netlink 23904 0 nf_conntrack_netbios_ns 3104 0 nf_conntrack_irc 6104 1 nf_nat_irc nf_conntrack_h323 48156 1 nf_nat_h323 nf_conntrack_ftp 8800 1 nf_nat_ftp xt_tcpmss 2688 0 xt_pkttype 2400 4 xt_physdev 3120 0 xt_NFQUEUE 2496 0 xt_NFLOG 2560 0 xt_MARK 2784 0 xt_mark 2400 0 xt_mac 2400 0 xt_limit 2944 0 xt_length 2464 0 xt_helper 2944 0 xt_hashlimit 8588 0 ip6_tables 12484 1 xt_hashlimit xt_dccp 3556 0 xt_conntrack 3040 0 xt_CONNMARK 3200 0 xt_connmark 2688 0 xt_CLASSIFY 2368 0 xt_tcpudp 3680 11 xt_state 2752 11 iptable_nat 7396 0 nf_nat 16140 14 ipt_SAME,ipt_REDIRECT,ipt_NETMAP,ipt_MASQUERADE,nf_nat_tftp,nf_nat_sip,nf_nat_pp tp,nf_nat_proto_gre,nf_nat_irc,nf_nat_h323,nf_nat_ftp,nf_nat_amanda,nf_conntrack _ netlink,iptable_nat nf_conntrack_ipv4 15148 13 iptable_nat nf_conntrack 54952 29 ipt_MASQUERADE,ipt_CLUSTERIP,nf_nat_tftp,nf_nat_snmp_basic,nf_nat_sip,nf_nat_ppt p,nf_nat_irc,nf_nat_h323,nf_nat_ftp,nf_nat_amanda,nf_conntrack_amanda,nf_conntra c k_tftp,nf_conntrack_sip,nf_conntrack_proto_sctp,nf_conntrack_pptp,nf_conntrack_p r oto_gre,nf_conntrack_netlink,nf_conntrack_netbios_ns,nf_conntrack_irc,nf_conntra c k_h323,nf_conntrack_ftp,xt_helper,xt_conntrack,xt_CONNMARK,xt_connmark,xt_state, i ptable_nat,nf_nat,nf_conntrack_ipv4 iptable_mangle 2976 1 nfnetlink 5080 4 nf_conntrack_netlink,nf_nat,nf_conntrack_ipv4,nf_conntrack iptable_filter 3136 1 ip_tables 11396 4 iptable_raw,iptable_nat,iptable_mangle,iptable_filter x_tables 12036 44 xt_comment,xt_policy,xt_multiport,ipt_ULOG,ipt_TTL,ipt_ttl,ipt_TOS,ipt_tos,ipt_S AME,ipt_REJECT,ipt_REDIRECT,ipt_recent,ipt_owner,ipt_NETMAP,ipt_MASQUERADE,ipt_L O G,ipt_iprange,ipt_ECN,ipt_ecn,ipt_CLUSTERIP,ipt_ah,ipt_addrtype,xt_tcpmss,xt_pkt t ype,xt_physdev,xt_NFQUEUE,xt_NFLOG,xt_MARK,xt_mark,xt_mac,xt_limit,xt_length,xt_ h elper,xt_hashlimit,ip6_tables,xt_dccp,xt_conntrack,xt_CONNMARK,xt_connmark,xt_CL A SSIFY,xt_tcpudp,xt_state,iptable_nat,ip_tables af_packet 17960 0 ipv6 249988 9 nf_conntrack_h323 snd_seq_dummy 3492 0 snd_seq_oss 29888 0 snd_seq_midi_event 6912 1 snd_seq_oss snd_seq 46800 5 snd_seq_dummy,snd_seq_oss,snd_seq_midi_event snd_seq_device 7276 3 snd_seq_dummy,snd_seq_oss,snd_seq snd_pcm_oss 37216 0 snd_mixer_oss 14784 1 snd_pcm_oss nls_cp437 6304 1 vfat 11040 1 fat 45852 1 vfat dm_zero 2528 0 video 15080 0 thermal 11304 0 sbs 16520 0 fan 4260 0 container 4032 0 button 6576 0 dock 7568 0 battery 10344 0 ac 4452 0 binfmt_misc 9416 1 loop 14276 0 nls_utf8 2496 4 ntfs 252840 2 dm_mirror 20224 0 dm_mod 48064 2 dm_zero,dm_mirror ide_cd 35200 1 atiixp 5616 0 [permanent] cpufreq_ondemand 7340 1 cpufreq_conservative 6600 0 cpufreq_powersave 2240 0 powernow_k8 14336 0 freq_table 4512 2 cpufreq_ondemand,powernow_k8 processor 25796 2 thermal,powernow_k8 amd64_agp 10180 0 nvram 8488 0 acer_acpi 12780 0 usb_storage 90276 1 ide_core 99748 3 ide_cd,atiixp,usb_storage pcmcia 33260 0 mmc_block 9508 0 yenta_socket 23628 1 8139cp 19712 0 rsrc_nonstatic 11904 1 yenta_socket sdhci 15244 0 pcmcia_core 33108 3 pcmcia,yenta_socket,rsrc_nonstatic mmc_core 23108 2 mmc_block,sdhci 8139too 22816 0 mii 5280 2 8139cp,8139too k8temp 5120 0 snd_hda_intel 284028 1 snd_pcm 69636 2 snd_pcm_oss,snd_hda_intel snd_timer 19652 2 snd_seq,snd_pcm snd_page_alloc 8456 2 snd_hda_intel,snd_pcm snd_hwdep 7492 1 snd_hda_intel snd 45092 11 snd_seq_oss,snd_seq,snd_seq_device,snd_pcm_oss,snd_mixer_oss,snd_hda_intel,snd_p cm,snd_timer,snd_hwdep soundcore 6624 1 snd shpchp 29812 0 pci_hotplug 27360 1 shpchp ehci_hcd 30732 0 ohci_hcd 19972 0 i2c_piix4 8332 0 i2c_core 20224 1 i2c_piix4 usbcore 118760 4 usb_storage,ehci_hcd,ohci_hcd ati_agp 7596 0 agpgart 27656 3 fglrx,amd64_agp,ati_agp joydev 8800 0 tsdev 7104 0 evdev 8448 6 sg 30488 0 ext3 118408 1 jbd 50504 1 ext3 scsi_wait_scan 1984 0 sd_mod 26272 7 sata_sil 8648 4 libata 108848 1 sata_sil scsi_mod 125356 5 usb_storage,sg,scsi_wait_scan,sd_mod,libata

IFCONFIG:

Код:

eth0 Link encap:Ethernet HWaddr 00:16:D4:D0:32:B3 inet addr:192.168.1.4 Bcast:192.168.1.255 Mask:255.255.255.0 inet6 addr: fe80::216:d4ff:fed0:32b3/64 Scope:Link UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:0 errors:0 dropped:0 overruns:0 frame:0 TX packets:0 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:0 (0.0 b) TX bytes:0 (0.0 b) Interrupt:20 Base address:0x8000 lo Link encap:Local Loopback inet addr:127.0.0.1 Mask:255.0.0.0 inet6 addr: ::1/128 Scope:Host UP LOOPBACK RUNNING MTU:16436 Metric:1 RX packets:458 errors:0 dropped:0 overruns:0 frame:0 TX packets:458 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:0 RX bytes:23220 (22.6 KiB) TX bytes:23220 (22.6 KiB)

[dakar]

Как установить Wi-Fi adapter?

Вопрос с Wi-Fi отпал сам по себе после апрельского обновления.

Но с обновлениями я бы посоветовал не торопится, сначала лучше определится с пакетами и возможными настройками и сконфигурировать систему, а потом обновлять

[dakar]

Ждущий и спящий режим на лаптопе

У меня на лаптопе (Tosiba Satellite-5005, Mandriva Powepack-2008/GNOME ) не работает спящий и ждущий режимы,
вернее в режим компьютер входит, но при выходе (включении) я получаю либо черный либо белый экран.


Можно ли что нибудь сделать? Или ждать нового обновления Мандривы?

[wrewolf]

у меня ASUS F3Ke есть проблема когда втыкаешь наушники звук в динамиках пропадает. Проблема в том что програмно можны выключить только звук в наушниках. а не на динамиках.
очень хотелось бы решить проблему. так как работаю с букой по ночам и люблю слушать музыку, а будить всех не хочу.

П.С.
WiFi настроен и работает. после установки вот такой вот штучки madwifi-ng-r2756+ar5007

[Iskan Der]

у меня ASUS F3Ke есть проблема когда втыкаешь наушники звук в динамиках пропадает. Проблема в том что програмно можны выключить только звук в наушниках. а не на динамиках.
очень хотелось бы решить проблему. так как работаю с букой по ночам и люблю слушать музыку, а будить всех не хочу.

Я так понял, нужно чтобы при втыкании наушников выключались динамики? Если пользуешься KDE, то там где-то в KMix есть такая опция - "Headphones Jack Sense", которую надо включить. Мне, во всяк, в свое время помогло

[wrewolf]

У меня русская версия, ничего подобного не нашел.
Есть закладка выключатели. Там HeadPhones оон отключает наушники, а не системные динамики.

[Iskan Der]

У меня русская версия, ничего подобного не нашел.
Есть закладка выключатели. Там HeadPhones оон отключает наушники, а не системные динамики.

Хм, у меня оно выглядит как на приаттаченном скрине. Дистриб - Mandriva 2008 Free

[zwey]

Может маленько не в тему, но замучило любопытство.
FreeBSD (OpenBSD) ктонибудь на ноуты ставил? Как обстоит дело с железом? Да и ваапще какие грабли могут быть.

[Preferance]

Как на Мандриве нормально установить power manager?
Из опций пока что только "ввести в спящий режим"
Аккумулятора хватает часа на 3, а в Виндах было 10, что делать

[vadeus]

Как на Мандриве нормально установить power manager?
Из опций пока что только "ввести в спящий режим"
Аккумулятора хватает часа на 3, а в Виндах было 10, что делать

Так там есть KPowersave - вот в нём и настраиваются режимы энергосбережения, или можно ещё KLaptop поковырять.

[kaaboeld]

Интегрированое видео и память

Приветствую.
Попытаюсь сформулировать вопрос:
Есть ноутбук acer 2920z с интегрированной видео картой на базер 865 intel чипсета. У видео карты своей памяти 8mb, в windows (vista предустановленная) выделяется доля RAM (обычное дело как и всегда с интегрированным железом) соотвественно при 2gb RAM (макс. на этой модели) в сумме получаем VRAM 358mb.
В линуксе Ubuntu 7.10 x64 и openSuse 10.3 x64 судя по системной информации и быстро действенности 3d приложений работает только базовая VRAM 8mb. Вопрос как и возможно ли в принципе "подсосать" RAM?

Уточнение:
В биосе настроек нет, биос был перепрошит до версии 1.13.
Гуглил и искал по различным(разноязычным Smiley ) форумам и блогам - инфы не нашел, единственное, что часто встречается так это обратный процесс перекачки VRAM to RAM.

Заранее благодарю за ответы.

[plab]

Господа, посоветуйте ноутбук для линукса, основные требования - большой и качественный экран, наличие выхода DVI, видеоадаптер на котором будет работать xrandr то есть либо радеон либо интел, обязательно wi-fi, обязательно cf картридер, и нужно чтобы ВСЕ девайсы полностью работали в линуксах... Ноутбук предполагается использовать для работы с текстом, так что мощный процессор и много памяти не нужно... Бюджет не лимитирован...

[Rever]

Radeon x1250 совместим с Ubuntu? Помогите

[falanger]

Убунта приживется на старом ноуте с Р2-300 и 192 метрами оперативки? В ноуте комбинированный чипсет, часть от 443ВХ часть от 371АВ/ЕВ.

[Current_Density]

falanger

Ubuntu is available for PC, 64-Bit and Mac architectures. At least 256 MB of RAM is required to run the desktop install CD. Install requires at least 4 GB of disk space.

Есть убунта специально для слабых компов.

[Rever]

У меня при загрузке Убунты пишет что экран найден но не подходит по конфигурации. Убунту 7.10

[haRUNg]

Добрый день!
Кто нибудь устанавливал Linux на ноутбук Samsung R25plus-FE06, если да, то какие грабли?

[Ariel]

Добрый день

2.6.21.5 - Slackware 12 ноутбук с чипсетом intel 965gm, не моу включить direct rendering, хотя все модули висят i915, intel, dri, agp_gart, etc;
вот логи :

Xorg.0

Код:

X Window System Version 1.3.0 Release Date: 19 April 2007 X Protocol Version 11, Revision 0, Release 1.3 Build Operating System: Slackware 12.0 Slackware Linux Project Current Operating System: Linux darkstar 2.6.21.5 #1 SMP Sat Apr 12 21:13:45 EEST 2008 i686 Build Date: 09 May 2007 Before reporting problems, check http://wiki.x.org to make sure that you have the latest version. Module Loader present Markers: (--) probed, (**) from config file, (==) default setting, (++) from command line, (!!) notice, (II) informational, (WW) warning, (EE) error, (NI) not implemented, (??) unknown. (==) Log file: "/var/log/Xorg.0.log", Time: Tue Apr 15 23:25:16 2008 (==) Using config file: "/etc/X11/xorg.conf" (==) ServerLayout "Simple Layout" (**) |-->Screen "Screen 1" (0) (**) | |-->Monitor "My Monitor" (**) | |-->Device "** Intel i810 (generic) [i810]" (**) |-->Input Device "Mouse1" (**) |-->Input Device "Keyboard1" (**) FontPath set to: /usr/share/fonts/TTF, /usr/share/fonts/OTF, /usr/share/fonts/Type1, /usr/share/fonts/misc, /usr/share/fonts/75dpi/:unscaled, /usr/lib/X11/fonts/misc/, /usr/lib/X11/fonts/75dpi/:unscaled, /usr/lib/X11/fonts/100dpi/:unscaled, /usr/lib/X11/fonts/Speedo/, /usr/lib/X11/fonts/Type1/, /usr/lib/X11/fonts/TTF/, /usr/lib/X11/fonts/OTF/, /usr/lib/X11/fonts/cyrillic/, /usr/lib/X11/fonts/75dpi/, /usr/lib/X11/fonts/100dpi/ (==) RgbPath set to "/usr/share/X11/rgb" (==) ModulePath set to "/usr/lib/xorg/modules" (II) Open ACPI successful (/var/run/acpid.socket) (II) Loader magic: 0x81dcd60 (II) Module ABI versions: X.Org ANSI C Emulation: 0.3 X.Org Video Driver: 1.2 X.Org XInput driver : 0.7 X.Org Server Extension : 0.3 X.Org Font Renderer : 0.5 (II) Loader running on linux (II) LoadModule: "pcidata" (II) Loading /usr/lib/xorg/modules//libpcidata.so (II) Module pcidata: vendor="X.Org Foundation" compiled for 1.3.0, module version = 1.0.0 ABI class: X.Org Video Driver, version 1.2 (--) using VT number 7 (II) PCI: PCI scan (all values are in hex) (II) PCI: 00:00:0: chip 8086,2a00 card 1734,1108 rev 03 class 06,00,00 hdr 00 (II) PCI: 00:02:0: chip 8086,2a02 card 1734,1108 rev 03 class 03,00,00 hdr 80 (II) PCI: 00:02:1: chip 8086,2a03 card 1734,1108 rev 03 class 03,80,00 hdr 80 (II) PCI: 00:1a:0: chip 8086,2834 card 1734,1108 rev 03 class 0c,03,00 hdr 80 (II) PCI: 00:1a:1: chip 8086,2835 card 1734,1108 rev 03 class 0c,03,00 hdr 00 (II) PCI: 00:1a:7: chip 8086,283a card 1734,1108 rev 03 class 0c,03,20 hdr 00 (II) PCI: 00:1b:0: chip 8086,284b card 1734,1108 rev 03 class 04,03,00 hdr 00 (II) PCI: 00:1c:0: chip 8086,283f card 0000,0000 rev 03 class 06,04,00 hdr 81 (II) PCI: 00:1c:2: chip 8086,2843 card 0000,0000 rev 03 class 06,04,00 hdr 81 (II) PCI: 00:1c:3: chip 8086,2845 card 0000,0000 rev 03 class 06,04,00 hdr 81 (II) PCI: 00:1d:0: chip 8086,2830 card 1734,1108 rev 03 class 0c,03,00 hdr 80 (II) PCI: 00:1d:1: chip 8086,2831 card 1734,1108 rev 03 class 0c,03,00 hdr 00 (II) PCI: 00:1d:2: chip 8086,2832 card 1734,1108 rev 03 class 0c,03,00 hdr 00 (II) PCI: 00:1d:7: chip 8086,2836 card 1734,1108 rev 03 class 0c,03,20 hdr 00 (II) PCI: 00:1e:0: chip 8086,2448 card 0000,0000 rev f3 class 06,04,01 hdr 01 (II) PCI: 00:1f:0: chip 8086,2815 card 1734,1108 rev 03 class 06,01,00 hdr 80 (II) PCI: 00:1f:1: chip 8086,2850 card 1734,1108 rev 03 class 01,01,8a hdr 00 (II) PCI: 00:1f:2: chip 8086,2829 card 1734,1108 rev 03 class 01,06,01 hdr 00 (II) PCI: 00:1f:3: chip 8086,283e card 1734,1108 rev 03 class 0c,05,00 hdr 00 (II) PCI: 04:00:0: chip 8086,4222 card 8086,1001 rev 02 class 02,80,00 hdr 00 (II) PCI: 06:00:0: chip 10ec,8136 card 1734,1108 rev 01 class 02,00,00 hdr 00 (II) PCI: End of PCI scan (II) Intel Bridge workaround enabled (II) Host-to-PCI bridge: (II) Bus 0: bridge is at (0:0:0), (0,0,8), BCTRL: 0x0008 (VGA_EN is set) (II) Bus 0 I/O range: [0] -1 0 0x00000000 - 0x0000ffff (0x10000) IX (II) Bus 0 non-prefetchable memory range: [0] -1 0 0x00000000 - 0xffffffff (0x0) MX (II) Bus 0 prefetchable memory range: [0] -1 0 0x00000000 - 0xffffffff (0x0) MX (II) PCI-to-PCI bridge: (II) Bus 2: bridge is at (0:28:0), (0,2,3), BCTRL: 0x0004 (VGA_EN is cleared) (II) Bus 2 I/O range: [0] -1 0 0x00002000 - 0x000020ff (0x100) IX [1] -1 0 0x00002400 - 0x000024ff (0x100) IX [2] -1 0 0x00002800 - 0x000028ff (0x100) IX [3] -1 0 0x00002c00 - 0x00002cff (0x100) IX (II) Bus 2 non-prefetchable memory range: [0] -1 0 0xf6000000 - 0xf7ffffff (0x2000000) MX (II) Bus 2 prefetchable memory range: [0] -1 0 0xf0000000 - 0xf1ffffff (0x2000000) MX (II) PCI-to-PCI bridge: (II) Bus 4: bridge is at (0:28:2), (0,4,5), BCTRL: 0x0004 (VGA_EN is cleared) (II) Bus 4 I/O range: [0] -1 0 0x00003000 - 0x000030ff (0x100) IX [1] -1 0 0x00003400 - 0x000034ff (0x100) IX [2] -1 0 0x00003800 - 0x000038ff (0x100) IX [3] -1 0 0x00003c00 - 0x00003cff (0x100) IX (II) Bus 4 non-prefetchable memory range: [0] -1 0 0xf8000000 - 0xf9ffffff (0x2000000) MX (II) Bus 4 prefetchable memory range: [0] -1 0 0xf2000000 - 0xf3ffffff (0x2000000) MX (II) PCI-to-PCI bridge: (II) Bus 6: bridge is at (0:28:3), (0,6,7), BCTRL: 0x0004 (VGA_EN is cleared) (II) Bus 6 I/O range: [0] -1 0 0x00004000 - 0x000040ff (0x100) IX [1] -1 0 0x00004400 - 0x000044ff (0x100) IX [2] -1 0 0x00004800 - 0x000048ff (0x100) IX [3] -1 0 0x00004c00 - 0x00004cff (0x100) IX (II) Bus 6 non-prefetchable memory range: [0] -1 0 0xfa000000 - 0xfbffffff (0x2000000) MX (II) Bus 6 prefetchable memory range: [0] -1 0 0xf4000000 - 0xf5ffffff (0x2000000) MX (II) Subtractive PCI-to-PCI bridge: (II) Bus 8: bridge is at (0:30:0), (0,8,8), BCTRL: 0x0004 (VGA_EN is cleared) (II) PCI-to-ISA bridge: (II) Bus -1: bridge is at (0:31:0), (0,-1,-1), BCTRL: 0x0008 (VGA_EN is set) (--) PCI:*(0:2:0) Intel Corporation Mobile Integrated Graphics Controller rev 3, Mem @ 0xfc000000/20, 0xd0000000/28, I/O @ 0x1800/3 (--) PCI: (0:2:1) Intel Corporation Mobile Integrated Graphics Controller rev 3, Mem @ 0xfc100000/20 (II) Addressable bus resource ranges are [0] -1 0 0x00000000 - 0xffffffff (0x0) MX [1] -1 0 0x00000000 - 0x0000ffff (0x10000) IX (II) OS-reported resource ranges: [0] -1 0 0x00100000 - 0x3fffffff (0x3ff00000) MXE(B) [1] -1 0 0x000f0000 - 0x000fffff (0x10000) MX [2] -1 0 0x000c0000 - 0x000effff (0x30000) MX [3] -1 0 0x00000000 - 0x0009ffff (0xa0000) MX [4] -1 0 0x0000ffff - 0x0000ffff (0x1) IX [5] -1 0 0x00000000 - 0x000000ff (0x100) IX (II) Active PCI resource ranges: [0] -1 0 0xfa000000 - 0xfa000fff (0x1000) MX [1] -1 0 0xf8000000 - 0xf8000fff (0x1000) MX [2] -1 0 0x88000000 - 0x880000ff (0x100) MX [3] -1 0 0xfc404000 - 0xfc4047ff (0x800) MX [4] -1 0 0xfc404c00 - 0xfc404fff (0x400) MX [5] -1 0 0xfc400000 - 0xfc403fff (0x4000) MX [6] -1 0 0xfc404800 - 0xfc404bff (0x400) MX [7] -1 0 0xfc100000 - 0xfc1fffff (0x100000) MX(B) [8] -1 0 0xd0000000 - 0xdfffffff (0x10000000) MX(B) [9] -1 0 0xfc000000 - 0xfc0fffff (0x100000) MX(B) [10] -1 0 0x00004000 - 0x000040ff (0x100) IX [11] -1 0 0x00001c20 - 0x00001c3f (0x20) IX [12] -1 0 0x000018e0 - 0x000018ff (0x20) IX [13] -1 0 0x000018d0 - 0x000018d3 (0x4) IX [14] -1 0 0x000018d8 - 0x000018df (0x8) IX [15] -1 0 0x000018d4 - 0x000018d7 (0x4) IX [16] -1 0 0x00001c00 - 0x00001c07 (0x8) IX [17] -1 0 0x00001810 - 0x0000181f (0x10) IX [18] -1 0 0x000001f0 - 0x000001f0 (0x1) IX [19] -1 0 0x000001f0 - 0x000001f7 (0x8) IX [20] -1 0 0x000001f0 - 0x000001f0 (0x1) IX [21] -1 0 0x000001f0 - 0x000001f7 (0x8) IX [22] -1 0 0x000018a0 - 0x000018bf (0x20) IX [23] -1 0 0x00001880 - 0x0000189f (0x20) IX [24] -1 0 0x00001860 - 0x0000187f (0x20) IX [25] -1 0 0x00001840 - 0x0000185f (0x20) IX [26] -1 0 0x00001820 - 0x0000183f (0x20) IX [27] -1 0 0x00001800 - 0x00001807 (0x8) IX(B) (II) Active PCI resource ranges after removing overlaps: [0] -1 0 0xfa000000 - 0xfa000fff (0x1000) MX [1] -1 0 0xf8000000 - 0xf8000fff (0x1000) MX [2] -1 0 0x88000000 - 0x880000ff (0x100) MX [3] -1 0 0xfc404000 - 0xfc4047ff (0x800) MX [4] -1 0 0xfc404c00 - 0xfc404fff (0x400) MX [5] -1 0 0xfc400000 - 0xfc403fff (0x4000) MX [6] -1 0 0xfc404800 - 0xfc404bff (0x400) MX [7] -1 0 0xfc100000 - 0xfc1fffff (0x100000) MX(B) [8] -1 0 0xd0000000 - 0xdfffffff (0x10000000) MX(B) [9] -1 0 0xfc000000 - 0xfc0fffff (0x100000) MX(B) [10] -1 0 0x00004000 - 0x000040ff (0x100) IX [11] -1 0 0x00001c20 - 0x00001c3f (0x20) IX [12] -1 0 0x000018e0 - 0x000018ff (0x20) IX [13] -1 0 0x000018d0 - 0x000018d3 (0x4) IX [14] -1 0 0x000018d8 - 0x000018df (0x8) IX [15] -1 0 0x000018d4 - 0x000018d7 (0x4) IX [16] -1 0 0x00001c00 - 0x00001c07 (0x8) IX [17] -1 0 0x00001810 - 0x0000181f (0x10) IX [18] -1 0 0x000001f0 - 0x000001f0 (0x1) IX [19] -1 0 0x000001f0 - 0x000001f7 (0x8) IX [20] -1 0 0x000001f0 - 0x000001f0 (0x1) IX [21] -1 0 0x000001f0 - 0x000001f7 (0x8) IX [22] -1 0 0x000018a0 - 0x000018bf (0x20) IX [23] -1 0 0x00001880 - 0x0000189f (0x20) IX [24] -1 0 0x00001860 - 0x0000187f (0x20) IX [25] -1 0 0x00001840 - 0x0000185f (0x20) IX [26] -1 0 0x00001820 - 0x0000183f (0x20) IX [27] -1 0 0x00001800 - 0x00001807 (0x8) IX(B) (II) OS-reported resource ranges after removing overlaps with PCI: [0] -1 0 0x00100000 - 0x3fffffff (0x3ff00000) MXE(B) [1] -1 0 0x000f0000 - 0x000fffff (0x10000) MX [2] -1 0 0x000c0000 - 0x000effff (0x30000) MX [3] -1 0 0x00000000 - 0x0009ffff (0xa0000) MX [4] -1 0 0x0000ffff - 0x0000ffff (0x1) IX [5] -1 0 0x00000000 - 0x000000ff (0x100) IX (II) All system resource ranges: [0] -1 0 0x00100000 - 0x3fffffff (0x3ff00000) MXE(B) [1] -1 0 0x000f0000 - 0x000fffff (0x10000) MX [2] -1 0 0x000c0000 - 0x000effff (0x30000) MX [3] -1 0 0x00000000 - 0x0009ffff (0xa0000) MX [4] -1 0 0xfa000000 - 0xfa000fff (0x1000) MX [5] -1 0 0xf8000000 - 0xf8000fff (0x1000) MX [6] -1 0 0x88000000 - 0x880000ff (0x100) MX [7] -1 0 0xfc404000 - 0xfc4047ff (0x800) MX [8] -1 0 0xfc404c00 - 0xfc404fff (0x400) MX [9] -1 0 0xfc400000 - 0xfc403fff (0x4000) MX [10] -1 0 0xfc404800 - 0xfc404bff (0x400) MX [11] -1 0 0xfc100000 - 0xfc1fffff (0x100000) MX(B) [12] -1 0 0xd0000000 - 0xdfffffff (0x10000000) MX(B) [13] -1 0 0xfc000000 - 0xfc0fffff (0x100000) MX(B) [14] -1 0 0x0000ffff - 0x0000ffff (0x1) IX [15] -1 0 0x00000000 - 0x000000ff (0x100) IX [16] -1 0 0x00004000 - 0x000040ff (0x100) IX [17] -1 0 0x00001c20 - 0x00001c3f (0x20) IX [18] -1 0 0x000018e0 - 0x000018ff (0x20) IX [19] -1 0 0x000018d0 - 0x000018d3 (0x4) IX [20] -1 0 0x000018d8 - 0x000018df (0x8) IX [21] -1 0 0x000018d4 - 0x000018d7 (0x4) IX [22] -1 0 0x00001c00 - 0x00001c07 (0x8) IX [23] -1 0 0x00001810 - 0x0000181f (0x10) IX [24] -1 0 0x000001f0 - 0x000001f0 (0x1) IX [25] -1 0 0x000001f0 - 0x000001f7 (0x8) IX [26] -1 0 0x000001f0 - 0x000001f0 (0x1) IX [27] -1 0 0x000001f0 - 0x000001f7 (0x8) IX [28] -1 0 0x000018a0 - 0x000018bf (0x20) IX [29] -1 0 0x00001880 - 0x0000189f (0x20) IX [30] -1 0 0x00001860 - 0x0000187f (0x20) IX [31] -1 0 0x00001840 - 0x0000185f (0x20) IX [32] -1 0 0x00001820 - 0x0000183f (0x20) IX [33] -1 0 0x00001800 - 0x00001807 (0x8) IX(B) (II) LoadModule: "dbe" (II) Loading /usr/lib/xorg/modules/extensions//libdbe.so (II) Module dbe: vendor="X.Org Foundation" compiled for 1.3.0, module version = 1.0.0 Module class: X.Org Server Extension ABI class: X.Org Server Extension, version 0.3 (II) Loading extension DOUBLE-BUFFER (II) LoadModule: "extmod" (II) Loading /usr/lib/xorg/modules/extensions//libextmod.so (II) Module extmod: vendor="X.Org Foundation" compiled for 1.3.0, module version = 1.0.0 Module class: X.Org Server Extension ABI class: X.Org Server Extension, version 0.3 (II) Loading extension SHAPE (II) Loading extension MIT-SUNDRY-NONSTANDARD (II) Loading extension BIG-REQUESTS (II) Loading extension SYNC (II) Loading extension MIT-SCREEN-SAVER (II) Loading extension XC-MISC (II) Loading extension XFree86-VidModeExtension (II) Loading extension XFree86-Misc (II) Loading extension DPMS (II) Loading extension TOG-CUP (II) Loading extension Extended-Visual-Information (II) Loading extension XVideo (II) Loading extension XVideo-MotionCompensation (II) Loading extension X-Resource (II) LoadModule: "freetype" (II) Loading /usr/lib/xorg/modules/fonts//libfreetype.so (II) Module freetype: vendor="X.Org Foundation & the After X-TT Project" compiled for 1.3.0, module version = 2.1.0 Module class: X.Org Font Renderer ABI class: X.Org Font Renderer, version 0.5 (II) Loading font FreeType (II) LoadModule: "glx" (II) Loading /usr/lib/xorg/modules/extensions//libglx.so (II) Module glx: vendor="X.Org Foundation" compiled for 1.3.0, module version = 1.0.0 ABI class: X.Org Server Extension, version 0.3 (==) AIGLX enabled (II) Loading extension GLX (II) LoadModule: "dri" (II) Loading /usr/lib/xorg/modules/extensions//libdri.so (II) Module dri: vendor="X.Org Foundation" compiled for 1.3.0, module version = 1.0.0 ABI class: X.Org Server Extension, version 0.3 (II) Loading extension XFree86-DRI (II) LoadModule: "i810" (II) Loading /usr/lib/xorg/modules/drivers//i810_drv.so (II) Module i810: vendor="X.Org Foundation" compiled for 1.3.0, module version = 2.0.0 Module class: X.Org Video Driver ABI class: X.Org Video Driver, version 1.2 (II) LoadModule: "mouse" (II) Loading /usr/lib/xorg/modules/input//mouse_drv.so (II) Module mouse: vendor="X.Org Foundation" compiled for 7.2.0, module version = 1.1.1 Module class: X.Org XInput Driver ABI class: X.Org XInput driver, version 0.7 (II) LoadModule: "kbd" (II) Loading /usr/lib/xorg/modules/input//kbd_drv.so (II) Module kbd: vendor="X.Org Foundation" compiled for 1.2.99.905, module version = 1.1.0 Module class: X.Org XInput Driver ABI class: X.Org XInput driver, version 0.7 (II) intel: Driver for Intel Integrated Graphics Chipsets: i810, i810-dc100, i810e, i815, i830M, 845G, 852GM/855GM, 865G, 915G, E7221 (i915), 915GM, 945G, 945GM, 965G, 965G, 965Q, 946GZ, 965GM (II) Primary Device is: PCI 00:02:0 (--) Assigning device section with no busID to primary device (WW) intel: No matching Device section for instance (BusID PCI:0:2:1) found (--) Chipset 965GM found (II) resource ranges after xf86ClaimFixedResources() call: [0] -1 0 0x00100000 - 0x3fffffff (0x3ff00000) MXE(B) [1] -1 0 0x000f0000 - 0x000fffff (0x10000) MX [2] -1 0 0x000c0000 - 0x000effff (0x30000) MX [3] -1 0 0x00000000 - 0x0009ffff (0xa0000) MX [4] -1 0 0xfa000000 - 0xfa000fff (0x1000) MX [5] -1 0 0xf8000000 - 0xf8000fff (0x1000) MX [6] -1 0 0x88000000 - 0x880000ff (0x100) MX [7] -1 0 0xfc404000 - 0xfc4047ff (0x800) MX [8] -1 0 0xfc404c00 - 0xfc404fff (0x400) MX [9] -1 0 0xfc400000 - 0xfc403fff (0x4000) MX [10] -1 0 0xfc404800 - 0xfc404bff (0x400) MX [11] -1 0 0xfc100000 - 0xfc1fffff (0x100000) MX(B) [12] -1 0 0xd0000000 - 0xdfffffff (0x10000000) MX(B) [13] -1 0 0xfc000000 - 0xfc0fffff (0x100000) MX(B) [14] -1 0 0x0000ffff - 0x0000ffff (0x1) IX [15] -1 0 0x00000000 - 0x000000ff (0x100) IX [16] -1 0 0x00004000 - 0x000040ff (0x100) IX [17] -1 0 0x00001c20 - 0x00001c3f (0x20) IX [18] -1 0 0x000018e0 - 0x000018ff (0x20) IX [19] -1 0 0x000018d0 - 0x000018d3 (0x4) IX [20] -1 0 0x000018d8 - 0x000018df (0x8) IX [21] -1 0 0x000018d4 - 0x000018d7 (0x4) IX [22] -1 0 0x00001c00 - 0x00001c07 (0x8) IX [23] -1 0 0x00001810 - 0x0000181f (0x10) IX [24] -1 0 0x000001f0 - 0x000001f0 (0x1) IX [25] -1 0 0x000001f0 - 0x000001f7 (0x8) IX [26] -1 0 0x000001f0 - 0x000001f0 (0x1) IX [27] -1 0 0x000001f0 - 0x000001f7 (0x8) IX [28] -1 0 0x000018a0 - 0x000018bf (0x20) IX [29] -1 0 0x00001880 - 0x0000189f (0x20) IX [30] -1 0 0x00001860 - 0x0000187f (0x20) IX [31] -1 0 0x00001840 - 0x0000185f (0x20) IX [32] -1 0 0x00001820 - 0x0000183f (0x20) IX [33] -1 0 0x00001800 - 0x00001807 (0x8) IX(B) (II) resource ranges after probing: [0] -1 0 0x00100000 - 0x3fffffff (0x3ff00000) MXE(B) [1] -1 0 0x000f0000 - 0x000fffff (0x10000) MX [2] -1 0 0x000c0000 - 0x000effff (0x30000) MX [3] -1 0 0x00000000 - 0x0009ffff (0xa0000) MX [4] -1 0 0xfa000000 - 0xfa000fff (0x1000) MX [5] -1 0 0xf8000000 - 0xf8000fff (0x1000) MX [6] -1 0 0x88000000 - 0x880000ff (0x100) MX [7] -1 0 0xfc404000 - 0xfc4047ff (0x800) MX [8] -1 0 0xfc404c00 - 0xfc404fff (0x400) MX [9] -1 0 0xfc400000 - 0xfc403fff (0x4000) MX [10] -1 0 0xfc404800 - 0xfc404bff (0x400) MX [11] -1 0 0xfc100000 - 0xfc1fffff (0x100000) MX(B) [12] -1 0 0xd0000000 - 0xdfffffff (0x10000000) MX(B) [13] -1 0 0xfc000000 - 0xfc0fffff (0x100000) MX(B) [14] 0 0 0x000a0000 - 0x000affff (0x10000) MS [15] 0 0 0x000b0000 - 0x000b7fff (0x8000) MS [16] 0 0 0x000b8000 - 0x000bffff (0x8000) MS [17] -1 0 0x0000ffff - 0x0000ffff (0x1) IX [18] -1 0 0x00000000 - 0x000000ff (0x100) IX [19] -1 0 0x00004000 - 0x000040ff (0x100) IX [20] -1 0 0x00001c20 - 0x00001c3f (0x20) IX [21] -1 0 0x000018e0 - 0x000018ff (0x20) IX [22] -1 0 0x000018d0 - 0x000018d3 (0x4) IX [23] -1 0 0x000018d8 - 0x000018df (0x8) IX [24] -1 0 0x000018d4 - 0x000018d7 (0x4) IX [25] -1 0 0x00001c00 - 0x00001c07 (0x8) IX [26] -1 0 0x00001810 - 0x0000181f (0x10) IX [27] -1 0 0x000001f0 - 0x000001f0 (0x1) IX [28] -1 0 0x000001f0 - 0x000001f7 (0x8) IX [29] -1 0 0x000001f0 - 0x000001f0 (0x1) IX [30] -1 0 0x000001f0 - 0x000001f7 (0x8) IX [31] -1 0 0x000018a0 - 0x000018bf (0x20) IX [32] -1 0 0x00001880 - 0x0000189f (0x20) IX [33] -1 0 0x00001860 - 0x0000187f (0x20) IX [34] -1 0 0x00001840 - 0x0000185f (0x20) IX [35] -1 0 0x00001820 - 0x0000183f (0x20) IX [36] -1 0 0x00001800 - 0x00001807 (0x8) IX(B) [37] 0 0 0x000003b0 - 0x000003bb (0xc) IS [38] 0 0 0x000003c0 - 0x000003df (0x20) IS (II) Setting vga for screen 0. (II) Loading sub module "int10" (II) LoadModule: "int10" (II) Loading /usr/lib/xorg/modules//libint10.so (II) Module int10: vendor="X.Org Foundation" compiled for 1.3.0, module version = 1.0.0 ABI class: X.Org Video Driver, version 1.2 (II) Loading sub module "vbe" (II) LoadModule: "vbe" (II) Loading /usr/lib/xorg/modules//libvbe.so (II) Module vbe: vendor="X.Org Foundation" compiled for 1.3.0, module version = 1.1.0 ABI class: X.Org Video Driver, version 1.2 (II) Loading sub module "vgahw" (II) LoadModule: "vgahw" (II) Loading /usr/lib/xorg/modules//libvgahw.so (II) Module vgahw: vendor="X.Org Foundation" compiled for 1.3.0, module version = 0.1.0 ABI class: X.Org Video Driver, version 1.2 (**) intel(0): Depth 24, (--) framebuffer bpp 32 (==) intel(0): RGB weight 888 (==) intel(0): Default visual is TrueColor (II) intel(0): Integrated Graphics Chipset: Intel® 965GM (--) intel(0): Chipset: "965GM" (--) intel(0): Linear framebuffer at 0xD0000000 (--) intel(0): IO registers at addr 0xFC000000 (II) intel(0): 2 display pipes available. (==) intel(0): Using XAA for acceleration (--) intel(0): Will try to allocate texture pool for old Mesa 3D driver. (II) intel(0): Will try to reserve 32768 kiB of AGP aperture space for the DRM memory manager. (II) Loading sub module "ddc" (II) LoadModule: "ddc"(II) Module already built-in (II) Loading sub module "i2c" (II) LoadModule: "i2c"(II) Module already built-in (II) intel(0): Output VGA using monitor section My Monitor (II) intel(0): I2C bus "CRTDDC_A" initialized. (II) intel(0): Output LVDS has no monitor section (II) intel(0): I2C bus "LVDSDDC_C" initialized. (II) intel(0): I2C device "LVDSDDC_C:ddc2" registered at address 0xA0. (II) intel(0): I2C device "LVDSDDC_C:ddc2" removed. (II) intel(0): EDID for output LVDS (II) intel(0): Manufacturer: CPT Model: 1415 Serial#: 0 (II) intel(0): Year: 2007 Week: 34 (II) intel(0): EDID Version: 1.3 (II) intel(0): Digital Display Input (II) intel(0): Max H-Image Size [cm]: horiz.: 33 vert.: 21 (II) intel(0): Gamma: 2.20 (II) intel(0): No DPMS capabilities specified; RGB/Color Display (II) intel(0): First detailed timing is preferred mode (II) intel(0): redX: 0.613 redY: 0.336 greenX: 0.311 greenY: 0.563 (II) intel(0): blueX: 0.152 blueY: 0.131 whiteX: 0.315 whiteY: 0.329 (II) intel(0): Manufacturer's mask: 0 (II) intel(0): Supported additional Video Mode: (II) intel(0): clock: 68.9 MHz Image Size: 331 x 207 mm (II) intel(0): h_active: 1280 h_sync: 1304 h_sync_end 1336 h_blank_end 1408 h_border: 0 (II) intel(0): v_active: 800 v_sync: 801 v_sync_end 804 v_blanking: 813 v_border: 0 (II) intel(0): CPT (II) intel(0): CLAA154WB05A (II) intel(0): EDID (in hex): (II) intel(0): 00ffffffffffff000e14151400000000 (II) intel(0): 22110103802115780a092d9d564f9027 (II) intel(0): 21505400000001010101010101010101 (II) intel(0): 010101010101ea1a008050200d301820 (II) intel(0): 13004bcf100000190000000f00202020 (II) intel(0): 2020202020206e050f00000000fe0043 (II) intel(0): 50540a202020202020202020000000fe (II) intel(0): 00434c414131353457423035412000c1 (II) intel(0): EDID vendor "CPT", prod id 5141 (II) Loading sub module "int10" (II) LoadModule: "int10" (II) Reloading /usr/lib/xorg/modules//libint10.so (II) intel(0): initializing int10 (WW) intel(0): Bad V_BIOS checksum (II) intel(0): Primary V_BIOS segment is: 0xc000 (II) intel(0): VESA BIOS detected (II) intel(0): VESA VBE Version 3.0 (II) intel(0): VESA VBE Total Mem: 7616 kB (II) intel(0): VESA VBE OEM: Intel®GM965/PM965/GL960 Graphics Chip Accelerated VGA BIOS (II) intel(0): VESA VBE OEM Software Rev: 1.0 (II) intel(0): VESA VBE OEM Vendor: Intel Corporation (II) intel(0): VESA VBE OEM Product: Intel®GM965/PM965/GL960 Graphics Controller (II) intel(0): VESA VBE OEM Product Rev: Hardware Version 0.0 (II) intel(0): I2C bus "SDVOCTRL_E for SDVOB" initialized. (II) intel(0): I2C device "SDVOCTRL_E for SDVOB:SDVO Controller B" registered at address 0x70. (II) intel(0): No SDVO device found on SDVOB (II) intel(0): I2C device "SDVOCTRL_E for SDVOB:SDVO Controller B" removed. (II) intel(0): I2C bus "SDVOCTRL_E for SDVOB" removed. (II) intel(0): I2C bus "SDVOCTRL_E for SDVOC" initialized. (II) intel(0): I2C device "SDVOCTRL_E for SDVOC:SDVO Controller C" registered at address 0x72. (II) intel(0): No SDVO device found on SDVOC (II) intel(0): I2C device "SDVOCTRL_E for SDVOC:SDVO Controller C" removed. (II) intel(0): I2C bus "SDVOCTRL_E for SDVOC" removed. (II) intel(0): Output TV has no monitor section (II) intel(0): Output VGA disconnected (II) intel(0): EDID for output VGA (II) intel(0): Output LVDS connected (II) intel(0): I2C device "LVDSDDC_C:ddc2" registered at address 0xA0. (II) intel(0): I2C device "LVDSDDC_C:ddc2" removed. (II) intel(0): EDID for output LVDS (II) intel(0): Manufacturer: CPT Model: 1415 Serial#: 0 (II) intel(0): Year: 2007 Week: 34 (II) intel(0): EDID Version: 1.3 (II) intel(0): Digital Display Input (II) intel(0): Max H-Image Size [cm]: horiz.: 33 vert.: 21 (II) intel(0): Gamma: 2.20 (II) intel(0): No DPMS capabilities specified; RGB/Color Display (II) intel(0): First detailed timing is preferred mode (II) intel(0): redX: 0.613 redY: 0.336 greenX: 0.311 greenY: 0.563 (II) intel(0): blueX: 0.152 blueY: 0.131 whiteX: 0.315 whiteY: 0.329 (II) intel(0): Manufacturer's mask: 0 (II) intel(0): Supported additional Video Mode: (II) intel(0): clock: 68.9 MHz Image Size: 331 x 207 mm (II) intel(0): h_active: 1280 h_sync: 1304 h_sync_end 1336 h_blank_end 1408 h_border: 0 (II) intel(0): v_active: 800 v_sync: 801 v_sync_end 804 v_blanking: 813 v_border: 0 (II) intel(0): CPT (II) intel(0): CLAA154WB05A (II) intel(0): EDID (in hex): (II) intel(0): 00ffffffffffff000e14151400000000 (II) intel(0): 22110103802115780a092d9d564f9027 (II) intel(0): 21505400000001010101010101010101 (II) intel(0): 010101010101ea1a008050200d301820 (II) intel(0): 13004bcf100000190000000f00202020 (II) intel(0): 2020202020206e050f00000000fe0043 (II) intel(0): 50540a202020202020202020000000fe (II) intel(0): 00434c414131353457423035412000c1 (II) intel(0): EDID vendor "CPT", prod id 5141 (II) intel(0): Not using default mode "640x350" (vrefresh out of range) (II) intel(0): Not using default mode "640x400" (vrefresh out of range) (II) intel(0): Not using default mode "720x400" (vrefresh out of range) (II) intel(0): Not using default mode "640x480" (vrefresh out of range) (II) intel(0): Not using default mode "640x480" (vrefresh out of range) (II) intel(0): Not using default mode "640x480" (vrefresh out of range) (II) intel(0): Not using default mode "800x600" (vrefresh out of range) (II) intel(0): Not using default mode "800x600" (vrefresh out of range) (II) intel(0): Not using default mode "800x600" (vrefresh out of range) (II) intel(0): Not using default mode "800x600" (vrefresh out of range) (II) intel(0): Not using default mode "1024x768" (vrefresh out of range) (II) intel(0): Not using default mode "1024x768" (vrefresh out of range) (II) intel(0): Not using default mode "1024x768" (vrefresh out of range) (II) intel(0): Not using default mode "1152x864" (height too large for virtual size) (II) intel(0): Not using default mode "1280x960" (height too large for virtual size) (II) intel(0): Not using default mode "1280x960" (height too large for virtual size) (II) intel(0): Not using default mode "1280x1024" (height too large for virtual size) (II) intel(0): Not using default mode "1280x1024" (height too large for virtual size) (II) intel(0): Not using default mode "1280x1024" (height too large for virtual size) (II) intel(0): Not using default mode "1600x1200" (height too large for virtual size) (II) intel(0): Not using default mode "1600x1200" (height too large for virtual size) (II) intel(0): Not using default mode "1600x1200" (height too large for virtual size) (II) intel(0): Not using default mode "1600x1200" (height too large for virtual size) (II) intel(0): Not using default mode "1600x1200" (height too large for virtual size) (II) intel(0): Not using default mode "1792x1344" (height too large for virtual size) (II) intel(0): Not using default mode "1792x1344" (height too large for virtual size) (II) intel(0): Not using default mode "1856x1392" (height too large for virtual size) (II) intel(0): Not using default mode "1856x1392" (height too large for virtual size) (II) intel(0): Not using default mode "1920x1440" (height too large for virtual size) (II) intel(0): Not using default mode "1920x1440" (height too large for virtual size) (II) intel(0): Not using default mode "832x624" (vrefresh out of range) (II) intel(0): Not using default mode "1152x768" (vrefresh out of range) (II) intel(0): Not using default mode "1400x1050" (height too large for virtual size) (II) intel(0): Not using default mode "1400x1050" (height too large for virtual size) (II) intel(0): Not using default mode "1600x1024" (height too large for virtual size) (II) intel(0): Not using default mode "1920x1440" (height too large for virtual size) (II) intel(0): Not using default mode "2048x1536" (height too large for virtual size) (II) intel(0): Not using default mode "2048x1536" (height too large for virtual size) (II) intel(0): Not using default mode "2048x1536" (height too large for virtual size) (II) intel(0): Printing probed modes for output LVDS (II) intel(0): Modeline "1280x800"x60.2 68.90 1280 1304 1336 1408 800 801 804 813 -hsync -vsync (48.9 kHz) (II) intel(0): Modeline "1024x768"x60.0 65.00 1024 1048 1184 1344 768 771 777 806 -hsync -vsync (48.4 kHz) (II) intel(0): Modeline "800x600"x60.3 40.00 800 840 968 1056 600 601 605 628 +hsync +vsync (37.9 kHz) (II) intel(0): Modeline "640x480"x59.9 25.18 640 656 752 800 480 490 492 525 -hsync -vsync (31.5 kHz) (II) intel(0): Output TV disconnected (II) intel(0): EDID for output TV (II) intel(0): Output VGA disconnected (II) intel(0): Output LVDS connected (II) intel(0): Output TV disconnected (II) intel(0): Output LVDS using initial mode 1280x800 (II) intel(0): Monitoring connected displays enabled (II) intel(0): detected 512 kB GTT. (II) intel(0): detected 7676 kB stolen memory. (==) intel(0): video overlay key set to 0x101fe (==) intel(0): Will not try to enable page flipping (==) intel(0): Triple buffering disabled (==) intel(0): Using gamma correction (1.0, 1.0, 1.0) (==) intel(0): DPI set to (75, 75) (II) Loading sub module "fb" (II) LoadModule: "fb" (II) Loading /usr/lib/xorg/modules//libfb.so (II) Module fb: vendor="X.Org Foundation" compiled for 1.3.0, module version = 1.0.0 ABI class: X.Org ANSI C Emulation, version 0.3 (II) Loading sub module "xaa" (II) LoadModule: "xaa" (II) Loading /usr/lib/xorg/modules//libxaa.so (II) Module xaa: vendor="X.Org Foundation" compiled for 1.3.0, module version = 1.2.0 ABI class: X.Org Video Driver, version 1.2 (II) Loading sub module "ramdac" (II) LoadModule: "ramdac"(II) Module already built-in (II) intel(0): Comparing regs from server start up to After PreInit (==) Depth 24 pixmap format is 32 bpp (II) do I need RAC? No, I don't. (II) resource ranges after preInit: [0] 0 0 0xd0000000 - 0xdfffffff (0x10000000) MS [1] 0 0 0xfc000000 - 0xfc0fffff (0x100000) MS [2] -1 0 0x00100000 - 0x3fffffff (0x3ff00000) MXE(B) [3] -1 0 0x000f0000 - 0x000fffff (0x10000) MX [4] -1 0 0x000c0000 - 0x000effff (0x30000) MX [5] -1 0 0x00000000 - 0x0009ffff (0xa0000) MX [6] -1 0 0xfa000000 - 0xfa000fff (0x1000) MX [7] -1 0 0xf8000000 - 0xf8000fff (0x1000) MX [8] -1 0 0x88000000 - 0x880000ff (0x100) MX [9] -1 0 0xfc404000 - 0xfc4047ff (0x800) MX [10] -1 0 0xfc404c00 - 0xfc404fff (0x400) MX [11] -1 0 0xfc400000 - 0xfc403fff (0x4000) MX [12] -1 0 0xfc404800 - 0xfc404bff (0x400) MX [13] -1 0 0xfc100000 - 0xfc1fffff (0x100000) MX(B) [14] -1 0 0xd0000000 - 0xdfffffff (0x10000000) MX(B) [15] -1 0 0xfc000000 - 0xfc0fffff (0x100000) MX(B) [16] 0 0 0x000a0000 - 0x000affff (0x10000) MS(OprD) [17] 0 0 0x000b0000 - 0x000b7fff (0x8000) MS(OprD) [18] 0 0 0x000b8000 - 0x000bffff (0x8000) MS(OprD) [19] 0 0 0x00001800 - 0x00001807 (0x8) IS [20] -1 0 0x0000ffff - 0x0000ffff (0x1) IX [21] -1 0 0x00000000 - 0x000000ff (0x100) IX [22] -1 0 0x00004000 - 0x000040ff (0x100) IX [23] -1 0 0x00001c20 - 0x00001c3f (0x20) IX [24] -1 0 0x000018e0 - 0x000018ff (0x20) IX [25] -1 0 0x000018d0 - 0x000018d3 (0x4) IX [26] -1 0 0x000018d8 - 0x000018df (0x8) IX [27] -1 0 0x000018d4 - 0x000018d7 (0x4) IX [28] -1 0 0x00001c00 - 0x00001c07 (0x8) IX [29] -1 0 0x00001810 - 0x0000181f (0x10) IX [30] -1 0 0x000001f0 - 0x000001f0 (0x1) IX [31] -1 0 0x000001f0 - 0x000001f7 (0x8) IX [32] -1 0 0x000001f0 - 0x000001f0 (0x1) IX [33] -1 0 0x000001f0 - 0x000001f7 (0x8) IX [34] -1 0 0x000018a0 - 0x000018bf (0x20) IX [35] -1 0 0x00001880 - 0x0000189f (0x20) IX [36] -1 0 0x00001860 - 0x0000187f (0x20) IX [37] -1 0 0x00001840 - 0x0000185f (0x20) IX [38] -1 0 0x00001820 - 0x0000183f (0x20) IX [39] -1 0 0x00001800 - 0x00001807 (0x8) IX(B) [40] 0 0 0x000003b0 - 0x000003bb (0xc) IS(OprU) [41] 0 0 0x000003c0 - 0x000003df (0x20) IS(OprU) (II) intel(0): Kernel reported 488960 total, 1 used (II) intel(0): I830CheckAvailableMemory: 1955836 kB available (==) intel(0): VideoRam: 262144 KB (II) intel(0): Attempting memory allocation with tiled buffers and large DRI memory manager reservation: (II) intel(0): Allocating 4032 scanlines for pixmap cache (II) intel(0): Success. (II) intel(0): Memory allocation layout: (II) intel(0): 0x00000000-0x0001ffff: ring buffer (128 kB) (II) intel(0): 0x00020000-0x00029fff: HW cursors (40 kB) (II) intel(0): 0x0002a000-0x00031fff: logical 3D context (32 kB) (II) intel(0): 0x00040000-0x01a2ffff: front buffer (26560 kB) (II) intel(0): 0x0077f000: end of stolen memory (II) intel(0): 0x01a30000-0x01a3ffff: xaa scratch (64 kB) (II) intel(0): 0x01a40000-0x01e27fff: back buffer (4000 kB) (II) intel(0): 0x01e28000-0x0220ffff: depth buffer (4000 kB) (II) intel(0): 0x02210000-0x0420ffff: textures (32768 kB) (II) intel(0): 0x10000000: end of aperture (II) intel(0): front buffer is not tiled (II) intel(0): back buffer is tiled (II) intel(0): depth buffer is tiled drmOpenDevice: node name is /dev/dri/card0 drmOpenDevice: open result is -1, (No such device) drmOpenDevice: open result is -1, (No such device) drmOpenDevice: Open failed drmOpenDevice: node name is /dev/dri/card0 drmOpenDevice: open result is -1, (No such device) drmOpenDevice: open result is -1, (No such device) drmOpenDevice: Open failed drmOpenByBusid: Searching for BusID pci:0000:00:02.0 drmOpenDevice: node name is /dev/dri/card0 drmOpenDevice: open result is -1, (No such device) drmOpenDevice: open result is -1, (No such device) drmOpenDevice: Open failed drmOpenByBusid: drmOpenMinor returns -19 drmOpenDevice: node name is /dev/dri/card1 drmOpenDevice: open result is -1, (No such device) drmOpenDevice: open result is -1, (No such device) drmOpenDevice: Open failed drmOpenByBusid: drmOpenMinor returns -19 drmOpenDevice: node name is /dev/dri/card2 drmOpenDevice: open result is -1, (No such device) drmOpenDevice: open result is -1, (No such device) drmOpenDevice: Open failed drmOpenByBusid: drmOpenMinor returns -19 drmOpenDevice: node name is /dev/dri/card3 drmOpenDevice: open result is -1, (No such device) drmOpenDevice: open result is -1, (No such device) drmOpenDevice: Open failed drmOpenByBusid: drmOpenMinor returns -19 drmOpenDevice: node name is /dev/dri/card4 drmOpenDevice: open result is -1, (No such device) drmOpenDevice: open result is -1, (No such device) drmOpenDevice: Open failed drmOpenByBusid: drmOpenMinor returns -19 drmOpenDevice: node name is /dev/dri/card5 drmOpenDevice: open result is -1, (No such device) drmOpenDevice: open result is -1, (No such device) drmOpenDevice: Open failed drmOpenByBusid: drmOpenMinor returns -19 drmOpenDevice: node name is /dev/dri/card6 drmOpenDevice: open result is -1, (No such device) drmOpenDevice: open result is -1, (No such device) drmOpenDevice: Open failed drmOpenByBusid: drmOpenMinor returns -19 drmOpenDevice: node name is /dev/dri/card7 drmOpenDevice: open result is -1, (No such device) drmOpenDevice: open result is -1, (No such device) drmOpenDevice: Open failed drmOpenByBusid: drmOpenMinor returns -19 drmOpenDevice: node name is /dev/dri/card8 drmOpenDevice: open result is -1, (No such device) drmOpenDevice: open result is -1, (No such device) drmOpenDevice: Open failed drmOpenByBusid: drmOpenMinor returns -19 drmOpenDevice: node name is /dev/dri/card9 drmOpenDevice: open result is -1, (No such device) drmOpenDevice: open result is -1, (No such device) drmOpenDevice: Open failed drmOpenByBusid: drmOpenMinor returns -19 drmOpenDevice: node name is /dev/dri/card10 drmOpenDevice: open result is -1, (No such device) drmOpenDevice: open result is -1, (No such device) drmOpenDevice: Open failed drmOpenByBusid: drmOpenMinor returns -19 drmOpenDevice: node name is /dev/dri/card11 drmOpenDevice: open result is -1, (No such device) drmOpenDevice: open result is -1, (No such device) drmOpenDevice: Open failed drmOpenByBusid: drmOpenMinor returns -19 drmOpenDevice: node name is /dev/dri/card12 drmOpenDevice: open result is -1, (No such device) drmOpenDevice: open result is -1, (No such device) drmOpenDevice: Open failed drmOpenByBusid: drmOpenMinor returns -19 drmOpenDevice: node name is /dev/dri/card13 drmOpenDevice: open result is -1, (No such device) drmOpenDevice: open result is -1, (No such device) drmOpenDevice: Open failed drmOpenByBusid: drmOpenMinor returns -19 drmOpenDevice: node name is /dev/dri/card14 drmOpenDevice: open result is -1, (No such device) drmOpenDevice: open result is -1, (No such device) drmOpenDevice: Open failed drmOpenByBusid: drmOpenMinor returns -19 drmOpenDevice: node name is /dev/dri/card0 drmOpenDevice: open result is -1, (No such device) drmOpenDevice: open result is -1, (No such device) drmOpenDevice: Open failed drmOpenDevice: node name is /dev/dri/card0 drmOpenDevice: open result is -1, (No such device) drmOpenDevice: open result is -1, (No such device) drmOpenDevice: Open failed drmOpenDevice: node name is /dev/dri/card1 drmOpenDevice: open result is -1, (No such device) drmOpenDevice: open result is -1, (No such device) drmOpenDevice: Open failed drmOpenDevice: node name is /dev/dri/card2 drmOpenDevice: open result is -1, (No such device) drmOpenDevice: open result is -1, (No such device) drmOpenDevice: Open failed drmOpenDevice: node name is /dev/dri/card3 drmOpenDevice: open result is -1, (No such device) drmOpenDevice: open result is -1, (No such device) drmOpenDevice: Open failed drmOpenDevice: node name is /dev/dri/card4 drmOpenDevice: open result is -1, (No such device) drmOpenDevice: open result is -1, (No such device) drmOpenDevice: Open failed drmOpenDevice: node name is /dev/dri/card5 drmOpenDevice: open result is -1, (No such device) drmOpenDevice: open result is -1, (No such device) drmOpenDevice: Open failed drmOpenDevice: node name is /dev/dri/card6 drmOpenDevice: open result is -1, (No such device) drmOpenDevice: open result is -1, (No such device) drmOpenDevice: Open failed drmOpenDevice: node name is /dev/dri/card7 drmOpenDevice: open result is -1, (No such device) drmOpenDevice: open result is -1, (No such device) drmOpenDevice: Open failed drmOpenDevice: node name is /dev/dri/card8 drmOpenDevice: open result is -1, (No such device) drmOpenDevice: open result is -1, (No such device) drmOpenDevice: Open failed drmOpenDevice: node name is /dev/dri/card9 drmOpenDevice: open result is -1, (No such device) drmOpenDevice: open result is -1, (No such device) drmOpenDevice: Open failed drmOpenDevice: node name is /dev/dri/card10 drmOpenDevice: open result is -1, (No such device) drmOpenDevice: open result is -1, (No such device) drmOpenDevice: Open failed drmOpenDevice: node name is /dev/dri/card11 drmOpenDevice: open result is -1, (No such device) drmOpenDevice: open result is -1, (No such device) drmOpenDevice: Open failed drmOpenDevice: node name is /dev/dri/card12 drmOpenDevice: open result is -1, (No such device) drmOpenDevice: open result is -1, (No such device) drmOpenDevice: Open failed drmOpenDevice: node name is /dev/dri/card13 drmOpenDevice: open result is -1, (No such device) drmOpenDevice: open result is -1, (No such device) drmOpenDevice: Open failed drmOpenDevice: node name is /dev/dri/card14 drmOpenDevice: open result is -1, (No such device) drmOpenDevice: open result is -1, (No such device) drmOpenDevice: Open failed (II) intel(0): [drm] drmOpen failed (EE) intel(0): [dri] DRIScreenInit failed. Disabling DRI. (II) intel(0): Page Flipping disabled (==) intel(0): Write-combining range (0xd0000000,0x10000000) (II) intel(0): vgaHWGetIOBase: hwp->IOBase is 0x03d0, hwp->PIOOffset is 0x0000 (II) intel(0): Using XFree86 Acceleration Architecture (XAA) Screen to screen bit blits Solid filled rectangles 8x8 mono pattern filled rectangles Indirect CPU to Screen color expansion Solid Horizontal and Vertical Lines Offscreen Pixmaps Setting up tile and stipple cache: 32 128x128 slots 29 256x256 slots 10 512x512 slots (==) intel(0): Backing store disabled (==) intel(0): Silken mouse enabled (II) intel(0): Initializing HW Cursor (II) intel(0): xf86BindGARTMemory: bind key 0 at 0x0077f000 (pgoffset 1919) (II) intel(0): xf86BindGARTMemory: bind key 1 at 0x01a30000 (pgoffset 6704) (WW) intel(0): ESR is 0x00000010, page table error (WW) intel(0): PGTBL_ER is 0x00000010, display A pte (WW) intel(0): Existing errors found in hardware state. (II) intel(0): Output configuration: (II) intel(0): Pipe A is off (II) intel(0): Display plane A is now disabled and connected to pipe A. (II) intel(0): Pipe B is on (II) intel(0): Display plane B is now enabled and connected to pipe B. (II) intel(0): Output VGA is connected to pipe none (II) intel(0): Output LVDS is connected to pipe B (II) intel(0): Output TV is connected to pipe none (II) intel(0): Set up textured video (II) intel(0): direct rendering: Failed (II) intel(0): RandR 1.2 enabled, ignore the following RandR disabled message. (--) RandR disabled (II) Initializing built-in extension MIT-SHM (II) Initializing built-in extension XInputExtension (II) Initializing built-in extension XTEST (II) Initializing built-in extension XKEYBOARD (II) Initializing built-in extension XC-APPGROUP (II) Initializing built-in extension XAccessControlExtension (II) Initializing built-in extension SECURITY (II) Initializing built-in extension XINERAMA (II) Initializing built-in extension XFIXES (II) Initializing built-in extension XFree86-Bigfont (II) Initializing built-in extension RENDER (II) Initializing built-in extension RANDR (II) Initializing built-in extension COMPOSITE (II) Initializing built-in extension DAMAGE (II) Initializing built-in extension XEVIE (EE) AIGLX: Screen 0 is not DRI capable (II) Loading local sub module "GLcore" (II) LoadModule: "GLcore" (II) Loading /usr/lib/xorg/modules/extensions//libGLcore.so (II) Module GLcore: vendor="X.Org Foundation" compiled for 1.3.0, module version = 1.0.0 ABI class: X.Org Server Extension, version 0.3 (II) GLX: Initialized MESA-PROXY GL provider for screen 0 (II) intel(0): Setting screen physical size to 331 x 207 (**) Option "Protocol" "Auto" (**) Mouse1: Device: "/dev/input/mice" (**) Mouse1: Protocol: "Auto" (**) Option "CorePointer" (**) Mouse1: Core Pointer (**) Option "Device" "/dev/input/mice" (==) Mouse1: Emulate3Buttons, Emulate3Timeout: 50 (**) Option "ZAxisMapping" "4 5 6 7" (**) Mouse1: ZAxisMapping: buttons 4, 5, 6 and 7 (**) Mouse1: Buttons: 11 (**) Option "CoreKeyboard" (**) Keyboard1: Core Keyboard (**) Option "Protocol" "standard" (**) Keyboard1: Protocol: standard (**) Option "AutoRepeat" "500 30" (**) Option "XkbRules" "xorg" (**) Keyboard1: XkbRules: "xorg" (**) Option "XkbModel" "pc105" (**) Keyboard1: XkbModel: "pc105" (**) Option "XkbLayout" "us" (**) Keyboard1: XkbLayout: "us" (**) Option "CustomKeycodes" "off" (**) Keyboard1: CustomKeycodes disabled (II) XINPUT: Adding extended input device "Keyboard1" (type: KEYBOARD) (II) XINPUT: Adding extended input device "Mouse1" (type: MOUSE) (--) Mouse1: PnP-detected protocol: "ExplorerPS/2" (II) Mouse1: ps2EnableDataReporting: succeeded (II) intel(0): Output VGA disconnected (II) intel(0): EDID for output VGA (II) intel(0): Output LVDS connected (II) intel(0): I2C device "LVDSDDC_C:ddc2" registered at address 0xA0. (II) intel(0): I2C device "LVDSDDC_C:ddc2" removed. (II) intel(0): EDID for output LVDS (II) intel(0): Manufacturer: CPT Model: 1415 Serial#: 0 (II) intel(0): Year: 2007 Week: 34 (II) intel(0): EDID Version: 1.3 (II) intel(0): Digital Display Input (II) intel(0): Max H-Image Size [cm]: horiz.: 33 vert.: 21 (II) intel(0): Gamma: 2.20 (II) intel(0): No DPMS capabilities specified; RGB/Color Display (II) intel(0): First detailed timing is preferred mode (II) intel(0): redX: 0.613 redY: 0.336 greenX: 0.311 greenY: 0.563 (II) intel(0): blueX: 0.152 blueY: 0.131 whiteX: 0.315 whiteY: 0.329 (II) intel(0): Manufacturer's mask: 0 (II) intel(0): Supported additional Video Mode: (II) intel(0): clock: 68.9 MHz Image Size: 331 x 207 mm (II) intel(0): h_active: 1280 h_sync: 1304 h_sync_end 1336 h_blank_end 1408 h_border: 0 (II) intel(0): v_active: 800 v_sync: 801 v_sync_end 804 v_blanking: 813 v_border: 0 (II) intel(0): CPT (II) intel(0): CLAA154WB05A (II) intel(0): EDID (in hex): (II) intel(0): 00ffffffffffff000e14151400000000 (II) intel(0): 22110103802115780a092d9d564f9027 (II) intel(0): 21505400000001010101010101010101 (II) intel(0): 010101010101ea1a008050200d301820 (II) intel(0): 13004bcf100000190000000f00202020 (II) intel(0): 2020202020206e050f00000000fe0043 (II) intel(0): 50540a202020202020202020000000fe (II) intel(0): 00434c414131353457423035412000c1 (II) intel(0): Printing DDC gathered Modelines: (II) intel(0): Modeline "1280x800" 68.90 1280 1304 1336 1408 800 801 804 813 -hsync -vsync (II) intel(0): EDID vendor "CPT", prod id 5141 (II) intel(0): Not using default mode "640x350" (vrefresh out of range) (II) intel(0): Not using default mode "640x400" (vrefresh out of range) (II) intel(0): Not using default mode "720x400" (vrefresh out of range) (II) intel(0): Not using default mode "640x480" (vrefresh out of range) (II) intel(0): Not using default mode "640x480" (vrefresh out of range) (II) intel(0): Not using default mode "640x480" (vrefresh out of range) (II) intel(0): Not using default mode "800x600" (vrefresh out of range) (II) intel(0): Not using default mode "800x600" (vrefresh out of range) (II) intel(0): Not using default mode "800x600" (vrefresh out of range) (II) intel(0): Not using default mode "800x600" (vrefresh out of range) (II) intel(0): Not using default mode "1024x768" (vrefresh out of range) (II) intel(0): Not using default mode "1024x768" (vrefresh out of range) (II) intel(0): Not using default mode "1024x768" (vrefresh out of range) (II) intel(0): Not using default mode "1152x864" (height too large for virtual size) (II) intel(0): Not using default mode "1280x960" (height too large for virtual size) (II) intel(0): Not using default mode "1280x960" (height too large for virtual size) (II) intel(0): Not using default mode "1280x1024" (height too large for virtual size) (II) intel(0): Not using default mode "1280x1024" (height too large for virtual size) (II) intel(0): Not using default mode "1280x1024" (height too large for virtual size) (II) intel(0): Not using default mode "1600x1200" (height too large for virtual size) (II) intel(0): Not using default mode "1600x1200" (height too large for virtual size) (II) intel(0): Not using default mode "1600x1200" (height too large for virtual size) (II) intel(0): Not using default mode "1600x1200" (height too large for virtual size) (II) intel(0): Not using default mode "1600x1200" (height too large for virtual size) (II) intel(0): Not using default mode "1792x1344" (height too large for virtual size) (II) intel(0): Not using default mode "1792x1344" (height too large for virtual size) (II) intel(0): Not using default mode "1856x1392" (height too large for virtual size) (II) intel(0): Not using default mode "1856x1392" (height too large for virtual size) (II) intel(0): Not using default mode "1920x1440" (height too large for virtual size) (II) intel(0): Not using default mode "1920x1440" (height too large for virtual size) (II) intel(0): Not using default mode "832x624" (vrefresh out of range) (II) intel(0): Not using default mode "1152x768" (vrefresh out of range) (II) intel(0): Not using default mode "1400x1050" (height too large for virtual size) (II) intel(0): Not using default mode "1400x1050" (height too large for virtual size) (II) intel(0): Not using default mode "1600x1024" (height too large for virtual size) (II) intel(0): Not using default mode "1920x1440" (height too large for virtual size) (II) intel(0): Not using default mode "2048x1536" (height too large for virtual size) (II) intel(0): Not using default mode "2048x1536" (height too large for virtual size) (II) intel(0): Not using default mode "2048x1536" (height too large for virtual size) (II) intel(0): Printing probed modes for output LVDS (II) intel(0): Modeline "1280x800"x60.2 68.90 1280 1304 1336 1408 800 801 804 813 -hsync -vsync (48.9 kHz) (II) intel(0): Modeline "1024x768"x60.0 65.00 1024 1048 1184 1344 768 771 777 806 -hsync -vsync (48.4 kHz) (II) intel(0): Modeline "800x600"x60.3 40.00 800 840 968 1056 600 601 605 628 +hsync +vsync (37.9 kHz) (II) intel(0): Modeline "640x480"x59.9 25.18 640 656 752 800 480 490 492 525 -hsync -vsync (31.5 kHz) (II) intel(0): Output TV disconnected (II) intel(0): EDID for output TV (II) intel(0): Output VGA disconnected (II) intel(0): EDID for output VGA (II) intel(0): Output LVDS connected (II) intel(0): I2C device "LVDSDDC_C:ddc2" registered at address 0xA0. (II) intel(0): I2C device "LVDSDDC_C:ddc2" removed. (II) intel(0): EDID for output LVDS (II) intel(0): Manufacturer: CPT Model: 1415 Serial#: 0 (II) intel(0): Year: 2007 Week: 34 (II) intel(0): EDID Version: 1.3 (II) intel(0): Digital Display Input (II) intel(0): Max H-Image Size [cm]: horiz.: 33 vert.: 21 (II) intel(0): Gamma: 2.20 (II) intel(0): No DPMS capabilities specified; RGB/Color Display (II) intel(0): First detailed timing is preferred mode (II) intel(0): redX: 0.613 redY: 0.336 greenX: 0.311 greenY: 0.563 (II) intel(0): blueX: 0.152 blueY: 0.131 whiteX: 0.315 whiteY: 0.329 (II) intel(0): Manufacturer's mask: 0 (II) intel(0): Supported additional Video Mode: (II) intel(0): clock: 68.9 MHz Image Size: 331 x 207 mm (II) intel(0): h_active: 1280 h_sync: 1304 h_sync_end 1336 h_blank_end 1408 h_border: 0 (II) intel(0): v_active: 800 v_sync: 801 v_sync_end 804 v_blanking: 813 v_border: 0 (II) intel(0): CPT (II) intel(0): CLAA154WB05A (II) intel(0): EDID (in hex): (II) intel(0): 00ffffffffffff000e14151400000000 (II) intel(0): 22110103802115780a092d9d564f9027 (II) intel(0): 21505400000001010101010101010101 (II) intel(0): 010101010101ea1a008050200d301820 (II) intel(0): 13004bcf100000190000000f00202020 (II) intel(0): 2020202020206e050f00000000fe0043 (II) intel(0): 50540a202020202020202020000000fe (II) intel(0): 00434c414131353457423035412000c1 (II) intel(0): Printing DDC gathered Modelines: (II) intel(0): Modeline "1280x800" 68.90 1280 1304 1336 1408 800 801 804 813 -hsync -vsync (II) intel(0): EDID vendor "CPT", prod id 5141 (II) intel(0): Not using default mode "640x350" (vrefresh out of range) (II) intel(0): Not using default mode "640x400" (vrefresh out of range) (II) intel(0): Not using default mode "720x400" (vrefresh out of range) (II) intel(0): Not using default mode "640x480" (vrefresh out of range) (II) intel(0): Not using default mode "640x480" (vrefresh out of range) (II) intel(0): Not using default mode "640x480" (vrefresh out of range) (II) intel(0): Not using default mode "800x600" (vrefresh out of range) (II) intel(0): Not using default mode "800x600" (vrefresh out of range) (II) intel(0): Not using default mode "800x600" (vrefresh out of range) (II) intel(0): Not using default mode "800x600" (vrefresh out of range) (II) intel(0): Not using default mode "1024x768" (vrefresh out of range) (II) intel(0): Not using default mode "1024x768" (vrefresh out of range) (II) intel(0): Not using default mode "1024x768" (vrefresh out of range) (II) intel(0): Not using default mode "1152x864" (height too large for virtual size) (II) intel(0): Not using default mode "1280x960" (height too large for virtual size) (II) intel(0): Not using default mode "1280x960" (height too large for virtual size) (II) intel(0): Not using default mode "1280x1024" (height too large for virtual size) (II) intel(0): Not using default mode "1280x1024" (height too large for virtual size) (II) intel(0): Not using default mode "1280x1024" (height too large for virtual size) (II) intel(0): Not using default mode "1600x1200" (height too large for virtual size) (II) intel(0): Not using default mode "1600x1200" (height too large for virtual size) (II) intel(0): Not using default mode "1600x1200" (height too large for virtual size) (II) intel(0): Not using default mode "1600x1200" (height too large for virtual size) (II) intel(0): Not using default mode "1600x1200" (height too large for virtual size) (II) intel(0): Not using default mode "1792x1344" (height too large for virtual size) (II) intel(0): Not using default mode "1792x1344" (height too large for virtual size) (II) intel(0): Not using default mode "1856x1392" (height too large for virtual size) (II) intel(0): Not using default mode "1856x1392" (height too large for virtual size) (II) intel(0): Not using default mode "1920x1440" (height too large for virtual size) (II) intel(0): Not using default mode "1920x1440" (height too large for virtual size) (II) intel(0): Not using default mode "832x624" (vrefresh out of range) (II) intel(0): Not using default mode "1152x768" (vrefresh out of range) (II) intel(0): Not using default mode "1400x1050" (height too large for virtual size) (II) intel(0): Not using default mode "1400x1050" (height too large for virtual size) (II) intel(0): Not using default mode "1600x1024" (height too large for virtual size) (II) intel(0): Not using default mode "1920x1440" (height too large for virtual size) (II) intel(0): Not using default mode "2048x1536" (height too large for virtual size) (II) intel(0): Not using default mode "2048x1536" (height too large for virtual size) (II) intel(0): Not using default mode "2048x1536" (height too large for virtual size) (II) intel(0): Printing probed modes for output LVDS (II) intel(0): Modeline "1280x800"x60.2 68.90 1280 1304 1336 1408 800 801 804 813 -hsync -vsync (48.9 kHz) (II) intel(0): Modeline "1024x768"x60.0 65.00 1024 1048 1184 1344 768 771 777 806 -hsync -vsync (48.4 kHz) (II) intel(0): Modeline "800x600"x60.3 40.00 800 840 968 1056 600 601 605 628 +hsync +vsync (37.9 kHz) (II) intel(0): Modeline "640x480"x59.9 25.18 640 656 752 800 480 490 492 525 -hsync -vsync (31.5 kHz) (II) intel(0): Output TV disconnected (II) intel(0): EDID for output TV (II) intel(0): xf86UnbindGARTMemory: unbind key 0 (II) intel(0): xf86UnbindGARTMemory: unbind key 1 FreeFontPath: FPE "/usr/share/fonts/misc" refcount is 2, should be 1; fixing.

xorg.conf

Код:

# File generated by xorgconfig. # # Copyright 2004 The X.Org Foundation # # Permission is hereby granted, free of charge, to any person obtaining a # copy of this software and associated documentation files (the "Software"), # to deal in the Software without restriction, including without limitation # the rights to use, copy, modify, merge, publish, distribute, sublicense, # and/or sell copies of the Software, and to permit persons to whom the # Software is furnished to do so, subject to the following conditions: # # The above copyright notice and this permission notice shall be included in # all copies or substantial portions of the Software. # # THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND, EXPRESS OR # IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES OF MERCHANTABILITY, # FITNESS FOR A PARTICULAR PURPOSE AND NONINFRINGEMENT. IN NO EVENT SHALL # The X.Org Foundation BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER LIABILITY, # WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING FROM, OUT OF # OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR OTHER DEALINGS IN THE # SOFTWARE. # # Except as contained in this notice, the name of The X.Org Foundation shall # not be used in advertising or otherwise to promote the sale, use or other # dealings in this Software without prior written authorization from # The X.Org Foundation. # # ********************************************************************** # Refer to the xorg.conf(5x) man page for details about the format of # this file. # ********************************************************************** # ********************************************************************** # Module section -- this section is used to specify # which dynamically loadable modules to load. # ********************************************************************** # Section "Module" # This loads the DBE extension module. Load "dbe" # Double buffer extension # This loads the miscellaneous extensions module, and disables # initialisation of the XFree86-DGA extension within that module. SubSection "extmod" Option "omit xfree86-dga" # don't initialise the DGA extension EndSubSection # This loads the font modules # Load "type1" Load "freetype" # Load "xtt" # This loads the GLX module Load "glx" # This loads the DRI module Load "dri" EndSection # ********************************************************************** # Files section. This allows default font and rgb paths to be set # ********************************************************************** Section "Files" # The location of the RGB database. Note, this is the name of the # file minus the extension (like ".txt" or ".db"). There is normally # no need to change the default. # RgbPath "/usr/share/X11/rgb" # Multiple FontPath entries are allowed (which are concatenated together), # as well as specifying multiple comma-separated entries in one FontPath # command (or a combination of both methods) # # FontPath "/usr/share/fonts/TTF" FontPath "/usr/share/fonts/OTF" FontPath "/usr/share/fonts/Type1" FontPath "/usr/share/fonts/misc" FontPath "/usr/share/fonts/75dpi/:unscaled" # FontPath "/usr/lib/X11/fonts/local/" FontPath "/usr/lib/X11/fonts/misc/" FontPath "/usr/lib/X11/fonts/75dpi/:unscaled" FontPath "/usr/lib/X11/fonts/100dpi/:unscaled" FontPath "/usr/lib/X11/fonts/Speedo/" FontPath "/usr/lib/X11/fonts/Type1/" FontPath "/usr/lib/X11/fonts/TTF/" FontPath "/usr/lib/X11/fonts/OTF/" FontPath "/usr/lib/X11/fonts/cyrillic/" FontPath "/usr/lib/X11/fonts/75dpi/" FontPath "/usr/lib/X11/fonts/100dpi/" # The module search path. The default path is shown here. # ModulePath "/usr/lib/xorg/modules" EndSection # ********************************************************************** # Server flags section. # ********************************************************************** Section "ServerFlags" # Uncomment this to cause a core dump at the spot where a signal is # received. This may leave the console in an unusable state, but may # provide a better stack trace in the core dump to aid in debugging # Option "NoTrapSignals" # Uncomment this to disable the <Ctrl><Alt><Fn> VT switch sequence # (where n is 1 through 12). This allows clients to receive these key # events. # Option "DontVTSwitch" # Uncomment this to disable the <Ctrl><Alt><BS> server abort sequence # This allows clients to receive this key event. # Option "DontZap" # Uncomment this to disable the <Ctrl><Alt><KP_+>/<KP_-> mode switching # sequences. This allows clients to receive these key events. # Option "Dont Zoom" # Uncomment this to disable tuning with the xvidtune client. With # it the client can still run and fetch card and monitor attributes, # but it will not be allowed to change them. If it tries it will # receive a protocol error. # Option "DisableVidModeExtension" # Uncomment this to enable the use of a non-local xvidtune client. # Option "AllowNonLocalXvidtune" # Uncomment this to disable dynamically modifying the input device # (mouse and keyboard) settings. # Option "DisableModInDev" # Uncomment this to enable the use of a non-local client to # change the keyboard or mouse settings (currently only xset). # Option "AllowNonLocalModInDev" EndSection # ********************************************************************** # Input devices # ********************************************************************** # ********************************************************************** # Core keyboard's InputDevice section # ********************************************************************** Section "InputDevice" Identifier "Keyboard1" Driver "kbd" # For most OSs the protocol can be omitted (it defaults to "Standard"). # When using XQUEUE (only for SVR3 and SVR4, but not Solaris), # uncomment the following line. # Option "Protocol" "Xqueue" Option "AutoRepeat" "500 30" # Specify which keyboard LEDs can be user-controlled (eg, with xset(1)) # Option "Xleds" "1 2 3" # Option "LeftAlt" "Meta" # Option "RightAlt" "ModeShift" # To customise the XKB settings to suit your keyboard, modify the # lines below (which are the defaults). For example, for a non-U.S. # keyboard, you will probably want to use: # Option "XkbModel" "pc105" # If you have a US Microsoft Natural keyboard, you can use: # Option "XkbModel" "microsoft" # # Then to change the language, change the Layout setting. # For example, a german layout can be obtained with: # Option "XkbLayout" "de" # or: # Option "XkbLayout" "de" # Option "XkbVariant" "nodeadkeys" # # If you'd like to switch the positions of your capslock and # control keys, use: # Option "XkbOptions" "ctrl:swapcaps" # These are the default XKB settings for Xorg # Option "XkbRules" "xorg" # Option "XkbModel" "pc105" # Option "XkbLayout" "us" # Option "XkbVariant" "" # Option "XkbOptions" "" # Option "XkbDisable" Option "XkbRules" "xorg" Option "XkbModel" "pc105" Option "XkbLayout" "us" EndSection # ********************************************************************** # Core Pointer's InputDevice section # ********************************************************************** Section "InputDevice" # Identifier and driver Identifier "Mouse1" Driver "mouse" Option "Protocol" "Auto" # Auto detect Option "Device" "/dev/input/mice" # When using XQUEUE, comment out the above two lines, and uncomment # the following line. # Option "Protocol" "Xqueue" # Mouse-speed setting for PS/2 mouse. # Option "Resolution" "256" # Baudrate and SampleRate are only for some Logitech mice. In # almost every case these lines should be omitted. # Option "BaudRate" "9600" # Option "SampleRate" "150" # Mouse wheel mapping. Default is to map vertical wheel to buttons 4 & 5, # horizontal wheel to buttons 6 & 7. Change if your mouse has more than # 3 buttons and you need to map the wheel to different button ids to avoid # conflicts. Option "ZAxisMapping" "4 5 6 7" # Emulate3Buttons is an option for 2-button mice # Emulate3Timeout is the timeout in milliseconds (default is 50ms) # Option "Emulate3Buttons" # Option "Emulate3Timeout" "50" # ChordMiddle is an option for some 3-button Logitech mice # Option "ChordMiddle" EndSection # ********************************************************************** # Other input device sections # this is optional and is required only if you # are using extended input devices. This is for example only. Refer # to the xorg.conf man page for a description of the options. # ********************************************************************** # # Section "InputDevice" # Identifier "Mouse2" # Driver "mouse" # Option "Protocol" "MouseMan" # Option "Device" "/dev/mouse2" # EndSection # # Section "InputDevice" # Identifier "spaceball" # Driver "magellan" # Option "Device" "/dev/cua0" # EndSection # # Section "InputDevice" # Identifier "spaceball2" # Driver "spaceorb" # Option "Device" "/dev/cua0" # EndSection # # Section "InputDevice" # Identifier "touchscreen0" # Driver "microtouch" # Option "Device" "/dev/ttyS0" # Option "MinX" "1412" # Option "MaxX" "15184" # Option "MinY" "15372" # Option "MaxY" "1230" # Option "ScreenNumber" "0" # Option "ReportingMode" "Scaled" # Option "ButtonNumber" "1" # Option "SendCoreEvents" # EndSection # # Section "InputDevice" # Identifier "touchscreen1" # Driver "elo2300" # Option "Device" "/dev/ttyS0" # Option "MinX" "231" # Option "MaxX" "3868" # Option "MinY" "3858" # Option "MaxY" "272" # Option "ScreenNumber" "0" # Option "ReportingMode" "Scaled" # Option "ButtonThreshold" "17" # Option "ButtonNumber" "1" # Option "SendCoreEvents" # EndSection # ********************************************************************** # Monitor section # ********************************************************************** # Any number of monitor sections may be present Section "Monitor" Identifier "My Monitor" # HorizSync is in kHz unless units are specified. # HorizSync may be a comma separated list of discrete values, or a # comma separated list of ranges of values. # NOTE: THE VALUES HERE ARE EXAMPLES ONLY. REFER TO YOUR MONITOR'S # USER MANUAL FOR THE CORRECT NUMBERS. HorizSync 31.5 # HorizSync 30-64 # multisync # HorizSync 31.5, 35.2 # multiple fixed sync frequencies # HorizSync 15-25, 30-50 # multiple ranges of sync frequencies # VertRefresh is in Hz unless units are specified. # VertRefresh may be a comma separated list of discrete values, or a # comma separated list of ranges of values. # NOTE: THE VALUES HERE ARE EXAMPLES ONLY. REFER TO YOUR MONITOR'S # USER MANUAL FOR THE CORRECT NUMBERS. VertRefresh 50-70 EndSection # ********************************************************************** # Graphics device section # ********************************************************************** # Any number of graphics device sections may be present # Standard VGA Device: Section "Device" Identifier "Standard VGA" VendorName "Unknown" BoardName "Unknown" # The chipset line is optional in most cases. It can be used to override # the driver's chipset detection, and should not normally be specified. # Chipset "generic" # The Driver line must be present. When using run-time loadable driver # modules, this line instructs the server to load the specified driver # module. Even when not using loadable driver modules, this line # indicates which driver should interpret the information in this section. Driver "vga" # The BusID line is used to specify which of possibly multiple devices # this section is intended for. When this line isn't present, a device # section can only match up with the primary video device. For PCI # devices a line like the following could be used. This line should not # normally be included unless there is more than one video device # intalled. # BusID "PCI:0:10:0" # VideoRam 256 # Clocks 25.2 28.3 EndSection # Device configured by xorgconfig: Section "Device" Identifier "** Intel i810 (generic) [i810]" Driver "i810" #VideoRam 262144 # Insert Clocks lines here if appropriate EndSection # ********************************************************************** # Screen sections # ********************************************************************** # Any number of screen sections may be present. Each describes # the configuration of a single screen. A single specific screen section # may be specified from the X server command line with the "-screen" # option. Section "Screen" Identifier "Screen 1" Device "** Intel i810 (generic) [i810]" Monitor "My Monitor" DefaultDepth 24 Subsection "Display" Depth 8 Modes "1280x1024" "1024x768" "800x600" "640x480" ViewPort 0 0 Virtual 1600 1280 EndSubsection Subsection "Display" Depth 16 Modes "1280x1024" "1024x768" "800x600" "640x480" ViewPort 0 0 Virtual 1280 1024 EndSubsection Subsection "Display" Depth 24 Modes "1280x1024" ViewPort 0 0 Virtual 1280 800 EndSubsection EndSection # ********************************************************************** # ServerLayout sections. # ********************************************************************** # Any number of ServerLayout sections may be present. Each describes # the way multiple screens are organised. A specific ServerLayout # section may be specified from the X server command line with the # "-layout" option. In the absence of this, the first section is used. # When now ServerLayout section is present, the first Screen section # is used alone. Section "ServerLayout" # The Identifier line must be present Identifier "Simple Layout" # Each Screen line specifies a Screen section name, and optionally # the relative position of other screens. The four names after # primary screen name are the screens to the top, bottom, left and right # of the primary screen. In this example, screen 2 is located to the # right of screen 1. Screen "Screen 1" # Each InputDevice line specifies an InputDevice section name and # optionally some options to specify the way the device is to be # used. Those options include "CorePointer", "CoreKeyboard" and # "SendCoreEvents". InputDevice "Mouse1" "CorePointer" InputDevice "Keyboard1" "CoreKeyboard" EndSection Section "DRI" Mode 0666 EndSection

[ptolemy]

Ждущий и спящий режим на лаптопеУ меня на лаптопе (Tosiba Satellite-5005, Mandriva Powepack-2008/GNOME ) не работает спящий и ждущий режимы,

У меня ни на одном из трех ноутбуков, ни с одним из перечисленных в профиле дистрибутивов это нормально не работало. Сохранение в RAM - вообще не пашет, сохранение на диск - работает ненадежно. Похоже, что ядро виновато. Нужно ждать видимо.

[Ariel]

У меня ни на одном из трех ноутбуков, ни с одним из перечисленных в профиле дистрибутивов это нормально не работало. Сохранение в RAM - вообще не пашет, сохранение на диск - работает ненадежно. Похоже, что ядро виновато. Нужно ждать видимо.

Лучше не использовать klaptop и прочую нечисть, пишите скрипты в /etc/acpi/
will work!

экзамплов в Сети много

[dakar]

Лучше не использовать klaptop и прочую нечисть, пишите скрипты в /etc/acpi/
will work!

экзамплов в Сети много

Ну если знаешь, напиши пример или дай ссылку. Те че жалко? Не все ж спецы в этом. Я сам на линух только месяц как с форточек пересел.

[BountyAdler]

колеблюсь между конфигурацией на базе амд (турион х2 2,1ггц) с двумя гигами оперативы и интелом меньшей частоты (двойная дуо кора 1,8 ггц) с гигом оперативы.

кто из них предпочтительнее с точки зрения работы с базами данных? ну и какие мысли про фотошоп скажете.
ну и в плане работы с Линухом...

прост реально разброс цен приличный, а с деньгами напряг

[sensei]

колеблюсь между конфигурацией на базе амд (турион х2 2,1ггц) с двумя гигами оперативы и интелом меньшей частоты (двойная дуо кора 1,8 ггц) с гигом оперативы.

кто из них предпочтительнее с точки зрения работы с базами данных? ну и какие мысли про фотошоп скажете.
ну и в плане работы с Линухом...

прост реально разброс цен приличный, а с деньгами напряг

Коре дуо с частотой 1.8 точно взувает АМД с 2.1 (сечас кстати на частоту вобще нету смысла смотреть), на ноут с гигом можно доставить еще одну планку и будет тоже два

З.Ы. Интел на ноутах рулит