[Решено]Ошибка при загрузке bug int 14 (При загрузке выдаётся ошибка bug int 14)

[Grenka]

Здравствуйте.
Уговорил брата на Ubuntu. Поставили ему 9.04 ядро 2.6.28-11. После установки обновили до 2.6.28-15. Теперь проявляется следующий глюк: не каждый раз, но довольно часто после меню Grub появляется чёрный экран с сообщением об ошибке bug int 14... (см приложенный скриншот).
Поиск в google дал следующий результат http://ubuntuforums.org/showthread.php?p=7153507
Насколько я понимаю это не решение. У меня ядро 2.6.28-15 работает без проблем.

Есть предположение, почему у брата может проявляться этот глюк. У него процессор AMD Athlon 64X2 4400+, судя по описанию 64 битный. А Ubuntu я ему советовал скачивать и ставить 32 битную. Может это и приводит к сбою? Вот тут товарищ говорит, что поставил 64 битную версию системы и нет проблем. Но это всего лишь одно высказывание.

Буду рад услышать ваше мнение по поводу предположения и ошибки в целом.

Заранее спасибо.
Всего доброго.

[anarhst]

Могу ошибаться, но все же покажите /boot/grub/menu.lst

[Grenka]

Могу ошибаться, но все же покажите /boot/grub/menu.lst

default установлено равным 2, что бы загружалось ядро Ubuntu 9.04, kernel 2.6.28-11-generic. Смотрели как работает с более старым ядром. Разницы нет. Оба 2.6.28-11 и 2.6.28-15 выдают вышеназванную ошибку.

Код: Выделить всё

# menu.lst - See: grub(8), info grub, update-grub(8)
#            grub-install(8), grub-floppy(8),
#            grub-md5-crypt, /usr/share/doc/grub
#            and /usr/share/doc/grub-doc/.

## default num
# Set the default entry to the entry number NUM. Numbering starts from 0, and
# the entry number 0 is the default if the command is not used.
#
# You can specify 'saved' instead of a number. In this case, the default entry
# is the entry saved with the command 'savedefault'.
# WARNING: If you are using dmraid do not use 'savedefault' or your
# array will desync and will not let you boot your system.
default        2

## timeout sec
# Set a timeout, in SEC seconds, before automatically booting the default entry
# (normally the first entry defined).
timeout        2

## hiddenmenu
# Hides the menu by default (press ESC to see the menu)
#hiddenmenu

# Pretty colours
#color cyan/blue white/blue

## password ['--md5'] passwd
# If used in the first section of a menu file, disable all interactive editing
# control (menu entry editor and command-line)  and entries protected by the
# command 'lock'
# e.g. password topsecret
## password --md5 $1$gLhU0/$aW78kHK1QfV3P2b2znUoe/
# password topsecret

#
# examples
#
# title        Windows 95/98/NT/2000
# root        (hd0,0)
# makeactive
# chainloader    +1
#
# title        Linux
# root        (hd0,1)
# kernel    /vmlinuz root=/dev/hda2 ro
#

#
# Put static boot stanzas before and/or after AUTOMAGIC KERNEL LIST

### BEGIN AUTOMAGIC KERNELS LIST
## lines between the AUTOMAGIC KERNELS LIST markers will be modified
## by the debian update-grub script except for the default options below

## DO NOT UNCOMMENT THEM, Just edit them to your needs

## ## Start Default Options ##
## default kernel options
## default kernel options for automagic boot options
## If you want special options for specific kernels use kopt_x_y_z
## where x.y.z is kernel version. Minor versions can be omitted.
## e.g. kopt=root=/dev/hda1 ro
##      kopt_2_6_8=root=/dev/hdc1 ro
##      kopt_2_6_8_2_686=root=/dev/hdc2 ro
# kopt=root=UUID=979a9b56-34e2-4212-bc81-86b00cabffa7 ro

## default grub root device
## e.g. groot=(hd0,0)
# groot=979a9b56-34e2-4212-bc81-86b00cabffa7

## should update-grub create alternative automagic boot options
## e.g. alternative=true
##      alternative=false
# alternative=true

## should update-grub lock alternative automagic boot options
## e.g. lockalternative=true
##      lockalternative=false
# lockalternative=false

## additional options to use with the default boot option, but not with the
## alternatives
## e.g. defoptions=vga=791 resume=/dev/hda5
# defoptions=quiet splash

## should update-grub lock old automagic boot options
## e.g. lockold=false
##      lockold=true
# lockold=false

## Xen hypervisor options to use with the default Xen boot option
# xenhopt=

## Xen Linux kernel options to use with the default Xen boot option
# xenkopt=console=tty0

## altoption boot targets option
## multiple altoptions lines are allowed
## e.g. altoptions=(extra menu suffix) extra boot options
##      altoptions=(recovery) single
# altoptions=(recovery mode) single

## controls how many kernels should be put into the menu.lst
## only counts the first occurence of a kernel, not the
## alternative kernel options
## e.g. howmany=all
##      howmany=7
# howmany=all

## specify if running in Xen domU or have grub detect automatically
## update-grub will ignore non-xen kernels when running in domU and vice versa
## e.g. indomU=detect
##      indomU=true
##      indomU=false
# indomU=detect

## should update-grub create memtest86 boot option
## e.g. memtest86=true
##      memtest86=false
# memtest86=true

## should update-grub adjust the value of the default booted system
## can be true or false
# updatedefaultentry=false

## should update-grub add savedefault to the default options
## can be true or false
# savedefault=false

## ## End Default Options ##

title        Ubuntu 9.04, kernel 2.6.28-15-generic
uuid        979a9b56-34e2-4212-bc81-86b00cabffa7
kernel        /boot/vmlinuz-2.6.28-15-generic root=UUID=979a9b56-34e2-4212-bc81-86b00cabffa7 ro quiet splash
initrd        /boot/initrd.img-2.6.28-15-generic
quiet

title        Ubuntu 9.04, kernel 2.6.28-15-generic (recovery mode)
uuid        979a9b56-34e2-4212-bc81-86b00cabffa7
kernel        /boot/vmlinuz-2.6.28-15-generic root=UUID=979a9b56-34e2-4212-bc81-86b00cabffa7 ro  single
initrd        /boot/initrd.img-2.6.28-15-generic

title        Ubuntu 9.04, kernel 2.6.28-11-generic
uuid        979a9b56-34e2-4212-bc81-86b00cabffa7
kernel        /boot/vmlinuz-2.6.28-11-generic root=UUID=979a9b56-34e2-4212-bc81-86b00cabffa7 ro quiet splash
initrd        /boot/initrd.img-2.6.28-11-generic
quiet

title        Ubuntu 9.04, kernel 2.6.28-11-generic (recovery mode)
uuid        979a9b56-34e2-4212-bc81-86b00cabffa7
kernel        /boot/vmlinuz-2.6.28-11-generic root=UUID=979a9b56-34e2-4212-bc81-86b00cabffa7 ro  single
initrd        /boot/initrd.img-2.6.28-11-generic

title        Ubuntu 9.04, memtest86+
uuid        979a9b56-34e2-4212-bc81-86b00cabffa7
kernel        /boot/memtest86+.bin
quiet

### END DEBIAN AUTOMAGIC KERNELS LIST

[Grenka]

Тут вот какая мысль пришла. При загрузке наверника лог-файл ведётся. Погуглил и вот.

содержимое файла /var/log/dmesg позволяют посмотреть сообщения ядра Linux при последней загрузке.

Насколько я понимаю, согласно статье, в файле сохраняются сообщения только последней загрузки. Т.о. если сразу после загрузки с ошибкой (имеется ввиду загрузка до выдачи ошибки), загрузиться с установочного диска Ubuntu и скопировать dmesg файл в другое место, то скопированная копия будет содержать информацию об ошибочной загрузке. Это может помочь определиться?

[Grenka]

Ну что, есть какие-нибудь идеи?
Дополнительно.
1) брат сделал копию лог-файла /var/log/dmesg сразу после сбоя загрузки из-за ошибки, загрузившись с установочного CD.
Вот этот файл:

Код: Выделить всё

[    0.000000] BIOS EBDA/lowmem at: 0009f800/0009f800
[    0.000000] Initializing cgroup subsys cpuset
[    0.000000] Initializing cgroup subsys cpu
[    0.000000] Linux version 2.6.28-11-generic (buildd@palmer) (gcc version 4.3.3 (Ubuntu 4.3.3-5ubuntu4) ) #42-Ubuntu SMP Fri Apr 17 01:57:59 UTC 2009 (Ubuntu 2.6.28-11.42-generic)
[    0.000000] KERNEL supported cpus:
[    0.000000]   Intel GenuineIntel
[    0.000000]   AMD AuthenticAMD
[    0.000000]   NSC Geode by NSC
[    0.000000]   Cyrix CyrixInstead
[    0.000000]   Centaur CentaurHauls
[    0.000000]   Transmeta GenuineTMx86
[    0.000000]   Transmeta TransmetaCPU
[    0.000000]   UMC UMC UMC UMC
[    0.000000] BIOS-provided physical RAM map:
[    0.000000]  BIOS-e820: 0000000000000000 - 000000000009f800 (usable)
[    0.000000]  BIOS-e820: 000000000009f800 - 00000000000a0000 (reserved)
[    0.000000]  BIOS-e820: 00000000000f0000 - 0000000000100000 (reserved)
[    0.000000]  BIOS-e820: 0000000000100000 - 000000007fff0000 (usable)
[    0.000000]  BIOS-e820: 000000007fff0000 - 000000007fff3000 (ACPI NVS)
[    0.000000]  BIOS-e820: 000000007fff3000 - 0000000080000000 (ACPI data)
[    0.000000]  BIOS-e820: 00000000f0000000 - 00000000f2000000 (reserved)
[    0.000000]  BIOS-e820: 00000000fec00000 - 0000000100000000 (reserved)
[    0.000000] DMI 2.3 present.
[    0.000000] last_pfn = 0x7fff0 max_arch_pfn = 0x100000
[    0.000000] Scanning 2 areas for low memory corruption
[    0.000000] modified physical RAM map:
[    0.000000]  modified: 0000000000000000 - 0000000000002000 (usable)
[    0.000000]  modified: 0000000000002000 - 0000000000006000 (reserved)
[    0.000000]  modified: 0000000000006000 - 0000000000007000 (usable)
[    0.000000]  modified: 0000000000007000 - 0000000000010000 (reserved)
[    0.000000]  modified: 0000000000010000 - 0000000000092800 (usable)
[    0.000000]  modified: 000000000009f800 - 00000000000a0000 (reserved)
[    0.000000]  modified: 00000000000f0000 - 0000000000100000 (reserved)
[    0.000000]  modified: 0000000000100000 - 000000007fff0000 (usable)
[    0.000000]  modified: 000000007fff0000 - 000000007fff3000 (ACPI NVS)
[    0.000000]  modified: 000000007fff3000 - 0000000080000000 (ACPI data)
[    0.000000]  modified: 00000000f0000000 - 00000000f2000000 (reserved)
[    0.000000]  modified: 00000000fec00000 - 0000000100000000 (reserved)
[    0.000000] kernel direct mapping tables up to 373fe000 @ 10000-16000
[    0.000000] RAMDISK: 378bf000 - 37fef73a
[    0.000000] Allocated new RAMDISK: 00881000 - 00fb173a
[    0.000000] Move RAMDISK from 00000000378bf000 - 0000000037fef739 to 00881000 - 00fb1739
[    0.000000] ACPI: RSDP 000F62B0, 0014 (r0 GBT   )
[    0.000000] ACPI: RSDT 7FFF3000, 0038 (r1 GBT    NVDAACPI 42302E31 NVDA  1010101)
[    0.000000] ACPI: FACP 7FFF3040, 0074 (r1 GBT    NVDAACPI 42302E31 NVDA  1010101)
[    0.000000] ACPI: DSDT 7FFF30C0, 453B (r1 GBT    NVDAACPI     1000 MSFT  100000C)
[    0.000000] ACPI: FACS 7FFF0000, 0040
[    0.000000] ACPI: SSDT 7FFF7680, 0248 (r1 PTLTD  POWERNOW        1  LTP        1)
[    0.000000] ACPI: HPET 7FFF7900, 0038 (r1 GBT    NVDAACPI 42302E31 NVDA       98)
[    0.000000] ACPI: MCFG 7FFF7940, 003C (r1 GBT    NVDAACPI 42302E31 NVDA  1010101)
[    0.000000] ACPI: APIC 7FFF7600, 007C (r1 GBT    NVDAACPI 42302E31 NVDA  1010101)
[    0.000000] ACPI: Local APIC address 0xfee00000
[    0.000000] 1163MB HIGHMEM available.
[    0.000000] 883MB LOWMEM available.
[    0.000000]   mapped low ram: 0 - 373fe000
[    0.000000]   low ram: 00000000 - 373fe000
[    0.000000]   bootmap 00012000 - 00018e80
[    0.000000] (9 early reservations) ==> bootmem [0000000000 - 00373fe000]
[    0.000000]   #0 [0000000000 - 0000001000]   BIOS data page ==> [0000000000 - 0000001000]
[    0.000000]   #1 [0000001000 - 0000002000]    EX TRAMPOLINE ==> [0000001000 - 0000002000]
[    0.000000]   #2 [0000006000 - 0000007000]       TRAMPOLINE ==> [0000006000 - 0000007000]
[    0.000000]   #3 [0000100000 - 000087c52c]    TEXT DATA BSS ==> [0000100000 - 000087c52c]
[    0.000000]   #4 [000087d000 - 0000881000]    INIT_PG_TABLE ==> [000087d000 - 0000881000]
[    0.000000]   #5 [000009f800 - 0000100000]    BIOS reserved ==> [000009f800 - 0000100000]
[    0.000000]   #6 [0000010000 - 0000012000]          PGTABLE ==> [0000010000 - 0000012000]
[    0.000000]   #7 [0000881000 - 0000fb173a]      NEW RAMDISK ==> [0000881000 - 0000fb173a]
[    0.000000]   #8 [0000012000 - 0000019000]          BOOTMAP ==> [0000012000 - 0000019000]
[    0.000000] found SMP MP-table at [c00f4900] 000f4900
[    0.000000] Zone PFN ranges:
[    0.000000]   DMA      0x00000000 -> 0x00001000
[    0.000000]   Normal   0x00001000 -> 0x000373fe
[    0.000000]   HighMem  0x000373fe -> 0x0007fff0
[    0.000000] Movable zone start PFN for each node
[    0.000000] early_node_map[4] active PFN ranges
[    0.000000]     0: 0x00000000 -> 0x00000002
[    0.000000]     0: 0x00000006 -> 0x00000007
[    0.000000]     0: 0x00000010 -> 0x00000092
[    0.000000]     0: 0x00000100 -> 0x0007fff0
[    0.000000] On node 0 totalpages: 524149
[    0.000000] free_area_init_node: node 0, pgdat c06d0f80, node_mem_map c1000000
[    0.000000]   DMA zone: 32 pages used for memmap
[    0.000000]   DMA zone: 0 pages reserved
[    0.000000]   DMA zone: 3941 pages, LIFO batch:0
[    0.000000]   Normal zone: 1736 pages used for memmap
[    0.000000]   Normal zone: 220470 pages, LIFO batch:31
[    0.000000]   HighMem zone: 2328 pages used for memmap
[    0.000000]   HighMem zone: 295642 pages, LIFO batch:31
[    0.000000]   Movable zone: 0 pages used for memmap
[    0.000000] Detected use of extended apic ids on hypertransport bus
[    0.000000] ACPI: PM-Timer IO Port: 0x1008
[    0.000000] ACPI: Local APIC address 0xfee00000
[    0.000000] ACPI: LAPIC (acpi_id[0x00] lapic_id[0x00] enabled)
[    0.000000] ACPI: LAPIC (acpi_id[0x01] lapic_id[0x01] enabled)
[    0.000000] ACPI: LAPIC_NMI (acpi_id[0x00] dfl dfl lint[0x1])
[    0.000000] ACPI: LAPIC_NMI (acpi_id[0x01] dfl dfl lint[0x1])
[    0.000000] ACPI: IOAPIC (id[0x02] address[0xfec00000] gsi_base[0])
[    0.000000] IOAPIC[0]: apic_id 2, version 17, address 0xfec00000, GSI 0-23
[    0.000000] ACPI: INT_SRC_OVR (bus 0 bus_irq 0 global_irq 2 dfl dfl)
[    0.000000] ACPI: INT_SRC_OVR (bus 0 bus_irq 9 global_irq 9 high level)
[    0.000000] ACPI: INT_SRC_OVR (bus 0 bus_irq 14 global_irq 14 high edge)
[    0.000000] ACPI: INT_SRC_OVR (bus 0 bus_irq 15 global_irq 15 high edge)
[    0.000000] ACPI: IRQ0 used by override.
[    0.000000] ACPI: IRQ2 used by override.
[    0.000000] ACPI: IRQ9 used by override.
[    0.000000] ACPI: IRQ14 used by override.
[    0.000000] ACPI: IRQ15 used by override.
[    0.000000] Enabling APIC mode:  Flat.  Using 1 I/O APICs
[    0.000000] ACPI: HPET id: 0x10de8201 base: 0xfeff0000
[    0.000000] Using ACPI (MADT) for SMP configuration information
[    0.000000] SMP: Allowing 2 CPUs, 0 hotplug CPUs
[    0.000000] PM: Registered nosave memory: 0000000000002000 - 0000000000006000
[    0.000000] PM: Registered nosave memory: 0000000000007000 - 0000000000010000
[    0.000000] PM: Registered nosave memory: 0000000000092000 - 00000000000a0000
[    0.000000] PM: Registered nosave memory: 00000000000a0000 - 00000000000f0000
[    0.000000] PM: Registered nosave memory: 00000000000f0000 - 0000000000100000
[    0.000000] Allocating PCI resources starting at 88000000 (gap: 80000000:70000000)
[    0.000000] PERCPU: Allocating 45056 bytes of per cpu data
[    0.000000] NR_CPUS: 64, nr_cpu_ids: 2, nr_node_ids 1
[    0.000000] Built 1 zonelists in Zone order, mobility grouping on.  Total pages: 520053
[    0.000000] Kernel command line: root=UUID=979a9b56-34e2-4212-bc81-86b00cabffa7 ro quiet splash
[    0.000000] Enabling fast FPU save and restore... done.
[    0.000000] Enabling unmasked SIMD FPU exception support... done.
[    0.000000] Initializing CPU#0
[    0.000000] PID hash table entries: 4096 (order: 12, 16384 bytes)
[    0.000000] Fast TSC calibration using PIT
[    0.000000] Detected 2310.500 MHz processor.
[    0.004000] spurious 8259A interrupt: IRQ7.
[    0.004000] Console: colour VGA+ 80x25
[    0.004000] console [tty0] enabled
[    0.004000] Dentry cache hash table entries: 131072 (order: 7, 524288 bytes)
[    0.004000] Inode-cache hash table entries: 65536 (order: 6, 262144 bytes)
[    0.004000] allocated 10485440 bytes of page_cgroup
[    0.004000] please try cgroup_disable=memory option if you don't want
[    0.004000] Scanning for low memory corruption every 60 seconds
[    0.004000] Memory: 2053004k/2097088k available (4126k kernel code, 42628k reserved, 2208k data, 532k init, 1191880k highmem)
[    0.004000] virtual kernel memory layout:
[    0.004000]     fixmap  : 0xffc77000 - 0xfffff000   (3616 kB)
[    0.004000]     pkmap   : 0xff400000 - 0xff800000   (4096 kB)
[    0.004000]     vmalloc : 0xf7bfe000 - 0xff3fe000   ( 120 MB)
[    0.004000]     lowmem  : 0xc0000000 - 0xf73fe000   ( 883 MB)
[    0.004000]       .init : 0xc0737000 - 0xc07bc000   ( 532 kB)
[    0.004000]       .data : 0xc0507a6f - 0xc072fe60   (2208 kB)
[    0.004000]       .text : 0xc0100000 - 0xc0507a6f   (4126 kB)
[    0.004000] Checking if this processor honours the WP bit even in supervisor mode...Ok.
[    0.004000] SLUB: Genslabs=12, HWalign=64, Order=0-3, MinObjects=0, CPUs=2, Nodes=1
[    0.004000] hpet clockevent registered
[    0.004000] HPET: 3 timers in total, 0 timers will be used for per-cpu timer
[    0.004000] Calibrating delay loop (skipped), value calculated using timer frequency.. 4621.00 BogoMIPS (lpj=9242000)
[    0.004000] Security Framework initialized
[    0.004000] SELinux:  Disabled at boot.
[    0.004000] AppArmor: AppArmor initialized
[    0.004000] Mount-cache hash table entries: 512
[    0.004000] Initializing cgroup subsys ns
[    0.004000] Initializing cgroup subsys cpuacct
[    0.004000] Initializing cgroup subsys memory
[    0.004000] Initializing cgroup subsys freezer
[    0.004000] CPU: L1 I Cache: 64K (64 bytes/line), D cache 64K (64 bytes/line)
[    0.004000] CPU: L2 Cache: 512K (64 bytes/line)
[    0.004000] CPU: Physical Processor ID: 0
[    0.004000] CPU: Processor Core ID: 0
[    0.004000] using C1E aware idle routine
[    0.004000] Checking 'hlt' instruction... OK.
[    0.017666] ACPI: Core revision 20080926
[    0.018909] ACPI: Checking initramfs for custom DSDT
[    0.263687] ..TIMER: vector=0x30 apic1=0 pin1=2 apic2=-1 pin2=-1
[    0.303379] CPU0: AMD Athlon(tm) 64 X2 Dual Core Processor 4400+ stepping 01
[    0.304001] Booting processor 1 APIC 0x1 ip 0x6000
[    0.004000] Initializing CPU#1
[    0.004000] Calibrating delay using timer specific routine.. 4620.95 BogoMIPS (lpj=9241912)
[    0.004000] CPU: L1 I Cache: 64K (64 bytes/line), D cache 64K (64 bytes/line)
[    0.004000] CPU: L2 Cache: 512K (64 bytes/line)
[    0.004000] CPU: Physical Processor ID: 0
[    0.004000] CPU: Processor Core ID: 1
[    0.388213] CPU1: AMD Athlon(tm) 64 X2 Dual Core Processor 4400+ stepping 01
[    0.388261] Brought up 2 CPUs
[    0.388263] Total of 2 processors activated (9241.95 BogoMIPS).
[    0.388329] CPU0 attaching sched-domain:
[    0.388331]  domain 0: span 0-1 level CPU
[    0.388333]   groups: 0 1
[    0.388338] CPU1 attaching sched-domain:
[    0.388340]  domain 0: span 0-1 level CPU
[    0.388342]   groups: 1 0
[    0.388396] net_namespace: 776 bytes
[    0.388396] Booting paravirtualized kernel on bare hardware
[    0.388396] Time: 14:15:48  Date: 09/14/09
[    0.388396] regulator: core version 0.5
[    0.388396] NET: Registered protocol family 16
[    0.388396] EISA bus registered
[    0.388396] ACPI: bus type pci registered
[    0.388396] PCI: MCFG configuration 0: base f0000000 segment 0 buses 0 - 31
[    0.388396] PCI: MCFG area at f0000000 reserved in E820
[    0.388396] PCI: Using MMCONFIG for extended config space
[    0.388396] PCI: Using configuration type 1 for base access
[    0.388910] ACPI: EC: Look up EC in DSDT
[    0.396385] ACPI: Interpreter enabled
[    0.396388] ACPI: (supports S0 S1 S4 S5)
[    0.396404] ACPI: Using IOAPIC for interrupt routing
[    0.403683] ACPI: No dock devices found.
[    0.403693] ACPI: PCI Root Bridge [PCI0] (0000:00)
[    0.403870] pci 0000:00:01.1: reg 10 io port: [0xe400-0xe43f]
[    0.403880] pci 0000:00:01.1: reg 20 io port: [0x1c00-0x1c3f]
[    0.403884] pci 0000:00:01.1: reg 24 io port: [0xb400-0xb43f]
[    0.403894] pci 0000:00:01.1: PME# supported from D3hot D3cold
[    0.403899] pci 0000:00:01.1: PME# disabled
[    0.403941] pci 0000:00:02.0: reg 10 32bit mmio: [0xf5107000-0xf5107fff]
[    0.403957] pci 0000:00:02.0: supports D1 D2
[    0.403959] pci 0000:00:02.0: PME# supported from D0 D1 D2 D3hot D3cold
[    0.403962] pci 0000:00:02.0: PME# disabled
[    0.403981] pci 0000:00:02.1: reg 10 32bit mmio: [0xf5108000-0xf51080ff]
[    0.404004] pci 0000:00:02.1: supports D1 D2
[    0.404005] pci 0000:00:02.1: PME# supported from D0 D1 D2 D3hot D3cold
[    0.404008] pci 0000:00:02.1: PME# disabled
[    0.404058] pci 0000:00:05.0: reg 10 32bit mmio: [0xf5100000-0xf5103fff]
[    0.404075] pci 0000:00:05.0: PME# supported from D3hot D3cold
[    0.404077] pci 0000:00:05.0: PME# disabled
[    0.404108] pci 0000:00:06.0: reg 20 io port: [0xf000-0xf00f]
[    0.404136] pci 0000:00:07.0: reg 10 32bit mmio: [0xf5104000-0xf5104fff]
[    0.404139] pci 0000:00:07.0: reg 14 io port: [0xb800-0xb807]
[    0.404152] pci 0000:00:07.0: supports D1 D2
[    0.404153] pci 0000:00:07.0: PME# supported from D0 D1 D2 D3hot D3cold
[    0.404157] pci 0000:00:07.0: PME# disabled
[    0.404176] pci 0000:00:08.0: reg 10 io port: [0x9f0-0x9f7]
[    0.404179] pci 0000:00:08.0: reg 14 io port: [0xbf0-0xbf3]
[    0.404182] pci 0000:00:08.0: reg 18 io port: [0x970-0x977]
[    0.404185] pci 0000:00:08.0: reg 1c io port: [0xb70-0xb73]
[    0.404189] pci 0000:00:08.0: reg 20 io port: [0xcc00-0xcc0f]
[    0.404192] pci 0000:00:08.0: reg 24 32bit mmio: [0xf5105000-0xf5105fff]
[    0.404214] pci 0000:00:08.1: reg 10 io port: [0x9e0-0x9e7]
[    0.404217] pci 0000:00:08.1: reg 14 io port: [0xbe0-0xbe3]
[    0.404220] pci 0000:00:08.1: reg 18 io port: [0x960-0x967]
[    0.404223] pci 0000:00:08.1: reg 1c io port: [0xb60-0xb63]
[    0.404227] pci 0000:00:08.1: reg 20 io port: [0xe000-0xe00f]
[    0.404230] pci 0000:00:08.1: reg 24 32bit mmio: [0xf5106000-0xf5106fff]
[    0.404261] pci 0000:00:09.0: PME# supported from D0 D1 D2 D3hot D3cold
[    0.404263] pci 0000:00:09.0: PME# disabled
[    0.404365] pci 0000:01:0e.0: reg 10 32bit mmio: [0xf5004000-0xf50047ff]
[    0.404371] pci 0000:01:0e.0: reg 14 32bit mmio: [0xf5000000-0xf5003fff]
[    0.404394] pci 0000:01:0e.0: supports D1 D2
[    0.404396] pci 0000:01:0e.0: PME# supported from D0 D1 D2 D3hot
[    0.404399] pci 0000:01:0e.0: PME# disabled
[    0.404418] pci 0000:00:04.0: transparent bridge
[    0.404422] pci 0000:00:04.0: bridge 32bit mmio: [0xf5000000-0xf50fffff]
[    0.404442] pci 0000:02:00.0: reg 10 32bit mmio: [0xf2000000-0xf2ffffff]
[    0.404449] pci 0000:02:00.0: reg 14 64bit mmio: [0xe0000000-0xefffffff]
[    0.404455] pci 0000:02:00.0: reg 1c 64bit mmio: [0xf3000000-0xf3ffffff]
[    0.404459] pci 0000:02:00.0: reg 24 io port: [0xa000-0xa07f]
[    0.404464] pci 0000:02:00.0: reg 30 32bit mmio: [0x000000-0x01ffff]
[    0.404502] pci 0000:00:09.0: bridge io port: [0xa000-0xafff]
[    0.404504] pci 0000:00:09.0: bridge 32bit mmio: [0xf2000000-0xf4ffffff]
[    0.404508] pci 0000:00:09.0: bridge 64bit mmio pref: [0xe0000000-0xefffffff]
[    0.404513] bus 00 -> node 0
[    0.404519] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0._PRT]
[    0.404752] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.HUB0._PRT]
[    0.432605] ACPI: PCI Interrupt Link [LNK1] (IRQs 5 7 9 10 *11 14 15)
[    0.432739] ACPI: PCI Interrupt Link [LNK2] (IRQs 5 7 9 10 11 14 15) *0, disabled.
[    0.432874] ACPI: PCI Interrupt Link [LNK3] (IRQs *5 7 9 10 11 14 15)
[    0.433007] ACPI: PCI Interrupt Link [LNK4] (IRQs 5 7 9 10 11 14 15) *0, disabled.
[    0.433140] ACPI: PCI Interrupt Link [LNK5] (IRQs 5 7 9 10 11 14 15) *0, disabled.
[    0.433274] ACPI: PCI Interrupt Link [LNK6] (IRQs 5 7 9 10 11 14 15) *0, disabled.
[    0.433408] ACPI: PCI Interrupt Link [LNK7] (IRQs 5 7 9 10 11 14 15) *0, disabled.
[    0.433544] ACPI: PCI Interrupt Link [LNK8] (IRQs 5 7 9 10 11 14 15) *0, disabled.
[    0.433678] ACPI: PCI Interrupt Link [LIGP] (IRQs 5 7 9 10 11 14 15) *0, disabled.
[    0.433812] ACPI: PCI Interrupt Link [LP2P] (IRQs 5 7 9 10 11 14 15) *0, disabled.
[    0.433947] ACPI: PCI Interrupt Link [LUBA] (IRQs 5 7 9 *10 11 14 15)
[    0.434081] ACPI: PCI Interrupt Link [LMAC] (IRQs *5 7 9 10 11 14 15)
[    0.434215] ACPI: PCI Interrupt Link [LAZA] (IRQs 5 7 9 *10 11 14 15)
[    0.434348] ACPI: PCI Interrupt Link [LPMU] (IRQs 5 7 9 10 11 14 15) *0, disabled.
[    0.434482] ACPI: PCI Interrupt Link [LSMB] (IRQs *5 7 9 10 11 14 15)
[    0.434617] ACPI: PCI Interrupt Link [LUB2] (IRQs 5 7 9 10 *11 14 15)
[    0.434750] ACPI: PCI Interrupt Link [LIDE] (IRQs 5 7 9 10 11 14 15) *0, disabled.
[    0.434886] ACPI: PCI Interrupt Link [LSID] (IRQs 5 7 9 10 *11 14 15)
[    0.435020] ACPI: PCI Interrupt Link [LFID] (IRQs 5 7 9 *10 11 14 15)
[    0.435188] ACPI: PCI Interrupt Link [APC1] (IRQs 16) *0
[    0.435353] ACPI: PCI Interrupt Link [APC2] (IRQs 17) *0, disabled.
[    0.435517] ACPI: PCI Interrupt Link [APC3] (IRQs 18) *0
[    0.435681] ACPI: PCI Interrupt Link [APC4] (IRQs 19) *0, disabled.
[    0.435849] ACPI: PCI Interrupt Link [APC5] (IRQs 16) *0, disabled.
[    0.436017] ACPI: PCI Interrupt Link [APC6] (IRQs 16) *0, disabled.
[    0.436182] ACPI: PCI Interrupt Link [APC7] (IRQs 16) *0, disabled.
[    0.436347] ACPI: PCI Interrupt Link [APC8] (IRQs 16) *0, disabled.
[    0.436511] ACPI: PCI Interrupt Link [AIGP] (IRQs 20 21 22 23) *0, disabled.
[    0.436677] ACPI: PCI Interrupt Link [APCF] (IRQs 20 21 22 23) *0
[    0.436843] ACPI: PCI Interrupt Link [APCH] (IRQs 20 21 22 23) *0
[    0.437008] ACPI: PCI Interrupt Link [APMU] (IRQs 20 21 22 23) *0, disabled.
[    0.437174] ACPI: PCI Interrupt Link [AAZA] (IRQs 20 21 22 23) *0
[    0.437339] ACPI: PCI Interrupt Link [APCS] (IRQs 20 21 22 23) *0
[    0.437504] ACPI: PCI Interrupt Link [APCL] (IRQs 20 21 22 23) *0
[    0.437670] ACPI: PCI Interrupt Link [APCM] (IRQs 20 21 22 23) *0, disabled.
[    0.437836] ACPI: PCI Interrupt Link [APCZ] (IRQs 20 21 22 23) *0, disabled.
[    0.438001] ACPI: PCI Interrupt Link [APSI] (IRQs 20 21 22 23) *0
[    0.438174] ACPI: PCI Interrupt Link [APSJ] (IRQs 20 21 22 23) *0
[    0.438291] ACPI: WMI: Mapper loaded
[    0.438341] SCSI subsystem initialized
[    0.438341] libata version 3.00 loaded.
[    0.438341] usbcore: registered new interface driver usbfs
[    0.438341] usbcore: registered new interface driver hub
[    0.438341] usbcore: registered new device driver usb
[    0.438341] PCI: Using ACPI for IRQ routing
[    0.444009] Bluetooth: Core ver 2.13
[    0.444024] NET: Registered protocol family 31
[    0.444024] Bluetooth: HCI device and connection manager initialized
[    0.444024] Bluetooth: HCI socket layer initialized
[    0.444024] NET: Registered protocol family 8
[    0.444024] NET: Registered protocol family 20
[    0.444028] NetLabel: Initializing
[    0.444030] NetLabel:  domain hash size = 128
[    0.444031] NetLabel:  protocols = UNLABELED CIPSOv4
[    0.444043] NetLabel:  unlabeled traffic allowed by default
[    0.444057] hpet0: at MMIO 0xfeff0000, IRQs 2, 8, 31
[    0.444061] hpet0: 3 comparators, 32-bit 25.000000 MHz counter
[    0.448059] AppArmor: AppArmor Filesystem Enabled
[    0.452012] Switched to high resolution mode on CPU 0
[    0.452273] Switched to high resolution mode on CPU 1
[    0.456014] pnp: PnP ACPI init
[    0.456022] ACPI: bus type pnp registered
[    0.460141] pnp: PnP ACPI: found 14 devices
[    0.460143] ACPI: ACPI bus type pnp unregistered
[    0.460146] PnPBIOS: Disabled by ACPI PNP
[    0.460154] system 00:01: ioport range 0x1000-0x107f has been reserved
[    0.460157] system 00:01: ioport range 0x1080-0x10ff has been reserved
[    0.460159] system 00:01: ioport range 0x1400-0x147f has been reserved
[    0.460161] system 00:01: ioport range 0x1480-0x14ff has been reserved
[    0.460164] system 00:01: ioport range 0x1800-0x187f has been reserved
[    0.460166] system 00:01: ioport range 0x1880-0x18ff has been reserved
[    0.460169] system 00:01: iomem range 0xfefe0000-0xfefe01ff has been reserved
[    0.460171] system 00:01: iomem range 0xfefe1000-0xfefe10ff has been reserved
[    0.460176] system 00:02: ioport range 0x4d0-0x4d1 has been reserved
[    0.460179] system 00:02: ioport range 0x800-0x87f has been reserved
[    0.460181] system 00:02: ioport range 0x295-0x314 has been reserved
[    0.460183] system 00:02: ioport range 0x290-0x294 has been reserved
[    0.460191] system 00:0c: iomem range 0xf0000000-0xf1ffffff has been reserved
[    0.460196] system 00:0d: iomem range 0xcde00-0xcffff has been reserved
[    0.460198] system 00:0d: iomem range 0xf0000-0xf7fff could not be reserved
[    0.460201] system 00:0d: iomem range 0xf8000-0xfbfff could not be reserved
[    0.460204] system 00:0d: iomem range 0xfc000-0xfffff could not be reserved
[    0.460206] system 00:0d: iomem range 0x7fff0000-0x7fffffff could not be reserved
[    0.460209] system 00:0d: iomem range 0xffff0000-0xffffffff has been reserved
[    0.460211] system 00:0d: iomem range 0x0-0x9ffff could not be reserved
[    0.460214] system 00:0d: iomem range 0x100000-0x7ffeffff could not be reserved
[    0.460217] system 00:0d: iomem range 0xfec00000-0xfec00fff has been reserved
[    0.460219] system 00:0d: iomem range 0xfee00000-0xfee00fff has been reserved
[    0.494893] pci 0000:00:04.0: PCI bridge, secondary bus 0000:01
[    0.494895] pci 0000:00:04.0:   IO window: disabled
[    0.494899] pci 0000:00:04.0:   MEM window: 0xf5000000-0xf50fffff
[    0.494901] pci 0000:00:04.0:   PREFETCH window: disabled
[    0.494907] pci 0000:00:09.0: PCI bridge, secondary bus 0000:02
[    0.494909] pci 0000:00:09.0:   IO window: 0xa000-0xafff
[    0.494912] pci 0000:00:09.0:   MEM window: 0xf2000000-0xf4ffffff
[    0.494914] pci 0000:00:09.0:   PREFETCH window: 0x000000e0000000-0x000000efffffff
[    0.494922] pci 0000:00:04.0: setting latency timer to 64
[    0.494926] pci 0000:00:09.0: setting latency timer to 64
[    0.494929] bus: 00 index 0 io port: [0x00-0xffff]
[    0.494931] bus: 00 index 1 mmio: [0x000000-0xffffffff]
[    0.494933] bus: 01 index 0 mmio: [0x0-0x0]
[    0.494934] bus: 01 index 1 mmio: [0xf5000000-0xf50fffff]
[    0.494936] bus: 01 index 2 mmio: [0x0-0x0]
[    0.494938] bus: 01 index 3 io port: [0x00-0xffff]
[    0.494939] bus: 01 index 4 mmio: [0x000000-0xffffffff]
[    0.494941] bus: 02 index 0 io port: [0xa000-0xafff]
[    0.494943] bus: 02 index 1 mmio: [0xf2000000-0xf4ffffff]
[    0.494945] bus: 02 index 2 mmio: [0xe0000000-0xefffffff]
[    0.494946] bus: 02 index 3 mmio: [0x0-0x0]
[    0.494955] NET: Registered protocol family 2
[    0.508055] IP route cache hash table entries: 32768 (order: 5, 131072 bytes)
[    0.508302] TCP established hash table entries: 131072 (order: 8, 1048576 bytes)
[    0.508815] TCP bind hash table entries: 65536 (order: 7, 524288 bytes)
[    0.509049] TCP: Hash tables configured (established 131072 bind 65536)
[    0.509051] TCP reno registered
[    0.516071] NET: Registered protocol family 1
[    0.516176] checking if image is initramfs... it is
[    1.017775] Freeing initrd memory: 7361k freed
[    1.017947] cpufreq: No nForce2 chipset.
[    1.018057] audit: initializing netlink socket (disabled)
[    1.018074] type=2000 audit(1252937748.016:1): initialized
[    1.024971] highmem bounce pool size: 64 pages
[    1.024975] HugeTLB registered 4 MB page size, pre-allocated 0 pages
[    1.026074] VFS: Disk quotas dquot_6.5.1
[    1.026120] Dquot-cache hash table entries: 1024 (order 0, 4096 bytes)
[    1.026626] fuse init (API version 7.10)
[    1.026695] msgmni has been set to 1698
[    1.026862] alg: No test for stdrng (krng)
[    1.026872] io scheduler noop registered
[    1.026874] io scheduler anticipatory registered
[    1.026876] io scheduler deadline registered
[    1.026889] io scheduler cfq registered (default)
[    1.026918] pci 0000:00:00.0: Enabling HT MSI Mapping
[    1.027015] pci 0000:00:04.0: Enabling HT MSI Mapping
[    1.027031] pci 0000:00:05.0: Enabling HT MSI Mapping
[    1.027057] pci 0000:00:07.0: Enabling HT MSI Mapping
[    1.027071] pci 0000:00:08.0: Enabling HT MSI Mapping
[    1.027085] pci 0000:00:08.1: Enabling HT MSI Mapping
[    1.027099] pci 0000:00:09.0: Enabling HT MSI Mapping
[    1.027120] pci 0000:02:00.0: Boot video device
[    1.032046] pcieport-driver 0000:00:09.0: setting latency timer to 64
[    1.032068] pcieport-driver 0000:00:09.0: found MSI capability
[    1.032082] pcieport-driver 0000:00:09.0: irq 2303 for MSI/MSI-X
[    1.032087] pci_express 0000:00:09.0:pcie00: allocate port service
[    1.032099] pci_express 0000:00:09.0:pcie03: allocate port service
[    1.032138] pci_hotplug: PCI Hot Plug PCI Core version: 0.5
[    1.032145] pciehp: PCI Express Hot Plug Controller Driver version: 0.4
[    1.032267] input: Power Button (FF) as /devices/LNXSYSTM:00/LNXPWRBN:00/input/input0
[    1.032269] ACPI: Power Button (FF) [PWRF]
[    1.032305] input: Power Button (CM) as /devices/LNXSYSTM:00/device:00/PNP0C0C:00/input/input1
[    1.032307] ACPI: Power Button (CM) [PWRB]
[    1.032588] processor ACPI_CPU:00: registered as cooling_device0
[    1.032617] processor ACPI_CPU:01: registered as cooling_device1
[    1.035585] isapnp: Scanning for PnP cards...
[    1.388178] isapnp: No Plug & Play device found
[    1.397124] Serial: 8250/16550 driver4 ports, IRQ sharing enabled
[    1.397210] serial8250: ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A
[    1.397294] serial8250: ttyS1 at I/O 0x2f8 (irq = 3) is a 16550A
[    1.397523] 00:08: ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A
[    1.397636] 00:09: ttyS1 at I/O 0x2f8 (irq = 3) is a 16550A
[    1.398251] brd: module loaded
[    1.398515] loop: module loaded
[    1.398568] Fixed MDIO Bus: probed
[    1.398573] PPP generic driver version 2.4.2
[    1.398622] input: Macintosh mouse button emulation as /devices/virtual/input/input2
[    1.398645] Driver 'sd' needs updating - please use bus_type methods
[    1.398652] Driver 'sr' needs updating - please use bus_type methods
[    1.398808] sata_nv 0000:00:08.0: version 3.5
[    1.399100] ACPI: PCI Interrupt Link [APSI] enabled at IRQ 23
[    1.399107] sata_nv 0000:00:08.0: PCI INT A -> Link[APSI] -> GSI 23 (level, low) -> IRQ 23
[    1.399160] sata_nv 0000:00:08.0: setting latency timer to 64
[    1.399220] scsi0 : sata_nv
[    1.399299] scsi1 : sata_nv
[    1.399423] ata1: SATA max UDMA/133 cmd 0x9f0 ctl 0xbf0 bmdma 0xcc00 irq 23
[    1.399426] ata2: SATA max UDMA/133 cmd 0x970 ctl 0xb70 bmdma 0xcc08 irq 23
[    2.184033] ata2: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
[    2.192117] ata2.00: ATAPI: HL-DT-STDVD-RAM GSA-H30N, 1.03, max UDMA/100
[    2.208125] ata2.00: configured for UDMA/100
[    2.210478] scsi 1:0:0:0: CD-ROM            HL-DT-ST DVD-RAM GSA-H30N 1.03 PQ: 0 ANSI: 5
[    2.216187] sr0: scsi3-mmc drive: 48x/48x writer dvd-ram cd/rw xa/form2 cdda tray
[    2.216190] Uniform CD-ROM driver Revision: 3.20
[    2.216277] sr 1:0:0:0: Attached scsi CD-ROM sr0
[    2.216316] sr 1:0:0:0: Attached scsi generic sg0 type 5
[    2.216586] ACPI: PCI Interrupt Link [APSJ] enabled at IRQ 22
[    2.216591] sata_nv 0000:00:08.1: PCI INT B -> Link[APSJ] -> GSI 22 (level, low) -> IRQ 22
[    2.216625] sata_nv 0000:00:08.1: setting latency timer to 64
[    2.216688] scsi2 : sata_nv
[    2.216757] scsi3 : sata_nv
[    2.216873] ata3: SATA max UDMA/133 cmd 0x9e0 ctl 0xbe0 bmdma 0xe000 irq 22
[    2.216876] ata4: SATA max UDMA/133 cmd 0x960 ctl 0xb60 bmdma 0xe008 irq 22
[    2.684033] ata3: SATA link up 3.0 Gbps (SStatus 123 SControl 300)
[    2.692204] ata3.00: ATA-7: SAMSUNG HD103UJ, 1AA01113, max UDMA7
[    2.692207] ata3.00: 1953525168 sectors, multi 16: LBA48 NCQ (depth 0/32)
[    2.700212] ata3.00: configured for UDMA/133
[    3.022256] scsi 2:0:0:0: Direct-Access     ATA      SAMSUNG HD103UJ  1AA0 PQ: 0 ANSI: 5
[    3.022338] sd 2:0:0:0: [sda] 1953525168 512-byte hardware sectors: (1.00 TB/931 GiB)
[    3.022351] sd 2:0:0:0: [sda] Write Protect is off
[    3.022354] sd 2:0:0:0: [sda] Mode Sense: 00 3a 00 00
[    3.022374] sd 2:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[    3.022425] sd 2:0:0:0: [sda] 1953525168 512-byte hardware sectors: (1.00 TB/931 GiB)
[    3.022436] sd 2:0:0:0: [sda] Write Protect is off
[    3.022438] sd 2:0:0:0: [sda] Mode Sense: 00 3a 00 00
[    3.022457] sd 2:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[    3.022461]  sda: sda1 sda2 < sda5 sda6 >
[    3.045050] sd 2:0:0:0: [sda] Attached SCSI disk
[    3.045084] sd 2:0:0:0: Attached scsi generic sg1 type 0
[    3.045163] pata_amd 0000:00:06.0: version 0.3.10
[    3.045196] pata_amd 0000:00:06.0: setting latency timer to 64
[    3.045260] scsi4 : pata_amd
[    3.045319] scsi5 : pata_amd
[    3.045786] ata5: PATA max UDMA/133 cmd 0x1f0 ctl 0x3f6 bmdma 0xf000 irq 14
[    3.045788] ata6: PATA max UDMA/133 cmd 0x170 ctl 0x376 bmdma 0xf008 irq 15
[    3.210931] ata6: port disabled. ignoring.
[    3.211351] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
[    3.211618] ACPI: PCI Interrupt Link [APCL] enabled at IRQ 21
[    3.211624] ehci_hcd 0000:00:02.1: PCI INT B -> Link[APCL] -> GSI 21 (level, low) -> IRQ 21
[    3.211638] ehci_hcd 0000:00:02.1: setting latency timer to 64
[    3.211641] ehci_hcd 0000:00:02.1: EHCI Host Controller
[    3.211688] ehci_hcd 0000:00:02.1: new USB bus registered, assigned bus number 1
[    3.211716] ehci_hcd 0000:00:02.1: debug port 1
[    3.211720] ehci_hcd 0000:00:02.1: cache line size of 64 is not supported
[    3.211732] ehci_hcd 0000:00:02.1: irq 21, io mem 0xf5108000
[    3.220017] ehci_hcd 0000:00:02.1: USB 2.0 started, EHCI 1.00
[    3.220079] usb usb1: configuration #1 chosen from 1 choice
[    3.220101] hub 1-0:1.0: USB hub found
[    3.220108] hub 1-0:1.0: 10 ports detected
[    3.220198] ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver
[    3.220460] ACPI: PCI Interrupt Link [APCF] enabled at IRQ 20
[    3.220464] ohci_hcd 0000:00:02.0: PCI INT A -> Link[APCF] -> GSI 20 (level, low) -> IRQ 20
[    3.220473] ohci_hcd 0000:00:02.0: setting latency timer to 64
[    3.220475] ohci_hcd 0000:00:02.0: OHCI Host Controller
[    3.220509] ohci_hcd 0000:00:02.0: new USB bus registered, assigned bus number 2
[    3.220526] ohci_hcd 0000:00:02.0: irq 20, io mem 0xf5107000
[    3.278038] usb usb2: configuration #1 chosen from 1 choice
[    3.278057] hub 2-0:1.0: USB hub found
[    3.278064] hub 2-0:1.0: 10 ports detected
[    3.278147] uhci_hcd: USB Universal Host Controller Interface driver
[    3.278199] usbcore: registered new interface driver libusual
[    3.278224] usbcore: registered new interface driver usbserial
[    3.278233] USB Serial support registered for generic
[    3.278243] usbcore: registered new interface driver usbserial_generic
[    3.278245] usbserial: USB Serial Driver core
[    3.278281] PNP: PS/2 Controller [PNP0303:PS2K] at 0x60,0x64 irq 1
[    3.278284] PNP: PS/2 appears to have AUX port disabled, if this is incorrect please boot with i8042.nopnp
[    3.278356] serio: i8042 KBD port at 0x60,0x64 irq 1
[    3.281036] mice: PS/2 mouse device common for all mice
[    3.293064] rtc_cmos 00:04: RTC can wake from S4
[    3.293093] rtc_cmos 00:04: rtc core: registered rtc_cmos as rtc0
[    3.293127] rtc0: alarms up to one year, y3k, 242 bytes nvram, hpet irqs
[    3.293177] device-mapper: uevent: version 1.0.3
[    3.293259] device-mapper: ioctl: 4.14.0-ioctl (2008-04-23) initialised: dm-devel@redhat.com
[    3.293390] device-mapper: multipath: version 1.0.5 loaded
[    3.293392] device-mapper: multipath round-robin: version 1.0.0 loaded
[    3.293479] EISA: Probing bus 0 at eisa.0
[    3.293484] Cannot allocate resource for EISA slot 1
[    3.293502] EISA: Detected 0 cards.
[    3.293589] cpuidle: using governor ladder
[    3.293591] cpuidle: using governor menu
[    3.294001] TCP cubic registered
[    3.294081] NET: Registered protocol family 10
[    3.294411] lo: Disabled Privacy Extensions
[    3.294665] NET: Registered protocol family 17
[    3.294680] Bluetooth: L2CAP ver 2.11
[    3.294682] Bluetooth: L2CAP socket layer initialized
[    3.294684] Bluetooth: SCO (Voice Link) ver 0.6
[    3.294686] Bluetooth: SCO socket layer initialized
[    3.294727] Bluetooth: RFCOMM socket layer initialized
[    3.294731] Bluetooth: RFCOMM TTY layer initialized
[    3.294733] Bluetooth: RFCOMM ver 1.10
[    3.294776] powernow-k8: Found 1 AMD Athlon(tm) 64 X2 Dual Core Processor 4400+ processors (2 cpu cores) (version 2.20.00)
[    3.294826] powernow-k8:    0 : fid 0xf (2300 MHz), vid 0x9
[    3.294829] powernow-k8:    1 : fid 0xe (2200 MHz), vid 0xa
[    3.294830] powernow-k8:    2 : fid 0xc (2000 MHz), vid 0xc
[    3.294832] powernow-k8:    3 : fid 0xa (1800 MHz), vid 0xe
[    3.294834] powernow-k8:    4 : fid 0x2 (1000 MHz), vid 0x12
[    3.294883] Using IPI No-Shortcut mode
[    3.294960] registered taskstats version 1
[    3.295064]   Magic number: 9:274:283
[    3.295162] rtc_cmos 00:04: setting system clock to 2009-09-14 14:15:51 UTC (1252937751)
[    3.295165] BIOS EDD facility v0.16 2004-Jun-25, 0 devices found
[    3.295166] EDD information not available.
[    3.295463] Freeing unused kernel memory: 532k freed
[    3.295592] Write protecting the kernel text: 4128k
[    3.295637] Write protecting the kernel read-only data: 1532k
[    3.308158] input: AT Translated Set 2 keyboard as /devices/platform/i8042/serio0/input/input3
[    3.483891] forcedeth: Reverse Engineered nForce ethernet driver. Version 0.61.
[    3.484221] ACPI: PCI Interrupt Link [APCH] enabled at IRQ 23
[    3.484226] forcedeth 0000:00:07.0: PCI INT A -> Link[APCH] -> GSI 23 (level, low) -> IRQ 23
[    3.484230] forcedeth 0000:00:07.0: setting latency timer to 64
[    3.532186] ACPI: PCI Interrupt Link [APC3] enabled at IRQ 18
[    3.532194] ohci1394 0000:01:0e.0: PCI INT A -> Link[APC3] -> GSI 18 (level, low) -> IRQ 18
[    3.587420] ohci1394: fw-host0: OHCI-1394 1.1 (PCI): IRQ=[18]  MMIO=[f5004000-f50047ff]  Max Packet=[2048]  IR/IT contexts=[4/8]
[    3.614789] Floppy drive(s): fd0 is 1.44M
[    3.636112] FDC 0 is a post-1991 82077
[    3.977016] usb 2-1: new low speed USB device using ohci_hcd and address 2
[    4.073120] forcedeth 0000:00:07.0: ifname eth0, PHY OUI 0x732 @ 1, addr 00:1a:4d:62:7a:53
[    4.073124] forcedeth 0000:00:07.0: highdma pwrctl mgmt timirq gbit lnktim msi desc-v3
[    4.142705] PM: Starting manual resume from disk
[    4.142709] PM: Resume from partition 8:6
[    4.142710] PM: Checking hibernation image.
[    4.142858] PM: Resume from disk failed.
[    4.166062] kjournald starting.  Commit interval 5 seconds
[    4.166072] EXT3-fs: mounted filesystem with ordered data mode.
[    4.191089] usb 2-1: configuration #1 chosen from 1 choice
[    4.516014] usb 2-4: new full speed USB device using ohci_hcd and address 3
[    4.729091] usb 2-4: configuration #1 chosen from 1 choice
[    4.825498] ieee1394: Host added: ID:BUS[0-00:1023]  GUID[0016e60000e03937]
[    7.263039] udev: starting version 141
[    7.649411] parport_pc 00:0a: reported by Plug and Play ACPI
[    7.649456] parport0: PC-style at 0x378, irq 7 [PCSPP,TRISTATE]
[    7.664120] usbcore: registered new interface driver hiddev
[    7.670329] input: Logitech USB Receiver as /devices/pci0000:00/0000:00:02.0/usb2/2-1/2-1:1.0/input/input4
[    7.676277] generic-usb 0003:046D:C51B.0001: input,hidraw0: USB HID v1.11 Mouse [Logitech USB Receiver] on usb-0000:00:02.0-1/input0
[    7.684224] generic-usb 0003:046D:C51B.0002: hiddev96,hidraw1: USB HID v1.11 Device [Logitech USB Receiver] on usb-0000:00:02.0-1/input1
[    7.684247] usbcore: registered new interface driver usbhid
[    7.684267] usbhid: v2.6:USB HID core driver
[    7.693356] input: PC Speaker as /devices/platform/pcspkr/input/input5
[    7.845069] Linux agpgart interface v0.103
[    7.869763] i2c-adapter i2c-0: nForce2 SMBus adapter at 0x1c00
[    7.869779] i2c-adapter i2c-1: nForce2 SMBus adapter at 0xb400
[    7.871521] ppdev: user-space parallel port driver
[    7.879477] Linux video capture interface: v2.00
[    7.986511] nvidia: module license 'NVIDIA' taints kernel.
[    8.241054] ACPI: PCI Interrupt Link [APC8] enabled at IRQ 16
[    8.241063] nvidia 0000:02:00.0: PCI INT A -> Link[APC8] -> GSI 16 (level, low) -> IRQ 16
[    8.241070] nvidia 0000:02:00.0: setting latency timer to 64
[    8.241698] NVRM: loading NVIDIA UNIX x86 Kernel Module  180.44  Mon Mar 23 14:59:10 PST 2009
[    8.250713] gspca: main v2.3.0 registered
[    8.254627] gspca: probing 05a9:4519
[    8.345572] ACPI: PCI Interrupt Link [AAZA] enabled at IRQ 22
[    8.345578] HDA Intel 0000:00:05.0: PCI INT B -> Link[AAZA] -> GSI 22 (level, low) -> IRQ 22
[    8.345637] HDA Intel 0000:00:05.0: setting latency timer to 64
[    8.495024] ov519: I2C synced in 1 attempt(s)
[    8.495026] ov519: starting OV7xx0 configuration
[    8.531028] ov519: Sensor is an OV7648
[    8.569105] gspca: probe ok
[    8.569114] gspca: probing 05a9:4519
[    8.569122] gspca: probing 05a9:4519
[    8.569138] usbcore: registered new interface driver ov519
[    8.569158] ov519: registered
[    8.680425] usbcore: registered new interface driver snd-usb-audio
[    9.029180] lp0: using parport0 (interrupt-driven).
[    9.116559] Adding 2000052k swap on /dev/sda6.  Priority:-1 extents:1 across:2000052k
[    9.648757] EXT3 FS on sda5, internal journal
[   11.736349] type=1505 audit(1252937759.937:2): operation="profile_load" name="/usr/share/gdm/guest-session/Xsession" name2="default" pid=2015
[   11.783010] type=1505 audit(1252937759.985:3): operation="profile_load" name="/sbin/dhclient-script" name2="default" pid=2019
[   11.783130] type=1505 audit(1252937759.985:4): operation="profile_load" name="/sbin/dhclient3" name2="default" pid=2019
[   11.783177] type=1505 audit(1252937759.985:5): operation="profile_load" name="/usr/lib/NetworkManager/nm-dhcp-client.action" name2="default" pid=2019
[   11.783217] type=1505 audit(1252937759.985:6): operation="profile_load" name="/usr/lib/connman/scripts/dhclient-script" name2="default" pid=2019
[   11.914548] type=1505 audit(1252937760.117:7): operation="profile_load" name="/usr/lib/cups/backend/cups-pdf" name2="default" pid=2024
[   11.914728] type=1505 audit(1252937760.117:8): operation="profile_load" name="/usr/sbin/cupsd" name2="default" pid=2024
[   11.941111] type=1505 audit(1252937760.145:9): operation="profile_load" name="/usr/sbin/tcpdump" name2="default" pid=2028
[   12.072139] ip_tables: (C) 2000-2006 Netfilter Core Team
[   12.088360] nf_conntrack version 0.5.0 (16384 buckets, 65536 max)
[   12.089283] CONFIG_NF_CT_ACCT is deprecated and will be removed soon. Please use
[   12.089286] nf_conntrack.acct=1 kernel paramater, acct=1 nf_conntrack module option or
[   12.089288] sysctl net.netfilter.nf_conntrack_acct=1 to enable it.
[   12.118456] ip6_tables: (C) 2000-2006 Netfilter Core Team
[   15.077748] Bluetooth: BNEP (Ethernet Emulation) ver 1.3
[   15.077751] Bluetooth: BNEP filters: protocol multicast
[   15.095089] Bridge firewalling registered

Правда я не вижу особой разницы от dmesg нормальной загрузки. Никаких сообщений типа error или bug не обнаружил. Возможно система, при ошибке bug int 14, просто не доходит до того момента загрузки, когда она начинает что-либо записывать в dmesg.
2) При первой попытке загрузиться с установочного CD (сразу после ошибке загрузки системы с винчестера) выскочила таже ошибка. Т.е. при загрузки с CD тоже иногда выдаётся bug int 14. На мой взгляд это может быть из-за:
a) битого CD. Хотя проверку CD проводили средствами самого установочного CD (пункт "Проверить CD")
б) 32-х битная версия так работает с 64-битным процессором, независимо от того, откуда она грузится с винчестера или CD.
в) проблемы с железом.

Буду рад услышать Ваши предположения, теории, советы.

[blackdevil]

32-х битная версия так работает с 64-битным процессором, независимо от того, откуда она грузится с винчестера или CD

точно не это, 64битные железки отлично поддерживают 32битные системы

проблемы с железом

вполне может быть...надо бы прогнать тест памяти (memtest86), проверить жесткий диск на битые сектора, мониторить температуру...Попробовать параметры ядры acpi=off noapic и так далее.

[Grenka]

точно не это, 64битные железки отлично поддерживают 32битные системы

Сделали резервную копию 32-битной системы. Поставили 64-битную. Через раз глючит при загрузке. Но ошибка другая. См. скриншот. Восстановили 32-битную.

вполне может быть...надо бы прогнать тест памяти (memtest86), проверить жесткий диск на битые сектора, мониторить температуру...

Тест памяти запустили с установочного диска Ubuntu.
Какие программы посоветуете для жёсткого диска и контроля температуры?

Попробовать параметры ядры acpi=off noapic

Раз Вы указываете такой параметр, то у Вас есть довольно конкретные догадки о причине ошибки. Интересно какие? А вот нашёл интересную статейку. Проблема похожа на мою. Почитаю.

До этого на компе стояли винды, они тормозили конечно, но при загрузке не глючили. Непонятно, если дело в железе, то почему виндовз не глючил при загрузке.

[Grenka]

Прочитал следующие статьи:
1) Ubuntu 7.04 и 7.10 acpi=off noapic
2) ubuntu hangs on boot. "acpi = off" "noapic" and "nolapic"
3) Ubuntu - How To Edit Grub Boot Parameters
В [1] была описана похожая проблема, что и у меня. Вкратце, люди добавили в menu.lst параметры acpi=off, noapic и всё заработало. Ну и после они обновили биос и вообще, не нужны даже параметры оказались.
Для начала мы решил просто запустить систему с параметрами. Как указано в [3] сначала добавили параметры в строку загрузки прямо в меню груб при загрузке (1. Changing Boot Parameters Temporarily). Добавили только acpi=off noapic. При первой же загрузке с этими параметрами снова получили bug int 14. Тогда, как написано в [2] добавили acpi=off noapic nolapic.
В результате получаем проблемы с драйверами видюхи NVIDIA. См. скриншот 1.
После <OK> получаем скриншот 2. Пробавали "Reconfigure graphics" снова экран скриншот 2. Пробовали "Run Ubuntu in low-graphics mode..." и получили скриншот 3. При выборе <Нет> снова скриншот 3. Если выбирать в окне на скриншоте 2 последние два пункта, то будет предложен один из отчётов или работа в текстовом режиме.
Т.о. подитожив, как я понимаю без ACPI не хочет работать правильно драйвер графической карты (активирован проприетарный драйвер NVIDIA). И остаётся попробовать обновить BIOS.
Правильные ли выводы я делаю на основании скриншотов? Есть ли ещё варианты кроме обновления биоса? Сложно ли обновлять биос, а то как то боизно? Наверно на сайте производителя есть прошивки и инструкция.

[uptime]

Сложно ли обновлять биос, а то как то боизно? Наверно на сайте производителя есть прошивки и инструкция.

Если прошивки и инструкция найдутся на оф.сайте, то обновить биос будет полезно в любом случае. Боятся стоит только неожиданного выключения электроэнергии в процессе.

успехов

[blackdevil]

Кажется это ошибка ядра: https://bugs.launchpad.net/ubuntu/+source/linux/+bug/312554 Можно попробовать поставить более старое ядро или почитать по ссылке как люди проблему решили.

[Grenka]

Кажется это ошибка ядра: https://bugs.launchpad.net/ubuntu/+source/linux/+bug/312554 Можно попробовать поставить более старое ядро или почитать по ссылке как люди проблему решили.

Почитал. Насколько я понял они поставили ядро 2.6.28-6 и пропатчили его. Но как пользоваться указанным там патчем я не понимаю.
Поэтому попробовал как указано в [1] - обновили биос. Материнка gigabyte GA-M61PM-S2. Вчера записали биос версии F9C вместо F6. Первые 10 загрузок прошли успешно. Если так и дальше будет, то, исходя из всего выше упомянутого, дело во взаимной работе биос и ядра. Если нет, то придётся дальше копать. Спасибо всем за советы и ссылки.
P.S. Написал меил в службу тех. поддержки gigabyte с вопросом о совместимости прошивки биоса с Linux.
30.09.2009 ответ от российской службы поддержки:

...
Скорее всего, проблема в исползуемой ОС. Рекомендуем обратиться к специалистам для настройки Вашей ОС. Попробуйте также обновить ядро.
...

После обновления биоса 16.09.2009 ошибок при загрузке больше не возникало. Тук тук по дереву

[Atolstoy]

P.S. Написал меил в службу тех. поддержки gigabyte с вопросом о совместимости прошивки биоса с Linux.

Я бы предварительно протестировал бы систему с ванильным ядром или хотя бы с парой других дистрибутивов с разными ядрами.