1)Установил эмулятор wine. Решил Установить Adobe Photoshop CS4 - при нажатии на установочный файл - никакой реакции
Существует ли рабочая версия фотошопа под Wine? Программа GIMP меня не устраивает.2)При записывание диска через k3b - начинается запись диска и через 10-20 секунд выдаётся ошибка (((
Код: Выделить всё
Devices
-----------------------
HL-DT-ST DVDRAM GSA-T40N JP01 (/dev/sr0, CD-R, CD-RW, CD-ROM, DVD-ROM, DVD-R, DVD-RW, DVD-R DL, DVD+R, DVD+RW, DVD+R DL) [DVD-ROM, DVD-R Sequential, DVD-R Dual Layer Sequential, DVD-R Dual Layer Jump, DVD-RAM, DVD-RW Restricted Overwrite, DVD-RW Sequential, DVD+RW, DVD+R, DVD+R Dual Layer, CD-ROM, CD-R, CD-RW] [TAO, Ограниченная перезапись, Layer Jump] [%7]
System
-----------------------
K3b Version: 1.65.0
KDE Version: 4.3.1 (KDE 4.3.1)
QT Version: 4.5.2
Kernel: 2.6.29.6-desktop-2mnb
Used versions
-----------------------
cdrecord: 2.1.1a03
cdrecord
-----------------------
wodim: Operation not permitted. Warning: Cannot raise RLIMIT_MEMLOCK limits.scsidev: '/dev/sr0'
devname: '/dev/sr0'
scsibus: -2 target: -2 lun: -2
Linux sg driver version: 3.5.27
Wodim version: 1.1.9
SCSI buffer size: 64512
Beginning DMA speed test. Set CDR_NODMATEST environment variable if device
communication breaks or freezes immediately after that.
TOC Type: 3 = CD-ROM XA mode 2
Waiting for data on stdin...
Driveropts: 'burnfree'
Device type : Removable CD-ROM
Version : 5
Response Format: 2
Capabilities :
Vendor_info : 'HL-DT-ST'
Identification : 'DVDRAM GSA-T40N '
Revision : 'JP01'
Device seems to be: Generic mmc2 DVD-R/DVD-RW.
Current: 0x0011 (DVD-R sequential recording)
Profile: 0x0012 (DVD-RAM)
Profile: 0x0011 (DVD-R sequential recording) (current)
Profile: 0x0015 (DVD-R/DL sequential recording)
Profile: 0x0016 (DVD-R/DL layer jump recording)
Profile: 0x0014 (DVD-RW sequential recording)
Profile: 0x0013 (DVD-RW restricted overwrite)
Profile: 0x001A (DVD+RW)
Profile: 0x001B (DVD+R)
Profile: 0x002B (DVD+R/DL)
Profile: 0x0010 (DVD-ROM)
Profile: 0x0009 (CD-R)
Profile: 0x000A (CD-RW)
Profile: 0x0008 (CD-ROM)
Profile: 0x0002 (Removable disk)
Using generic SCSI-3/mmc DVD-R(W) driver (mmc_mdvd).
Driver flags : SWABAUDIO BURNFREE
Supported modes: PACKET SAO
Drive buf size : 1114112 = 1088 KB
Drive DMA Speed: 12902 kB/s 73x CD 9x DVD
FIFO size : 4194304 = 4096 KB
Speed set to 5540 KB/s
Track 01: data 1102 MB
Total size: 1265 MB (125:24.69) = 564352 sectors
Lout start: 1266 MB (125:26/52) = 564352 sectors
Current Secsize: 2048
HINT: use dvd+rw-mediainfo from dvd+rw-tools for information extraction.
Blocks total: 2298496 Blocks current: 2298496 Blocks remaining: 1734144
Starting to write CD/DVD at speed 4.0 in dummy SAO mode for multi session.
Last chance to quit, starting dummy write in 2 seconds.
1 seconds.
0 seconds. Operation starts.
Waiting for reader process to fill input buffer ... input buffer ready.
Sending CUE sheet...
Starting new track at sector: 0
Track 01: 0 of 1102 MB written.
Errno: 5 (Input/output error), write_g1 scsi sendcmd: no error
CDB: 2A 00 00 00 00 00 00 00 1F 00
status: 0x2 (CHECK CONDITION)
Sense Bytes: 70 00 03 00 00 00 00 0A 32 4D 03 0C 0C 00 00 00
Sense Key: 0x3 Medium Error, Segment 0
Sense Code: 0x0C Qual 0x00 (write error) Fru 0x0
Sense flags: Blk 0 (not valid)
cmd finished after 28.985s timeout 200s
wodim: A write error occured.
wodim: Please properly read the error message above.
write track data: error after 0 bytes
Writing time: 34.044s
Average write speed 24.6x.
Fixating...
WARNING: Some drives don't like fixation in dummy mode.
Fixating time: 0.012s
wodim: fifo had 64 puts and 1 gets.
wodim: fifo was 0 times empty and 0 times full, min fill was 100%.
cdrecord command:
-----------------------
/usr/bin/cdrecord -v gracetime=2 dev=/dev/sr0 speed=4 -sao -dummy driveropts=burnfree -multi -waiti -xa -tsize=564352s -
