Например, при вызове команды
Код: Выделить всё
root@fw5:~# ip a
Trace/breakpoint trapПри загрузке постоянно проверяется жесткий диск и при конфигурировании сети подвисает минут 5. бывает такое, что при вызове команды
Код: Выделить всё
root@fw5:~# less /var/log/syslogфайл открывается только после нажатия Ctrl+C.
Больше всего волнует именно ошибка Trace/breakpoint trap, из-за чего она появилась и как от нее избавиться я понять и не могу
Код: Выделить всё
root@fw5:~# dmesg
[ 0.000000] Linux version 2.6.24-16-generic (buildd@palmer) (gcc version 4.2.3 (Ubuntu 4.2.3-2ubuntu7)) #1 SMP Thu Apr 10
13:23:42 UTC 2008 (Ubuntu 2.6.24-16.30-generic)
[ 0.000000] BIOS-provided physical RAM map:
[ 0.000000] BIOS-e820: 0000000000000000 - 000000000009fc00 (usable)
[ 0.000000] BIOS-e820: 000000000009fc00 - 00000000000a0000 (reserved)
[ 0.000000] BIOS-e820: 00000000000e0000 - 0000000000100000 (reserved)
[ 0.000000] BIOS-e820: 0000000000100000 - 000000001d135000 (usable)
[ 0.000000] BIOS-e820: 000000001d135000 - 000000001d236000 (ACPI NVS)
[ 0.000000] BIOS-e820: 000000001d236000 - 000000001ddf2000 (usable)
[ 0.000000] BIOS-e820: 000000001ddf2000 - 000000001ddf4000 (reserved)
[ 0.000000] BIOS-e820: 000000001ddf4000 - 000000001de79000 (usable)
[ 0.000000] BIOS-e820: 000000001de79000 - 000000001def7000 (ACPI NVS)
[ 0.000000] BIOS-e820: 000000001def7000 - 000000001def8000 (usable)
[ 0.000000] BIOS-e820: 000000001def8000 - 000000001deff000 (ACPI data)
[ 0.000000] BIOS-e820: 000000001deff000 - 000000001df00000 (usable)
[ 0.000000] BIOS-e820: 00000000fff80000 - 0000000100000000 (reserved)
[ 0.000000] 0MB HIGHMEM available.
[ 0.000000] 479MB LOWMEM available.
[ 0.000000] found SMP MP-table at 000fe200
[ 0.000000] Entering add_active_range(0, 0, 122624) 0 entries of 256 used
[ 0.000000] Zone PFN ranges:
[ 0.000000] DMA 0 -> 4096
[ 0.000000] Normal 4096 -> 122624
[ 0.000000] HighMem 122624 -> 122624
[ 0.000000] Movable zone start PFN for each node
[ 0.000000] early_node_map[1] active PFN ranges
[ 0.000000] 0: 0 -> 122624
[ 0.000000] On node 0 totalpages: 122624
[ 0.000000] DMA zone: 32 pages used for memmap
[ 0.000000] DMA zone: 0 pages reserved
[ 0.000000] DMA zone: 4064 pages, LIFO batch:0
[ 0.000000] Normal zone: 926 pages used for memmap
[ 0.000000] Normal zone: 117602 pages, LIFO batch:31
[ 0.000000] HighMem zone: 0 pages used for memmap
[ 0.000000] Movable zone: 0 pages used for memmap
[ 0.000000] DMI 2.4 present.
[ 0.000000] ACPI: RSDP signature @ 0xC00FE020 checksum 0
[ 0.000000] ACPI: RSDP 000FE020, 0014 (r0 INTEL )
[ 0.000000] ACPI: RSDT 1DEFE038, 002C (r1 INTEL DG965CO 7A 1000013)
[ 0.000000] ACPI: FACP 1DEFD000, 0074 (r1 INTEL DG965CO 7A MSFT 1000013)
[ 0.000000] ACPI: DSDT 1DEF9000, 30F6 (r1 INTEL DG965CO 7A MSFT 1000013)
[ 0.000000] ACPI: FACS 1DEBC000, 0040
[ 0.000000] ACPI: APIC 1DEF8000, 006C (r1 INTEL DG965CO 7A MSFT 1000013)
[ 0.000000] ACPI: PM-Timer IO Port: 0x808
[ 0.000000] ACPI: Local APIC address 0xfee00000
[ 0.000000] ACPI: LAPIC (acpi_id[0x01] lapic_id[0x00] enabled)
[ 0.000000] Processor #0 7:6 APIC version 20
[ 0.000000] ACPI: LAPIC (acpi_id[0x02] lapic_id[0x81] disabled)
[ 0.000000] ACPI: LAPIC (acpi_id[0x03] lapic_id[0x82] disabled)
[ 0.000000] ACPI: LAPIC (acpi_id[0x04] lapic_id[0x83] disabled)
[ 0.000000] ACPI: IOAPIC (id[0x04] address[0xfec00000] gsi_base[0])
[ 0.000000] IOAPIC[0]: apic_id 4, version 20, address 0xfec00000, GSI 0-23
[ 0.000000] ACPI: INT_SRC_OVR (bus 0 bus_irq 0 global_irq 2 dfl dfl)
[ 0.000000] ACPI: INT_SRC_OVR (bus 0 bus_irq 9 global_irq 9 low level)
[ 0.000000] ACPI: IRQ0 used by override.
[ 0.000000] ACPI: IRQ2 used by override.
[ 0.000000] ACPI: IRQ9 used by override.
[ 0.000000] Enabling APIC mode: Flat. Using 1 I/O APICs
[ 0.000000] Using ACPI (MADT) for SMP configuration information
[ 0.000000] Allocating PCI resources starting at 20000000 (gap: 1df00000:e2080000)
[ 0.000000] swsusp: Registered nosave memory region: 000000000009f000 - 00000000000a0000
[ 0.000000] swsusp: Registered nosave memory region: 00000000000a0000 - 00000000000e0000
[ 0.000000] swsusp: Registered nosave memory region: 00000000000e0000 - 0000000000100000
[ 0.000000] swsusp: Registered nosave memory region: 000000001d135000 - 000000001d236000
[ 0.000000] swsusp: Registered nosave memory region: 000000001ddf2000 - 000000001ddf4000
[ 0.000000] swsusp: Registered nosave memory region: 000000001de79000 - 000000001def7000
[ 0.000000] swsusp: Registered nosave memory region: 000000001def8000 - 000000001deff000
[ 0.000000] Built 1 zonelists in Zone order, mobility grouping on. Total pages: 121666
[ 0.000000] Kernel command line: root=UUID=865bc56f-df6d-4cba-bdb3-e936d9171b6d ro quiet splash
[ 0.000000] mapped APIC to ffffb000 (fee00000)
[ 0.000000] mapped IOAPIC to ffffa000 (fec00000)
[ 0.000000] Enabling fast FPU save and restore... done.
[ 0.000000] Enabling unmasked SIMD FPU exception support... done.
[ 0.000000] Initializing CPU#0
[ 0.000000] PID hash table entries: 2048 (order: 11, 8192 bytes)
[ 0.000000] Detected 1200.066 MHz processor.
[ 21.393242] Console: colour VGA+ 80x25
[ 21.393248] console [tty0] enabled
[ 21.393467] Dentry cache hash table entries: 65536 (order: 6, 262144 bytes)
[ 21.393657] Inode-cache hash table entries: 32768 (order: 5, 131072 bytes)
[ 21.404642] Memory: 471972k/490496k available (2157k kernel code, 16056k reserved, 998k data, 364k init, 0k highmem)
[ 21.404652] virtual kernel memory layout:
[ 21.404653] fixmap : 0xfff4b000 - 0xfffff000 ( 720 kB)
[ 21.404655] pkmap : 0xff800000 - 0xffc00000 (4096 kB)
[ 21.404656] vmalloc : 0xde800000 - 0xff7fe000 ( 527 MB)
[ 21.404658] lowmem : 0xc0000000 - 0xddf00000 ( 479 MB)
[ 21.404659] .init : 0xc041b000 - 0xc0476000 ( 364 kB)
[ 21.404661] .data : 0xc031b5a4 - 0xc0414dc4 ( 998 kB)
[ 21.404662] .text : 0xc0100000 - 0xc031b5a4 (2157 kB)
[ 21.404667] Checking if this processor honours the WP bit even in supervisor mode... Ok.
[ 21.404712] SLUB: Genslabs=11, HWalign=64, Order=0-1, MinObjects=4, CPUs=1, Nodes=1
[ 21.484710] Calibrating delay using timer specific routine.. 2401.99 BogoMIPS (lpj=4803991)
[ 21.484741] Security Framework initialized
[ 21.484747] SELinux: Disabled at boot.
[ 21.484763] AppArmor: AppArmor initialized
[ 21.484768] Failure registering capabilities with primary security module.
[ 21.484779] Mount-cache hash table entries: 512
[ 21.484937] CPU: After generic identify, caps: afebfbff 20100000 00000000 00000000 0000e31d 00000000 00000001 00000000
[ 21.484950] monitor/mwait feature present.
[ 21.484952] using mwait in idle threads.
[ 21.484958] CPU: L1 I cache: 32K, L1 D cache: 32K
[ 21.484961] CPU: L2 cache: 512K
[ 21.484965] CPU: After all inits, caps: afebfbff 20100000 00000000 00003940 0000e31d 00000000 00000001 00000000
[ 21.484976] Compat vDSO mapped to ffffe000.
[ 21.484994] Checking 'hlt' instruction... OK.
[ 21.501287] SMP alternatives: switching to UP code
[ 21.503611] Freeing SMP alternatives: 11k freed
[ 21.503767] Early unpacking initramfs... done
[ 22.005104] ACPI: Core revision 20070126
[ 22.005176] ACPI: Looking for DSDT in initramfs... error, file /DSDT.aml not found.
[ 22.019616] CPU0: Intel(R) Celeron(R) CPU 220 @ 1.20GHz stepping 01
[ 22.019650] Total of 1 processors activated (2401.99 BogoMIPS).
[ 22.019756] ENABLING IO-APIC IRQs
[ 22.019935] ..TIMER: vector=0x31 apic1=0 pin1=2 apic2=-1 pin2=-1
[ 22.164579] Brought up 1 CPUs
[ 22.164608] CPU0 attaching sched-domain:
[ 22.164611] domain 0: span 01
[ 22.164614] groups: 01
[ 22.164851] net_namespace: 64 bytes
[ 22.164873] Booting paravirtualized kernel on bare hardware
[ 22.165542] Time: 7:25:31 Date: 12/17/09
[ 22.165579] NET: Registered protocol family 16
[ 22.165879] EISA bus registered
[ 22.165909] ACPI: bus type pci registered
[ 22.168804] PCI: Using configuration type 1
[ 22.168808] Setting up standard PCI resources
[ 22.190431] ACPI: EC: Look up EC in DSDT
[ 22.194238] ACPI: Interpreter enabled
[ 22.194245] ACPI: (supports S0 S1 S4 S5)
[ 22.194262] ACPI: Using IOAPIC for interrupt routing
[ 22.201112] ACPI: PCI Root Bridge [PCI0] (0000:00)
[ 22.202303] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0._PRT]
[ 22.202617] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.P0P1._PRT]
[ 22.210183] ACPI: PCI Interrupt Link [LNKA] (IRQs 3 4 5 7 *10 11 12 14 15)
[ 22.210307] ACPI: PCI Interrupt Link [LNKB] (IRQs 3 4 5 7 *10 11 12 14 15)
[ 22.210425] ACPI: PCI Interrupt Link [LNKC] (IRQs 3 4 5 7 10 *11 12 14 15)
[ 22.210542] ACPI: PCI Interrupt Link [LNKD] (IRQs 3 4 5 7 10 *11 12 14 15)
[ 22.210660] ACPI: PCI Interrupt Link [LNKE] (IRQs 3 4 5 7 10 *11 12 14 15)
[ 22.210776] ACPI: PCI Interrupt Link [LNKF] (IRQs 3 4 5 7 *10 11 12 14 15)
[ 22.210893] ACPI: PCI Interrupt Link [LNKG] (IRQs 3 4 5 7 10 *11 12 14 15)
[ 22.211015] ACPI: PCI Interrupt Link [LNKH] (IRQs 3 4 5 7 *10 11 12 14 15)
[ 22.211198] Linux Plug and Play Support v0.97 (c) Adam Belay
[ 22.211246] pnp: PnP ACPI init
[ 22.211259] ACPI: bus type pnp registered
[ 22.213930] pnp: PnP ACPI: found 11 devices
[ 22.213936] ACPI: ACPI bus type pnp unregistered
[ 22.213942] PnPBIOS: Disabled by ACPI PNP
[ 22.214310] PCI: Using ACPI for IRQ routing
[ 22.214315] PCI: If a device doesn't work, try "pci=routeirq". If it helps, post a report
[ 22.224560] NET: Registered protocol family 8
[ 22.224563] NET: Registered protocol family 20
[ 22.224673] AppArmor: AppArmor Filesystem Enabled
[ 22.228502] Time: tsc clocksource has been installed.
[ 22.236572] system 00:08: ioport range 0x800-0x8fe has been reserved
[ 22.236577] system 00:08: ioport range 0x8ff-0x8ff has been reserved
[ 22.236580] system 00:08: ioport range 0x4d0-0x4d1 has been reserved
[ 22.236584] system 00:08: ioport range 0x4d6-0x4d6 has been reserved
[ 22.236587] system 00:08: ioport range 0x295-0x29e has been reserved
[ 22.236590] system 00:08: ioport range 0x2e8-0x2ef has been reserved
[ 22.236593] system 00:08: ioport range 0x481-0x48f has been reserved
[ 22.236603] system 00:09: iomem range 0x0-0x9ffff could not be reserved
[ 22.236607] system 00:09: iomem range 0xec000-0xfffff could not be reserved
[ 22.236611] system 00:09: iomem range 0x100000-0x1dffffff could not be reserved
[ 22.236617] system 00:09: iomem range 0xe0000000-0xefffffff has been reserved
[ 22.236620] system 00:09: iomem range 0xfec00000-0xfec00fff has been reserved
[ 22.236624] system 00:09: iomem range 0xfee00000-0xfee00fff has been reserved
[ 22.267265] PCI: Bridge: 0000:00:01.0
[ 22.267270] IO window: 1000-1fff
[ 22.267277] MEM window: 2a000000-2a0fffff
[ 22.267282] PREFETCH window: 20000000-27ffffff
[ 22.267288] PCI: Bridge: 0000:00:1f.0
[ 22.267290] IO window: disabled.
[ 22.267296] MEM window: 1e000000-1e0fffff
[ 22.267301] PREFETCH window: disabled.
[ 22.267319] PCI: Setting latency timer of device 0000:00:01.0 to 64
[ 22.267341] PCI: Enabling device 0000:00:1f.0 (0000 -> 0002)
[ 22.267350] PCI: Setting latency timer of device 0000:00:1f.0 to 64
[ 22.267368] NET: Registered protocol family 2
[ 22.304569] IP route cache hash table entries: 4096 (order: 2, 16384 bytes)
[ 22.304834] TCP established hash table entries: 16384 (order: 5, 131072 bytes)
[ 22.304939] TCP bind hash table entries: 16384 (order: 5, 131072 bytes)
[ 22.305036] TCP: Hash tables configured (established 16384 bind 16384)
[ 22.305040] TCP reno registered
[ 22.316660] checking if image is initramfs...<7>Switched to high resolution mode on CPU 0
[ 22.787721] it is
[ 23.296059] Freeing initrd memory: 7707k freed
[ 23.297060] audit: initializing netlink socket (disabled)
[ 23.297082] audit(1261034731.780:1): initialized
[ 23.300173] VFS: Disk quotas dquot_6.5.1
[ 23.300295] Dquot-cache hash table entries: 1024 (order 0, 4096 bytes)
[ 23.300518] io scheduler noop registered
[ 23.300522] io scheduler anticipatory registered
[ 23.300525] io scheduler deadline registered
[ 23.300544] io scheduler cfq registered (default)
[ 23.300582] Boot video device is 0000:01:00.0
[ 23.300749] PCI: Setting latency timer of device 0000:00:1f.0 to 64
[ 23.300806] assign_interrupt_mode Found MSI capability
[ 23.300863] Allocate Port Service[0000:00:1f.0:pcie00]
[ 23.301230] isapnp: Scanning for PnP cards...
[ 23.655012] isapnp: No Plug & Play device found
[ 23.710790] Real Time Clock Driver v1.12ac
[ 23.710934] Serial: 8250/16550 driver $Revision: 1.90 $ 4 ports, IRQ sharing enabled
[ 23.711092] serial8250: ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A
[ 23.712413] 00:0a: ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A
[ 23.713538] RAMDISK driver initialized: 16 RAM disks of 65536K size 1024 blocksize
[ 23.713647] input: Macintosh mouse button emulation as /devices/virtual/input/input0
[ 23.713804] PNP: PS/2 Controller [PNP0303:PS2K,PNP0f03:PS2M] at 0x60,0x64 irq 1,12
[ 23.716588] serio: i8042 KBD port at 0x60,0x64 irq 1
[ 23.716594] serio: i8042 AUX port at 0x60,0x64 irq 12
[ 23.720114] mice: PS/2 mouse device common for all mice
[ 23.720312] EISA: Probing bus 0 at eisa.0
[ 23.720321] Cannot allocate resource for EISA slot 1
[ 23.720324] Cannot allocate resource for EISA slot 2
[ 23.720352] EISA: Detected 0 cards.
[ 23.720356] cpuidle: using governor ladder
[ 23.720358] cpuidle: using governor menu
[ 23.720483] NET: Registered protocol family 1
[ 23.720521] Using IPI No-Shortcut mode
[ 23.720566] registered taskstats version 1
[ 23.720688] Magic number: 5:429:420
[ 23.720803] BIOS EDD facility v0.16 2004-Jun-25, 0 devices found
[ 23.720806] EDD information not available.
[ 23.720982] Freeing unused kernel memory: 364k freed
[ 23.747953] input: AT Translated Set 2 keyboard as /devices/platform/i8042/serio0/input/input1
[ 25.034317] fuse init (API version 7.9)
[ 25.070488] ACPI: Processor [CPU0] (supports 8 throttling states)
[ 25.070508] ACPI Exception (processor_core-0816): AE_NOT_FOUND, Processor Device is not present [20070126]
[ 25.070522] ACPI Exception (processor_core-0816): AE_NOT_FOUND, Processor Device is not present [20070126]
[ 25.070534] ACPI Exception (processor_core-0816): AE_NOT_FOUND, Processor Device is not present [20070126]
[ 25.935405] SCSI subsystem initialized
[ 26.034145] usbcore: registered new interface driver usbfs
[ 26.034182] usbcore: registered new interface driver hub
[ 26.059531] libata version 3.00 loaded.
[ 26.071780] usbcore: registered new device driver usb
[ 26.080724] sis900.c: v1.08.10 Apr. 2 2006
[ 26.080810] ACPI: PCI Interrupt 0000:00:04.0[A] -> GSI 19 (level, low) -> IRQ 16
[ 26.082212] 0000:00:04.0: SiS 900 on Foxconn 661 7MI transceiver found at address 1.
[ 26.093593] 0000:00:04.0: Using transceiver found at address 1 as default
[ 26.096693] eth0: SiS 900 PCI Fast Ethernet at 0x2100, IRQ 16, 00:1c:c0:64:fe:8a
[ 26.115063] 8139cp: 10/100 PCI Ethernet driver v1.3 (Mar 22, 2004)
[ 26.115122] 8139cp 0000:00:06.0: This (id 10ec:8139 rev 10) is not an 8139C+ compatible chip
[ 26.115127] 8139cp 0000:00:06.0: Try the "8139too" driver instead.
[ 26.131165] ACPI: PCI Interrupt 0000:00:05.0[A] -> GSI 17 (level, low) -> IRQ 17
[ 26.131202] ACPI: PCI interrupt for device 0000:00:05.0 disabled
[ 26.140097] ohci_hcd: 2006 August 04 USB 1.1 'Open' Host Controller (OHCI) Driver
[ 26.140152] PCI: Enabling device 0000:00:03.0 (0100 -> 0102)
[ 26.140165] ACPI: PCI Interrupt 0000:00:03.0[A] -> GSI 20 (level, low) -> IRQ 18
[ 26.140187] ohci_hcd 0000:00:03.0: OHCI Host Controller
[ 26.140545] ohci_hcd 0000:00:03.0: new USB bus registered, assigned bus number 1
[ 26.140569] ohci_hcd 0000:00:03.0: irq 18, io mem 0x2a104000
[ 26.160984] 8139too Fast Ethernet driver 0.9.28
[ 26.197174] usb usb1: configuration #1 chosen from 1 choice
[ 26.197210] hub 1-0:1.0: USB hub found
[ 26.197220] hub 1-0:1.0: 3 ports detected
[ 26.299054] PCI: Enabling device 0000:00:03.1 (0100 -> 0102)
[ 26.299070] ACPI: PCI Interrupt 0000:00:03.1[B] -> GSI 21 (level, low) -> IRQ 19
[ 26.299093] ohci_hcd 0000:00:03.1: OHCI Host Controller
[ 26.299129] ohci_hcd 0000:00:03.1: new USB bus registered, assigned bus number 2
[ 26.299148] ohci_hcd 0000:00:03.1: irq 19, io mem 0x2a103000
[ 26.357096] usb usb2: configuration #1 chosen from 1 choice
[ 26.357131] hub 2-0:1.0: USB hub found
[ 26.357142] hub 2-0:1.0: 3 ports detected
[ 26.458986] PCI: Enabling device 0000:00:03.2 (0100 -> 0102)
[ 26.459002] ACPI: PCI Interrupt 0000:00:03.2[C] -> GSI 22 (level, low) -> IRQ 20
[ 26.459025] ohci_hcd 0000:00:03.2: OHCI Host Controller
[ 26.459062] ohci_hcd 0000:00:03.2: new USB bus registered, assigned bus number 3
[ 26.459080] ohci_hcd 0000:00:03.2: irq 20, io mem 0x2a102000
[ 26.517050] usb usb3: configuration #1 chosen from 1 choice
[ 26.517086] hub 3-0:1.0: USB hub found
[ 26.517096] hub 3-0:1.0: 2 ports detected
[ 26.619086] pata_sis 0000:00:02.5: version 0.5.2
[ 26.621616] scsi0 : pata_sis
[ 26.622731] scsi1 : pata_sis
[ 26.623183] ata1: PATA max UDMA/133 cmd 0x1f0 ctl 0x3f6 bmdma 0x2410 irq 14
[ 26.623187] ata2: PATA max UDMA/133 cmd 0x170 ctl 0x376 bmdma 0x2418 irq 15
[ 26.834168] ata1.01: ATA-7: ST380215A, 3.AAC, max UDMA/100
[ 26.834174] ata1.01: 156301488 sectors, multi 16: LBA48
[ 26.900673] ata1.01: configured for UDMA/100
[ 27.054848] scsi 0:0:1:0: Direct-Access ATA ST380215A 3.AA PQ: 0 ANSI: 5
[ 27.057176] ACPI: PCI Interrupt 0000:00:06.0[A] -> GSI 17 (level, low) -> IRQ 17
[ 27.057867] eth1: RealTek RTL8139 at 0x2000, 00:80:48:49:79:be, IRQ 17
[ 27.057871] eth1: Identified 8139 chip type 'RTL-8100B/8139D'
[ 27.057924] PCI: Enabling device 0000:00:03.3 (0100 -> 0102)
[ 27.057934] ACPI: PCI Interrupt 0000:00:03.3[D] -> GSI 23 (level, low) -> IRQ 21
[ 27.057948] ehci_hcd 0000:00:03.3: EHCI Host Controller
[ 27.057993] ehci_hcd 0000:00:03.3: new USB bus registered, assigned bus number 4
[ 27.058050] ehci_hcd 0000:00:03.3: irq 21, io mem 0x2a101000
[ 27.066619] ehci_hcd 0000:00:03.3: USB 2.0 started, EHCI 1.00, driver 10 Dec 2004
[ 27.066773] usb usb4: configuration #1 chosen from 1 choice
[ 27.066807] hub 4-0:1.0: USB hub found
[ 27.066816] hub 4-0:1.0: 8 ports detected
[ 27.171126] sata_sis 0000:00:05.0: version 1.0
[ 27.171147] ACPI: PCI Interrupt 0000:00:05.0[A] -> GSI 17 (level, low) -> IRQ 17
[ 27.171156] sata_sis 0000:00:05.0: Detected SiS 180/181/964 chipset in SATA mode
[ 27.172272] scsi2 : sata_sis
[ 27.173121] scsi3 : sata_sis
[ 27.173196] ata3: SATA max UDMA/133 cmd 0x2428 ctl 0x2434 bmdma 0x2400 irq 17
[ 27.173201] ata4: SATA max UDMA/133 cmd 0x2420 ctl 0x2430 bmdma 0x2408 irq 17
[ 27.482456] ata3: SATA link down (SStatus 0 SControl 300)
[ 27.802329] ata4: SATA link down (SStatus 0 SControl 300)
[ 27.826887] Driver 'sd' needs updating - please use bus_type methods
[ 27.827012] sd 0:0:1:0: [sda] 156301488 512-byte hardware sectors (80026 MB)
[ 27.827029] sd 0:0:1:0: [sda] Write Protect is off
[ 27.827032] sd 0:0:1:0: [sda] Mode Sense: 00 3a 00 00
[ 27.827055] sd 0:0:1:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[ 27.827122] sd 0:0:1:0: [sda] 156301488 512-byte hardware sectors (80026 MB)
[ 27.827135] sd 0:0:1:0: [sda] Write Protect is off
[ 27.827138] sd 0:0:1:0: [sda] Mode Sense: 00 3a 00 00
[ 27.827159] sd 0:0:1:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[ 27.827165] sda: sda1 sda2 < sda5 >
[ 27.872442] sd 0:0:1:0: [sda] Attached SCSI disk
[ 27.880935] sd 0:0:1:0: Attached scsi generic sg0 type 0
[ 28.211967] Attempting manual resume
[ 28.211972] swsusp: Resume From Partition 8:5
[ 28.211975] PM: Checking swsusp image.
[ 28.212194] PM: Resume from disk failed.
[ 28.263191] kjournald starting. Commit interval 5 seconds
[ 28.263200] EXT3-fs warning (device sda1): ext3_clear_journal_err: Filesystem error recorded from previous mount: IO failure
[ 28.263206] EXT3-fs warning (device sda1): ext3_clear_journal_err: Marking fs in need of filesystem check.
[ 28.270282] EXT3-fs: mounted filesystem with ordered data mode.
[ 29.228630] cp[2450]: segfault at 00006e67 eip 080592cf esp bff01d08 error 6
[ 33.042631] pidof uses obsolete (PF_INET,SOCK_PACKET)
[ 33.164313] NET: Registered protocol family 17
[ 33.164764] device eth0 entered promiscuous mode
[ 33.164776] audit(1261034741.652:2): dev=eth0 prom=256 old_prom=0 auid=4294967295
[ 34.785515] cp[2582]: segfault at 00006e67 eip 080592cf esp bfc360c8 error 6
[ 35.752592] parport_pc 00:07: reported by Plug and Play ACPI
[ 35.752648] parport0: PC-style at 0x378 (0x778), irq 7, using FIFO [PCSPP,TRISTATE,COMPAT,ECP]
[ 35.847620] lp0: using parport0 (interrupt-driven).
[ 35.971758] Adding 2265124k swap on /dev/sda5. Priority:-1 extents:1 across:2265124k
[ 386.549598] EXT3 FS on sda1, internal journal
[ 388.268243] Ebtables v2.0 registered
[ 388.358987] Bridge firewalling registered
[ 389.869913] ip_tables: (C) 2000-2006 Netfilter Core Team
[ 390.110133] eth1: link up, 10Mbps, half-duplex, lpa 0x0000
[ 768.850497] NET: Registered protocol family 10
[ 768.850816] lo: Disabled Privacy Extensions
[ 769.297930] nf_conntrack version 0.5.0 (8192 buckets, 32768 max)
[ 771.163108] eth0: Media Link On 100mbps full-duplex
[ 772.916820] No dock devices found.
[ 773.107144] input: Power Button (FF) as /devices/virtual/input/input2
[ 773.117597] ACPI: Power Button (FF) [PWRF]
[ 773.117686] input: Power Button (CM) as /devices/virtual/input/input3
[ 773.129586] ACPI: Power Button (CM) [PWRB]
[ 779.547068] eth0: no IPv6 routers present
[ 779.671016] eth1: no IPv6 routers present
[ 780.033396] apm: BIOS not found.
[ 780.514487] ppdev: user-space parallel port driver
[ 780.823124] audit(1261035493.450:3): type=1503 operation="inode_permission" requested_mask="a::" denied_mask="a::" name="/
dev/tty" pid=6440 profile="/usr/sbin/cupsd" namespace="default"
[ 782.654207] Bluetooth: Core ver 2.11
[ 782.654815] NET: Registered protocol family 31
[ 782.654821] Bluetooth: HCI device and connection manager initialized
[ 782.654826] Bluetooth: HCI socket layer initialized
[ 782.801431] Bluetooth: L2CAP ver 2.9
[ 782.801438] Bluetooth: L2CAP socket layer initialized
[ 782.971051] Bluetooth: RFCOMM socket layer initialized
[ 782.971652] Bluetooth: RFCOMM TTY layer initialized
[ 782.971658] Bluetooth: RFCOMM ver 1.8