Проблемы с ADSL
Модератор: Модераторы разделов
-
Xapdpokep
- Сообщения: 8
- ОС: Xubuntu 9.04
Проблемы с ADSL
риветствую всех! Я вляюсь обладателем usb-модема TP-Link 8817 и Ubuntu 9.10. Проблема заключается в следующем - никак не могу настроить интернет в системе! network applet создаёт подключение eth0, пробует к нему подключиться, но через несколько секунд завершается неудачной попыткой. ping 192.168.1.1 не проходит, говорит, что "network unreached"
-
Xapdpokep
- Сообщения: 8
- ОС: Xubuntu 9.04
Re: Проблемы с ADSL
Код: Выделить всё
lsusb
Bus 001 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub
Bus 002 Device 002: ID 12a7:3160 Trendchip Technologies Corp.
Bus 002 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub
Bus 003 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hubКод: Выделить всё
dmesg
[ 0.000000] lowmem : 0xc0000000 - 0xf77fe000 ( 887 MB)
[ 0.000000] .init : 0xc078e000 - 0xc0815000 ( 540 kB)
[ 0.000000] .data : 0xc0575554 - 0xc078d308 (2143 kB)
[ 0.000000] .text : 0xc0100000 - 0xc0575554 (4565 kB)
[ 0.000000] Checking if this processor honours the WP bit even in supervisor mode...Ok.
[ 0.000000] SLUB: Genslabs=13, HWalign=128, Order=0-3, MinObjects=0, CPUs=4, Nodes=1
[ 0.000000] NR_IRQS:2304 nr_irqs:440
[ 0.000000] Fast TSC calibration using PIT
[ 0.000000] Detected 3000.238 MHz processor.
[ 0.000010] spurious 8259A interrupt: IRQ7.
[ 0.002197] Console: colour VGA+ 80x25
[ 0.002201] console [tty0] enabled
[ 0.004007] Calibrating delay loop (skipped), value calculated using timer frequency.. 6000.47 BogoMIPS (lpj=12000952)
[ 0.004027] Security Framework initialized
[ 0.004046] AppArmor: AppArmor initialized
[ 0.004055] Mount-cache hash table entries: 512
[ 0.004190] Initializing cgroup subsys ns
[ 0.004195] Initializing cgroup subsys cpuacct
[ 0.004200] Initializing cgroup subsys memory
[ 0.004207] Initializing cgroup subsys freezer
[ 0.004210] Initializing cgroup subsys net_cls
[ 0.004230] CPU: Trace cache: 12K uops, L1 D cache: 16K
[ 0.004234] CPU: L2 cache: 2048K
[ 0.004237] CPU: Physical Processor ID: 0
[ 0.004239] CPU: Processor Core ID: 0
[ 0.004244] mce: CPU supports 4 MCE banks
[ 0.004256] CPU0: Thermal monitoring enabled (TM1)
[ 0.004261] using mwait in idle threads.
[ 0.004268] Performance Counters: no PMU driver, software counters only.
[ 0.004275] Checking 'hlt' instruction... OK.
[ 0.023324] ACPI: Core revision 20090521
[ 0.036366] ..TIMER: vector=0x30 apic1=0 pin1=0 apic2=-1 pin2=-1
[ 0.077888] CPU0: Intel(R) Pentium(R) 4 CPU 3.00GHz stepping 02
[ 0.080001] Booting processor 1 APIC 0x1 ip 0x6000
[ 0.004000] Initializing CPU#1
[ 0.004000] Calibrating delay using timer specific routine.. 6000.59 BogoMIPS (lpj=12001192)
[ 0.004000] CPU: Trace cache: 12K uops, L1 D cache: 16K
[ 0.004000] CPU: L2 cache: 2048K
[ 0.004000] CPU: Physical Processor ID: 0
[ 0.004000] CPU: Processor Core ID: 0
[ 0.004000] mce: CPU supports 4 MCE banks
[ 0.004000] CPU1: Thermal monitoring enabled (TM1)
[ 0.004000] x86 PAT enabled: cpu 1, old 0x7040600070406, new 0x7010600070106
[ 0.164986] CPU1: Intel(R) Pentium(R) 4 CPU 3.00GHz stepping 02
[ 0.165008] checking TSC synchronization [CPU#0 -> CPU#1]: passed.
[ 0.168023] Brought up 2 CPUs
[ 0.168028] Total of 2 processors activated (12001.07 BogoMIPS).
[ 0.168080] CPU0 attaching sched-domain:
[ 0.168084] domain 0: span 0-1 level SIBLING
[ 0.168088] groups: 0 1
[ 0.168095] CPU1 attaching sched-domain:
[ 0.168100] domain 0: span 0-1 level SIBLING
[ 0.168103] groups: 1 0
[ 0.168197] Booting paravirtualized kernel on bare hardware
[ 0.168290] regulator: core version 0.5
[ 0.168290] Time: 9:20:32 Date: 01/05/10
[ 0.168290] NET: Registered protocol family 16
[ 0.168290] EISA bus registered
[ 0.168290] ACPI: bus type pci registered
[ 0.168366] PCI: MCFG configuration 0: base e0000000 segment 0 buses 0 - 255
[ 0.168371] PCI: MCFG area at e0000000 reserved in E820
[ 0.168373] PCI: Using MMCONFIG for extended config space
[ 0.168376] PCI: Using configuration type 1 for base access
[ 0.169741] bio: create slab <bio-0> at 0
[ 0.173178] ACPI: EC: Look up EC in DSDT
[ 0.185348] ACPI: Interpreter enabled
[ 0.185358] ACPI: (supports S0 S1 S3 S4 S5)
[ 0.185397] ACPI: Using IOAPIC for interrupt routing
[ 0.198296] ACPI: No dock devices found.
[ 0.198427] ACPI: PCI Root Bridge [PCI0] (0000:00)
[ 0.199002] pci 0000:00:02.0: PME# supported from D0 D1 D2 D3hot D3cold
[ 0.199007] pci 0000:00:02.0: PME# disabled
[ 0.199183] pci 0000:00:0a.1: reg 10 io port: [0xe000-0xe01f]
[ 0.199202] pci 0000:00:0a.1: reg 20 io port: [0x5000-0x503f]
[ 0.199209] pci 0000:00:0a.1: reg 24 io port: [0x5100-0x513f]
[ 0.199231] pci 0000:00:0a.1: PME# supported from D3hot D3cold
[ 0.199236] pci 0000:00:0a.1: PME# disabled
[ 0.199277] pci 0000:00:0b.0: reg 10 32bit mmio: [0xd3000000-0xd3000fff]
[ 0.199318] pci 0000:00:0b.0: supports D1 D2
[ 0.199320] pci 0000:00:0b.0: PME# supported from D0 D1 D2 D3hot D3cold
[ 0.199325] pci 0000:00:0b.0: PME# disabled
[ 0.199356] pci 0000:00:0b.1: reg 10 32bit mmio: [0xd3001000-0xd3001fff]
[ 0.199397] pci 0000:00:0b.1: supports D1 D2
[ 0.199400] pci 0000:00:0b.1: PME# supported from D0 D1 D2 D3hot D3cold
[ 0.199404] pci 0000:00:0b.1: PME# disabled
[ 0.199442] pci 0000:00:0b.2: reg 10 32bit mmio: [0xd3002000-0xd30020ff]
[ 0.199490] pci 0000:00:0b.2: supports D1 D2
[ 0.199493] pci 0000:00:0b.2: PME# supported from D0 D1 D2 D3hot D3cold
[ 0.199498] pci 0000:00:0b.2: PME# disabled
[ 0.199559] pci 0000:00:0f.0: reg 20 io port: [0xf000-0xf00f]
[ 0.199619] pci 0000:00:10.0: reg 10 io port: [0x9f0-0x9f7]
[ 0.199626] pci 0000:00:10.0: reg 14 io port: [0xbf0-0xbf3]
[ 0.199633] pci 0000:00:10.0: reg 18 io port: [0x970-0x977]
[ 0.199640] pci 0000:00:10.0: reg 1c io port: [0xb70-0xb73]
[ 0.199647] pci 0000:00:10.0: reg 20 io port: [0xc800-0xc80f]
[ 0.199654] pci 0000:00:10.0: reg 24 32bit mmio: [0xd3003000-0xd3003fff]
[ 0.199715] pci 0000:00:11.0: reg 10 io port: [0x9e0-0x9e7]
[ 0.199722] pci 0000:00:11.0: reg 14 io port: [0xbe0-0xbe3]
[ 0.199729] pci 0000:00:11.0: reg 18 io port: [0x960-0x967]
[ 0.199736] pci 0000:00:11.0: reg 1c io port: [0xb60-0xb63]
[ 0.199743] pci 0000:00:11.0: reg 20 io port: [0xdc00-0xdc0f]
[ 0.199750] pci 0000:00:11.0: reg 24 32bit mmio: [0xd3004000-0xd3004fff]
[ 0.199866] pci 0000:01:00.0: reg 10 32bit mmio: [0xd0000000-0xd0ffffff]
[ 0.199878] pci 0000:01:00.0: reg 14 64bit mmio: [0xc0000000-0xcfffffff]
[ 0.199889] pci 0000:01:00.0: reg 1c 64bit mmio: [0xd1000000-0xd1ffffff]
[ 0.199901] pci 0000:01:00.0: reg 30 32bit mmio: [0xd2000000-0xd201ffff]
[ 0.199987] pci 0000:00:02.0: bridge 32bit mmio: [0xd0000000-0xd2ffffff]
[ 0.199994] pci 0000:00:02.0: bridge 64bit mmio pref: [0xc0000000-0xcfffffff]
[ 0.200050] pci 0000:02:06.0: reg 10 io port: [0xa000-0xa01f]
[ 0.200101] pci 0000:02:06.0: supports D1 D2
[ 0.200138] pci 0000:02:06.1: reg 10 io port: [0xa400-0xa407]
[ 0.200189] pci 0000:02:06.1: supports D1 D2
[ 0.200240] pci 0000:00:12.0: transparent bridge
[ 0.200244] pci 0000:00:12.0: bridge io port: [0xa000-0xafff]
[ 0.200260] pci_bus 0000:00: on NUMA node 0
[ 0.200268] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0._PRT]
[ 0.200694] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.HUB0._PRT]
[ 0.309136] ACPI: PCI Interrupt Link [LNK1] (IRQs *3 4 5 7 10 11 12 14 15)
[ 0.309341] ACPI: PCI Interrupt Link [LNK2] (IRQs 3 4 5 7 10 11 12 14 15) *0, disabled.
[ 0.309543] ACPI: PCI Interrupt Link [LNK3] (IRQs 3 4 5 7 10 11 12 14 15) *0, disabled.
[ 0.309743] ACPI: PCI Interrupt Link [LNK4] (IRQs 3 4 5 7 10 11 12 14 15) *0, disabled.
[ 0.309944] ACPI: PCI Interrupt Link [LNK5] (IRQs 3 4 5 7 10 11 12 14 15) *0, disabled.
[ 0.310145] ACPI: PCI Interrupt Link [LUBA] (IRQs *3 4 5 7 10 11 12 14 15)
[ 0.310350] ACPI: PCI Interrupt Link [LUBB] (IRQs 3 4 *5 7 10 11 12 14 15)
[ 0.310548] ACPI: PCI Interrupt Link [LMAC] (IRQs 3 4 5 7 10 11 12 14 15) *0, disabled.
[ 0.310747] ACPI: PCI Interrupt Link [LACI] (IRQs 3 4 5 7 10 11 12 14 15) *0, disabled.
[ 0.310946] ACPI: PCI Interrupt Link [LMCI] (IRQs 3 4 5 7 10 11 12 14 15) *0, disabled.
[ 0.311147] ACPI: PCI Interrupt Link [LSMB] (IRQs 3 4 5 7 10 *11 12 14 15)
[ 0.311347] ACPI: PCI Interrupt Link [LUB2] (IRQs 3 4 5 7 10 *11 12 14 15)
[ 0.311546] ACPI: PCI Interrupt Link [LIDE] (IRQs 3 4 5 7 10 11 12 14 15) *0, disabled.
[ 0.311767] ACPI: PCI Interrupt Link [LSID] (IRQs 3 4 5 7 10 *11 12 14 15)
[ 0.311988] ACPI: PCI Interrupt Link [LFID] (IRQs 3 4 *5 7 10 11 12 14 15)
[ 0.312246] ACPI: PCI Interrupt Link [APC1] (IRQs 16) *0
[ 0.312470] ACPI: PCI Interrupt Link [APC2] (IRQs 17) *0, disabled.
[ 0.312692] ACPI: PCI Interrupt Link [APC3] (IRQs 18) *0, disabled.
[ 0.312915] ACPI: PCI Interrupt Link [APC4] (IRQs 19) *0, disabled.
[ 0.313059] ACPI: PCI Interrupt Link [APC5] (IRQs *16), disabled.
[ 0.313293] ACPI: PCI Interrupt Link [APCF] (IRQs 20 21 22 23) *0
[ 0.313528] ACPI: PCI Interrupt Link [APCG] (IRQs 20 21 22 23) *0
[ 0.313762] ACPI: PCI Interrupt Link [APCH] (IRQs 20 21 22 23) *0, disabled.
[ 0.313997] ACPI: PCI Interrupt Link [APCJ] (IRQs 20 21 22 23) *0, disabled.
[ 0.314232] ACPI: PCI Interrupt Link [APCK] (IRQs 20 21 22 23) *0, disabled.
[ 0.314468] ACPI: PCI Interrupt Link [APCS] (IRQs 20 21 22 23) *0
[ 0.314701] ACPI: PCI Interrupt Link [APCL] (IRQs 20 21 22 23) *0
[ 0.314934] ACPI: PCI Interrupt Link [APCZ] (IRQs 20 21 22 23) *0, disabled.
[ 0.315181] ACPI: PCI Interrupt Link [APSI] (IRQs 20 21 22 23) *0
[ 0.315427] ACPI: PCI Interrupt Link [APSJ] (IRQs 20 21 22 23) *0
[ 0.315673] ACPI: PCI Interrupt Link [APCP] (IRQs 20 21 22 23) *0, disabled.
[ 0.315925] SCSI subsystem initialized
[ 0.316029] libata version 3.00 loaded.
[ 0.316077] usbcore: registered new interface driver usbfs
[ 0.316077] usbcore: registered new interface driver hub
[ 0.316085] usbcore: registered new device driver usb
[ 0.316089] ACPI: WMI: Mapper loaded
[ 0.316089] PCI: Using ACPI for IRQ routing
[ 0.328013] Bluetooth: Core ver 2.15
[ 0.328034] NET: Registered protocol family 31
[ 0.328034] Bluetooth: HCI device and connection manager initialized
[ 0.328034] Bluetooth: HCI socket layer initialized
[ 0.328034] NetLabel: Initializing
[ 0.328034] NetLabel: domain hash size = 128
[ 0.328035] NetLabel: protocols = UNLABELED CIPSOv4
[ 0.328051] NetLabel: unlabeled traffic allowed by default
[ 0.340014] pnp: PnP ACPI init
[ 0.340027] ACPI: bus type pnp registered
[ 0.346998] pnp: PnP ACPI: found 16 devices
[ 0.347002] ACPI: ACPI bus type pnp unregistered
[ 0.347008] PnPBIOS: Disabled by ACPI PNP
[ 0.347020] system 00:01: ioport range 0x4000-0x407f has been reserved
[ 0.347025] system 00:01: ioport range 0x4080-0x40ff has been reserved
[ 0.347028] system 00:01: ioport range 0x4400-0x447f has been reserved
[ 0.347034] system 00:01: ioport range 0x4480-0x44ff has been reserved
[ 0.347037] system 00:01: ioport range 0x4800-0x487f has been reserved
[ 0.347041] system 00:01: ioport range 0x4880-0x48ff has been reserved
[ 0.347050] system 00:02: ioport range 0x4d0-0x4d1 has been reserved
[ 0.347054] system 00:02: ioport range 0x800-0x87f has been reserved
[ 0.347057] system 00:02: ioport range 0x290-0x297 has been reserved
[ 0.347060] system 00:02: ioport range 0x880-0x88f has been reserved
[ 0.347074] system 00:0e: iomem range 0xe0000000-0xefffffff has been reserved
[ 0.347082] system 00:0f: iomem range 0xf0000-0xf3fff could not be reserved
[ 0.347086] system 00:0f: iomem range 0xf4000-0xf7fff could not be reserved
[ 0.347089] system 00:0f: iomem range 0xf8000-0xfbfff could not be reserved
[ 0.347093] system 00:0f: iomem range 0xfc000-0xfffff could not be reserved
[ 0.347097] system 00:0f: iomem range 0x3fff0000-0x3fffffff could not be reserved
[ 0.347101] system 00:0f: iomem range 0xffff0000-0xffffffff has been reserved
[ 0.347105] system 00:0f: iomem range 0x0-0x9ffff could not be reserved
[ 0.347108] system 00:0f: iomem range 0x100000-0x3ffeffff could not be reserved
[ 0.347112] system 00:0f: iomem range 0xfec00000-0xfec00fff could not be reserved
[ 0.347116] system 00:0f: iomem range 0xfee00000-0xfee00fff has been reserved
[ 0.381831] AppArmor: AppArmor Filesystem Enabled
[ 0.381874] pci 0000:00:02.0: PCI bridge, secondary bus 0000:01
[ 0.381877] pci 0000:00:02.0: IO window: disabled
[ 0.381883] pci 0000:00:02.0: MEM window: 0xd0000000-0xd2ffffff
[ 0.381888] pci 0000:00:02.0: PREFETCH window: 0x000000c0000000-0x000000cfffffff
[ 0.381895] pci 0000:00:12.0: PCI bridge, secondary bus 0000:02
[ 0.381899] pci 0000:00:12.0: IO window: 0xa000-0xafff
[ 0.381904] pci 0000:00:12.0: MEM window: disabled
[ 0.381908] pci 0000:00:12.0: PREFETCH window: disabled
[ 0.381921] pci 0000:00:02.0: setting latency timer to 64
[ 0.381928] pci 0000:00:12.0: setting latency timer to 64
[ 0.381934] pci_bus 0000:00: resource 0 io: [0x00-0xffff]
[ 0.381937] pci_bus 0000:00: resource 1 mem: [0x000000-0xffffffff]
[ 0.381941] pci_bus 0000:01: resource 1 mem: [0xd0000000-0xd2ffffff]
[ 0.381944] pci_bus 0000:01: resource 2 pref mem [0xc0000000-0xcfffffff]
[ 0.381948] pci_bus 0000:02: resource 0 io: [0xa000-0xafff]
[ 0.381951] pci_bus 0000:02: resource 3 io: [0x00-0xffff]
[ 0.381954] pci_bus 0000:02: resource 4 mem: [0x000000-0xffffffff]
[ 0.382003] NET: Registered protocol family 2
[ 0.382131] IP route cache hash table entries: 32768 (order: 5, 131072 bytes)
[ 0.382543] TCP established hash table entries: 131072 (order: 8, 1048576 bytes)
[ 0.383120] TCP bind hash table entries: 65536 (order: 7, 524288 bytes)
[ 0.383408] TCP: Hash tables configured (established 131072 bind 65536)
[ 0.383411] TCP reno registered
[ 0.383500] NET: Registered protocol family 1
[ 0.383579] Trying to unpack rootfs image as initramfs...
[ 0.632249] Freeing initrd memory: 8009k freed
[ 0.636284] cpufreq-nforce2: No nForce2 chipset.
[ 0.636332] Scanning for low memory corruption every 60 seconds
[ 0.636449] audit: initializing netlink socket (disabled)
[ 0.636468] type=2000 audit(1262683231.636:1): initialized
[ 0.645287] highmem bounce pool size: 64 pages
[ 0.645295] HugeTLB registered 4 MB page size, pre-allocated 0 pages
[ 0.647157] VFS: Disk quotas dquot_6.5.2
[ 0.647248] Dquot-cache hash table entries: 1024 (order 0, 4096 bytes)
[ 0.647988] fuse init (API version 7.12)
[ 0.648112] msgmni has been set to 1731
[ 0.648404] alg: No test for stdrng (krng)
[ 0.648426] io scheduler noop registered
[ 0.648429] io scheduler anticipatory registered
[ 0.648432] io scheduler deadline registered
[ 0.648492] io scheduler cfq registered (default)
[ 0.708063] pci 0000:01:00.0: Boot video device
[ 0.708220] alloc irq_desc for 24 on node -1
[ 0.708223] alloc kstat_irqs on node -1
[ 0.708236] pcieport-driver 0000:00:02.0: irq 24 for MSI/MSI-X
[ 0.708245] pcieport-driver 0000:00:02.0: setting latency timer to 64
[ 0.708342] pci_hotplug: PCI Hot Plug PCI Core version: 0.5
[ 0.708380] pciehp: PCI Express Hot Plug Controller Driver version: 0.4
[ 0.708553] input: Power Button as /devices/LNXSYSTM:00/LNXPWRBN:00/input/input0
[ 0.708558] ACPI: Power Button [PWRF]
[ 0.708627] input: Power Button as /devices/LNXSYSTM:00/device:00/PNP0C0C:00/input/input1
[ 0.708631] ACPI: Power Button [PWRB]
[ 0.708719] fan PNP0C0B:00: registered as cooling_device0
[ 0.708727] ACPI: Fan [FAN] (on)
[ 0.709512] processor LNXCPU:00: registered as cooling_device1
[ 0.709567] processor LNXCPU:01: registered as cooling_device2
[ 0.715532] thermal LNXTHERM:01: registered as thermal_zone0
[ 0.715543] ACPI: Thermal Zone [THRM] (40 C)
[ 0.715631] isapnp: Scanning for PnP cards...
[ 0.909045] Switched to high resolution mode on CPU 1
[ 0.912006] Switched to high resolution mode on CPU 0
[ 1.068661] isapnp: No Plug & Play device found
[ 1.070139] Serial: 8250/16550 driver, 4 ports, IRQ sharing enabled
[ 1.070247] serial8250: ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A
[ 1.070678] 00:08: ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A
[ 1.072102] brd: module loaded
[ 1.072709] loop: module loaded
[ 1.072811] input: Macintosh mouse button emulation as /devices/virtual/input/input2
[ 1.073094] sata_nv 0000:00:10.0: version 3.5
[ 1.073561] ACPI: PCI Interrupt Link [APSI] enabled at IRQ 23
[ 1.073567] alloc irq_desc for 23 on node -1
[ 1.073570] alloc kstat_irqs on node -1
[ 1.073578] sata_nv 0000:00:10.0: PCI INT A -> Link[APSI] -> GSI 23 (level, low) -> IRQ 23
[ 1.073622] sata_nv 0000:00:10.0: setting latency timer to 64
[ 1.073692] scsi0 : sata_nv
[ 1.073802] scsi1 : sata_nv
[ 1.074015] ata1: SATA max UDMA/133 cmd 0x9f0 ctl 0xbf0 bmdma 0xc800 irq 23
[ 1.074019] ata2: SATA max UDMA/133 cmd 0x970 ctl 0xb70 bmdma 0xc808 irq 23
[ 1.074511] ACPI: PCI Interrupt Link [APSJ] enabled at IRQ 22
[ 1.074515] alloc irq_desc for 22 on node -1
[ 1.074518] alloc kstat_irqs on node -1
[ 1.074525] sata_nv 0000:00:11.0: PCI INT A -> Link[APSJ] -> GSI 22 (level, low) -> IRQ 22
[ 1.074564] sata_nv 0000:00:11.0: setting latency timer to 64
[ 1.074622] scsi2 : sata_nv
[ 1.074701] scsi3 : sata_nv
[ 1.074911] ata3: SATA max UDMA/133 cmd 0x9e0 ctl 0xbe0 bmdma 0xdc00 irq 22
[ 1.074915] ata4: SATA max UDMA/133 cmd 0x960 ctl 0xb60 bmdma 0xdc08 irq 22
[ 1.075051] pata_amd 0000:00:0f.0: version 0.4.1
[ 1.075090] pata_amd 0000:00:0f.0: setting latency timer to 64
[ 1.075164] scsi4 : pata_amd
[ 1.075259] ata3: SATA link down (SStatus 0 SControl 300)
[ 1.075263] scsi5 : pata_amd
[ 1.076146] ata5: PATA max UDMA/133 cmd 0x1f0 ctl 0x3f6 bmdma 0xf000 irq 14
[ 1.076151] ata6: PATA max UDMA/133 cmd 0x170 ctl 0x376 bmdma 0xf008 irq 15
[ 1.077183] Fixed MDIO Bus: probed
[ 1.077230] PPP generic driver version 2.4.2
[ 1.077351] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
[ 1.077719] ACPI: PCI Interrupt Link [APCL] enabled at IRQ 21
[ 1.077725] alloc irq_desc for 21 on node -1
[ 1.077727] alloc kstat_irqs on node -1
[ 1.077735] ehci_hcd 0000:00:0b.2: PCI INT C -> Link[APCL] -> GSI 21 (level, low) -> IRQ 21
[ 1.077747] ehci_hcd 0000:00:0b.2: setting latency timer to 64
[ 1.077751] ehci_hcd 0000:00:0b.2: EHCI Host Controller
[ 1.077810] ehci_hcd 0000:00:0b.2: new USB bus registered, assigned bus number 1
[ 1.077842] ehci_hcd 0000:00:0b.2: debug port 1
[ 1.077849] ehci_hcd 0000:00:0b.2: cache line size of 128 is not supported
[ 1.077864] ehci_hcd 0000:00:0b.2: irq 21, io mem 0xd3002000
[ 1.088014] ehci_hcd 0000:00:0b.2: USB 2.0 started, EHCI 1.00
[ 1.088107] usb usb1: configuration #1 chosen from 1 choice
[ 1.088147] hub 1-0:1.0: USB hub found
[ 1.088157] hub 1-0:1.0: 10 ports detected
[ 1.088247] ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver
[ 1.088631] ACPI: PCI Interrupt Link [APCF] enabled at IRQ 20
[ 1.088636] alloc irq_desc for 20 on node -1
[ 1.088639] alloc kstat_irqs on node -1
[ 1.088646] ohci_hcd 0000:00:0b.0: PCI INT A -> Link[APCF] -> GSI 20 (level, low) -> IRQ 20
[ 1.088657] ohci_hcd 0000:00:0b.0: setting latency timer to 64
[ 1.088661] ohci_hcd 0000:00:0b.0: OHCI Host Controller
[ 1.088704] ohci_hcd 0000:00:0b.0: new USB bus registered, assigned bus number 2
[ 1.088730] ohci_hcd 0000:00:0b.0: irq 20, io mem 0xd3000000
[ 1.146073] usb usb2: configuration #1 chosen from 1 choice
[ 1.146112] hub 2-0:1.0: USB hub found
[ 1.146123] hub 2-0:1.0: 5 ports detected
[ 1.146526] ACPI: PCI Interrupt Link [APCG] enabled at IRQ 23
[ 1.146532] ohci_hcd 0000:00:0b.1: PCI INT B -> Link[APCG] -> GSI 23 (level, low) -> IRQ 23
[ 1.146542] ohci_hcd 0000:00:0b.1: setting latency timer to 64
[ 1.146546] ohci_hcd 0000:00:0b.1: OHCI Host Controller
[ 1.146589] ohci_hcd 0000:00:0b.1: new USB bus registered, assigned bus number 3
[ 1.146604] ohci_hcd 0000:00:0b.1: irq 23, io mem 0xd3001000
[ 1.202071] usb usb3: configuration #1 chosen from 1 choice
[ 1.202109] hub 3-0:1.0: USB hub found
[ 1.202120] hub 3-0:1.0: 5 ports detected
[ 1.202191] uhci_hcd: USB Universal Host Controller Interface driver
[ 1.202296] PNP: PS/2 Controller [PNP0303:PS2K,PNP0f13:PS2M] at 0x60,0x64 irq 1,12
[ 1.204964] serio: i8042 KBD port at 0x60,0x64 irq 1
[ 1.204975] serio: i8042 AUX port at 0x60,0x64 irq 12
[ 1.205077] mice: PS/2 mouse device common for all mice
[ 1.205206] rtc_cmos 00:04: RTC can wake from S4
[ 1.205248] rtc_cmos 00:04: rtc core: registered rtc_cmos as rtc0
[ 1.205273] rtc0: alarms up to one year, y3k, 242 bytes nvram
[ 1.205415] device-mapper: uevent: version 1.0.3
[ 1.205527] device-mapper: ioctl: 4.15.0-ioctl (2009-04-01) initialised: dm-devel@redhat.com
[ 1.205631] device-mapper: multipath: version 1.1.0 loaded
[ 1.205636] device-mapper: multipath round-robin: version 1.0.0 loaded
[ 1.205788] EISA: Probing bus 0 at eisa.0
[ 1.205804] Cannot allocate resource for EISA slot 4
[ 1.205806] Cannot allocate resource for EISA slot 5
[ 1.205818] EISA: Detected 0 cards.
[ 1.205940] cpuidle: using governor ladder
[ 1.205946] cpuidle: using governor menu
[ 1.206664] TCP cubic registered
[ 1.206840] NET: Registered protocol family 10
[ 1.207450] lo: Disabled Privacy Extensions
[ 1.207933] NET: Registered protocol family 17
[ 1.207956] Bluetooth: L2CAP ver 2.13
[ 1.207959] Bluetooth: L2CAP socket layer initialized
[ 1.207962] Bluetooth: SCO (Voice Link) ver 0.6
[ 1.207964] Bluetooth: SCO socket layer initialized
[ 1.208010] Bluetooth: RFCOMM TTY layer initialized
[ 1.208015] Bluetooth: RFCOMM socket layer initialized
[ 1.208018] Bluetooth: RFCOMM ver 1.11
[ 1.208053] Using IPI No-Shortcut mode
[ 1.208132] PM: Resume from disk failed.
[ 1.208148] registered taskstats version 1
[ 1.208293] Magic number: 10:566:322
[ 1.208307] tty tty47: hash matches
[ 1.208313] misc mcelog: hash matches
[ 1.208363] rtc_cmos 00:04: setting system clock to 2010-01-05 09:20:33 UTC (1262683233)
[ 1.208367] BIOS EDD facility v0.16 2004-Jun-25, 0 devices found
[ 1.208370] EDD information not available.
[ 1.228029] ata1: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
[ 1.236336] ata1.00: ATA-6: ST3160827AS, 3.42, max UDMA/133
[ 1.236340] ata1.00: 312581808 sectors, multi 1: LBA48 NCQ (depth 0/32)
[ 1.240474] ata5.00: ATAPI: _NEC DVD_RW ND-3550A, 1.05, max UDMA/33
[ 1.240509] ata5: nv_mode_filter: 0x739f&0x739f->0x739f, BIOS=0x7000 (0xc0000000) ACPI=0x701f (60:600:0x13)
[ 1.243804] input: AT Translated Set 2 keyboard as /devices/platform/i8042/serio0/input/input3
[ 1.248476] ata1.00: configured for UDMA/133
[ 1.248604] scsi 0:0:0:0: Direct-Access ATA ST3160827AS 3.42 PQ: 0 ANSI: 5
[ 1.248790] sd 0:0:0:0: Attached scsi generic sg0 type 0
[ 1.248834] sd 0:0:0:0: [sda] 312581808 512-byte logical blocks: (160 GB/149 GiB)
[ 1.248849] ata2: SATA link down (SStatus 0 SControl 300)
[ 1.248923] ata4: SATA link down (SStatus 0 SControl 300)
[ 1.248945] sd 0:0:0:0: [sda] Write Protect is off
[ 1.248952] sd 0:0:0:0: [sda] Mode Sense: 00 3a 00 00
[ 1.248992] sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[ 1.249183] sda:
[ 1.256313] ata5.00: configured for UDMA/33
[ 1.257738] scsi 4:0:0:0: CD-ROM _NEC DVD_RW ND-3550A 1.05 PQ: 0 ANSI: 5
[ 1.260796] sr0: scsi3-mmc drive: 48x/48x writer cd/rw xa/form2 cdda tray
[ 1.260800] Uniform CD-ROM driver Revision: 3.20
[ 1.260897] sr 4:0:0:0: Attached scsi CD-ROM sr0
[ 1.260953] sr 4:0:0:0: Attached scsi generic sg1 type 5
[ 1.261665] sda1 sda2 sda3 sda4
[ 1.286003] sd 0:0:0:0: [sda] Attached SCSI disk
[ 1.427221] Freeing unused kernel memory: 540k freed
[ 1.427610] Write protecting the kernel text: 4568k
[ 1.427668] Write protecting the kernel read-only data: 1836k
[ 1.617681] Floppy drive(s): fd0 is 1.44M
[ 1.642295] FDC 0 is a post-1991 82077
[ 1.700878] usb 2-2: new full speed USB device using ohci_hcd and address 2
[ 1.970090] usb 2-2: configuration #1 chosen from 1 choice
[ 2.751422] xor: automatically using best checksumming function: pIII_sse
[ 2.768008] pIII_sse : 4522.000 MB/sec
[ 2.768012] xor: using function: pIII_sse (4522.000 MB/sec)
[ 2.771181] device-mapper: dm-raid45: initialized v0.2594b
[ 2.925797] PM: Starting manual resume from disk
[ 2.925802] PM: Resume from partition 8:4
[ 2.925804] PM: Checking hibernation image.
[ 2.925972] PM: Resume from disk failed.
[ 2.934488] REISERFS (device sda2): found reiserfs format "3.6" with standard journal
[ 2.934500] REISERFS (device sda2): using ordered data mode
[ 2.947372] REISERFS (device sda2): journal params: device sda2, size 8192, journal first block 18, max trans len 1024, max batch 900, max commit age 30, max trans age 30
[ 2.947702] REISERFS (device sda2): checking transaction log (sda2)
[ 2.973466] REISERFS (device sda2): Using r5 hash to sort names
[ 3.767006] Adding 658656k swap on /dev/sda4. Priority:-1 extents:1 across:658656k
[ 4.160485] udev: starting version 147
[ 5.338375] usbcore: registered new interface driver cdc_ether
[ 5.376254] gameport: EMU10K1 is pci0000:02:06.1/gameport0, io 0xa400, speed 59659kHz
[ 5.393400] gameport: NS558 PnP Gameport is pnp00:0d/gameport0, io 0x201, speed 59659kHz
[ 5.432184] i2c-adapter i2c-0: nForce2 SMBus adapter at 0x5000
[ 5.432232] i2c-adapter i2c-1: nForce2 SMBus adapter at 0x5100
[ 5.438383] parport_pc 00:09: reported by Plug and Play ACPI
[ 5.438440] parport0: PC-style at 0x378 (0x778), irq 7, dma 3 [PCSPP,TRISTATE,COMPAT,ECP,DMA]
[ 5.454731] eth0: register 'rndis_host' at usb-0000:00:0b.0-2, RNDIS device, 00:27:19:cb:40:c5
[ 5.454761] usbcore: registered new interface driver rndis_host
[ 5.468110] ppdev: user-space parallel port driver
[ 5.518749] psmouse serio1: ID: 10 00 64
[ 5.560585] cfg80211: Calling CRDA to update world regulatory domain
[ 5.619703] usbcore: registered new interface driver rndis_wlan
[ 5.772424] lp0: using parport0 (interrupt-driven).
[ 6.046498] input: ImPS/2 Generic Wheel Mouse as /devices/platform/i8042/serio1/input/input4
[ 6.658599] cfg80211: World regulatory domain updated:
[ 6.658604] (start_freq - end_freq @ bandwidth), (max_antenna_gain, max_eirp)
[ 6.658608] (2402000 KHz - 2472000 KHz @ 40000 KHz), (300 mBi, 2000 mBm)
[ 6.658612] (2457000 KHz - 2482000 KHz @ 20000 KHz), (300 mBi, 2000 mBm)
[ 6.658615] (2474000 KHz - 2494000 KHz @ 20000 KHz), (300 mBi, 2000 mBm)
[ 6.658618] (5170000 KHz - 5250000 KHz @ 40000 KHz), (300 mBi, 2000 mBm)
[ 6.658622] (5735000 KHz - 5835000 KHz @ 40000 KHz), (300 mBi, 2000 mBm)
[ 7.050967] ip_tables: (C) 2000-2006 Netfilter Core Team
[ 7.569256] ACPI: PCI Interrupt Link [APC1] enabled at IRQ 16
[ 7.569265] alloc irq_desc for 16 on node -1
[ 7.569271] alloc kstat_irqs on node -1
[ 7.569283] EMU10K1_Audigy 0000:02:06.0: PCI INT A -> Link[APC1] -> GSI 16 (level, low) -> IRQ 16
[ 7.573261] Installing spdif_bug patch: SB Audigy 1 ES [SB0160]
[ 33.173832] REISERFS (device sda3): found reiserfs format "3.6" with standard journal
[ 33.173845] REISERFS (device sda3): using ordered data mode
[ 33.174108] REISERFS (device sda3): journal params: device sda3, size 8192, journal first block 18, max trans len 1024, max batch 900, max commit age 30, max trans age 30
[ 33.174485] REISERFS (device sda3): checking transaction log (sda3)
[ 33.236224] REISERFS (device sda3): Using r5 hash to sort names
[ 42.946782] CPU0 attaching NULL sched-domain.
[ 42.946792] CPU1 attaching NULL sched-domain.
[ 42.960088] CPU0 attaching sched-domain:
[ 42.960094] domain 0: span 0-1 level SIBLING
[ 42.960098] groups: 0 1
[ 42.960104] domain 1: span 0-1 level MC
[ 42.960108] groups: 0-1 (__cpu_power = 2048)
[ 42.960116] CPU1 attaching sched-domain:
[ 42.960119] domain 0: span 0-1 level SIBLING
[ 42.960122] groups: 1 0
[ 42.960127] domain 1: span 0-1 level MC
[ 42.960130] groups: 0-1 (__cpu_power = 2048)
[ 43.347109] CPU0 attaching NULL sched-domain.
[ 43.347117] CPU1 attaching NULL sched-domain.
[ 43.360583] CPU0 attaching sched-domain:
[ 43.360589] domain 0: span 0-1 level SIBLING
[ 43.360594] groups: 0 1
[ 43.360602] CPU1 attaching sched-domain:
[ 43.360605] domain 0: span 0-1 level SIBLING
[ 43.360609] groups: 1 0
[ 46.268062] eth0: no IPv6 routers presentчто не так? :?