Драйвера для сканера и принтера скачаны с оф. сайта http://www.support.xerox.com/go/results.as...;Xtype=download
печать заработала, а вот со сканированием беда, не хочет работать и всё.
Ось debian lenny
Код: Выделить всё
Bus 001 Device 057: ID 0924:4271 XeroxКод: Выделить всё
# lsusb -v
Bus 002 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub
Device Descriptor:
bLength 18
bDescriptorType 1
bcdUSB 1.10
bDeviceClass 9 Hub
bDeviceSubClass 0 Unused
bDeviceProtocol 0 Full speed (or root) hub
bMaxPacketSize0 64
idVendor 0x1d6b Linux Foundation
idProduct 0x0001 1.1 root hub
bcdDevice 2.06
iManufacturer 3 Linux 2.6.26-2-686 uhci_hcd
iProduct 2 UHCI Host Controller
iSerial 1 0000:00:1f.4
bNumConfigurations 1
Configuration Descriptor:
bLength 9
bDescriptorType 2
wTotalLength 25
bNumInterfaces 1
bConfigurationValue 1
iConfiguration 0
bmAttributes 0xe0
Self Powered
Remote Wakeup
MaxPower 0mA
Interface Descriptor:
bLength 9
bDescriptorType 4
bInterfaceNumber 0
bAlternateSetting 0
bNumEndpoints 1
bInterfaceClass 9 Hub
bInterfaceSubClass 0 Unused
bInterfaceProtocol 0 Full speed (or root) hub
iInterface 0
Endpoint Descriptor:
bLength 7
bDescriptorType 5
bEndpointAddress 0x81 EP 1 IN
bmAttributes 3
Transfer Type Interrupt
Synch Type None
Usage Type Data
wMaxPacketSize 0x0002 1x 2 bytes
bInterval 255
Hub Descriptor:
bLength 9
bDescriptorType 41
nNbrPorts 2
wHubCharacteristic 0x000a
No power switching (usb 1.0)
Per-port overcurrent protection
bPwrOn2PwrGood 1 * 2 milli seconds
bHubContrCurrent 0 milli Ampere
DeviceRemovable 0x00
PortPwrCtrlMask 0xff
Hub Port Status:
Port 1: 0000.0100 power
Port 2: 0000.0100 power
Device Status: 0x0003
Self Powered
Remote Wakeup Enabled
Bus 001 Device 057: ID 0924:4271 Xerox
Device Descriptor:
bLength 18
bDescriptorType 1
bcdUSB 2.00
bDeviceClass 0 (Defined at Interface level)
bDeviceSubClass 0
bDeviceProtocol 0
bMaxPacketSize0 64
idVendor 0x0924 Xerox
idProduct 0x4271
bcdDevice 0.01
iManufacturer 2 Xerox Co,.
iProduct 4 WorkCentre 5016/5020
iSerial 5 3317088808
bNumConfigurations 1
Configuration Descriptor:
bLength 9
bDescriptorType 2
wTotalLength 62
bNumInterfaces 2
bConfigurationValue 1
iConfiguration 6 Default Configuration
bmAttributes 0xc0
Self Powered
MaxPower 0mA
Interface Descriptor:
bLength 9
bDescriptorType 4
bInterfaceNumber 0
bAlternateSetting 0
bNumEndpoints 3
bInterfaceClass 255 Vendor Specific Class
bInterfaceSubClass 255 Vendor Specific Subclass
bInterfaceProtocol 0
iInterface 7 Interface#0 [Scan]
Endpoint Descriptor:
bLength 7
bDescriptorType 5
bEndpointAddress 0x01 EP 1 OUT
bmAttributes 2
Transfer Type Bulk
Synch Type None
Usage Type Data
wMaxPacketSize 0x0040 1x 64 bytes
bInterval 0
Endpoint Descriptor:
bLength 7
bDescriptorType 5
bEndpointAddress 0x81 EP 1 IN
bmAttributes 2
Transfer Type Bulk
Synch Type None
Usage Type Data
wMaxPacketSize 0x0040 1x 64 bytes
bInterval 0
Endpoint Descriptor:
bLength 7
bDescriptorType 5
bEndpointAddress 0x82 EP 2 IN
bmAttributes 3
Transfer Type Interrupt
Synch Type None
Usage Type Data
wMaxPacketSize 0x0008 1x 8 bytes
bInterval 100
Interface Descriptor:
bLength 9
bDescriptorType 4
bInterfaceNumber 1
bAlternateSetting 0
bNumEndpoints 2
bInterfaceClass 7 Printer
bInterfaceSubClass 1 Printer
bInterfaceProtocol 2 Bidirectional
iInterface 8 Interface#1 [Print]
Endpoint Descriptor:
bLength 7
bDescriptorType 5
bEndpointAddress 0x03 EP 3 OUT
bmAttributes 2
Transfer Type Bulk
Synch Type None
Usage Type Data
wMaxPacketSize 0x0040 1x 64 bytes
bInterval 0
Endpoint Descriptor:
bLength 7
bDescriptorType 5
bEndpointAddress 0x83 EP 3 IN
bmAttributes 2
Transfer Type Bulk
Synch Type None
Usage Type Data
wMaxPacketSize 0x0040 1x 64 bytes
bInterval 0
Device Qualifier (for other device speed):
bLength 10
bDescriptorType 6
bcdUSB 2.00
bDeviceClass 0 (Defined at Interface level)
bDeviceSubClass 0
bDeviceProtocol 0
bMaxPacketSize0 64
bNumConfigurations 1
Device Status: 0x0001
Self Powered
Bus 001 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub
Device Descriptor:
bLength 18
bDescriptorType 1
bcdUSB 1.10
bDeviceClass 9 Hub
bDeviceSubClass 0 Unused
bDeviceProtocol 0 Full speed (or root) hub
bMaxPacketSize0 64
idVendor 0x1d6b Linux Foundation
idProduct 0x0001 1.1 root hub
bcdDevice 2.06
iManufacturer 3 Linux 2.6.26-2-686 uhci_hcd
iProduct 2 UHCI Host Controller
iSerial 1 0000:00:1f.2
bNumConfigurations 1
Configuration Descriptor:
bLength 9
bDescriptorType 2
wTotalLength 25
bNumInterfaces 1
bConfigurationValue 1
iConfiguration 0
bmAttributes 0xe0
Self Powered
Remote Wakeup
MaxPower 0mA
Interface Descriptor:
bLength 9
bDescriptorType 4
bInterfaceNumber 0
bAlternateSetting 0
bNumEndpoints 1
bInterfaceClass 9 Hub
bInterfaceSubClass 0 Unused
bInterfaceProtocol 0 Full speed (or root) hub
iInterface 0
Endpoint Descriptor:
bLength 7
bDescriptorType 5
bEndpointAddress 0x81 EP 1 IN
bmAttributes 3
Transfer Type Interrupt
Synch Type None
Usage Type Data
wMaxPacketSize 0x0002 1x 2 bytes
bInterval 255
Hub Descriptor:
bLength 9
bDescriptorType 41
nNbrPorts 2
wHubCharacteristic 0x000a
No power switching (usb 1.0)
Per-port overcurrent protection
bPwrOn2PwrGood 1 * 2 milli seconds
bHubContrCurrent 0 milli Ampere
DeviceRemovable 0x00
PortPwrCtrlMask 0xff
Hub Port Status:
Port 1: 0000.0103 power enable connect
Port 2: 0000.0100 power
Device Status: 0x0003
Self Powered
Remote Wakeup EnabledСканер видит
Код: Выделить всё
# sane-find-scanner
# sane-find-scanner will now attempt to detect your scanner. If the
# result is different from what you expected, first make sure your
# scanner is powered up and properly connected to your computer.
# No SCSI scanners found. If you expected something different, make sure that
# you have loaded a kernel SCSI driver for your SCSI adapter.
# Also you need support for SCSI Generic (sg) in your operating system.
# If using Linux, try "modprobe sg".
found USB scanner (vendor=0x0924 [Xerox Co,.], product=0x4271 [WorkCentre 5016/5020]) at libusb:001:057
# Your USB scanner was (probably) detected. It may or may not be supported by
# SANE. Try scanimage -L and read the backend's manpage.
# Not checking for parallel port scanners.
# Most Scanners connected to the parallel port or other proprietary ports
# can't be detected by this program.Но сканировать отказывается в упор
Код: Выделить всё
# scanimage
scanimage: open of device xrwc5020: failed: Access to resource has been deniedВсе действия выполняются от root, соответственно с правами доступа проблем быть не должно.
Ниже вывод scanimage с дебаг-сообщениями
Код: Выделить всё
export SANE_DEBUG_SANEI_USB=128Код: Выделить всё
...
[sanei_usb] sanei_usb_find_devices: vendor=0x04b8, product=0x0121
[sanei_usb] sanei_usb_find_devices: vendor=0x04b8, product=0x0122
[sanei_usb] sanei_usb_find_devices: vendor=0x04b8, product=0x012d
[sanei_usb] sanei_usb_find_devices: vendor=0x04b8, product=0x012f
[sanei_usb] sanei_usb_find_devices: vendor=0x04b8, product=0x0119
[sanei_usb] sanei_usb_find_devices: vendor=0x04b8, product=0x012e
[sanei_usb] sanei_usb_find_devices: vendor=0x04b8, product=0x083f
usb_os_init: Found USB VFS at /dev/bus/usb
usb_os_find_busses: Found 002
usb_os_find_busses: Found 001
usb_os_find_devices: Found 001 on 002
usb_os_find_devices: Found 057 on 001
usb_os_find_devices: Found 001 on 001
error obtaining child information: Inappropriate ioctl for device
usb_os_find_busses: Found 002
usb_os_find_busses: Found 001
usb_os_find_devices: Found 001 on 002
usb_os_find_devices: Found 057 on 001
usb_os_find_devices: Found 001 on 001
error obtaining child information: Inappropriate ioctl for device
USB error: could not set config 1: Device or resource busy
USB error: could not release intf 0: Invalid argument
scanimage: open of device xrwc5020: failed: Access to resource has been denied