Как заставить работать два PCI-Sata контролера?

[qwerta]

Стоит у меня дома старый компьютер (работает как круглосуточная качалка+файлохранилище).Так как сата он не поддерживает поставил я на него PCI контроллер на 2 SATA.
Система стоит на IDE-диске, а через сата подключены подключены два диска по 1Tb. Но место начало заканчиваться и я решил подключить третий диск.
Купил еще один контролер и подцепил еще один винт. И комп перестал загружаться.
Методом тыка было выявлено: если подцепить на любой контролер винт (не важно один или два) то система грузится, А если на два разных контролера то нет.
Grub ругается на stage 1_5, а lilo пишет LIL после чего выскакивает несколько строк заполненые 01.

[Goodvin]

ИМХО, что-то на стыке прерываний (конфликт или нехватка) и возможностей BIOS старой материнки.
Без информации о железе ничего конкретнее сказать нельзя.

Надо смотреть на настройки в BIOS, на то, чего и сколько вообще поддерживает материнка на PCI и т.д. и т.п.

[qwerta]

Фото контроллера SATA

dmesg

Код: Выделить всё

[    0.000000] Initializing cgroup subsys cpu
[    0.000000] Linux version 2.6.26-p3-p3 (2.6.26) (root@IBM) (gcc version 4.4.5 20100728 (prerelease) (Debian 4.4.4-8) ) #1 Wed Aug 25 12:09:27 MSD 2010
[    0.000000] BIOS-provided physical RAM map:
[    0.000000]  BIOS-e820: 0000000000000000 - 00000000000a0000 (usable)
[    0.000000]  BIOS-e820: 00000000000f0000 - 0000000000100000 (reserved)
[    0.000000]  BIOS-e820: 0000000000100000 - 000000000f7f0000 (usable)
[    0.000000]  BIOS-e820: 000000000f7f0000 - 000000000f7f3000 (ACPI NVS)
[    0.000000]  BIOS-e820: 000000000f7f3000 - 000000000f800000 (ACPI data)
[    0.000000]  BIOS-e820: 000000000f800000 - 0000000010000000 (reserved)
[    0.000000]  BIOS-e820: 00000000fec00000 - 0000000100000000 (reserved)
[    0.000000] 247MB LOWMEM available.
[    0.000000] found SMP MP-table at [c00f58c0] 000f58c0
[    0.000000] Entering add_active_range(0, 0, 63472) 0 entries of 256 used
[    0.000000] Zone PFN ranges:
[    0.000000]   DMA             0 ->     4096
[    0.000000]   Normal       4096 ->    63472
[    0.000000] Movable zone start PFN for each node
[    0.000000] early_node_map[1] active PFN ranges
[    0.000000]     0:        0 ->    63472
[    0.000000] On node 0 totalpages: 63472
[    0.000000]   DMA zone: 32 pages used for memmap
[    0.000000]   DMA zone: 0 pages reserved
[    0.000000]   DMA zone: 4064 pages, LIFO batch:0
[    0.000000]   Normal zone: 464 pages used for memmap
[    0.000000]   Normal zone: 58912 pages, LIFO batch:15
[    0.000000]   Movable zone: 0 pages used for memmap
[    0.000000] DMI 2.3 present.
[    0.000000] ACPI: RSDP 000F7340, 0014 (r0 GBT   )
[    0.000000] ACPI: RSDT 0F7F3000, 002C (r1 GBT    AWRDACPI 42302E31 AWRD        0)
[    0.000000] ACPI: FACP 0F7F3040, 0074 (r1 GBT    AWRDACPI 42302E31 AWRD        0)
[    0.000000] ACPI: DSDT 0F7F30C0, 2CD8 (r1 GBT    AWRDACPI     1000 MSFT  100000C)
[    0.000000] ACPI: FACS 0F7F0000, 0040
[    0.000000] ACPI: APIC 0F7F5DC0, 005A (r1 GBT    AWRDACPI 42302E31 AWRD        0)
[    0.000000] ACPI: PM-Timer IO Port: 0x4008
[    0.000000] ACPI: Local APIC address 0xfee00000
[    0.000000] ACPI: LAPIC (acpi_id[0x00] lapic_id[0x00] enabled)
[    0.000000] ACPI: LAPIC_NMI (acpi_id[0xff] dfl dfl lint[0x1])
[    0.000000] ACPI: IOAPIC (id[0x02] address[0xfec00000] gsi_base[0])
[    0.000000] IOAPIC[0]: apic_id 2, version 17, address 0xfec00000, GSI 0-23
[    0.000000] ACPI: INT_SRC_OVR (bus 0 bus_irq 0 global_irq 2 dfl dfl)
[    0.000000] ACPI: INT_SRC_OVR (bus 0 bus_irq 9 global_irq 9 low level)
[    0.000000] ACPI: IRQ0 used by override.
[    0.000000] ACPI: IRQ2 used by override.
[    0.000000] ACPI: IRQ9 used by override.
[    0.000000] Enabling APIC mode:  Flat.  Using 1 I/O APICs
[    0.000000] Using ACPI (MADT) for SMP configuration information
[    0.000000] Allocating PCI resources starting at 20000000 (gap: 10000000:eec00000)
[    0.000000] PM: Registered nosave memory: 00000000000a0000 - 00000000000f0000
[    0.000000] PM: Registered nosave memory: 00000000000f0000 - 0000000000100000
[    0.000000] Built 1 zonelists in Zone order, mobility grouping on.  Total pages: 62976
[    0.000000] Kernel command line: auto BOOT_IMAGE=p3 ro root=305
[    0.000000] mapped APIC to ffffb000 (fee00000)
[    0.000000] mapped IOAPIC to ffffa000 (fec00000)
[    0.000000] Enabling fast FPU save and restore... done.
[    0.000000] Enabling unmasked SIMD FPU exception support... done.
[    0.000000] Initializing CPU#0
[    0.000000] PID hash table entries: 1024 (order: 10, 4096 bytes)
[    0.000000] Detected 1002.287 MHz processor.
[    0.010000] Console: colour VGA+ 80x25
[    0.010000] console [tty0] enabled
[    0.010000] Dentry cache hash table entries: 32768 (order: 5, 131072 bytes)
[    0.010000] Inode-cache hash table entries: 16384 (order: 4, 65536 bytes)
[    0.010000] Memory: 241892k/253888k available (1643k kernel code, 11320k reserved, 719k data, 320k init, 0k highmem)
[    0.010000] virtual kernel memory layout:
[    0.010000]     fixmap  : 0xfffb4000 - 0xfffff000   ( 300 kB)
[    0.010000]     vmalloc : 0xd0000000 - 0xfffb2000   ( 767 MB)
[    0.010000]     lowmem  : 0xc0000000 - 0xcf7f0000   ( 247 MB)
[    0.010000]       .init : 0xc0352000 - 0xc03a2000   ( 320 kB)
[    0.010000]       .data : 0xc029ae0d - 0xc034ec70   ( 719 kB)
[    0.010000]       .text : 0xc0100000 - 0xc029ae0d   (1643 kB)
[    0.010000] Checking if this processor honours the WP bit even in supervisor mode...Ok.
[    0.010000] CPA: page pool initialized 1 of 1 pages preallocated
[    0.160173] Calibrating delay using timer specific routine.. 2006.57 BogoMIPS (lpj=10032891)
[    0.160367] Security Framework initialized
[    0.160443] SELinux:  Disabled at boot.
[    0.160508] Capability LSM initialized
[    0.160594] Mount-cache hash table entries: 512
[    0.160992] Initializing cgroup subsys ns
[    0.161063] Initializing cgroup subsys cpuacct
[    0.161126] Initializing cgroup subsys devices
[    0.161232] CPU: L1 I cache: 16K, L1 D cache: 16K
[    0.161327] CPU: L2 cache: 256K
[    0.161409] CPU: Intel(R) Celeron(TM) CPU                1000MHz stepping 01
[    0.161550] Checking 'hlt' instruction... OK.
[    0.203994] Freeing SMP alternatives: 0k freed
[    0.204060] ACPI: Core revision 20080321
[    0.218387] ENABLING IO-APIC IRQs
[    0.218824] ..TIMER: vector=0x31 apic1=0 pin1=2 apic2=-1 pin2=-1
[    0.320000] net_namespace: 652 bytes
[    0.320000] Booting paravirtualized kernel on bare hardware
[    0.320000] NET: Registered protocol family 16
[    0.320000] EISA bus registered
[    0.320000] ACPI: bus type pci registered
[    0.350000] PCI: PCI BIOS revision 2.10 entry at 0xfaa80, last bus=1
[    0.350000] PCI: Using configuration type 1 for base access
[    0.350000] Setting up standard PCI resources
[    0.360000] ACPI: EC: Look up EC in DSDT
[    0.368248] ACPI: Interpreter enabled
[    0.368341] ACPI: (supports S0 S3 S4 S5)
[    0.368559] ACPI: Using IOAPIC for interrupt routing
[    0.374880] ACPI: PCI Root Bridge [PCI0] (0000:00)
[    0.375415] pci 0000:00:07.4: quirk: region 6000-607f claimed by vt82c686 HW-mon
[    0.375504] pci 0000:00:07.4: quirk: region 5000-500f claimed by vt82c686 SMB
[    0.375850] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0._PRT]
[    0.402015] ACPI: PCI Interrupt Link [LNKA] (IRQs 1 3 4 5 6 7 10 11 *12 14 15)
[    0.402891] ACPI: PCI Interrupt Link [LNKB] (IRQs 1 3 4 5 6 7 10 *11 12 14 15)
[    0.403727] ACPI: PCI Interrupt Link [LNKC] (IRQs 1 3 4 5 6 7 *10 11 12 14 15)
[    0.404562] ACPI: PCI Interrupt Link [LNKD] (IRQs 1 3 4 *5 6 7 10 11 12 14 15)
[    0.405432] Linux Plug and Play Support v0.97 (c) Adam Belay
[    0.405571] pnp: PnP ACPI init
[    0.405657] ACPI: bus type pnp registered
[    0.412624] pnp: PnP ACPI: found 12 devices
[    0.412710] ACPI: ACPI bus type pnp unregistered
[    0.412782] PnPBIOS: Disabled by ACPI PNP
[    0.413542] PCI: Using ACPI for IRQ routing
[    0.414164] ACPI: RTC can wake from S4
[    0.414311] system 00:00: iomem range 0xcc000-0xcffff has been reserved
[    0.414379] system 00:00: iomem range 0xd4800-0xd7fff has been reserved
[    0.414447] system 00:00: iomem range 0xf0000-0xfbfff could not be reserved
[    0.414515] system 00:00: iomem range 0xfc000-0xfffff could not be reserved
[    0.414583] system 00:00: iomem range 0xf7f0000-0xf7fffff could not be reserved
[    0.414669] system 00:00: iomem range 0xffff0000-0xffffffff could not be reserved
[    0.414754] system 00:00: iomem range 0x0-0x9ffff could not be reserved
[    0.414822] system 00:00: iomem range 0x100000-0xf7effff could not be reserved
[    0.414907] system 00:00: iomem range 0xfec00000-0xfec00fff could not be reserved
[    0.414994] system 00:00: iomem range 0xfee00000-0xfee00fff could not be reserved
[    0.415098] system 00:02: ioport range 0x4d0-0x4d1 has been reserved
[    0.446230] PCI: Bridge: 0000:00:01.0
[    0.446296]   IO window: disabled.
[    0.446358]   MEM window: 0xe0000000-0xe2ffffff
[    0.446421]   PREFETCH window: 0x0000000020000000-0x00000000200fffff
[    0.446509] PCI: Setting latency timer of device 0000:00:01.0 to 64
[    0.446570] NET: Registered protocol family 2
[    0.446854] IP route cache hash table entries: 2048 (order: 1, 8192 bytes)
[    0.447401] TCP established hash table entries: 8192 (order: 4, 65536 bytes)
[    0.447814] TCP bind hash table entries: 8192 (order: 3, 32768 bytes)
[    0.448068] TCP: Hash tables configured (established 8192 bind 8192)
[    0.448135] TCP reno registered
[    0.448450] NET: Registered protocol family 1
[    0.448837] checking if image is initramfs... it is
[    0.950092] Switched to high resolution mode on CPU 0
[    1.552402] Freeing initrd memory: 6029k freed
[    1.554796] audit: initializing netlink socket (disabled)
[    1.554943] type=2000 audit(1283109584.550:1): initialized
[    1.555331] Total HugeTLB memory allocated, 0
[    1.555652] VFS: Disk quotas dquot_6.5.1
[    1.555806] Dquot-cache hash table entries: 1024 (order 0, 4096 bytes)
[    1.556022] msgmni has been set to 484
[    1.556547] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 253)
[    1.556641] io scheduler noop registered
[    1.556700] io scheduler anticipatory registered
[    1.556762] io scheduler deadline registered
[    1.556858] io scheduler cfq registered (default)
[    1.556952] PCI: VIA PCI bridge detected.Disabling DAC.
[    1.557022] pci 0000:00:07.0: Enabling VIA external APIC routing
[    1.557146] pci 0000:01:00.0: Boot video device
[    1.558110] isapnp: Scanning for PnP cards...
[    1.915532] isapnp: No Plug & Play device found
[    1.922158] Serial: 8250/16550 driver $Revision: 1.90 $ 4 ports, IRQ sharing enabled
[    1.922555] serial8250: ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A
[    1.922865] serial8250: ttyS1 at I/O 0x2f8 (irq = 3) is a 16550A
[    1.923781] 00:08: ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A
[    1.924219] 00:09: ttyS1 at I/O 0x2f8 (irq = 3) is a 16550A
[    1.928074] brd: module loaded
[    1.928598] PNP: No PS/2 controller found. Probing ports directly.
[    1.929254] serio: i8042 KBD port at 0x60,0x64 irq 1
[    1.929338] serio: i8042 AUX port at 0x60,0x64 irq 12
[    1.929803] mice: PS/2 mouse device common for all mice
[    1.931530] rtc_cmos 00:04: rtc core: registered rtc_cmos as rtc0
[    1.931656] rtc0: alarms up to one year, y3k
[    1.932000] EISA: Probing bus 0 at eisa.0
[    1.932092] Cannot allocate resource for EISA slot 4
[    1.932155] Cannot allocate resource for EISA slot 5
[    1.932217] Cannot allocate resource for EISA slot 6
[    1.932289] EISA: Detected 0 cards.
[    1.932352] cpuidle: using governor ladder
[    1.932413] cpuidle: using governor menu
[    1.932483] No iBFT detected.
[    1.933595] TCP cubic registered
[    1.933659] NET: Registered protocol family 17
[    1.933737] Using IPI Shortcut mode
[    1.934133] registered taskstats version 1
[    1.934542] rtc_cmos 00:04: setting system clock to 2010-08-29 19:19:45 UTC (1283109585)
[    1.935581] Freeing unused kernel memory: 320k freed
[    2.206871] ACPI: ACPI0007:00 is registered as cooling_device0
[    2.902431] No dock devices found.
[    2.951412] SCSI subsystem initialized
[    3.116152] usbcore: registered new interface driver usbfs
[    3.116323] usbcore: registered new interface driver hub
[    3.116519] usbcore: registered new device driver usb
[    3.129581] USB Universal Host Controller Interface driver v3.0
[    3.132237] ACPI: PCI Interrupt Link [LNKD] enabled at IRQ 11
[    3.132329] ACPI: PCI Interrupt 0000:00:07.2[D] -> Link [LNKD] -> GSI 11 (level, low) -> IRQ 11
[    3.132491] uhci_hcd 0000:00:07.2: VIA VLink IRQ fixup, from 5 to 11
[    3.132593] uhci_hcd 0000:00:07.2: UHCI Host Controller
[    3.132988] uhci_hcd 0000:00:07.2: new USB bus registered, assigned bus number 1
[    3.133124] uhci_hcd 0000:00:07.2: irq 11, io base 0x00009400
[    3.133402] usb usb1: configuration #1 chosen from 1 choice
[    3.133536] hub 1-0:1.0: USB hub found
[    3.133611] hub 1-0:1.0: 2 ports detected
[    3.242228] usb usb1: New USB device found, idVendor=1d6b, idProduct=0001
[    3.242322] usb usb1: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[    3.242407] usb usb1: Product: UHCI Host Controller
[    3.242469] usb usb1: Manufacturer: Linux 2.6.26-p3-p3 uhci_hcd
[    3.242533] usb usb1: SerialNumber: 0000:00:07.2
[    3.242703] ACPI: PCI Interrupt 0000:00:07.3[D] -> Link [LNKD] -> GSI 11 (level, low) -> IRQ 11
[    3.242860] uhci_hcd 0000:00:07.3: VIA VLink IRQ fixup, from 5 to 11
[    3.242960] uhci_hcd 0000:00:07.3: UHCI Host Controller
[    3.243080] uhci_hcd 0000:00:07.3: new USB bus registered, assigned bus number 2
[    3.243201] uhci_hcd 0000:00:07.3: irq 11, io base 0x00009800
[    3.243470] usb usb2: configuration #1 chosen from 1 choice
[    3.243598] hub 2-0:1.0: USB hub found
[    3.243676] hub 2-0:1.0: 2 ports detected
[    3.350502] usb usb2: New USB device found, idVendor=1d6b, idProduct=0001
[    3.350595] usb usb2: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[    3.350678] usb usb2: Product: UHCI Host Controller
[    3.350740] usb usb2: Manufacturer: Linux 2.6.26-p3-p3 uhci_hcd
[    3.350804] usb usb2: SerialNumber: 0000:00:07.3
[    3.376168] libata version 3.00 loaded.
[    3.422979] Uniform Multi-Platform E-IDE driver
[    3.423074] ide: Assuming 33MHz system bus speed for PIO modes; override with idebus=xx
[    3.512463] VP_IDE: IDE controller (0x1106:0x0571 rev 0x06) at  PCI slot 0000:00:07.1
[    3.512648] VP_IDE: not 100% native mode: will probe irqs later
[    3.512740] VP_IDE: VIA vt82c686b (rev 40) IDE UDMA100 controller on pci0000:00:07.1
[    3.512842]     ide0: BM-DMA at 0x9000-0x9007
[    3.512920]     ide1: BM-DMA at 0x9008-0x900f
[    3.512984] Probing IDE interface ide0...
[    3.718678] 8139too Fast Ethernet driver 0.9.28
[    3.895170] Floppy drive(s): fd0 is 1.44M
[    3.914687] FDC 0 is a post-1991 82077
[    3.960319] hda: ST3120022A, ATA DISK drive
[    4.680172] hda: host max PIO5 wanted PIO255(auto-tune) selected PIO4
[    4.680488] hda: host side 80-wire cable detection failed, limiting max speed to UDMA33
[    4.680594] hda: UDMA/33 mode selected
[    4.680872] Probing IDE interface ide1...
[    5.280173] ide0 at 0x1f0-0x1f7,0x3f6 on irq 14
[    5.283973] ide1 at 0x170-0x177,0x376 on irq 15
[    5.287220] sata_sil 0000:00:09.0: version 2.3
[    5.287335] ACPI: PCI Interrupt 0000:00:09.0[A] -> GSI 17 (level, low) -> IRQ 17
[    5.287701] scsi0 : sata_sil
[    5.287994] scsi1 : sata_sil
[    5.288124] ata1: SATA max UDMA/100 mmio m512@0xe4400000 tf 0xe4400080 irq 17
[    5.288193] ata2: SATA max UDMA/100 mmio m512@0xe4400000 tf 0xe44000c0 irq 17
[    5.630034] ata1: SATA link down (SStatus 0 SControl 310)
[    5.980017] ata2: SATA link down (SStatus 0 SControl 310)
[    5.980296] ACPI: PCI Interrupt 0000:00:0a.0[A] -> GSI 18 (level, low) -> IRQ 18
[    5.980664] scsi2 : sata_sil
[    5.980902] scsi3 : sata_sil
[    5.981024] ata3: SATA max UDMA/100 mmio m512@0xe4401000 tf 0xe4401080 irq 18
[    5.981093] ata4: SATA max UDMA/100 mmio m512@0xe4401000 tf 0xe44010c0 irq 18
[    6.330036] ata3: SATA link up 1.5 Gbps (SStatus 113 SControl 310)
[    6.350486] ata3.00: ATA-8: Hitachi HDT721010SLA360, ST6OA31B, max UDMA/133
[    6.350554] ata3.00: 1953525168 sectors, multi 16: LBA48 NCQ (depth 0/32)
[    6.390459] ata3.00: configured for UDMA/100
[    6.740025] ata4: SATA link up 1.5 Gbps (SStatus 113 SControl 310)
[    6.780003] ata4.00: ATA-8: ST31000333AS, CC1H, max UDMA/133
[    6.780003] ata4.00: 1953525168 sectors, multi 16: LBA48 NCQ (depth 0/32)
[    6.867616] ata4.00: configured for UDMA/100
[    6.867616] scsi 2:0:0:0: Direct-Access     ATA      Hitachi HDT72101 ST6O PQ: 0 ANSI: 5
[    6.867616] scsi 3:0:0:0: Direct-Access     ATA      ST31000333AS     CC1H PQ: 0 ANSI: 5
[    6.870137] ACPI: PCI Interrupt 0000:00:0d.0[A] -> GSI 17 (level, low) -> IRQ 17
[    6.871158] eth0: RealTek RTL8139 at 0xc400, 00:20:ed:50:fe:a2, IRQ 17
[    6.871227] eth0:  Identified 8139 chip type 'RTL-8100B/8139D'
[    6.880628] 8139cp: 10/100 PCI Ethernet driver v1.3 (Mar 22, 2004)
[    6.918885] hda: max request size: 512KiB
[    6.920674] hda: 234441648 sectors (120034 MB) w/2048KiB Cache, CHS=16383/255/63
[    6.921414] hda: cache flushes supported
[    6.921656]  hda: hda1 hda2 hda3 hda4 < hda5 >
[    6.996279] Driver 'sd' needs updating - please use bus_type methods
[    7.003220] sd 2:0:0:0: [sda] 1953525168 512-byte hardware sectors (1000205 MB)
[    7.003376] sd 2:0:0:0: [sda] Write Protect is off
[    7.003442] sd 2:0:0:0: [sda] Mode Sense: 00 3a 00 00
[    7.003505] sd 2:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[    7.003840] sd 2:0:0:0: [sda] 1953525168 512-byte hardware sectors (1000205 MB)
[    7.003955] sd 2:0:0:0: [sda] Write Protect is off
[    7.004019] sd 2:0:0:0: [sda] Mode Sense: 00 3a 00 00
[    7.004078] sd 2:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[    7.004167]  sda: sda1
[    7.011205] sd 2:0:0:0: [sda] Attached SCSI disk
[    7.011571] sd 3:0:0:0: [sdb] 1953525168 512-byte hardware sectors (1000205 MB)
[    7.011696] sd 3:0:0:0: [sdb] Write Protect is off
[    7.011761] sd 3:0:0:0: [sdb] Mode Sense: 00 3a 00 00
[    7.011825] sd 3:0:0:0: [sdb] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[    7.012053] sd 3:0:0:0: [sdb] 1953525168 512-byte hardware sectors (1000205 MB)
[    7.012168] sd 3:0:0:0: [sdb] Write Protect is off
[    7.012231] sd 3:0:0:0: [sdb] Mode Sense: 00 3a 00 00
[    7.012291] sd 3:0:0:0: [sdb] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[    7.012379]  sdb: sdb1
[    7.023278] sd 3:0:0:0: [sdb] Attached SCSI disk
[    7.464898] PM: Starting manual resume from disk
[    7.505527] ReiserFS: hda5: found reiserfs format "3.6" with standard journal
[    7.505633] ReiserFS: hda5: using ordered data mode
[    7.520703] ReiserFS: hda5: journal params: device hda5, size 8192, journal first block 18, max trans len 1024, max batch 900, max commit age 30, max trans age 30
[    7.527927] ReiserFS: hda5: checking transaction log (hda5)
[    7.583453] ReiserFS: hda5: Using r5 hash to sort names
[    9.238640] udevd version 125 started
[   11.374682] Linux agpgart interface v0.103
[   11.425514] parport_pc: VIA 686A/8231 detected
[   11.425527] parport_pc: probing current configuration
[   11.425551] parport_pc: Current parallel port base: 0x378
[   11.425632] parport0: PC-style at 0x378 (0x778), irq 7 [PCSPP,TRISTATE]
[   11.480129] pci_hotplug: PCI Hot Plug PCI Core version: 0.5
[   11.540431] agpgart: Detected VIA Apollo ProMedia/PLE133Ta chipset
[   11.541336] agpgart: AGP aperture is 4M @ 0xe4000000
[   11.541668] parport_pc: VIA parallel port: io=0x378, irq=7
[   11.584336] shpchp: Standard Hot Plug PCI Controller Driver version: 0.4
[   12.566947] input: PC Speaker as /class/input/input0
[   12.876520] input: Power Button (FF) as /class/input/input1
[   12.920145] ACPI: Power Button (FF) [PWRF]
[   12.920536] input: Power Button (CM) as /class/input/input2
[   12.951991] ACPI: Power Button (CM) [PWRB]
[   12.952344] input: Sleep Button (CM) as /class/input/input3
[   12.982145] ACPI: Sleep Button (CM) [SLPB]
[   13.540879] Error: Driver 'pcspkr' is already registered, aborting...
[   18.077914] Adding 979924k swap on /dev/hda1.  Priority:-1 extents:1 across:979924k
[   24.934112] loop: module loaded
[   26.875491] kjournald starting.  Commit interval 5 seconds
[   26.881520] EXT3 FS on sdb1, internal journal
[   26.881637] EXT3-fs: mounted filesystem with ordered data mode.
[   26.981428] SGI XFS with ACLs, security attributes, realtime, large block numbers, no debug enabled
[   26.984737] SGI XFS Quota Management subsystem
[   27.007972] XFS mounting filesystem sda1
[   27.060007] Ending clean XFS mount for filesystem: sda1
[   28.120652] eth0: link up, 100Mbps, full-duplex, lpa 0x45E1
[   31.215926] fuse init (API version 7.9)
[   34.457687] NET: Registered protocol family 10
[   34.458762] lo: Disabled Privacy Extensions
[   44.660012] eth0: no IPv6 routers present
[  971.567504] ReiserFS: warning: is_tree_node: node level 25859 does not match to the expected one 1
[  971.567614] ReiserFS: hda5: warning: vs-5150: search_by_key: invalid format found in block 3080230. Fsck?
[  971.567710] ReiserFS: hda5: warning: vs-13070: reiserfs_read_locked_inode: i/o failure occurred trying to find stat data of [27346 33442 0x0 SD]
[25993.509885] ata4: exception Emask 0x10 SAct 0x0 SErr 0x10000 action 0xe frozen
[25993.510053] ata4: SError: { PHYRdyChg }
[25993.510144] ata4: hard resetting link
[25998.280068] ata4: SATA link up 1.5 Gbps (SStatus 113 SControl 310)
[25998.427876] ata4.00: configured for UDMA/100
[25998.427949] ata4: EH complete
[25998.457260] sd 3:0:0:0: [sdb] 1953525168 512-byte hardware sectors (1000205 MB)
[25998.457554] sd 3:0:0:0: [sdb] Write Protect is off
[25998.457616] sd 3:0:0:0: [sdb] Mode Sense: 00 3a 00 00
[25998.457679] sd 3:0:0:0: [sdb] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[26037.844441] ata4: exception Emask 0x10 SAct 0x0 SErr 0x10000 action 0xe frozen
[26037.844586] ata4: SError: { PHYRdyChg }
[26037.844687] ata4: hard resetting link
[26042.610086] ata4: SATA link up 1.5 Gbps (SStatus 113 SControl 310)
[26042.757781] ata4.00: configured for UDMA/100
[26042.757851] ata4: EH complete
[26042.780790] sd 3:0:0:0: [sdb] 1953525168 512-byte hardware sectors (1000205 MB)
[26042.780790] sd 3:0:0:0: [sdb] Write Protect is off
[26042.780790] sd 3:0:0:0: [sdb] Mode Sense: 00 3a 00 00
[26042.780790] sd 3:0:0:0: [sdb] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[26048.915775] ata4: exception Emask 0x10 SAct 0x0 SErr 0x10000 action 0xe frozen
[26048.915860] ata4: SError: { PHYRdyChg }
[26048.915917] ata4: hard resetting link
[26053.681133] ata4: SATA link up 1.5 Gbps (SStatus 113 SControl 310)
[26053.808569] ata4.00: configured for UDMA/100
[26053.808652] ata4: EH complete
[26053.841548] sd 3:0:0:0: [sdb] 1953525168 512-byte hardware sectors (1000205 MB)
[26053.841909] sd 3:0:0:0: [sdb] Write Protect is off
[26053.841953] sd 3:0:0:0: [sdb] Mode Sense: 00 3a 00 00
[26053.842057] sd 3:0:0:0: [sdb] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[26072.516636] ata4.00: limiting speed to UDMA/66:PIO4
[26072.516700] ata4: exception Emask 0x10 SAct 0x0 SErr 0x10000 action 0xe frozen
[26072.516759] ata4: SError: { PHYRdyChg }
[26072.516872] ata4: hard resetting link
[26077.280065] ata4: SATA link up 1.5 Gbps (SStatus 113 SControl 310)
[26077.427798] ata4.00: configured for UDMA/66
[26077.427861] ata4: EH complete
[26077.443979] sd 3:0:0:0: [sdb] 1953525168 512-byte hardware sectors (1000205 MB)
[26077.445773] sd 3:0:0:0: [sdb] Write Protect is off
[26077.445812] sd 3:0:0:0: [sdb] Mode Sense: 00 3a 00 00
[26077.476842] sd 3:0:0:0: [sdb] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[26150.351357] ata4: exception Emask 0x10 SAct 0x0 SErr 0x10000 action 0xe frozen
[26150.351499] ata4: SError: { PHYRdyChg }
[26150.351591] ata4: hard resetting link
[26155.120070] ata4: SATA link up 1.5 Gbps (SStatus 113 SControl 310)
[26155.247902] ata4.00: configured for UDMA/66
[26155.247972] ata4: EH complete
[26155.275679] sd 3:0:0:0: [sdb] 1953525168 512-byte hardware sectors (1000205 MB)
[26155.293123] sd 3:0:0:0: [sdb] Write Protect is off
[26155.293123] sd 3:0:0:0: [sdb] Mode Sense: 00 3a 00 00
[26155.320537] sd 3:0:0:0: [sdb] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[26200.047656] ata4: exception Emask 0x10 SAct 0x0 SErr 0x10000 action 0xe frozen
[26200.047791] ata4: SError: { PHYRdyChg }
[26200.047878] ata4: hard resetting link
[26204.810081] ata4: SATA link up 1.5 Gbps (SStatus 113 SControl 310)
[26204.937764] ata4.00: configured for UDMA/66
[26204.937831] ata4: EH complete
[26204.961476] sd 3:0:0:0: [sdb] 1953525168 512-byte hardware sectors (1000205 MB)
[26204.961476] sd 3:0:0:0: [sdb] Write Protect is off
[26204.961476] sd 3:0:0:0: [sdb] Mode Sense: 00 3a 00 00
[26204.961476] sd 3:0:0:0: [sdb] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[26224.531397] ata4: exception Emask 0x10 SAct 0x0 SErr 0x10000 action 0xe frozen
[26224.531544] ata4: SError: { PHYRdyChg }
[26224.531638] ata4: hard resetting link
[26229.300070] ata4: SATA link up 1.5 Gbps (SStatus 113 SControl 310)
[26229.447827] ata4.00: configured for UDMA/66
[26229.447946] ata4: EH complete
[26229.463994] sd 3:0:0:0: [sdb] 1953525168 512-byte hardware sectors (1000205 MB)
[26229.512986] sd 3:0:0:0: [sdb] Write Protect is off
[26229.513052] sd 3:0:0:0: [sdb] Mode Sense: 00 3a 00 00
[26229.513174] sd 3:0:0:0: [sdb] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[26249.241608] ata4.00: limiting speed to UDMA/33:PIO4
[26249.241710] ata4: exception Emask 0x10 SAct 0x0 SErr 0x10000 action 0xe frozen
[26249.241824] ata4: SError: { PHYRdyChg }
[26249.241916] ata4: hard resetting link
[26254.010063] ata4: SATA link up 1.5 Gbps (SStatus 113 SControl 310)
[26254.137848] ata4.00: configured for UDMA/33
[26254.137917] ata4: EH complete
[26254.225832] sd 3:0:0:0: [sdb] 1953525168 512-byte hardware sectors (1000205 MB)
[26254.227197] sd 3:0:0:0: [sdb] Write Protect is off
[26254.227245] sd 3:0:0:0: [sdb] Mode Sense: 00 3a 00 00
[26254.227815] sd 3:0:0:0: [sdb] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[26272.557248] ata4: exception Emask 0x10 SAct 0x0 SErr 0x10000 action 0xe frozen
[26272.557392] ata4: SError: { PHYRdyChg }
[26272.557479] ata4: hard resetting link
[26277.320068] ata4: SATA link up 1.5 Gbps (SStatus 113 SControl 310)
[26277.447748] ata4.00: configured for UDMA/33
[26277.447819] ata4: EH complete
[26277.448043] sd 3:0:0:0: [sdb] 1953525168 512-byte hardware sectors (1000205 MB)
[26277.448136] sd 3:0:0:0: [sdb] Write Protect is off
[26277.448170] sd 3:0:0:0: [sdb] Mode Sense: 00 3a 00 00
[26277.448229] sd 3:0:0:0: [sdb] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[26307.813110] ata4: exception Emask 0x10 SAct 0x0 SErr 0x10000 action 0xe frozen
[26307.813189] ata4: SError: { PHYRdyChg }
[26307.813242] ata4: hard resetting link
[26312.580100] ata4: SATA link up 1.5 Gbps (SStatus 113 SControl 310)
[26312.727806] ata4.00: configured for UDMA/33
[26312.727876] ata4: EH complete
[26312.743648] sd 3:0:0:0: [sdb] 1953525168 512-byte hardware sectors (1000205 MB)
[26312.782352] sd 3:0:0:0: [sdb] Write Protect is off
[26312.782412] sd 3:0:0:0: [sdb] Mode Sense: 00 3a 00 00
[26312.841851] sd 3:0:0:0: [sdb] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[26343.872045] ata4: exception Emask 0x10 SAct 0x0 SErr 0x10000 action 0xe frozen
[26343.872205] ata4: SError: { PHYRdyChg }
[26343.872537] ata4: hard resetting link
[26348.640085] ata4: SATA link up 1.5 Gbps (SStatus 113 SControl 310)
[26348.767798] ata4.00: configured for UDMA/33
[26348.767871] ata4: EH complete
[26348.794026] sd 3:0:0:0: [sdb] 1953525168 512-byte hardware sectors (1000205 MB)
[26348.794187] sd 3:0:0:0: [sdb] Write Protect is off
[26348.794221] sd 3:0:0:0: [sdb] Mode Sense: 00 3a 00 00
[26348.794327] sd 3:0:0:0: [sdb] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[26392.068973] ata4: exception Emask 0x10 SAct 0x0 SErr 0x10000 action 0xe frozen
[26392.069110] ata4: SError: { PHYRdyChg }
[26392.069207] ata4: hard resetting link
[26396.830070] ata4: SATA link up 1.5 Gbps (SStatus 113 SControl 310)
[26396.957735] ata4.00: configured for UDMA/33
[26396.957804] ata4: EH complete
[26396.979583] sd 3:0:0:0: [sdb] 1953525168 512-byte hardware sectors (1000205 MB)
[26397.006672] sd 3:0:0:0: [sdb] Write Protect is off
[26397.006747] sd 3:0:0:0: [sdb] Mode Sense: 00 3a 00 00
[26397.007128] sd 3:0:0:0: [sdb] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[26404.269084] ata4.00: exception Emask 0x10 SAct 0x0 SErr 0x90000 action 0xe frozen
[26404.269231] ata4: SError: { PHYRdyChg 10B8B }
[26404.269305] ata4.00: cmd 25/00:00:af:52:a7/00:01:20:00:00/e0 tag 0 dma 131072 in
[26404.269309]          res ff/ff:ff:ff:ff:ff/ff:ff:ff:ff:ff/ff Emask 0x12 (ATA bus error)
[26404.271007] ata4.00: status: { Busy }
[26404.271067] ata4.00: error: { ICRC UNC IDNF ABRT }
[26404.271165] ata4: hard resetting link
[26409.040069] ata4: SATA link up 1.5 Gbps (SStatus 113 SControl 310)
[26409.187766] ata4.00: configured for UDMA/33
[26409.187879] ata4: EH complete
[26409.215077] sd 3:0:0:0: [sdb] 1953525168 512-byte hardware sectors (1000205 MB)
[26409.227106] sd 3:0:0:0: [sdb] Write Protect is off
[26409.227161] sd 3:0:0:0: [sdb] Mode Sense: 00 3a 00 00
[26409.239037] sd 3:0:0:0: [sdb] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[26618.556630] ata4: exception Emask 0x10 SAct 0x0 SErr 0x10000 action 0xe frozen
[26618.556764] ata4: SError: { PHYRdyChg }
[26618.556852] ata4: hard resetting link
[26623.320065] ata4: SATA link up 1.5 Gbps (SStatus 113 SControl 310)
[26623.447848] ata4.00: configured for UDMA/33
[26623.447916] ata4: EH complete
[26623.470578] sd 3:0:0:0: [sdb] 1953525168 512-byte hardware sectors (1000205 MB)
[26623.470742] sd 3:0:0:0: [sdb] Write Protect is off
[26623.470777] sd 3:0:0:0: [sdb] Mode Sense: 00 3a 00 00
[26623.470841] sd 3:0:0:0: [sdb] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[26629.614230] ata4: exception Emask 0x10 SAct 0x0 SErr 0x10000 action 0xe frozen
[26629.614322] ata4: SError: { PHYRdyChg }
[26629.614384] ata4: hard resetting link
[26634.380058] ata4: SATA link up 1.5 Gbps (SStatus 113 SControl 310)
[26634.507752] ata4.00: configured for UDMA/33
[26634.507818] ata4: EH complete
[26634.536998] sd 3:0:0:0: [sdb] 1953525168 512-byte hardware sectors (1000205 MB)
[26634.548777] sd 3:0:0:0: [sdb] Write Protect is off
[26634.548845] sd 3:0:0:0: [sdb] Mode Sense: 00 3a 00 00
[26634.551398] sd 3:0:0:0: [sdb] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[26647.850445] ata4: exception Emask 0x10 SAct 0x0 SErr 0x10000 action 0xe frozen
[26647.850445] ata4: SError: { PHYRdyChg }
[26647.850445] ata4: hard resetting link
[26652.620080] ata4: SATA link up 1.5 Gbps (SStatus 113 SControl 310)
[26652.737953] ata4.00: configured for UDMA/33
[26652.738023] ata4: EH complete
[26652.754215] sd 3:0:0:0: [sdb] 1953525168 512-byte hardware sectors (1000205 MB)
[26652.758766] sd 3:0:0:0: [sdb] Write Protect is off
[26652.758823] sd 3:0:0:0: [sdb] Mode Sense: 00 3a 00 00
[26652.811486] sd 3:0:0:0: [sdb] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[26667.171520] ata4: exception Emask 0x10 SAct 0x0 SErr 0x10000 action 0xe frozen
[26667.171609] ata4: SError: { PHYRdyChg }
[26667.171666] ata4: hard resetting link
[26671.950081] ata4: SATA link up 1.5 Gbps (SStatus 113 SControl 310)
[26672.097731] ata4.00: configured for UDMA/33
[26672.097798] ata4: EH complete
[26672.122844] sd 3:0:0:0: [sdb] 1953525168 512-byte hardware sectors (1000205 MB)
[26672.137873] sd 3:0:0:0: [sdb] Write Protect is off
[26672.137930] sd 3:0:0:0: [sdb] Mode Sense: 00 3a 00 00
[26672.146043] sd 3:0:0:0: [sdb] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[26702.629069] ata4: exception Emask 0x10 SAct 0x0 SErr 0x10000 action 0xe frozen
[26702.629219] ata4: SError: { PHYRdyChg }
[26702.629318] ata4: hard resetting link
[26707.390073] ata4: SATA link up 1.5 Gbps (SStatus 113 SControl 310)
[26707.517876] ata4.00: configured for UDMA/33
[26707.517944] ata4: EH complete
[26707.555352] sd 3:0:0:0: [sdb] 1953525168 512-byte hardware sectors (1000205 MB)
[26707.571569] sd 3:0:0:0: [sdb] Write Protect is off
[26707.571569] sd 3:0:0:0: [sdb] Mode Sense: 00 3a 00 00
[26707.582103] sd 3:0:0:0: [sdb] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[26718.575692] ata4: exception Emask 0x10 SAct 0x0 SErr 0x10000 action 0xe frozen
[26718.575850] ata4: SError: { PHYRdyChg }
[26718.575943] ata4: hard resetting link
[26723.340121] ata4: SATA link up 1.5 Gbps (SStatus 113 SControl 310)
[26723.467786] ata4.00: configured for UDMA/33
[26723.467905] ata4: EH complete
[26723.497754] sd 3:0:0:0: [sdb] 1953525168 512-byte hardware sectors (1000205 MB)
[26723.497910] sd 3:0:0:0: [sdb] Write Protect is off
[26723.497944] sd 3:0:0:0: [sdb] Mode Sense: 00 3a 00 00
[26723.498007] sd 3:0:0:0: [sdb] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[26732.976848] ata4: exception Emask 0x10 SAct 0x0 SErr 0x10000 action 0xe frozen
[26732.976934] ata4: SError: { PHYRdyChg }
[26732.976993] ata4: hard resetting link
[26737.800072] ata4: SATA link up 1.5 Gbps (SStatus 113 SControl 310)
[26737.927832] ata4.00: configured for UDMA/33
[26737.927895] ata4: EH complete
[26737.943952] sd 3:0:0:0: [sdb] 1953525168 512-byte hardware sectors (1000205 MB)
[26738.031814] sd 3:0:0:0: [sdb] Write Protect is off
[26738.031878] sd 3:0:0:0: [sdb] Mode Sense: 00 3a 00 00
[26738.033256] sd 3:0:0:0: [sdb] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[27349.855006] init_special_inode: bogus i_mode (0)
[27349.855042] ReiserFS: hda5: warning: vs-13075: reiserfs_read_locked_inode: dead inode read from disk [27363 50124 0x0 SD]. This is likely to be race with knfsd. Ignore
[27920.840238] ata4: exception Emask 0x10 SAct 0x0 SErr 0x10000 action 0xe frozen
[27920.840238] ata4: SError: { PHYRdyChg }
[27920.840238] ata4: hard resetting link
[27925.610069] ata4: SATA link up 1.5 Gbps (SStatus 113 SControl 310)
[27925.737840] ata4.00: configured for UDMA/33
[27925.737917] ata4: EH complete
[27925.754220] sd 3:0:0:0: [sdb] 1953525168 512-byte hardware sectors (1000205 MB)
[27925.795569] ata4.00: exception Emask 0x10 SAct 0x0 SErr 0x90000 action 0xe frozen
[27925.795715] ata4: SError: { PHYRdyChg 10B8B }
[27925.795802] ata4.00: cmd 25/00:00:6f:62:c7/00:01:17:00:00/e0 tag 0 dma 131072 in
[27925.795806]          res ff/ff:ff:ff:ff:ff/ff:ff:ff:ff:ff/ff Emask 0x12 (ATA bus error)
[27925.796021] ata4.00: status: { Busy }
[27925.796087] ata4.00: error: { ICRC UNC IDNF ABRT }
[27925.796178] ata4: hard resetting link
[27930.560066] ata4: SATA link up 1.5 Gbps (SStatus 113 SControl 310)
[27930.707971] ata4.00: configured for UDMA/33
[27930.708080] ata4: EH complete
[27930.739872] sd 3:0:0:0: [sdb] Write Protect is off
[27930.739929] sd 3:0:0:0: [sdb] Mode Sense: 00 3a 00 00
[27930.762743] sd 3:0:0:0: [sdb] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[27930.768953] sd 3:0:0:0: [sdb] 1953525168 512-byte hardware sectors (1000205 MB)
[27930.769159] sd 3:0:0:0: [sdb] Write Protect is off
[27930.769196] sd 3:0:0:0: [sdb] Mode Sense: 00 3a 00 00
[27930.769264] sd 3:0:0:0: [sdb] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[27968.604254] ata4: exception Emask 0x10 SAct 0x0 SErr 0x10000 action 0xe frozen
[27968.604626] ata4: SError: { PHYRdyChg }
[27968.604718] ata4: hard resetting link
[27973.390056] ata4: SATA link up 1.5 Gbps (SStatus 113 SControl 310)
[27973.517767] ata4.00: configured for UDMA/33
[27973.517829] ata4: EH complete
[27973.544190] sd 3:0:0:0: [sdb] 1953525168 512-byte hardware sectors (1000205 MB)
[27973.563199] sd 3:0:0:0: [sdb] Write Protect is off
[27973.563199] sd 3:0:0:0: [sdb] Mode Sense: 00 3a 00 00
[27973.591353] sd 3:0:0:0: [sdb] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[28027.830512] ata4: exception Emask 0x10 SAct 0x0 SErr 0x10000 action 0xe frozen
[28027.830652] ata4: SError: { PHYRdyChg }
[28027.830749] ata4: hard resetting link
[28032.600059] ata4: SATA link up 1.5 Gbps (SStatus 113 SControl 310)
[28032.728088] ata4.00: configured for UDMA/33
[28032.728158] ata4: EH complete
[28032.755365] sd 3:0:0:0: [sdb] 1953525168 512-byte hardware sectors (1000205 MB)
[28032.762749] sd 3:0:0:0: [sdb] Write Protect is off
[28032.762803] sd 3:0:0:0: [sdb] Mode Sense: 00 3a 00 00
[28032.806035] sd 3:0:0:0: [sdb] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[28085.305509] ata4: exception Emask 0x10 SAct 0x0 SErr 0x10000 action 0xe frozen
[28085.305592] ata4: SError: { PHYRdyChg }
[28085.305694] ata4: hard resetting link
[28090.070373] ata4: SATA link up 1.5 Gbps (SStatus 113 SControl 310)
[28090.217773] ata4.00: configured for UDMA/33
[28090.217843] ata4: EH complete
[28090.247995] sd 3:0:0:0: [sdb] 1953525168 512-byte hardware sectors (1000205 MB)
[28090.248142] sd 3:0:0:0: [sdb] Write Protect is off
[28090.248176] sd 3:0:0:0: [sdb] Mode Sense: 00 3a 00 00
[28090.248236] sd 3:0:0:0: [sdb] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[28098.893358] ata4: exception Emask 0x10 SAct 0x0 SErr 0x10000 action 0xe frozen
[28098.893505] ata4: SError: { PHYRdyChg }
[28098.893603] ata4: hard resetting link
[28103.660086] ata4: SATA link up 1.5 Gbps (SStatus 113 SControl 310)
[28103.787807] ata4.00: configured for UDMA/33
[28103.787877] ata4: EH complete
[28103.815433] sd 3:0:0:0: [sdb] 1953525168 512-byte hardware sectors (1000205 MB)
[28103.815595] sd 3:0:0:0: [sdb] Write Protect is off
[28103.815629] sd 3:0:0:0: [sdb] Mode Sense: 00 3a 00 00
[28103.815693] sd 3:0:0:0: [sdb] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[28104.594827] ata4: exception Emask 0x10 SAct 0x0 SErr 0x10000 action 0xe frozen
[28104.596221] ata4: SError: { PHYRdyChg }
[28104.596271] ata4: hard resetting link
[28109.360153] ata4: SATA link up 1.5 Gbps (SStatus 113 SControl 310)
[28109.487781] ata4.00: configured for UDMA/33
[28109.487854] ata4: EH complete
[28109.515844] sd 3:0:0:0: [sdb] 1953525168 512-byte hardware sectors (1000205 MB)
[28109.554087] sd 3:0:0:0: [sdb] Write Protect is off
[28109.554158] sd 3:0:0:0: [sdb] Mode Sense: 00 3a 00 00
[28109.584225] sd 3:0:0:0: [sdb] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[28320.449550] ata4: exception Emask 0x10 SAct 0x0 SErr 0x10000 action 0xe frozen
[28320.449699] ata4: SError: { PHYRdyChg }
[28320.449789] ata4: hard resetting link
[28325.210078] ata4: SATA link up 1.5 Gbps (SStatus 113 SControl 310)
[28325.337771] ata4.00: configured for UDMA/33
[28325.337842] ata4: EH complete
[28325.368299] sd 3:0:0:0: [sdb] 1953525168 512-byte hardware sectors (1000205 MB)
[28325.369099] sd 3:0:0:0: [sdb] Write Protect is off
[28325.369139] sd 3:0:0:0: [sdb] Mode Sense: 00 3a 00 00
[28325.447287] sd 3:0:0:0: [sdb] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[47020.579675] ata4.00: exception Emask 0x10 SAct 0x0 SErr 0x10000 action 0xe frozen
[47020.579790] ata4: SError: { PHYRdyChg }
[47020.579906] ata4.00: cmd c8/00:08:2f:8e:ee/00:00:00:00:00/e8 tag 0 dma 4096 in
[47020.579910]          res d0/d0:d0:d0:d0:d0/ff:ff:ff:ff:ff/d0 Emask 0x12 (ATA bus error)
[47020.580135] ata4.00: status: { Busy }
[47020.580194] ata4.00: error: { ICRC UNC IDNF }
[47020.580273] ata4: hard resetting link
[47025.350080] ata4: SATA link up 1.5 Gbps (SStatus 113 SControl 310)
[47025.477906] ata4.00: configured for UDMA/33
[47025.478076] ata4: EH complete
[47025.521778] sd 3:0:0:0: [sdb] 1953525168 512-byte hardware sectors (1000205 MB)
[47025.541174] sd 3:0:0:0: [sdb] Write Protect is off
[47025.541228] sd 3:0:0:0: [sdb] Mode Sense: 00 3a 00 00
[47025.568174] sd 3:0:0:0: [sdb] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA

lspci

Код: Выделить всё

00:00.0 Host bridge: VIA Technologies, Inc. VT8601 [Apollo ProMedia] (rev 05)
00:01.0 PCI bridge: VIA Technologies, Inc. VT8601 [Apollo ProMedia AGP]
00:07.0 ISA bridge: VIA Technologies, Inc. VT82C686 [Apollo Super South] (rev 40)
00:07.1 IDE interface: VIA Technologies, Inc. VT82C586A/B/VT82C686/A/B/VT823x/A/C PIPC Bus Master IDE (rev 06)
00:07.2 USB Controller: VIA Technologies, Inc. VT82xxxxx UHCI USB 1.1 Controller (rev 1a)
00:07.3 USB Controller: VIA Technologies, Inc. VT82xxxxx UHCI USB 1.1 Controller (rev 1a)
00:07.4 Bridge: VIA Technologies, Inc. VT82C686 [Apollo Super ACPI] (rev 40)
00:09.0 RAID bus controller: Silicon Image, Inc. SiI 3512 [SATALink/SATARaid] Serial ATA Controller (rev 01)
00:0a.0 RAID bus controller: Silicon Image, Inc. SiI 3512 [SATALink/SATARaid] Serial ATA Controller (rev 01)
00:0d.0 Ethernet controller: Realtek Semiconductor Co., Ltd. RTL-8139/8139C/8139C+ (rev 10)
01:00.0 VGA compatible controller: Trident Microsystems CyberBlade/i1 (rev 6a)

Материнка старая на 370 сокете miniATX на чипсете VIA

PS фото биос выложу чуть по позже.

[qwerta]

Здесь описание моей материнки.

bios










А вот что происходит при загрузке grub и lilo



Если после загрузки подключить винт то он видится.

[Goodvin]

Вывод dmesg изобилует нехорошими ошибками и варнингами.
Я бы начал с того, что убедился бы наверняка в исправности железа.

Самое простое - проверить методом исключения.
Т.е. проверить работу этих контроллеров и винтов на заведомо исправной материнке.
Проверить работу на этой материнке заведомо исправного контроллера и винта.
Проверить контроллер с заведомо исправными винтами и наоборот.

Кроме того, проверить конфиг загрузчика и как загрузчик "видлит" накопители - не вылезают ли устройства sd* впереди устройств hd*.

[Goodvin]

Купил еще один контролер и подцепил еще один винт. И комп перестал загружаться.

А если оставить новый контроллер, а старый вытащить? Как себя ведет?

Методом тыка было выявлено: если подцепить на любой контролер винт (не важно один или два) то система грузится, А если на два разных контролера то нет.

Попробуйте в такой конфигурации загрузиться в как-нибудь универсального LiveCD (или LiveUSB, если материнка умеет грузиться с USB).
Например, SystemRescueCD.

Grub ругается на stage 1_5, а lilo пишет LIL после чего выскакивает несколько строк заполненые 01.

http://en.wikipedia.org/wiki/LILO_%28boot_...%29#Error_codes


Судя по всему, ломается порядок устройств и загрузчики пытаются лезть не туда, куда надо.
А там, куда они лезут, они не обнаруживают искомый код и валятся с ошибкой.

[qwerta]

Спасибо за советы разобрался.
Виновата оказалась материнка.
Правда стоило подключить к ней мышку, как загрузка чудесным образом стала нормальной.