Agere PCI SoftModem и Mandriva 2006 (траблы)

[qwerty]

Скачал тарбол ltmodem-2.6-alk-8.tar.bz2, собрал модули, подгрузил. Запускаю KPPP , но при соединении пишет NO DIALTONE. В строке инициализации ставил CGI+C0=B8, но не помогает. Помогите в чём проблема?

[estarchak]

minicom -- поможет проверить работоспособность модема.
Дальше поиск поможет найти нужные команды модема.
После этого настраивай KPPP.

[qwerty]

minicom -- поможет проверить работоспособность модема.
Дальше поиск поможет найти нужные команды модема.
После этого настраивай KPPP.

а вообще возможно его завести, а то замучился?
в инете наткнулся на сообщение якобы под мой модем (TFM-PCIV92) есть дрова но .. ненашёл

Кстати модем совсем не пищит... Может я что-то не так делаю?

и вот ещё, при сборке модулей из ltmodem-8.31a10.tar.gz, они собираются, но не грузятся, аля unknown symbol .... Может кто знает в чём проблема?

Строка инициализации конечно же AT+CGI=B8

[estarchak]

AT+CGI=B8

AT+GCI=B8

Завести пробуйте, должно получиться.

[qwerty]

#lspci -vv
00:00.0 Host bridge: Intel Corporation 82845 845 (Brookdale) Chipset Host Bridge (rev 11)
Subsystem: Giga-byte Technology: Unknown device 1a30
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap+ 66Mhz- UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort+ >SERR- <PERR-
Latency: 0
Region 0: Memory at d0000000 (32-bit, prefetchable) [size=128M]
Capabilities: <available only to root>

00:01.0 PCI bridge: Intel Corporation 82845 845 (Brookdale) Chipset AGP Bridge (rev 11) (prog-if 00 [Normal decode])
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR+ FastB2B-
Status: Cap- 66Mhz+ UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 64
Bus: primary=00, secondary=01, subordinate=01, sec-latency=32
Memory behind bridge: e0000000-e1ffffff
Prefetchable memory behind bridge: d8000000-dfffffff
BridgeCtl: Parity- SERR+ NoISA+ VGA+ MAbort- >Reset- FastB2B-

00:1e.0 PCI bridge: Intel Corporation 82801 PCI Bridge (rev 05) (prog-if 00 [Normal decode])
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR+ FastB2B-
Status: Cap- 66Mhz- UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 0
Bus: primary=00, secondary=02, subordinate=02, sec-latency=32
I/O behind bridge: 0000c000-0000cfff
Memory behind bridge: e2000000-e20fffff
BridgeCtl: Parity- SERR+ NoISA+ VGA- MAbort- >Reset- FastB2B-

00:1f.0 ISA bridge: Intel Corporation 82801BA ISA Bridge (LPC) (rev 05)
Control: I/O+ Mem+ BusMaster+ SpecCycle+ MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap- 66Mhz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 0

00:1f.1 IDE interface: Intel Corporation 82801BA IDE U100 (rev 05) (prog-if 80 [Master])
Subsystem: Giga-byte Technology: Unknown device 2442
Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap- 66Mhz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 0
Region 4: I/O ports at f000 [size=16]

00:1f.2 USB Controller: Intel Corporation 82801BA/BAM USB (Hub #1) (rev 05) (prog-if 00 [UHCI])
Subsystem: Giga-byte Technology: Unknown device 2442
Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap- 66Mhz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 0
Interrupt: pin D routed to IRQ 19
Region 4: I/O ports at d000 [size=32]

00:1f.3 SMBus: Intel Corporation 82801BA/BAM SMBus (rev 05)
Subsystem: Giga-byte Technology: Unknown device 2442
Control: I/O+ Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap- 66Mhz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Interrupt: pin B routed to IRQ 12
Region 4: I/O ports at 5000 [size=16]

00:1f.4 USB Controller: Intel Corporation 82801BA/BAM USB (Hub #2) (rev 05) (prog-if 00 [UHCI])
Subsystem: Giga-byte Technology: Unknown device 2442
Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap- 66Mhz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 0
Interrupt: pin C routed to IRQ 23
Region 4: I/O ports at d800 [size=32]

00:1f.5 Multimedia audio controller: Intel Corporation 82801BA/BAM AC'97 Audio (rev 05)
Subsystem: Giga-byte Technology: Unknown device a002
Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap- 66Mhz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 0
Interrupt: pin B routed to IRQ 17
Region 0: I/O ports at dc00 [size=256]
Region 1: I/O ports at e000 [size=64]

01:00.0 VGA compatible controller: nVidia Corporation NV34 [GeForce FX 5200] (rev a1) (prog-if 00 [VGA])
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap+ 66Mhz+ UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 248 (1250ns min, 250ns max)
Interrupt: pin A routed to IRQ 16
Region 0: Memory at e0000000 (32-bit, non-prefetchable) [size=16M]
Region 1: Memory at d8000000 (32-bit, prefetchable) [size=128M]
Expansion ROM at <unassigned> [disabled] [size=128K]
Capabilities: <available only to root>

02:02.0 Ethernet controller: Realtek Semiconductor Co., Ltd. RTL-8139/8139C/8139C+ (rev 10)
Subsystem: D-Link System Inc DFE-538TX
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap+ 66Mhz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 32 (8000ns min, 16000ns max)
Interrupt: pin A routed to IRQ 22
Region 0: I/O ports at c000 [size=256]
Region 1: Memory at e2000000 (32-bit, non-prefetchable) [size=256]
Capabilities: <available only to root>

02:03.0 Communication controller: Agere Systems V.92 56K WinModem (rev 03)
Subsystem: Agere Systems: Unknown device 044c
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap+ 66Mhz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 32 (63000ns min, 3500ns max)
Interrupt: pin A routed to IRQ 10
Region 0: Memory at e2001000 (32-bit, non-prefetchable) [size=256]
Region 1: I/O ports at c400 [size=8]
Region 2: I/O ports at c800 [size=256]
Capabilities: <available only to root>

#wdialconf /etc/wvdial.conf
Scanning your serial ports for a modem.

Port Scan<*1>: Scanning ttyLTM0 first, /dev/modem is a link to it.
ttyLTM0<*1>: ATQ0 V1 E1 -- OK
ttyLTM0<*1>: ATQ0 V1 E1 Z -- OK
ttyLTM0<*1>: ATQ0 V1 E1 S0=0 -- OK
ttyLTM0<*1>: ATQ0 V1 E1 S0=0 &C1 -- OK
ttyLTM0<*1>: ATQ0 V1 E1 S0=0 &C1 &D2 -- OK
ttyLTM0<*1>: ATQ0 V1 E1 S0=0 &C1 &D2 +FCLASS=0 -- OK
ttyLTM0<*1>: Modem Identifier: ATI -- LT V.92 Data+Fax Modem Version 8.30
ttyLTM0<*1>: Speed 4800: AT -- OK
ttyLTM0<*1>: Speed 9600: AT -- OK
ttyLTM0<*1>: Speed 19200: AT -- OK
ttyLTM0<*1>: Speed 38400: AT -- OK
ttyLTM0<*1>: Speed 57600: AT -- OK
ttyLTM0<*1>: Speed 115200: AT -- OK
ttyLTM0<*1>: Max speed is 115200; that should be safe.
ttyLTM0<*1>: ATQ0 V1 E1 S0=0 &C1 &D2 +FCLASS=0 -- OK
ttyS0<*1>: ATQ0 V1 E1 -- failed with 2400 baud, next try: 9600 baud
ttyS0<*1>: ATQ0 V1 E1 -- failed with 9600 baud, next try: 115200 baud
ttyS0<*1>: ATQ0 V1 E1 -- and failed too at 115200, giving up.
ttyS1<*1>: ATQ0 V1 E1 -- failed with 2400 baud, next try: 9600 baud
ttyS1<*1>: ATQ0 V1 E1 -- failed with 9600 baud, next try: 115200 baud
ttyS1<*1>: ATQ0 V1 E1 -- and failed too at 115200, giving up.
Port Scan<*1>: S2 S3 S4 S5 S6 S7

Found a modem on /dev/ttyLTM0, using link /dev/modem in config.
Modem configuration written to /etc/wvdial.conf.
ttyLTM0<Info>: Speed 115200; init "ATQ0 V1 E1 S0=0 &C1 &D2 +FCLASS=0"

#wvdial
--> WvDial: Internet dialer version 1.54.0
--> Initializing modem.
--> Sending: ATZ
ATZ
OK
--> Sending: ATQ0 V1 E1 S0=0 &C1 &D2 +FCLASS=0
ATQ0 V1 E1 S0=0 &C1 &D2 +FCLASS=0
OK
--> Sending: AT+GCI=B8
AT+GCI=B8
OK
--> Sending: ATH1
ATH1
OK
--> Modem initialized.
--> Sending: ATDT22679
--> Waiting for carrier.
ATDT22679
NO DIALTONE
--> No dial tone.
--> Disconnecting at Mon Jul 17 22:58:44 2006

вот что получилось, может кто подскажет как это побороть? (сорри за длинный пост).

Пробывал собирать дрова 8.31b . собираются с Warning`ами и потом пищат что undefined symbol....
Совсем запарился....