Беспроводная карта wl-2054g (помогите настроить)

[alektop]

Добрый день! Имеется беспроводная карта pheenet 2054g... Необходимо настроить ее под линукс. Карта на основе чипсета Prism Gt. Под винду карта работает под драйерами PRISMA00.sys, PRISM02.sys, и PRISM03.sys. В линуксе я только начинающий.
Под винду карта работает нормально, однако под линукс она вообще не определяется, т.е lspci вообще не выдает никакой информации об этой карте. Поискав по нету я нашел, что вроде как можно запустить подобные карты через ndiswrapper... Соотвественно установил виндовые дрова этой прогой, все вроде бы прошло удачно, однако карта все еще никак не определяется. Я так понимаю надо связать эту карту с этими драйверами. Как это сделать?
Заранее спасибо за помощь.

Да забыл. Дистрибутив линукс kanotix, основанный debian 2.6.11
пробовал на суси 10.1 и мандрива 2006 тоже самое.

[Кто-то]

у меня карточка тоже на чипсете Prism.
завелась с пол пинка - перекомпилируй ядро с поддержкой Prism чипсетов и нужно с prism54.org скачать firmware.

а то, что не показывается в lspci - странно!
покажи вывод dmesg

[alektop]

В ядре поддержка призма вроде бы включена. Как это проверить? Просто линукс не видит карту. Возможно ли вручную указать что данному устройству нужны данные дрова?

Вывод lspci:

0000:00:00.0 Host bridge: Intel Corp. Mobile Memory Controller Hub (rev 03)
0000:00:02.0 VGA compatible controller: Intel Corp. Mobile Graphics Controller (rev 03)
0000:00:02.1 Display controller: Intel Corp. Mobile Graphics Controller (rev 03)
0000:00:1d.0 USB Controller: Intel Corp. 82801FB/FBM/FR/FW/FRW (ICH6 Family) USB UHCI #1 (rev 03)
0000:00:1d.1 USB Controller: Intel Corp. 82801FB/FBM/FR/FW/FRW (ICH6 Family) USB UHCI #2 (rev 03)
0000:00:1d.2 USB Controller: Intel Corp. 82801FB/FBM/FR/FW/FRW (ICH6 Family) USB UHCI #3 (rev 03)
0000:00:1d.3 USB Controller: Intel Corp. 82801FB/FBM/FR/FW/FRW (ICH6 Family) USB UHCI #4 (rev 03)
0000:00:1d.7 USB Controller: Intel Corp. 82801FB/FBM/FR/FW/FRW (ICH6 Family) USB2 EHCI Controller (rev 03)
0000:00:1e.0 PCI bridge: Intel Corp. 82801 PCI Bridge (rev d3)
0000:00:1e.2 Multimedia audio controller: Intel Corp. 82801FB/FBM/FR/FW/FRW (ICH6 Family) AC'97 AudioController (rev 03)
0000:00:1e.3 Modem: Intel Corp. 82801FB/FBM/FR/FW/FRW (ICH6 Family) AC'97 Modem Controller (rev 03)
0000:00:1f.0 ISA bridge: Intel Corp. 82801FBM (ICH6M) LPC Interface Bridge (rev 03)
0000:00:1f.1 IDE interface: Intel Corp. 82801FB/FBM/FR/FW/FRW (ICH6 Family) IDE Controller (rev 03)
0000:00:1f.3 SMBus: Intel Corp. 82801FB/FBM/FR/FW/FRW (ICH6 Family) SMBus Controller (rev 03)
0000:06:05.0 Network controller: Intel Corp. PRO/Wireless 2200BG (rev 05)
0000:06:07.0 Ethernet controller: Realtek Semiconductor Co., Ltd. RTL-8139/8139C/8139C+ (rev 10)
0000:06:09.0 CardBus bridge: ENE Technology Inc CB1410 Cardbus Controller (rev 01)


вывод dmesg:
OVR (bus 0 bus_irq 0 global_irq 2 dfl dfl)
ACPI: INT_SRC_OVR (bus 0 bus_irq 9 global_irq 9 high level)
ACPI: IRQ0 used by override.
ACPI: IRQ2 used by override.
ACPI: IRQ9 used by override.
Enabling APIC mode: Flat. Using 1 I/O APICs
Using ACPI (MADT) for SMP configuration information
Allocating PCI resources starting at 10000000 (gap: 10000000:d0000000)
Built 1 zonelists
Kernel command line: ramdisk_size=100000 init=/etc/init lang=us splash psmouse.proto=imps dma nodhcp noapm noagp screen=1024x768 vga=791 initrd=miniroot.gz nowheelmouse nomce quiet BOOT_IMAGE=knoppix BOOT_IMAGE=vmlinuz
__iounmap: bad address c00fffd9
mapped APIC to ffffd000 (fee00000)
mapped IOAPIC to ffffc000 (fec00000)
Initializing CPU#0
PID hash table entries: 1024 (order: 10, 16384 bytes)
Detected 1696.069 MHz processor.
Using pmtmr for high-res timesource
Console: colour dummy device 80x25
Dentry cache hash table entries: 32768 (order: 5, 131072 bytes)
Inode-cache hash table entries: 16384 (order: 4, 65536 bytes)
Memory: 244232k/252800k available (2717k kernel code, 8040k reserved, 1163k data, 288k init, 0k highmem)
Checking if this processor honours the WP bit even in supervisor mode... Ok.
Calibrating delay loop... 3342.33 BogoMIPS (lpj=1671168)
Mount-cache hash table entries: 512 (order: 0, 4096 bytes)
CPU: After generic identify, caps: afe9fbff 00100000 00000000 00000000 00000180 00000000 00000000
CPU: After vendor identify, caps: afe9fbff 00100000 00000000 00000000 00000180 00000000 00000000
CPU: L1 I cache: 32K, L1 D cache: 32K
CPU: L2 cache: 2048K
CPU: After all inits, caps: afe9fbff 00100000 00000000 00000040 00000180 00000000 00000000
CPU: Intel® Pentium® M processor 1.70GHz stepping 08
Enabling fast FPU save and restore... done.
Enabling unmasked SIMD FPU exception support... done.
Checking 'hlt' instruction... OK.
ACPI: Looking for DSDT in initrd... not found.
ENABLING IO-APIC IRQs
..TIMER: vector=0x31 pin1=2 pin2=-1
checking if image is initramfs...it isn't (no cpio magic); looks like an initrd
Freeing initrd memory: 1398k freed
NET: Registered protocol family 16
EISA bus registered
PCI: PCI BIOS revision 2.10 entry at 0xfd6fe, last bus=6
PCI: Using MMCONFIG
mtrr: v2.0 (20020519)
ACPI: Subsystem revision 20050211
ACPI: Interpreter enabled
ACPI: Using IOAPIC for interrupt routing
ACPI: PCI Root Bridge [PCI0] (00:00)
PCI: Probing PCI hardware (bus 00)
PCI: Ignoring BAR0-3 of IDE controller 0000:00:1f.1
PCI: Transparent bridge - 0000:00:1e.0
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0._PRT]
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.PCIB._PRT]
ACPI: PCI Interrupt Link [LNKA] (IRQs *10 11)
ACPI: PCI Interrupt Link [LNKB] (IRQs 10 *11)
ACPI: PCI Interrupt Link [LNKC] (IRQs 10 *11)
ACPI: PCI Interrupt Link [LNKD] (IRQs 10 *11)
ACPI: PCI Interrupt Link [LNKE] (IRQs *10 11)
ACPI: PCI Interrupt Link [LNKF] (IRQs *10 11)
ACPI: PCI Interrupt Link [LNKG] (IRQs 10 11) *0, disabled.
ACPI: PCI Interrupt Link [LNKH] (IRQs 10 *11)
ACPI: Embedded Controller [EC0] (gpe 23)
ACPI-0405: *** Error: Handler for [EmbeddedControl] returned AE_TIME
ACPI-1141: *** Error: Method execution failed [\_SB_.PCI0.LPCB.EC0_.BAT0._STA] (Node c1225280), AE_TIME
Linux Plug and Play Support v0.97 © Adam Belay
pnp: PnP ACPI init
ACPI-0405: *** Error: Handler for [EmbeddedControl] returned AE_TIME
ACPI-1141: *** Error: Method execution failed [\_SB_.PCI0.LPCB.EC0_.BAT0._STA] (Node c1225280), AE_TIME
ACPI-0158: *** Error: Method execution failed [\_SB_.PCI0.LPCB.EC0_.BAT0._STA] (Node c1225280), AE_TIME
pnp: PnP ACPI: found 7 devices
PnPBIOS: Disabled by ACPI PNP
SCSI subsystem initialized
PCI: Using ACPI for IRQ routing
** PCI interrupts are no longer routed automatically. If this
** causes a device to stop working, it is probably because the
** driver failed to call pci_enable_device(). As a temporary
** workaround, the "pci=routeirq" argument restores the old
** behavior. If this argument makes the device work again,
** please email the output of "lspci" to bjorn.helgaas@hp.com
** so I can fix the driver.
TC classifier action (bugs to netdev@oss.sgi.com cc hadi@cyberus.ca)
Simple Boot Flag at 0x37 set to 0x1
Machine check exception polling timer started.
Total HugeTLB memory allocated, 0
inotify device minor=63
VFS: Disk quotas dquot_6.5.1
Dquot-cache hash table entries: 1024 (order 0, 4096 bytes)
Squashfs 2.1-r2 (released 2004/12/15) © 2002-2004 Phillip Lougher
Initializing Cryptographic API
vesafb: framebuffer at 0xc0000000, mapped to 0xd0080000, using 6144k, total 7872k
vesafb: mode is 1024x768x16, linelength=2048, pages=4
vesafb: protected mode interface info at 00ff:44f0
vesafb: scrolling: redraw
vesafb: Truecolor: size=0:5:6:5, shift=0:11:5:0
bootsplash 3.1.6-2004/03/31: looking for picture...<6>...no good signature found.
Console: switching to colour frame buffer device 128x48
fb0: VESA VGA frame buffer device
isapnp: Scanning for PnP cards...
isapnp: No Plug & Play device found
Real Time Clock Driver v1.12
i8042.c: Detected active multiplexing controller, rev 1.1.
serio: i8042 AUX0 port at 0x60,0x64 irq 12
serio: i8042 AUX1 port at 0x60,0x64 irq 12
serio: i8042 AUX2 port at 0x60,0x64 irq 12
serio: i8042 AUX3 port at 0x60,0x64 irq 12
serio: i8042 KBD port at 0x60,0x64 irq 1
io scheduler noop registered
io scheduler anticipatory registered
io scheduler deadline registered
io scheduler cfq registered
floppy0: no floppy controllers found
RAMDISK driver initialized: 16 RAM disks of 100000K size 1024 blocksize
loop: loaded (max 8 devices)
Uniform Multi-Platform E-IDE driver Revision: 7.00alpha2
ide: Assuming 33MHz system bus speed for PIO modes; override with idebus=xx
ICH6: IDE controller at PCI slot 0000:00:1f.1
ACPI: PCI interrupt 0000:00:1f.1[A] -> GSI 16 (level, low) -> IRQ 169
ICH6: chipset revision 3
ICH6: not 100% native mode: will probe irqs later
ide0: BM-DMA at 0x1810-0x1817, BIOS settings: hda:DMA, hdb:DMA
Probing IDE interface ide0...
hda: HTS421260H9AT00, ATA DISK drive
hdb: Slimtype COMBO SSC-2485K, ATAPI CD/DVD-ROM drive
ide0 at 0x1f0-0x1f7,0x3f6 on irq 14
Probing IDE interface ide1...
Probing IDE interface ide2...
Probing IDE interface ide3...
Probing IDE interface ide4...
Probing IDE interface ide5...
hda: max request size: 1024KiB
hda: 117210240 sectors (60011 MB) w/1570KiB Cache, CHS=16383/255/63, UDMA(100)
hda: cache flushes supported
hda: hda1 hda2 hda3 < hda5 hda6 >
hdb: ATAPI 24X DVD-ROM CD-R/RW drive, 1536kB Cache, UDMA(33)
Uniform CD-ROM driver Revision: 3.20
3ware Storage Controller device driver for Linux v1.26.02.000.
3ware 9000 Storage Controller device driver for Linux v2.26.02.001.
libata version 1.10 loaded.
mice: PS/2 mouse device common for all mice
input: AT Translated Set 2 keyboard on isa0060/serio0
input: PS/2 Synaptics TouchPad on isa0060/serio4
md: linear personality registered as nr 1
md: raid0 personality registered as nr 2
md: raid1 personality registered as nr 3
md: raid10 personality registered as nr 9
md: raid5 personality registered as nr 4
raid5: automatically using best checksumming function: pIII_sse
pIII_sse : 4392.000 MB/sec
raid5: using function: pIII_sse (4392.000 MB/sec)
raid6: int32x1 585 MB/s
raid6: int32x2 765 MB/s
raid6: int32x4 492 MB/s
raid6: int32x8 453 MB/s
raid6: mmxx1 1800 MB/s
raid6: mmxx2 2144 MB/s
raid6: sse1x1 1308 MB/s
raid6: sse1x2 2238 MB/s
raid6: sse2x1 2472 MB/s
raid6: sse2x2 2644 MB/s
raid6: using algorithm sse2x2 (2644 MB/s)
md: raid6 personality registered as nr 8
md: multipath personality registered as nr 7
md: md driver 0.90.1 MAX_MD_DEVS=256, MD_SB_DISKS=27
device-mapper: 4.4.0-ioctl (2005-01-12) initialised: dm-devel@redhat.com
EISA: Probing bus 0 at eisa0
Cannot allocate resource for EISA slot 1
Cannot allocate resource for EISA slot 2
Cannot allocate resource for EISA slot 3
EISA: Detected 0 cards.
NET: Registered protocol family 2
IP: routing cache hash table of 2048 buckets, 16Kbytes
TCP established hash table entries: 8192 (order: 4, 65536 bytes)
TCP bind hash table entries: 8192 (order: 3, 32768 bytes)
TCP: Hash tables configured (established 8192 bind 8192)
NET: Registered protocol family 1
ACPI wakeup devices:
LID0 SLPB USB1 USB2 USB3 USB4 USB7 LANB MODM
ACPI: (supports S0 S3 S4 S5)
md: Autodetecting RAID arrays.
md: autorun ...
md: ... autorun DONE.
RAMDISK: Compressed image found at block 0
EXT2-fs warning: checktime reached, running e2fsck is recommended
VFS: Mounted root (ext2 filesystem).
ntfs: version magic '2.6.11-kanotix-7 preempt 586 gcc-3.3' should be '2.6.11-auditor-10 preempt 586 gcc-3.3'
ISO 9660 Extensions: Microsoft Joliet Level 3
ISO 9660 Extensions: RRIP_1991A
Freeing unused kernel memory: 288k freed
ACPI: AC Adapter [ADP1] (on-line)
ACPI: Power Button (FF) [PWRF]
ACPI: Lid Switch [LID0]
ACPI: Sleep Button (CM) [SLPB]
ACPI-0405: *** Error: Handler for [EmbeddedControl] returned AE_TIME
ACPI-1141: *** Error: Method execution failed [\_SB_.PCI0.LPCB.EC0_.BAT0._STA] (Node c1225280), AE_TIME
ACPI-0158: *** Error: Method execution failed [\_SB_.PCI0.LPCB.EC0_.BAT0._STA] (Node c1225280), AE_TIME
ACPI: CPU0 (power states: C1[C1] C2[C2] C3[C3])
ACPI: Processor [CPU0] (supports 8 throttling states)
ACPI-0405: *** Error: Handler for [EmbeddedControl] returned AE_TIME
ACPI-1141: *** Error: Method execution failed [\_TZ_.TZS0._TMP] (Node c122b9c0), AE_TIME
ACPI-0405: *** Error: Handler for [EmbeddedControl] returned AE_TIME
ACPI-1141: *** Error: Method execution failed [\_TZ_.TZS1._TMP] (Node c122b8c0), AE_TIME
ACPI: Thermal Zone [TZS1] (53 C)
ACPI: Video Device [GFX0] (multi-head: yes rom: no post: no)
Linux Kernel Card Services
options: [pci] [cardbus] [pm]
ACPI: PCI interrupt 0000:06:09.0[A] -> GSI 22 (level, low) -> IRQ 177
Yenta: CardBus bridge found at 0000:06:09.0 [1025:006a]
Yenta: Using CSCINT to route CSC interrupts to PCI
Yenta: Routing CardBus interrupts to PCI
Yenta TI: socket 0000:06:09.0, mfunc 0x00001022, devctl 0x44
Yenta: ISA IRQ mask 0x0070, PCI irq 177
Socket status: 30000020
cs: IO port probe 0x100-0x4ff: excluding 0x4d0-0x4d7
cs: IO port probe 0x800-0x8ff: excluding 0x800-0x80f
cs: IO port probe 0xc00-0xcff: excluding 0xcf8-0xcff
cs: IO port probe 0x3000-0x7fff: clean.
cs: IO port probe 0xa00-0xaff: clean.
usbcore: registered new driver usbfs
usbcore: registered new driver hub
USB Universal Host Controller Interface driver v2.2
ACPI: PCI interrupt 0000:00:1d.0[A] -> GSI 23 (level, low) -> IRQ 185
uhci_hcd 0000:00:1d.0: Intel Corp. 82801FB/FBM/FR/FW/FRW (ICH6 Family) USB UHCI #1
PCI: Setting latency timer of device 0000:00:1d.0 to 64
uhci_hcd 0000:00:1d.0: irq 185, io base 0x1820
uhci_hcd 0000:00:1d.0: new USB bus registered, assigned bus number 1
hub 1-0:1.0: USB hub found
hub 1-0:1.0: 2 ports detected
ACPI: PCI interrupt 0000:00:1d.1[B] -> GSI 17 (level, low) -> IRQ 193
uhci_hcd 0000:00:1d.1: Intel Corp. 82801FB/FBM/FR/FW/FRW (ICH6 Family) USB UHCI #2
PCI: Setting latency timer of device 0000:00:1d.1 to 64
uhci_hcd 0000:00:1d.1: irq 193, io base 0x1840
uhci_hcd 0000:00:1d.1: new USB bus registered, assigned bus number 2
hub 2-0:1.0: USB hub found
hub 2-0:1.0: 2 ports detected
ACPI: PCI interrupt 0000:00:1d.2[C] -> GSI 18 (level, low) -> IRQ 201
uhci_hcd 0000:00:1d.2: Intel Corp. 82801FB/FBM/FR/FW/FRW (ICH6 Family) USB UHCI #3
PCI: Setting latency timer of device 0000:00:1d.2 to 64
uhci_hcd 0000:00:1d.2: irq 201, io base 0x1860
uhci_hcd 0000:00:1d.2: new USB bus registered, assigned bus number 3
hub 3-0:1.0: USB hub found
hub 3-0:1.0: 2 ports detected
ACPI: PCI interrupt 0000:00:1d.3[D] -> GSI 19 (level, low) -> IRQ 209
uhci_hcd 0000:00:1d.3: Intel Corp. 82801FB/FBM/FR/FW/FRW (ICH6 Family) USB UHCI #4
PCI: Setting latency timer of device 0000:00:1d.3 to 64
uhci_hcd 0000:00:1d.3: irq 209, io base 0x1880
uhci_hcd 0000:00:1d.3: new USB bus registered, assigned bus number 4
hub 4-0:1.0: USB hub found
hub 4-0:1.0: 2 ports detected
usb 4-1: new low speed USB device using uhci_hcd and address 2
usbcore: registered new driver hiddev
ohci_hcd: 2004 Nov 08 USB 1.1 'Open' Host Controller (OHCI) Driver (PCI)
input: USB HID v1.00 Mouse [PS/2+USB Mouse] on usb-0000:00:1d.3-1
usbcore: registered new driver usbhid
drivers/usb/input/hid-core.c: v2.0:USB HID core driver
usbcore: registered new driver usbmouse
drivers/usb/input/usbmouse.c: v1.6:USB HID Boot Protocol mouse driver
ACPI: PCI interrupt 0000:00:1d.7[A] -> GSI 23 (level, low) -> IRQ 185
ehci_hcd 0000:00:1d.7: Intel Corp. 82801FB/FBM/FR/FW/FRW (ICH6 Family) USB2 EHCI Controller
PCI: Setting latency timer of device 0000:00:1d.7 to 64
ehci_hcd 0000:00:1d.7: irq 185, pci mem 0xb0040000
ehci_hcd 0000:00:1d.7: new USB bus registered, assigned bus number 5
PCI: cache line size of 32 is not supported by device 0000:00:1d.7
ehci_hcd 0000:00:1d.7: USB 2.0 initialized, EHCI 1.00, driver 10 Dec 2004
usb 4-1: USB disconnect, address 2
hub 5-0:1.0: USB hub found
hub 5-0:1.0: 8 ports detected
usb 4-1: new low speed USB device using uhci_hcd and address 3
input: USB HID v1.00 Mouse [PS/2+USB Mouse] on usb-0000:00:1d.3-1
ts: Compaq touchscreen protocol output
Serial: 8250/16550 driver $Revision: 1.90 $ 14 ports, IRQ sharing disabled
8139too Fast Ethernet driver 0.9.27
ACPI: PCI interrupt 0000:06:07.0[A] -> GSI 20 (level, low) -> IRQ 217
eth0: RealTek RTL8139 at 0xd068a000, 00:16:d3:40:0a:5b, IRQ 217
eth0: Identified 8139 chip type 'RTL-8100B/8139D'
ieee80211_crypt: registered algorithm 'NULL'
ipw2200: Intel® PRO/Wireless 2200/2915 Network Driver, 1.0.4
ipw2200: Copyright© 2003-2004 Intel Corporation
ACPI: PCI interrupt 0000:06:05.0[A] -> GSI 21 (level, low) -> IRQ 225
ipw2200: Detected Intel PRO/Wireless 2200BG Network Connection
ipw2200: ipw-2.3-boot.fw load failed: Reason -2
ipw2200: Unable to load firmware: 0xFFFFFFFE
ipw2200: failed to register network device
ipw2200: probe of 0000:06:05.0 failed with error -5
ieee80211_crypt: unregistered algorithm 'NULL' (deinit)
ACPI: PCI interrupt 0000:00:1e.3[B] -> GSI 21 (level, low) -> IRQ 225
PCI: Setting latency timer of device 0000:00:1e.3 to 64
ALSA sound/pci/ac97/ac97_codec.c:1989: MC'97 1 converters and GPIO not ready (0xff00)
hw_random: RNG not detected
Linux agpgart interface v0.100 © Dave Jones
agpgart: Detected an Intel 915GM Chipset.
agpgart: Maximum main memory to use for agp memory: 195M
agpgart: Detected 7932K stolen memory.
agpgart: AGP aperture is 256M @ 0xc0000000
8139too Fast Ethernet driver 0.9.27
ACPI: PCI interrupt 0000:06:07.0[A] -> GSI 20 (level, low) -> IRQ 217
eth0: RealTek RTL8139 at 0xd069c000, 00:16:d3:40:0a:5b, IRQ 217
eth0: Identified 8139 chip type 'RTL-8100B/8139D'
ieee80211_crypt: registered algorithm 'NULL'
ipw2200: Intel® PRO/Wireless 2200/2915 Network Driver, 1.0.4
ipw2200: Copyright© 2003-2004 Intel Corporation
ACPI: PCI interrupt 0000:06:05.0[A] -> GSI 21 (level, low) -> IRQ 225
ipw2200: Detected Intel PRO/Wireless 2200BG Network Connection
ACPI: PCI interrupt 0000:00:1e.2[A] -> GSI 21 (level, low) -> IRQ 225
PCI: Setting latency timer of device 0000:00:1e.2 to 64
intel8x0_measure_ac97_clock: measured 49526 usecs
intel8x0: clocking to 48000
input: PC Speaker
Adding 1116480k swap on /dev/hda6. Priority:-1 extents:1
mtrr: no more MTRRs available
device eth1 entered promiscuous mode
NET: Registered protocol family 17
eth0: link up, 100Mbps, full-duplex, lpa 0x45E1
eth0: link up, 100Mbps, full-duplex, lpa 0x45E1
eth0: link up, 100Mbps, full-duplex, lpa 0x45E1

[sarutobi]

2 alektop
1. беспроводная карта по английски WiFi interface. Смотрим вывод lspci внимательно:
0000:06:05.0 Network controller: Intel Corp. PRO/Wireless 2200BG (rev 05)
отсюда вывод что карту он все таки показывает, равно как и в dmesg есть упоминание о карте
2. переходим к ndiswrapper
ищем драйвера для windows (желательно ХР или 2000 ) ищем там .inf файл и пишем
ndiswrapper -i ....inf
потом
ndiswrapper -l - показывает сообщение о загруженном драйвере и оборудовании
последний шаг по запуску модуля
depmod -a
и если нет ошибок
modprobe ndiswrapper
если все в порядке - не было никаких ошибок, предупреждений - с модулем закончили
проверяем наличие карты
iwconfig
должен отобразиться список беспроводных устройств.
iwlist <имя твоего устройства> scan
показывает список устройств, которые видны твоему.

[alektop]

2 alektop
1. беспроводная карта по английски WiFi interface. Смотрим вывод lspci внимательно:
0000:06:05.0 Network controller: Intel Corp. PRO/Wireless 2200BG (rev 05)
отсюда вывод что карту он все таки показывает, равно как и в dmesg есть упоминание о карте

Эта карта встроенная в ноуте.... К ней вопросов нет, работает без проблем... поднять нужно pheenet wl-2054g которая подключена к pcmcia, вот о ней никакой информации не выводится....

вывод cardctl ident 0:
no product info available

cardctl info 0:

PRODID_1=""
PRODID_2=""
PRODID_3=""
PRODID_4=""
MANFID=0000,0000
FUNCID=255

cardctl config 0

Vcc 3.3V Vpp1 3.3V Vpp2 3.3V
interface type is "cardbus"
irq 177 [exclusive] [level]
function 0:

[sarutobi]

хм... откуда уверенность про Prism?
http://conexant.rapla.net/ утверждает что она conexant, там же ссылка на драйвер

[alektop]

Na fheenet.com napisano chto chipset intersil... ottuda i uverennost...

[alektop]

А в общем то на http://conexant.rapla.net/ написана история конексанта

Conexant WLAN chipsets history

* PRISM chipset developed by Harris Semiconductor
* Harris Semiconductor changed its name to Intersil Corporation on July 16, 1999
* PRISM2 chipset by Intersil unveiled on August 24, 1999
* Intersil's Wireless Networking Product Group was bought by GlobespanVirata on August 28, 2003
* Conexant (formerly Rockwell) merged with GlobespanVirata on November 3, 2003


Так что интесил и конексант одно и тоже....

[sarutobi]

так что с картой? завелась или нет?
попадалось мне в интернете (не помню где правда) что для запуска prism чипа на usb карте надо было загрузить модуль prism2usb (modprobe prism2usb). Так же помню что был рядом модуль prism2pci, насчет prism2pcmci не уверен.....
или попробуй ndiswrapper как я описал

[Кто-то]

а

Код: Выделить всё

lsmod | grep pcmcia

что говорит?

[alektop]

root@box:~# lsmod | grep pcmcia
pcmcia 18696 4
pcmcia_core 40240 3 pcmcia,yenta_socket,rsrc_nonstatic

карта так и не завелась... она вообще не определяется...

[sarutobi]

хм все чудесатей и чудесатей. Нашел вот такой совет:
добавить в параметры загрузки опцию pci=assign-busses
вот объяснение:

On Fri, Dec 09, 2005 at 10:58:55AM +1100, Joo Ghee wrote:
> Without adding "pci=assign-busses", this is the lspci -v output:
Thanks,

> 0000:00:1e.0 PCI bridge: Intel Corp. 82801 PCI Bridge (rev d3)
> (prog-if 01 [Subtractive decode])
> Flags: bus master, fast devsel, latency 0
> Bus: primary=00, secondary=06, subordinate=06, sec-latency=32

This PCI bridge connects devices which are on a secondary PCI bus -- here
numbered 06 -- to the root PCI bus, which itself is connected to the CPU.

CPU
|
|
PCI bus 00 -- 0000:00:1e.0 -- PCI bus 06

Now, on this bus, there's the CardBus bridge:

> 0000:06:09.0 CardBus bridge: ENE Technology Inc CB1410 Cardbus
> Controller (rev 01)
> Bus: primary=06, secondary=07, subordinate=0a, sec-latency=176

And it connects new CardBus devices, but as it is a _bridge_, these devices
are on a different bus, here named 07 (see the _secondary_)

PCI bus 06 -- 0000:06:09.0 -- CardBus device
on PCI bus07

Now, the CPU wants to access this device. It sees the bus number 07. How to
get there? The bridge from bus 00 to bus 06 would need to know to "transmit"
this request to bus 06, so that the CardBus bridge on 06 can transmit it to
the CardBus device. However, the bridge 0000:00:1e.0 only thinks busses 06
(secondary) to 06 (subordinate) are connected to it -- and therefore it does
not transmit the access ==> failure.

так что попробуй lspci -v

[alektop]

Ээээ... в общем не скроный вопрос... куда добавить?

[sarutobi]

Ээээ... в общем не скроный вопрос... куда добавить?

в параметры загрузки. Зависит от того какой у тебя boot-loader: LILO или GRUB. Если GRUB - нажми e во время загрузки, добавь к списку параметров. Более полную информацию - используй поиск по форуму, тема поднималась не раз.

[alektop]

Добавил... пишет Error 27: Unrecognized command

[sarutobi]

uname -a в студию?
и почитай вот здесь
http://occom.no-ip.biz/r4000.html
про PCMCIA контроллер.
Скорее всего после его настройки заработает все остальное

[alektop]

Уррааа! Вижу адаптер!
2 sarutobi спасибо тебе огромное! Просто я в gbub намудрил, счас исправил и адаптер определился! Я так понимаю это происходит потому что PCMCIA контроллер находится за PCI-PCI мостом...

[sarutobi]

Your welcome!

[alektop]

Добрый день еще раз! Такой вопросик возник. Каким образом можно отключить встроенный беспроводный адаптер на ноутбуке... а то сильно уж фонит! Спасибо за помощь.

[BaZilio]

Выгрузить соответствующий модуль ядра и убрать его из автозагрузки.