Проблема с SATA

[kolan]

Так как я являюсь полноправным чайником (с Линуксом общаюсь третий день), то задаю вопрос именно в этот подфорум

Установлен значит Suse 10.1 - то что дали, то и установил

Проблема в следующем:
Имеется 2 винча, один - ide, другой sata. Линукс установлен на ide. A винч sata не определяется
Как с эти справиться?

Заранее спасибо!

[Uncle_Theodore]

Так как я являюсь полноправным чайником (с Линуксом общаюсь третий день), то задаю вопрос именно в этот подфорум

Установлен значит Suse 10.1 - то что дали, то и установил

Проблема в следующем:
Имеется 2 винча, один - ide, другой sata. Линукс установлен на ide. A винч sata не определяется
Как с эти справиться?

Заранее спасибо!

Покажи вывод команды
fdisk -l
от рута.

[Liksys]

дополню, покажи еще dmesg

[kolan]

Код: Выделить всё

Disk /dev/hda: 120.0 GB, 120034123776 bytes
255 heads, 63 sectors/track, 14593 cylinders
Units = cylinders of 16065 * 512 = 8225280 bytes

   Device Boot      Start         End      Blocks   Id  System
/dev/hda1   *           1        5108    41021977    c  W95 FAT32 (LBA)
/dev/hda2            5108       14593    76196264    f  W95 Ext'd (LBA)
/dev/hda5            5108        5369     2104483+  82  Linux swap / Solaris
/dev/hda6            5370        7980    20972826   83  Linux
/dev/hda7            7981       14593    53118891   83  Linux

Disk /dev/sda: 200.0 GB, 200049647616 bytes
255 heads, 63 sectors/track, 24321 cylinders
Units = cylinders of 16065 * 512 = 8225280 bytes

   Device Boot      Start         End      Blocks   Id  System
/dev/sda1   *           1        5099    40957686    c  W95 FAT32 (LBA)
/dev/sda2            5100       24321   154400715    c  W95 FAT32 (LBA)

Это то, что было выдано на команду fdisk -l

Код:

Linux version 2.6.16.27-0.6-default (geeko@buildhost) (gcc version 4.1.0 (SUSE L inux)) #1 Wed Dec 13 09:34:50 UTC 2006 BIOS-provided physical RAM map: BIOS-e820: 0000000000000000 - 000000000009d800 (usable) BIOS-e820: 000000000009d800 - 00000000000a0000 (reserved) BIOS-e820: 00000000000f0000 - 0000000000100000 (reserved) BIOS-e820: 0000000000100000 - 000000003fff0000 (usable) BIOS-e820: 000000003fff0000 - 000000003fff3000 (ACPI NVS) BIOS-e820: 000000003fff3000 - 0000000040000000 (ACPI data) BIOS-e820: 00000000e0000000 - 00000000f0000000 (reserved) BIOS-e820: 00000000fec00000 - 00000000fec01000 (reserved) BIOS-e820: 00000000fee00000 - 00000000fef00000 (reserved) BIOS-e820: 00000000fefffc00 - 00000000ff000000 (reserved) BIOS-e820: 00000000ffff0000 - 0000000100000000 (reserved) 127MB HIGHMEM available. 896MB LOWMEM available. found SMP MP-table at 000f3b30 On node 0 totalpages: 262128 DMA zone: 4096 pages, LIFO batch:0 DMA32 zone: 0 pages, LIFO batch:0 Normal zone: 225280 pages, LIFO batch:31 HighMem zone: 32752 pages, LIFO batch:7 DMI 2.2 present. IO/L-APIC allowed because system is MP or new enough ACPI: RSDP (v000 Nvidia ) @ 0x000f8130 ACPI: RSDT (v001 Nvidia AWRDACPI 0x42302e31 AWRD 0x00000000) @ 0x3fff3040 ACPI: FADT (v001 Nvidia AWRDACPI 0x42302e31 AWRD 0x00000000) @ 0x3fff30c0 ACPI: MCFG (v001 Nvidia AWRDACPI 0x42302e31 AWRD 0x00000000) @ 0x3fff9240 ACPI: MADT (v001 Nvidia AWRDACPI 0x42302e31 AWRD 0x00000000) @ 0x3fff9180 ACPI: DSDT (v001 NVIDIA AWRDACPI 0x00001000 MSFT 0x0100000e) @ 0x00000000 ACPI: PM-Timer IO Port: 0x1008 ACPI: Local APIC address 0xfee00000 ACPI: LAPIC (acpi_id[0x00] lapic_id[0x00] enabled) Processor #0 15:12 APIC version 16 ACPI: LAPIC_NMI (acpi_id[0x00] high edge lint[0x1]) ACPI: IOAPIC (id[0x02] address[0xfec00000] gsi_base[0]) IOAPIC[0]: apic_id 2, version 17, address 0xfec00000, GSI 0-23 ACPI: INT_SRC_OVR (bus 0 bus_irq 0 global_irq 2 dfl dfl) ACPI: BIOS IRQ0 pin2 override ignored. ACPI: INT_SRC_OVR (bus 0 bus_irq 9 global_irq 9 high level) ACPI: INT_SRC_OVR (bus 0 bus_irq 14 global_irq 14 high edge) ACPI: INT_SRC_OVR (bus 0 bus_irq 15 global_irq 15 high edge) ACPI: IRQ9 used by override. ACPI: IRQ14 used by override. ACPI: IRQ15 used by override. Using ACPI (MADT) for SMP configuration information Allocating PCI resources starting at 50000000 (gap: 40000000:a0000000) Built 1 zonelists Kernel command line: root=/dev/hda6 devfs=mount,dall resume=/dev/hda5 splash=s ilent bootsplash: silent mode. Enabling fast FPU save and restore... done. Enabling unmasked SIMD FPU exception support... done. Initializing CPU#0 PID hash table entries: 4096 (order: 12, 65536 bytes) Detected 1808.511 MHz processor. Using tsc for high-res timesource Console: colour VGA+ 80x25 Dentry cache hash table entries: 131072 (order: 7, 524288 bytes) Inode-cache hash table entries: 65536 (order: 6, 262144 bytes) Memory: 1033788k/1048512k available (1490k kernel code, 14004k reserved, 608k da ta, 156k init, 131008k highmem) Checking if this processor honours the WP bit even in supervisor mode... Ok. Calibrating delay using timer specific routine.. 3620.57 BogoMIPS (lpj=7241141) Security Framework v1.0.0 initialized Mount-cache hash table entries: 512 CPU: After generic identify, caps: 078bfbff e3d3fbff 00000000 00000000 00000001 00000000 00000001 CPU: After vendor identify, caps: 078bfbff e3d3fbff 00000000 00000000 00000001 0 0000000 00000001 CPU: L1 I Cache: 64K (64 bytes/line), D cache 64K (64 bytes/line) CPU: L2 Cache: 256K (64 bytes/line) CPU: After all inits, caps: 078bfbff e3d3fbff 00000000 00000410 00000001 0000000 0 00000001 Intel machine check architecture supported. Intel machine check reporting enabled on CPU#0. CPU: AMD Hammer Family processor - Model Unknown stepping 02 Checking 'hlt' instruction... OK. checking if image is initramfs... it is Freeing initrd memory: 2308k freed not found! ENABLING IO-APIC IRQs ..TIMER: vector=0x31 apic1=0 pin1=0 apic2=-1 pin2=-1 NET: Registered protocol family 16 ACPI: bus type pci registered PCI: PCI BIOS revision 3.00 entry at 0xfab80, last bus=5 PCI: Using MMCONFIG PCI: No mmconfig possible on 0:18 ACPI: Subsystem revision 20060127 ACPI: Interpreter enabled ACPI: Using IOAPIC for interrupt routing ACPI: PCI Root Bridge [PCI0] (0000:00) PCI: Probing PCI hardware (bus 00) PCI: Transparent bridge - 0000:00:09.0 Boot video device is 0000:05:00.0 ACPI: PCI Interrupt Routing Table [\_SB_.PCI0._PRT] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.HUB0._PRT] ACPI: PCI Interrupt Link [LNK1] (IRQs 3 4 5 7 9 10 11 12 14 15) *0, disabled. ACPI: PCI Interrupt Link [LNK2] (IRQs 3 4 5 7 9 10 11 12 14 15) *0, disabled. ACPI: PCI Interrupt Link [LNK3] (IRQs 3 4 *5 7 9 10 11 12 14 15) ACPI: PCI Interrupt Link [LNK4] (IRQs 3 4 5 7 9 10 11 12 14 15) *0, disabled. ACPI: PCI Interrupt Link [LNK5] (IRQs 3 4 5 7 9 10 11 12 14 15) *0, disabled. ACPI: PCI Interrupt Link [LUBA] (IRQs 3 4 5 7 9 10 *11 12 14 15) ACPI: PCI Interrupt Link [LUBB] (IRQs 3 4 5 7 9 10 11 12 14 15) *0, disabled. ACPI: PCI Interrupt Link [LMAC] (IRQs 3 4 5 7 9 *10 11 12 14 15) ACPI: PCI Interrupt Link [LACI] (IRQs 3 4 5 7 9 10 *11 12 14 15) ACPI: PCI Interrupt Link [LMCI] (IRQs 3 4 5 7 9 10 11 12 14 15) *0, disabled. ACPI: PCI Interrupt Link [LSMB] (IRQs 3 4 5 7 9 *10 11 12 14 15) ACPI: PCI Interrupt Link [LUB2] (IRQs 3 4 *5 7 9 10 11 12 14 15) ACPI: PCI Interrupt Link [LIDE] (IRQs 3 4 5 7 9 10 11 12 14 15) *0, disabled. ACPI: PCI Interrupt Link [LSID] (IRQs 3 4 5 7 9 10 *11 12 14 15) ACPI: PCI Interrupt Link [LFID] (IRQs 3 4 5 7 9 *10 11 12 14 15) ACPI: PCI Interrupt Link [LPCA] (IRQs 3 4 5 7 9 10 11 12 14 15) *0, disabled. ACPI: PCI Interrupt Link [APC1] (IRQs 16) *0, disabled. ACPI: PCI Interrupt Link [APC2] (IRQs 17) *0, disabled. ACPI: PCI Interrupt Link [APC3] (IRQs 18) *0, disabled. ACPI: PCI Interrupt Link [APC4] (IRQs 19) *0, disabled. ACPI: PCI Interrupt Link [APC5] (IRQs *16), disabled. ACPI: PCI Interrupt Link [APCF] (IRQs 20 21 22 23) *0, disabled. ACPI: PCI Interrupt Link [APCG] (IRQs 20 21 22 23) *0, disabled. ACPI: PCI Interrupt Link [APCH] (IRQs 20 21 22 23) *0, disabled. ACPI: PCI Interrupt Link [APCJ] (IRQs 20 21 22 23) *0, disabled. ACPI: PCI Interrupt Link [APCK] (IRQs 20 21 22 23) *0, disabled. ACPI: PCI Interrupt Link [APCS] (IRQs 20 21 22 23) *0, disabled. ACPI: PCI Interrupt Link [APCL] (IRQs 20 21 22 23) *0, disabled. ACPI: PCI Interrupt Link [APCZ] (IRQs 20 21 22 23) *0, disabled. ACPI: PCI Interrupt Link [APSI] (IRQs 20 21 22 23) *0, disabled. ACPI: PCI Interrupt Link [APSJ] (IRQs 20 21 22 23) *0, disabled. ACPI: PCI Interrupt Link [APCP] (IRQs 20 21 22 23) *0, disabled. Linux Plug and Play Support v0.97 © Adam Belay pnp: PnP ACPI init pnp: PnP ACPI: found 15 devices PCI: Using ACPI for IRQ routing PCI: If a device doesn't work, try "pci=routeirq". If it helps, post a report PCI: Cannot allocate resource region 3 of device 0000:05:00.0 TC classifier action (bugs to netdev@vger.kernel.org cc hadi@cyberus.ca) Setting up standard PCI resources pnp: 00:00: ioport range 0x1000-0x107f could not be reserved pnp: 00:00: ioport range 0x1080-0x10ff has been reserved pnp: 00:00: ioport range 0x1400-0x147f has been reserved pnp: 00:00: ioport range 0x1480-0x14ff could not be reserved pnp: 00:00: ioport range 0x1800-0x187f has been reserved pnp: 00:00: ioport range 0x1880-0x18ff has been reserved PCI: Bridge: 0000:00:09.0 IO window: a000-afff MEM window: fe900000-fe9fffff PREFETCH window: fea00000-feafffff PCI: Bridge: 0000:00:0b.0 IO window: 9000-9fff MEM window: fe800000-fe8fffff PREFETCH window: fe700000-fe7fffff PCI: Bridge: 0000:00:0c.0 IO window: 8000-8fff MEM window: fe600000-fe6fffff PREFETCH window: fe500000-fe5fffff PCI: Bridge: 0000:00:0d.0 IO window: 7000-7fff MEM window: fe400000-fe4fffff PREFETCH window: fe300000-fe3fffff PCI: Bridge: 0000:00:0e.0 IO window: 6000-6fff MEM window: fc000000-fdffffff PREFETCH window: b0000000-cfffffff PCI: Setting latency timer of device 0000:00:09.0 to 64 PCI: Setting latency timer of device 0000:00:0b.0 to 64 PCI: Setting latency timer of device 0000:00:0c.0 to 64 PCI: Setting latency timer of device 0000:00:0d.0 to 64 PCI: Setting latency timer of device 0000:00:0e.0 to 64 apm: BIOS version 1.2 Flags 0x07 (Driver version 1.16ac) apm: overridden by ACPI. audit: initializing netlink socket (disabled) audit(1172094990.708:1): initialized highmem bounce pool size: 64 pages Total HugeTLB memory allocated, 0 VFS: Disk quotas dquot_6.5.1 Dquot-cache hash table entries: 1024 (order 0, 4096 bytes) Initializing Cryptographic API io scheduler noop registered io scheduler anticipatory registered io scheduler deadline registered io scheduler cfq registered (default) PCI: Setting latency timer of device 0000:00:0b.0 to 64 pcie_portdrv_probe->Dev[005d:10de] has invalid IRQ. Check vendor BIOS assign_interrupt_mode Found MSI capability Allocate Port Service[0000:00:0b.0:pcie00] Allocate Port Service[0000:00:0b.0:pcie03] PCI: Setting latency timer of device 0000:00:0c.0 to 64 pcie_portdrv_probe->Dev[005d:10de] has invalid IRQ. Check vendor BIOS assign_interrupt_mode Found MSI capability Allocate Port Service[0000:00:0c.0:pcie00] Allocate Port Service[0000:00:0c.0:pcie03] PCI: Setting latency timer of device 0000:00:0d.0 to 64 pcie_portdrv_probe->Dev[005d:10de] has invalid IRQ. Check vendor BIOS assign_interrupt_mode Found MSI capability Allocate Port Service[0000:00:0d.0:pcie00] Allocate Port Service[0000:00:0d.0:pcie03] PCI: Setting latency timer of device 0000:00:0e.0 to 64 pcie_portdrv_probe->Dev[005d:10de] has invalid IRQ. Check vendor BIOS assign_interrupt_mode Found MSI capability Allocate Port Service[0000:00:0e.0:pcie00] Allocate Port Service[0000:00:0e.0:pcie03] isapnp: Scanning for PnP cards... isapnp: No Plug & Play device found Real Time Clock Driver v1.12ac PNP: PS/2 Controller [PNP0303:PS2K,PNP0f13:PS2M] at 0x60,0x64 irq 1,12 serio: i8042 AUX port at 0x60,0x64 irq 12 serio: i8042 KBD port at 0x60,0x64 irq 1 Serial: 8250/16550 driver $Revision: 1.90 $ 4 ports, IRQ sharing enabled serial8250: ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A serial8250: ttyS1 at I/O 0x2f8 (irq = 3) is a 16550A 00:08: ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A Floppy drive(s): fd0 is 1.44M FDC 0 is a post-1991 82077 RAMDISK driver initialized: 16 RAM disks of 64000K size 1024 blocksize mice: PS/2 mouse device common for all mice input: AT Translated Set 2 keyboard as /class/input/input0 input: ImExPS/2 Generic Explorer Mouse as /class/input/input1 input: PC Speaker as /class/input/input2 md: md driver 0.90.3 MAX_MD_DEVS=256, MD_SB_DISKS=27 md: bitmap version 4.39 NET: Registered protocol family 2 IP route cache hash table entries: 65536 (order: 6, 262144 bytes) TCP established hash table entries: 262144 (order: 8, 1048576 bytes) TCP bind hash table entries: 65536 (order: 6, 262144 bytes) TCP: Hash tables configured (established 262144 bind 65536) TCP reno registered NET: Registered protocol family 1 Using IPI Shortcut mode ACPI wakeup devices: HUB0 XVR0 XVR1 XVR2 XVR3 USB0 USB2 MMAC MMCI UAR1 ACPI: (supports S0 S3 S4 S5) Freeing unused kernel memory: 156k freed Uniform Multi-Platform E-IDE driver Revision: 7.00alpha2 ide: Assuming 33MHz system bus speed for PIO modes; override with idebus=xx SCSI subsystem initialized NFORCE-CK804: IDE controller at PCI slot 0000:00:06.0 NFORCE-CK804: chipset revision 162 NFORCE-CK804: not 100% native mode: will probe irqs later NFORCE-CK804: 0000:00:06.0 (rev a2) UDMA133 controller ide0: BM-DMA at 0xe000-0xe007, BIOS settings: hda:DMA, hdb:DMA ide1: BM-DMA at 0xe008-0xe00f, BIOS settings: hdc:DMA, hdd:DMA Probing IDE interface ide0... hda: ST3120026A, ATA DISK drive hdb: SONY DVD RW DW-Q30A, ATAPI CD/DVD-ROM drive ide0 at 0x1f0-0x1f7,0x3f6 on irq 14 hda: max request size: 512KiB hda: 234441648 sectors (120034 MB) w/8192KiB Cache, CHS=16383/255/63, UDMA(100) hda: cache flushes supported hda: hda1 hda2 < hda5 hda6 hda7 > Probing IDE interface ide1... libata version 1.20 loaded. sata_nv 0000:00:07.0: version 0.8 ACPI: PCI Interrupt Link [APSI] enabled at IRQ 23 ACPI: PCI Interrupt 0000:00:07.0[A] -> Link [APSI] -> GSI 23 (level, low) -> IRQ 217 PCI: Setting latency timer of device 0000:00:07.0 to 64 ata1: SATA max UDMA/133 cmd 0x9F0 ctl 0xBF2 bmdma 0xCC00 irq 217 ata2: SATA max UDMA/133 cmd 0x970 ctl 0xB72 bmdma 0xCC08 irq 217 ata1: SATA link up 1.5 Gbps (SStatus 113) ata1: dev 0 cfg 00:0c5a 49:2f00 82:346b 83:7d01 84:4023 85:3469 86:3c01 87:4023 88:407f 93:0000 ata1: dev 0 ATA-7, max UDMA/133, 390721968 sectors: LBA48 sata_get_dev_handle: SATA dev addr=0x70000, handle=0xdffea2c0 nv_sata: Primary device added nv_sata: Primary device removed nv_sata: Secondary device added nv_sata: Secondary device removed ata1: dev 0 configured for UDMA/133 sata_get_dev_handle: SATA dev addr=0x70000, handle=0xdffea2c0 scsi0 : sata_nv ata2: SATA link down (SStatus 0) scsi1 : sata_nv Vendor: ATA Model: ST3200826AS Rev: 3.03 Type: Direct-Access ANSI SCSI revision: 05 SCSI device sda: 390721968 512-byte hdwr sectors (200050 MB) sda: Write Protect is off sda: Mode Sense: 00 3a 00 00 SCSI device sda: drive cache: write back SCSI device sda: 390721968 512-byte hdwr sectors (200050 MB) sda: Write Protect is off sda: Mode Sense: 00 3a 00 00 SCSI device sda: drive cache: write back sda:<4>nv_sata: Primary device added nv_sata: Primary device removed nv_sata: Secondary device added nv_sata: Secondary device removed sda1 sda2 sd 0:0:0:0: Attached scsi disk sda ACPI: PCI Interrupt Link [APSJ] enabled at IRQ 22 ACPI: PCI Interrupt 0000:00:08.0[A] -> Link [APSJ] -> GSI 22 (level, low) -> IRQ 225 PCI: Setting latency timer of device 0000:00:08.0 to 64 ata3: SATA max UDMA/133 cmd 0x9E0 ctl 0xBE2 bmdma 0xB800 irq 225 ata4: SATA max UDMA/133 cmd 0x960 ctl 0xB62 bmdma 0xB808 irq 225 sd 0:0:0:0: Attached scsi generic sg0 type 0 ata3: SATA link down (SStatus 0) scsi2 : sata_nv ata4: SATA link down (SStatus 0) scsi3 : sata_nv ACPI: Processor [CPU0] (supports 8 throttling states) ACPI: Thermal Zone [THRM] (40 C) ACPI: Fan [FAN] (on) BIOS EDD facility v0.16 2004-Jun-25, 2 devices found Attempting manual resume ReiserFS: hda6: found reiserfs format "3.6" with standard journal ReiserFS: hda6: using ordered data mode reiserfs: using flush barriers ReiserFS: hda6: journal params: device hda6, size 8192, journal first block 18, max trans len 1024, max batch 900, max commit age 30, max trans age 30 ReiserFS: hda6: checking transaction log (hda6) ReiserFS: hda6: Using r5 hash to sort names parport: PnPBIOS parport detected. parport0: PC-style at 0x378, irq 7 [PCSPP,TRISTATE] lp0: using parport0 (interrupt-driven). Linux agpgart interface v0.101 © Dave Jones usbcore: registered new driver usbfs usbcore: registered new driver hub ACPI: PCI Interrupt Link [APCL] enabled at IRQ 21 ACPI: PCI Interrupt 0000:00:02.1 -> Link [APCL] -> GSI 21 (level, low) -> IRQ 233 PCI: Setting latency timer of device 0000:00:02.1 to 64 ehci_hcd 0000:00:02.1: EHCI Host Controller ehci_hcd 0000:00:02.1: debug port 1 PCI: cache line size of 64 is not supported by device 0000:00:02.1 ehci_hcd 0000:00:02.1: new USB bus registered, assigned bus number 1 ehci_hcd 0000:00:02.1: irq 233, io mem 0xfebfe000 ehci_hcd 0000:00:02.1: USB 2.0 started, EHCI 1.00, driver 10 Dec 2004 usb usb1: new device found, idVendor=0000, idProduct=0000 usb usb1: new device strings: Mfr=3, Product=2, SerialNumber=1 usb usb1: Product: EHCI Host Controller usb usb1: Manufacturer: Linux 2.6.16.27-0.6-default ehci_hcd usb usb1: SerialNumber: 0000:00:02.1 usb usb1: configuration #1 chosen from 1 choice hub 1-0:1.0: USB hub found hub 1-0:1.0: 10 ports detected snd_page_alloc: module not supported by Novell, setting U taint flag. Linux video capture interface: v1.00 saa7130/34: v4l2 driver version 0.2.14 loaded ACPI: PCI Interrupt Link [APC3] enabled at IRQ 18 ACPI: PCI Interrupt 0000:01:0a.0[A] -> Link [APC3] -> GSI 18 (level, low) -> IRQ 50 saa7133[0]: found at 0000:01:0a.0, rev: 240, irq: 50, latency: 32, mmio: 0xfe9ff 000 saa7133[0]: subsystem: 0000:507b, board: UNKNOWN/GENERIC [card=0,autodetected] saa7133[0]: board init: gpio is 200000 snd: module not supported by Novell, setting U taint flag. i2c_adapter i2c-1: nForce2 SMBus adapter at 0x1c00 i2c_adapter i2c-2: nForce2 SMBus adapter at 0x1d00 saa7133[0]: i2c eeprom 00: 00 00 7b 50 54 20 00 00 00 00 00 00 00 00 00 01 saa7133[0]: i2c eeprom 10: ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff saa7133[0]: i2c eeprom 20: ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff saa7133[0]: i2c eeprom 30: ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff saa7133[0]: i2c eeprom 40: ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff saa7133[0]: i2c eeprom 50: ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff saa7133[0]: i2c eeprom 60: ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff saa7133[0]: i2c eeprom 70: ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff saa7133[0]: registered device video0 [v4l2] saa7133[0]: registered device vbi0 nvidia: module license 'NVIDIA' taints kernel. snd_timer: module not supported by Novell, setting U taint flag. snd_pcm: module not supported by Novell, setting U taint flag. snd_ac97_bus: module not supported by Novell, setting U taint flag. snd_ac97_codec: module not supported by Novell, setting U taint flag. snd_intel8x0: module not supported by Novell, setting U taint flag. ACPI: PCI Interrupt Link [APCJ] enabled at IRQ 20 ACPI: PCI Interrupt 0000:00:04.0[A] -> Link [APCJ] -> GSI 20 (level, low) -> IRQ 58 PCI: Setting latency timer of device 0000:00:04.0 to 64 forcedeth.c: Reverse Engineered nForce ethernet driver. Version 0.49. ohci_hcd: 2005 April 22 USB 1.1 'Open' Host Controller (OHCI) Driver (PCI) hdb: ATAPI 126X DVD-ROM DVD-R CD-R/RW drive, 2048kB Cache Uniform CD-ROM driver Revision: 3.20 intel8x0_measure_ac97_clock: measured 67140 usecs intel8x0: clocking to 47161 ACPI: PCI Interrupt 0000:05:00.0[A] -> Link [APC3] -> GSI 18 (level, low) -> IRQ 50 PCI: Setting latency timer of device 0000:05:00.0 to 64 NVRM: loading NVIDIA Linux x86 Kernel Module 1.0-8776 Mon Oct 16 21:56:04 PDT 2006 ACPI: PCI Interrupt Link [APCH] enabled at IRQ 23 ACPI: PCI Interrupt 0000:00:0a.0[A] -> Link [APCH] -> GSI 23 (level, low) -> IRQ 217 PCI: Setting latency timer of device 0000:00:0a.0 to 64 eth0: forcedeth.c: subsystem: 0105b:0ca2 bound to 0000:00:0a.0 ACPI: PCI Interrupt Link [APCF] enabled at IRQ 22 ACPI: PCI Interrupt 0000:00:02.0[A] -> Link [APCF] -> GSI 22 (level, low) -> IRQ 225 PCI: Setting latency timer of device 0000:00:02.0 to 64 ohci_hcd 0000:00:02.0: OHCI Host Controller ohci_hcd 0000:00:02.0: new USB bus registered, assigned bus number 2 ohci_hcd 0000:00:02.0: irq 225, io mem 0xfebff000 usb usb2: new device found, idVendor=0000, idProduct=0000 usb usb2: new device strings: Mfr=3, Product=2, SerialNumber=1 usb usb2: Product: OHCI Host Controller usb usb2: Manufacturer: Linux 2.6.16.27-0.6-default ohci_hcd usb usb2: SerialNumber: 0000:00:02.0 usb usb2: configuration #1 chosen from 1 choice hub 2-0:1.0: USB hub found hub 2-0:1.0: 10 ports detected usb 2-3: new full speed USB device using ohci_hcd and address 2 usb 2-3: new device found, idVendor=07b2, idProduct=5100 usb 2-3: new device strings: Mfr=1, Product=2, SerialNumber=3 usb 2-3: Product: USB Cable Modem usb 2-3: Manufacturer: Broadcom Corporation usb 2-3: SerialNumber: 00111A737913 usb 2-3: configuration #1 chosen from 1 choice eth1: register 'cdc_ether' at usb-0000:00:02.0-3, CDC Ethernet Device, 00:11:1a: 73:79:13 usbcore: registered new driver cdc_ether device-mapper: 4.5.0-ioctl (2005-10-04) initialised: dm-devel@redhat.com dm-netlink version 0.0.2 loaded loop: loaded (max 8 devices) ReiserFS: hda7: found reiserfs format "3.6" with standard journal ReiserFS: hda7: using ordered data mode reiserfs: using flush barriers ReiserFS: hda7: journal params: device hda7, size 8192, journal first block 18, max trans len 1024, max batch 900, max commit age 30, max trans age 30 ReiserFS: hda7: checking transaction log (hda7) ReiserFS: hda7: Using r5 hash to sort names AppArmor: AppArmor (version 2.0-19.43r6320) initialized audit(1172095016.693:2): AppArmor (version 2.0-19.43r6320) initialized NET: Registered protocol family 10 lo: Disabled Privacy Extensions IPv6 over IPv4 tunneling driver ip6_tables: © 2000-2006 Netfilter Core Team ip_tables: © 2000-2006 Netfilter Core Team Netfilter messages via NETLINK v0.30. ip_conntrack version 2.4 (8191 buckets, 65528 max) - 232 bytes per conntrack Adding 2104472k swap on /dev/hda5. Priority:-1 extents:1 across:2104472k ACPI: Power Button (FF) [PWRF] ACPI: Power Button (CM) [PWRB] NET: Registered protocol family 17 snd_seq_device: module not supported by Novell, setting U taint flag. snd_seq: module not supported by Novell, setting U taint flag. snd_mixer_oss: module not supported by Novell, setting U taint flag. snd_pcm_oss: module not supported by Novell, setting U taint flag. powernow-k8: Found 1 AMD Athlon 64 / Opteron processors (version 1.60.2) ACPI Exception (acpi_processor-0239): AE_NOT_FOUND, Evaluating _PSS [20060127] powernow-k8: BIOS error - no PSB or ACPI _PSS objects powernow: This module only works with AMD K7 CPUs ACPI Exception (acpi_processor-0239): AE_NOT_FOUND, Evaluating _PSS [20060127] eth1: no IPv6 routers present SFW2-INext-DROP-DEFLT IN=eth1 OUT= MAC= SRC=172.31.151.251 DST=224.0.0.251 LEN=1 13 TOS=0x00 PREC=0x00 TTL=255 ID=0 DF PROTO=UDP SPT=5353 DPT=5353 LEN=93 SFW2-INext-DROP-DEFLT IN=eth1 OUT= MAC=01:00:5e:00:00:01:00:00:ca:26:af:34:08:00 SRC=10.1.0.2 DST=224.0.0.1 LEN=28 TOS=0x00 PREC=0x00 TTL=1 ID=41206 PROTO=2 SFW2-INext-DROP-DEFLT IN=eth1 OUT= MAC=01:00:5e:00:00:01:00:00:ca:26:af:34:08:00 SRC=10.1.0.2 DST=224.0.0.1 LEN=28 TOS=0x00 PREC=0x00 TTL=1 ID=41209 PROTO=2 ISO 9660 Extensions: Microsoft Joliet Level 3 ISOFS: changing to secondary root SFW2-INext-DROP-DEFLT IN=eth1 OUT= MAC= SRC=172.31.151.251 DST=224.0.0.251 LEN=1 13 TOS=0x00 PREC=0x00 TTL=255 ID=0 DF PROTO=UDP SPT=5353 DPT=5353 LEN=93 SFW2-INext-DROP-DEFLT IN=eth1 OUT= MAC=01:00:5e:00:00:01:00:00:ca:26:af:34:08:00 SRC=10.1.0.2 DST=224.0.0.1 LEN=28 TOS=0x00 PREC=0x00 TTL=1 ID=41227 PROTO=2 SFW2-INext-DROP-DEFLT IN=eth1 OUT= MAC=01:00:5e:00:00:01:00:00:ca:26:af:34:08:00 SRC=10.1.0.2 DST=224.0.0.1 LEN=28 TOS=0x00 PREC=0x00 TTL=1 ID=41234 PROTO=2 SFW2-INext-DROP-DEFLT IN=eth1 OUT= MAC=01:00:5e:00:00:01:00:00:ca:26:af:34:08:00 SRC=10.1.0.2 DST=224.0.0.1 LEN=28 TOS=0x00 PREC=0x00 TTL=1 ID=41312 PROTO=2 SFW2-INext-DROP-DEFLT IN=eth1 OUT= MAC=01:00:5e:00:00:01:00:00:ca:26:af:34:08:00 SRC=10.1.0.2 DST=224.0.0.1 LEN=28 TOS=0x00 PREC=0x00 TTL=1 ID=41341 PROTO=2 SFW2-INext-DROP-DEFLT IN=eth1 OUT= MAC=01:00:5e:00:00:01:00:00:ca:26:af:34:08:00 SRC=10.1.0.2 DST=224.0.0.1 LEN=28 TOS=0x00 PREC=0x00 TTL=1 ID=41347 PROTO=2 SFW2-INext-DROP-DEFLT IN=eth1 OUT= MAC=01:00:5e:00:00:01:00:00:ca:26:af:34:08:00 SRC=10.1.0.2 DST=224.0.0.1 LEN=28 TOS=0x00 PREC=0x00 TTL=1 ID=41349 PROTO=2 SFW2-INext-DROP-DEFLT IN=eth1 OUT= MAC=01:00:5e:00:00:01:00:00:ca:26:af:34:08:00 SRC=10.1.0.2 DST=224.0.0.1 LEN=28 TOS=0x00 PREC=0x00 TTL=1 ID=41361 PROTO=2 SFW2-INext-DROP-DEFLT IN=eth1 OUT= MAC=01:00:5e:00:00:01:00:00:ca:26:af:34:08:00 SRC=10.1.0.2 DST=224.0.0.1 LEN=28 TOS=0x00 PREC=0x00 TTL=1 ID=41410 PROTO=2 SFW2-INext-DROP-DEFLT IN=eth1 OUT= MAC=01:00:5e:00:00:01:00:00:ca:26:af:34:08:00 SRC=10.1.0.2 DST=224.0.0.1 LEN=28 TOS=0x00 PREC=0x00 TTL=1 ID=41422 PROTO=2

А это, на команду [b]dmesg


Тут я вдруг подумал: а может диск определяется, да просто я не туда смотрю?
Подскажите пожалуйста: а куда мне смотреть-то нужно?

[eduard_pustobaev]

Определяется конечно:

/dev/sda - ваш sata-диск.

fdisk же всё показывает: 120G ide - /dev/hda, 200G sata - /dev/sda

Дальше уж ищите по форуму про монтирование win-разделов.