Не определяется Sony Cyber-shot H2 (Фотоаппарат совсем не новый, но никак не определяется)

[Kitovras]

Приветствую, уважаемые
Сабж собственно. Подскажите что делать ?
Может какие драйверы есть ?

[stdds]

Приветствую, уважаемые
Сабж собственно. Подскажите что делать ?
Может какие драйверы есть ?

Это все вабще а чем?

[uptime]

подсоединяете по USB?
дайте, пожалуйста вывод команд lsusb и dmesg после подсоединения аппарата.

[Kitovras]

подсоединяете по USB?
дайте, пожалуйста вывод команд lsusb и dmesg после подсоединения аппарата.

В продолжение темы, долго не отвечал, ну уж простите..
Вот собственно:

Код: Выделить всё

lsusb
Bus 002 Device 009: ID 054c:0010 Sony Corp. DSC-S30/S70/S75/F505V/F505/FD92 Cybershot/Mavica Digital Camera
Bus 002 Device 007: ID 05e3:070e Genesys Logic, Inc.
Bus 002 Device 001: ID 0000:0000
Bus 001 Device 002: ID 04e8:0100 Samsung Electronics Co., Ltd
Bus 001 Device 001: ID 0000:0000

Код:

dmesg Linux version 2.6.17-13mdv (rtp@octopus.mandriva.com) (gcc version 4.1.2 20070302 (prerelease) (4.1.2-1mdv2007.1)) #1 SMP Fri Mar 23 19:03:31 UTC 2007 BIOS-provided physical RAM map: BIOS-e820: 0000000000000000 - 000000000009f800 (usable) BIOS-e820: 000000000009f800 - 00000000000a0000 (reserved) BIOS-e820: 00000000000f0000 - 0000000000100000 (reserved) BIOS-e820: 0000000000100000 - 000000003bff0000 (usable) BIOS-e820: 000000003bff0000 - 000000003bff3000 (ACPI NVS) BIOS-e820: 000000003bff3000 - 000000003c000000 (ACPI data) BIOS-e820: 000000003c000000 - 0000000040000000 (reserved) BIOS-e820: 00000000f0000000 - 00000000f2000000 (reserved) BIOS-e820: 00000000fec00000 - 0000000100000000 (reserved) 63MB HIGHMEM available. 895MB LOWMEM available. found SMP MP-table at 000f5190 On node 0 totalpages: 245744 DMA zone: 4096 pages, LIFO batch:0 Normal zone: 225279 pages, LIFO batch:31 HighMem zone: 16369 pages, LIFO batch:3 DMI 2.3 present. ACPI: RSDP (v000 GBT ) @ 0x000f6b40 ACPI: RSDT (v001 GBT AWRDACPI 0x42302e31 AWRD 0x01010101) @ 0x3bff3000 ACPI: FADT (v001 GBT AWRDACPI 0x42302e31 AWRD 0x01010101) @ 0x3bff3040 ACPI: MCFG (v001 GBT AWRDACPI 0x42302e31 AWRD 0x01010101) @ 0x3bff7f80 ACPI: MADT (v001 GBT AWRDACPI 0x42302e31 AWRD 0x01010101) @ 0x3bff7f00 ACPI: DSDT (v001 GBT AWRDACPI 0x00001000 MSFT 0x0100000c) @ 0x00000000 ACPI: PM-Timer IO Port: 0x1008 ACPI: Local APIC address 0xfee00000 ACPI: LAPIC (acpi_id[0x00] lapic_id[0x00] enabled) Processor #0 15:4 APIC version 16 ACPI: LAPIC (acpi_id[0x01] lapic_id[0x01] disabled) ACPI: LAPIC_NMI (acpi_id[0x00] dfl dfl lint[0x1]) ACPI: LAPIC_NMI (acpi_id[0x01] dfl dfl lint[0x1]) ACPI: IOAPIC (id[0x02] address[0xfec00000] gsi_base[0]) IOAPIC[0]: apic_id 2, version 17, address 0xfec00000, GSI 0-23 ACPI: INT_SRC_OVR (bus 0 bus_irq 9 global_irq 9 high level) ACPI: INT_SRC_OVR (bus 0 bus_irq 14 global_irq 14 high edge) ACPI: INT_SRC_OVR (bus 0 bus_irq 15 global_irq 15 high edge) ACPI: IRQ9 used by override. ACPI: IRQ14 used by override. ACPI: IRQ15 used by override. Enabling APIC mode: Flat. Using 1 I/O APICs Using ACPI (MADT) for SMP configuration information Allocating PCI resources starting at 50000000 (gap: 40000000:b0000000) Built 1 zonelists Kernel command line: BOOT_IMAGE=linux root=/dev/hda8 resume=/dev/hda9 splash=silent vga=788 bootsplash: silent mode. mapped APIC to ffffe000 (fee00000) mapped IOAPIC to ffffd000 (fec00000) Enabling fast FPU save and restore... done. Enabling unmasked SIMD FPU exception support... done. Initializing CPU#0 PID hash table entries: 4096 (order: 12, 16384 bytes) Detected 2009.357 MHz processor. Using pmtmr for high-res timesource Console: colour dummy device 80x25 Dentry cache hash table entries: 131072 (order: 7, 524288 bytes) Inode-cache hash table entries: 65536 (order: 6, 262144 bytes) Memory: 968708k/982976k available (2430k kernel code, 13144k reserved, 760k data, 244k init, 65476k highmem, 0k BadRAM) Checking if this processor honours the WP bit even in supervisor mode... Ok. Calibrating delay using timer specific routine.. 4024.54 BogoMIPS (lpj=8049092) Mount-cache hash table entries: 512 CPU: After generic identify, caps: 078bfbff e1d3fbff 00000000 00000000 00000000 00000000 00000000 CPU: After vendor identify, caps: 078bfbff e1d3fbff 00000000 00000000 00000000 00000000 00000000 CPU: L1 I Cache: 64K (64 bytes/line), D cache 64K (64 bytes/line) CPU: L2 Cache: 512K (64 bytes/line) CPU: After all inits, caps: 078bfbff e1d3fbff 00000000 00000410 00000000 00000000 00000000 Intel machine check architecture supported. Intel machine check reporting enabled on CPU#0. Checking 'hlt' instruction... OK. SMP alternatives: switching to UP code Freeing SMP alternatives: 16k freed checking if image is initramfs... it is Freeing initrd memory: 728k freed ACPI: Looking for DSDT in initramfs... error, file /DSDT.aml not found. CPU0: AMD Athlon™ 64 Processor 3000+ stepping 0a Total of 1 processors activated (4024.54 BogoMIPS). ENABLING IO-APIC IRQs ..TIMER: vector=0x31 apic1=0 pin1=0 apic2=-1 pin2=-1 Brought up 1 CPUs migration_cost=0 NET: Registered protocol family 16 ACPI: bus type pci registered PCI: Using MMCONFIG PCI: No mmconfig possible on 0:18 Setting up standard PCI resources ACPI: Subsystem revision 20060127 ACPI: Interpreter enabled ACPI: Using IOAPIC for interrupt routing ACPI: PCI Root Bridge [PCI0] (0000:00) PCI: Probing PCI hardware (bus 00) Boot video device is 0000:00:05.0 PCI: Transparent bridge - 0000:00:10.0 ACPI: PCI Interrupt Routing Table [\_SB_.PCI0._PRT] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.HUB0._PRT] ACPI: PCI Interrupt Link [LNK1] (IRQs 5 7 9 10 11 14 15) *0, disabled. ACPI: PCI Interrupt Link [LNK2] (IRQs 5 7 9 10 11 14 15) *0, disabled. ACPI: PCI Interrupt Link [LNK3] (IRQs 5 7 9 10 11 14 15) *0, disabled. ACPI: PCI Interrupt Link [LNK4] (IRQs 5 7 9 *10 11 14 15) ACPI: PCI Interrupt Link [LNK5] (IRQs 5 7 9 10 11 14 15) *0, disabled. ACPI: PCI Interrupt Link [LNK6] (IRQs 5 7 9 10 11 14 15) *0, disabled. ACPI: PCI Interrupt Link [LNK7] (IRQs *5 7 9 10 11 14 15) ACPI: PCI Interrupt Link [LNK8] (IRQs 5 7 9 10 11 14 15) *0, disabled. ACPI: PCI Interrupt Link [LUBA] (IRQs *5 7 9 10 11 14 15) ACPI: PCI Interrupt Link [LUBB] (IRQs 5 7 9 10 11 14 15) *0, disabled. ACPI: PCI Interrupt Link [LMAC] (IRQs 5 7 9 *10 11 14 15) ACPI: PCI Interrupt Link [LACI] (IRQs 5 7 9 10 *11 14 15) ACPI: PCI Interrupt Link [LAZA] (IRQs 5 7 9 10 11 14 15) *0, disabled. ACPI: PCI Interrupt Link [LPMU] (IRQs 5 7 9 10 11 14 15) *0, disabled. ACPI: PCI Interrupt Link [LMCI] (IRQs 5 7 9 10 11 14 15) *0, disabled. ACPI: PCI Interrupt Link [LSMB] (IRQs 5 7 9 *10 11 14 15) ACPI: PCI Interrupt Link [LUB2] (IRQs 5 7 9 10 *11 14 15) ACPI: PCI Interrupt Link [LIDE] (IRQs 5 7 9 10 11 14 15) *0, disabled. ACPI: PCI Interrupt Link [LSID] (IRQs 5 7 9 10 *11 14 15) ACPI: PCI Interrupt Link [LFID] (IRQs 5 7 9 10 11 14 15) *0, disabled. ACPI: PCI Interrupt Link [APC1] (IRQs 16) *0, disabled. ACPI: PCI Interrupt Link [APC2] (IRQs 17) *0, disabled. ACPI: PCI Interrupt Link [APC3] (IRQs 18) *0, disabled. ACPI: PCI Interrupt Link [APC4] (IRQs 19) *0, disabled. ACPI: PCI Interrupt Link [APC5] (IRQs 16) *0, disabled. ACPI: PCI Interrupt Link [APC6] (IRQs 16) *0, disabled. ACPI: PCI Interrupt Link [APC7] (IRQs 16) *0, disabled. ACPI: PCI Interrupt Link [APC8] (IRQs 16) *0, disabled. ACPI: PCI Interrupt Link [APCF] (IRQs 20 21 22 23) *0, disabled. ACPI: PCI Interrupt Link [APCG] (IRQs 20 21 22 23) *0, disabled. ACPI: PCI Interrupt Link [APCH] (IRQs 20 21 22 23) *0, disabled. ACPI: PCI Interrupt Link [APCJ] (IRQs 20 21 22 23) *0, disabled. ACPI: PCI Interrupt Link [APMU] (IRQs 20 21 22 23) *0, disabled. ACPI: PCI Interrupt Link [AAZA] (IRQs 20 21 22 23) *0, disabled. ACPI: PCI Interrupt Link [APCK] (IRQs 20 21 22 23) *0, disabled. ACPI: PCI Interrupt Link [APCS] (IRQs 20 21 22 23) *0, disabled. ACPI: PCI Interrupt Link [APCL] (IRQs 20 21 22 23) *0, disabled. ACPI: PCI Interrupt Link [APCM] (IRQs 20 21 22 23) *0, disabled. ACPI: PCI Interrupt Link [APCZ] (IRQs 20 21 22 23) *0, disabled. ACPI: PCI Interrupt Link [APSI] (IRQs 20 21 22 23) *0, disabled. ACPI: PCI Interrupt Link [APSJ] (IRQs 20 21 22 23) *0, disabled. Linux Plug and Play Support v0.97 © Adam Belay pnp: PnP ACPI init pnp: PnP ACPI: found 13 devices PnPBIOS: Disabled PCI: Using ACPI for IRQ routing PCI: If a device doesn't work, try "pci=routeirq". If it helps, post a report pnp: 00:01: ioport range 0x1000-0x107f could not be reserved pnp: 00:01: ioport range 0x1080-0x10ff has been reserved pnp: 00:01: ioport range 0x1400-0x147f has been reserved pnp: 00:01: ioport range 0x1480-0x14ff could not be reserved pnp: 00:01: ioport range 0x1800-0x187f has been reserved pnp: 00:01: ioport range 0x1880-0x18ff has been reserved pnp: 00:01: ioport range 0x2000-0x207f has been reserved pnp: 00:01: ioport range 0x2080-0x20ff has been reserved PCI: Bridge: 0000:00:03.0 IO window: 9000-9fff MEM window: disabled. PREFETCH window: disabled. PCI: Bridge: 0000:00:04.0 IO window: a000-afff MEM window: disabled. PREFETCH window: disabled. PCI: Bridge: 0000:00:10.0 IO window: b000-bfff MEM window: f5000000-f50fffff PREFETCH window: disabled. PCI: Setting latency timer of device 0000:00:03.0 to 64 PCI: Setting latency timer of device 0000:00:04.0 to 64 PCI: Setting latency timer of device 0000:00:10.0 to 64 NET: Registered protocol family 2 IP route cache hash table entries: 32768 (order: 5, 131072 bytes) TCP established hash table entries: 131072 (order: 8, 1048576 bytes) TCP bind hash table entries: 65536 (order: 7, 524288 bytes) TCP: Hash tables configured (established 131072 bind 65536) TCP reno registered apm: BIOS version 1.2 Flags 0x07 (Driver version 1.16ac) apm: overridden by ACPI. audit: initializing netlink socket (disabled) audit(1185174372.124:1): initialized highmem bounce pool size: 64 pages Total HugeTLB memory allocated, 0 VFS: Disk quotas dquot_6.5.1 Dquot-cache hash table entries: 1024 (order 0, 4096 bytes) Initializing Cryptographic API io scheduler noop registered io scheduler anticipatory registered (default) io scheduler deadline registered io scheduler cfq registered PCI: Setting latency timer of device 0000:00:03.0 to 64 pcie_portdrv_probe->Dev[02fd:10de] has invalid IRQ. Check vendor BIOS assign_interrupt_mode Found MSI capability Allocate Port Service[0000:00:03.0:pcie00] Allocate Port Service[0000:00:03.0:pcie03] PCI: Setting latency timer of device 0000:00:04.0 to 64 pcie_portdrv_probe->Dev[02fb:10de] has invalid IRQ. Check vendor BIOS assign_interrupt_mode Found MSI capability Allocate Port Service[0000:00:04.0:pcie00] Allocate Port Service[0000:00:04.0:pcie03] vesafb: framebuffer at 0xe0000000, mapped to 0xf8880000, using 3750k, total 65536k vesafb: mode is 800x600x16, linelength=1600, pages=2 vesafb: protected mode interface info at c000:c3b0 vesafb: scrolling: redraw vesafb: Truecolor: size=0:5:6:5, shift=0:11:5:0 bootsplash 3.1.6-2004/03/31: looking for picture...<6> silentjpeg size 194748 bytes,<6>...found (800x600, 194700 bytes, v3). Console: switching to colour frame buffer device 93x31 fb0: VESA VGA frame buffer device isapnp: Scanning for PnP cards... isapnp: No Plug & Play device found Real Time Clock Driver v1.12ac Serial: 8250/16550 driver $Revision: 1.90 $ 4 ports, IRQ sharing enabled serial8250: ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A serial8250: ttyS1 at I/O 0x2f8 (irq = 3) is a 16550A 00:07: ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A 00:08: ttyS1 at I/O 0x2f8 (irq = 3) is a 16550A RAMDISK driver initialized: 16 RAM disks of 32000K size 1024 blocksize Uniform Multi-Platform E-IDE driver Revision: 7.00alpha2 ide: Assuming 33MHz system bus speed for PIO modes; override with idebus=xx NFORCE-MCP51: IDE controller at PCI slot 0000:00:0d.0 NFORCE-MCP51: chipset revision 161 NFORCE-MCP51: not 100% native mode: will probe irqs later NFORCE-MCP51: BIOS didn't set cable bits correctly. Enabling workaround. NFORCE-MCP51: 0000:00:0d.0 (rev a1) UDMA133 controller ide0: BM-DMA at 0xf000-0xf007, BIOS settings: hda:DMA, hdb:DMA ide1: BM-DMA at 0xf008-0xf00f, BIOS settings: hdc:DMA, hdd:DMA Probing IDE interface ide0... hda: HDT722516DLAT80, ATA DISK drive ide0 at 0x1f0-0x1f7,0x3f6 on irq 14 Probing IDE interface ide1... hdc: LITE-ON DVDRW LH-20A1P, ATAPI CD/DVD-ROM drive ide1 at 0x170-0x177,0x376 on irq 15 hda: max request size: 512KiB hda: Host Protected Area detected. current capacity is 321670847 sectors (164695 MB) native capacity is 321672960 sectors (164696 MB) hda: Host Protected Area disabled. hda: 321672960 sectors (164696 MB) w/7674KiB Cache, CHS=20023/255/63, UDMA(133) hda: cache flushes supported hda: hda1 hda2 < hda5 hda6 hda7 hda8 hda9 hda10 > PNP: PS/2 Controller [PNP0303:PS2K,PNP0f13:PS2M] at 0x60,0x64 irq 1,12 serio: i8042 AUX port at 0x60,0x64 irq 12 serio: i8042 KBD port at 0x60,0x64 irq 1 mice: PS/2 mouse device common for all mice md: md driver 0.90.3 MAX_MD_DEVS=256, MD_SB_DISKS=27 md: bitmap version 4.39 TCP bic registered NET: Registered protocol family 1 Using IPI No-Shortcut mode ACPI wakeup devices: HUB0 XVRA XVRB XVRC USB0 USB2 AZAD MMAC MMCI UAR1 ACPI: (supports S0 S3 S4 S5) BIOS EDD facility v0.16 2004-Jun-25, 2 devices found Freeing unused kernel memory: 244k freed input: AT Translated Set 2 keyboard as /class/input/input0 EXT3-fs: INFO: recovery required on readonly filesystem. EXT3-fs: write access will be enabled during recovery. input: ImExPS/2 Generic Explorer Mouse as /class/input/input1 kjournald starting. Commit interval 5 seconds EXT3-fs: hda8: orphan cleanup on readonly fs ext3_orphan_cleanup: deleting unreferenced inode 3960846 EXT3-fs: hda8: 1 orphan inode deleted EXT3-fs: recovery complete. EXT3-fs: mounted filesystem with ordered data mode. ts: Compaq touchscreen protocol output usbcore: registered new driver usbfs usbcore: registered new driver hub ohci_hcd: 2005 April 22 USB 1.1 'Open' Host Controller (OHCI) Driver (PCI) ACPI: PCI Interrupt Link [APCF] enabled at IRQ 23 ACPI: PCI Interrupt 0000:00:0b.0[A] -> Link [APCF] -> GSI 23 (level, low) -> IRQ 16 PCI: Setting latency timer of device 0000:00:0b.0 to 64 ohci_hcd 0000:00:0b.0: OHCI Host Controller ohci_hcd 0000:00:0b.0: new USB bus registered, assigned bus number 1 ohci_hcd 0000:00:0b.0: irq 16, io mem 0xf5104000 usb usb1: configuration #1 chosen from 1 choice hub 1-0:1.0: USB hub found hub 1-0:1.0: 8 ports detected ACPI: PCI Interrupt Link [APCL] enabled at IRQ 22 ACPI: PCI Interrupt 0000:00:0b.1[B] -> Link [APCL] -> GSI 22 (level, low) -> IRQ 17 PCI: Setting latency timer of device 0000:00:0b.1 to 64 ehci_hcd 0000:00:0b.1: EHCI Host Controller ehci_hcd 0000:00:0b.1: new USB bus registered, assigned bus number 2 ehci_hcd 0000:00:0b.1: debug port 1 PCI: cache line size of 64 is not supported by device 0000:00:0b.1 ehci_hcd 0000:00:0b.1: irq 17, io mem 0xf5100000 ehci_hcd 0000:00:0b.1: USB 2.0 started, EHCI 1.00, driver 10 Dec 2004 usb usb2: configuration #1 chosen from 1 choice hub 2-0:1.0: USB hub found hub 2-0:1.0: 8 ports detected ieee1394: Initialized config rom entry `ip1394' ACPI: PCI Interrupt Link [APC4] enabled at IRQ 19 ACPI: PCI Interrupt 0000:01:0e.0[A] -> Link [APC4] -> GSI 19 (level, low) -> IRQ 18 ohci1394: fw-host0: OHCI-1394 1.0 (PCI): IRQ=[18] MMIO=[f5000000-f50007ff] Max Packet=[2048] IR/IT contexts=[4/8] usb 2-7: new high speed USB device using ehci_hcd and address 3 usb 2-7: configuration #1 chosen from 1 choice ohci_hcd 0000:00:0b.0: wakeup SCSI subsystem initialized Initializing USB Mass Storage driver... usb 1-5: new full speed USB device using ohci_hcd and address 2 usb 1-5: configuration #1 chosen from 1 choice scsi0 : SCSI emulation for USB Mass Storage devices usb-storage: device found at 3 usb-storage: waiting for device to settle before scanning scsi1 : SCSI emulation for USB Mass Storage devices usbcore: registered new driver usb-storage USB Mass Storage support registered. usb-storage: device found at 2 usb-storage: waiting for device to settle before scanning Linux agpgart interface v0.101 © Dave Jones fuse init (API version 7.8) fuse distribution version: 2.6.3 ieee1394: Host added: ID:BUS[0-00:1023] GUID[000016e600d08b7c] powernow-k8: Found 1 AMD Athlon 64 / Opteron processors (version 1.60.2) powernow-k8: 0 : fid 0xc (2000 MHz), vid 0x2 (1500 mV) powernow-k8: 1 : fid 0xa (1800 MHz), vid 0x6 (1400 mV) powernow-k8: 2 : fid 0x2 (1000 MHz), vid 0x12 (1100 mV) cpu_init done, current fid 0xc, vid 0x2 floppy0: no floppy controllers found libata version 1.20 loaded. sata_nv 0000:00:0e.0: version 0.8 ACPI: PCI Interrupt Link [APSI] enabled at IRQ 21 ACPI: PCI Interrupt 0000:00:0e.0[A] -> Link [APSI] -> GSI 21 (level, low) -> IRQ 19 PCI: Setting latency timer of device 0000:00:0e.0 to 64 ata1: SATA max UDMA/133 cmd 0x9F0 ctl 0xBF2 bmdma 0xDC00 irq 19 ata2: SATA max UDMA/133 cmd 0x970 ctl 0xB72 bmdma 0xDC08 irq 19 ata1: SATA link down (SStatus 0) scsi2 : sata_nv ata2: SATA link down (SStatus 0) scsi3 : sata_nv device-mapper: 4.6.0-ioctl (2006-02-17) initialised: dm-devel@redhat.com EXT3 FS on hda8, internal journal Vendor: Genesys Model: CF USB Reader Rev: 9317 Type: Direct-Access ANSI SCSI revision: 00 Vendor: Genesys Model: SM USB Reader Rev: 9317 Type: Direct-Access ANSI SCSI revision: 00 Vendor: SAMSUNG Model: USB DRIVE Rev: 1.11 Type: Direct-Access ANSI SCSI revision: 01 CCS Vendor: Genesys Model: SD USB Reader Rev: 9317 Type: Direct-Access ANSI SCSI revision: 00 usb-storage: device scan complete Vendor: Genesys Model: MS USB Reader Rev: 9317 Type: Direct-Access ANSI SCSI revision: 00 sd 0:0:0:0: Attached scsi removable disk sda sd 0:0:0:1: Attached scsi removable disk sdb usb-storage: device scan complete SCSI device sdc: 125952 512-byte hdwr sectors (64 MB) sdc: Write Protect is off sdc: Mode Sense: 23 00 00 00 sdc: assuming drive cache: write through SCSI device sdc: 125952 512-byte hdwr sectors (64 MB) sdc: Write Protect is off sdc: Mode Sense: 23 00 00 00 sdc: assuming drive cache: write through sdc: sdc1 sd 1:0:0:0: Attached scsi removable disk sdc sd 0:0:0:2: Attached scsi removable disk sdd sd 0:0:0:3: Attached scsi removable disk sde sd 0:0:0:0: Attached scsi generic sg0 type 0 sd 0:0:0:1: Attached scsi generic sg1 type 0 sd 1:0:0:0: Attached scsi generic sg2 type 0 sd 0:0:0:2: Attached scsi generic sg3 type 0 sd 0:0:0:3: Attached scsi generic sg4 type 0 Adding 2658716k swap on /dev/hda9. Priority:-1 extents:1 across:2658716k kjournald starting. Commit interval 5 seconds EXT3 FS on hda7, internal journal EXT3-fs: mounted filesystem with ordered data mode. kjournald starting. Commit interval 5 seconds EXT3 FS on hda10, internal journal EXT3-fs: mounted filesystem with ordered data mode. loop: loaded (max 8 devices, max 1 partitions per device) hdc: ATAPI 48X DVD-ROM DVD-R-RAM CD-R/RW drive, 2048kB Cache, UDMA(66) Uniform CD-ROM driver Revision: 3.20 bootsplash 3.1.6-2004/03/31: looking for picture...<6> silentjpeg size 194748 bytes,<6>...found (800x600, 194700 bytes, v3). bootsplash: status on console 0 changed to on Netfilter messages via NETLINK v0.30. ACPI: Power Button (FF) [PWRF] ACPI: Power Button (CM) [PWRB] ip_conntrack version 2.4 (7679 buckets, 61432 max) - 224 bytes per conntrack Using specific hotkey driver Removing netfilter NETLINK layer. QEMU Accelerator Module version 1.3.0, Copyright © 2005-2007 Fabrice Bellard KQEMU installed, max_locked_mem=485216kB. NET: Registered protocol family 10 lo: Disabled Privacy Extensions IPv6 over IPv4 tunneling driver process `sysctl' is using deprecated sysctl (syscall) net.ipv6.neigh.lo.base_reachable_time; Use net.ipv6.neigh.lo.base_reachable_time_ms instead. NET: Registered protocol family 17 ACPI: PCI Interrupt Link [APCJ] enabled at IRQ 20 ACPI: PCI Interrupt 0000:00:10.2[C] -> Link [APCJ] -> GSI 20 (level, low) -> IRQ 20 PCI: Setting latency timer of device 0000:00:10.2 to 64 forcedeth.c: Reverse Engineered nForce ethernet driver. Version 0.54. intel8x0_measure_ac97_clock: measured 58667 usecs intel8x0: clocking to 46934 ACPI: PCI Interrupt Link [APCH] enabled at IRQ 23 ACPI: PCI Interrupt 0000:00:14.0[A] -> Link [APCH] -> GSI 23 (level, low) -> IRQ 16 PCI: Setting latency timer of device 0000:00:14.0 to 64 forcedeth: using HIGHDMA eth0: forcedeth.c: subsystem: 01458:e000 bound to 0000:00:14.0 eth0: no link during initialization. ADDRCONF(NETDEV_UP): eth0: link is not ready eth0: link up. ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready vmmon: module license 'unspecified' taints kernel. /dev/vmmon[3533]: Module vmmon: registered with major=10 minor=165 /dev/vmmon[3533]: Module vmmon: initialized parport: PnPBIOS parport detected. parport0: PC-style at 0x378 (0x778), irq 7, dma 3 [PCSPP,TRISTATE,COMPAT,ECP,DMA] ip_tables: © 2000-2006 Netfilter Core Team /dev/vmnet: open called by PID 3975 (vmnet-bridge) /dev/vmnet: hub 0 does not exist, allocating memory. /dev/vmnet: port on hub 0 successfully opened bridge-eth0: enabling the bridge bridge-eth0: up bridge-eth0: already up bridge-eth0: attached /dev/vmnet: open called by PID 3995 (vmnet-natd) /dev/vmnet: hub 8 does not exist, allocating memory. /dev/vmnet: port on hub 8 successfully opened Netfilter messages via NETLINK v0.30. ip_conntrack version 2.4 (7679 buckets, 61432 max) - 224 bytes per conntrack /dev/vmnet: open called by PID 4170 (vmnet-netifup) /dev/vmnet: hub 1 does not exist, allocating memory. /dev/vmnet: port on hub 1 successfully opened /dev/vmnet: open called by PID 4171 (vmnet-netifup) /dev/vmnet: port on hub 8 successfully opened ip_conntrack_pptp version 3.1 loaded /dev/vmnet: open called by PID 4192 (vmnet-dhcpd) /dev/vmnet: port on hub 8 successfully opened /dev/vmnet: open called by PID 4204 (vmnet-dhcpd) /dev/vmnet: port on hub 1 successfully opened ACPI: PCI Interrupt Link [APC7] enabled at IRQ 16 ACPI: PCI Interrupt 0000:00:05.0[A] -> Link [APC7] -> GSI 16 (level, low) -> IRQ 21 PCI: Setting latency timer of device 0000:00:05.0 to 64 NVRM: loading NVIDIA UNIX x86 Kernel Module 1.0-9755 Mon Feb 26 23:21:15 PST 2007 eth0: no IPv6 routers present ip_nat_pptp version 3.0 loaded ClusterIP Version 0.8 loaded successfully ipt_recent v0.3.1: Stephen Frost <sfrost@snowman.net>. http://snowman.net/projects/ipt_recent/ floppy0: no floppy controllers found eth1394: eth1: IEEE-1394 IPv4 over 1394 Ethernet (fw-host0) Shorewall:OUTPUT:REJECT:IN= OUT=vmnet1 SRC=192.168.150.1 DST=224.0.0.251 LEN=169 TOS=0x00 PREC=0x00 TTL=255 ID=0 DF PROTO=UDP SPT=5353 DPT=5353 LEN=149 Shorewall:OUTPUT:REJECT:IN= OUT=vmnet8 SRC=192.168.17.1 DST=224.0.0.251 LEN=169 TOS=0x00 PREC=0x00 TTL=255 ID=0 DF PROTO=UDP SPT=5353 DPT=5353 LEN=149 netfilter PSD loaded - © astaro AG IFWLOG: register target bootsplash 3.1.6-2004/03/31: looking for picture...<6>...found (800x600, 14222 bytes, v3). bootsplash: status on console 0 changed to on bootsplash 3.1.6-2004/03/31: looking for picture...<6>...found (800x600, 14222 bytes, v3). bootsplash: status on console 1 changed to on bootsplash 3.1.6-2004/03/31: looking for picture...<6>...found (800x600, 14222 bytes, v3). bootsplash: status on console 2 changed to on bootsplash 3.1.6-2004/03/31: looking for picture...<6>...found (800x600, 14222 bytes, v3). bootsplash: status on console 3 changed to on bootsplash 3.1.6-2004/03/31: looking for picture...<6>...found (800x600, 14222 bytes, v3). bootsplash: status on console 4 changed to on bootsplash 3.1.6-2004/03/31: looking for picture...<6>...found (800x600, 14222 bytes, v3). bootsplash: status on console 5 changed to on Shorewall:OUTPUT:REJECT:IN= OUT=vmnet8 SRC=192.168.17.1 DST=224.0.0.22 LEN=40 TOS=0x00 PREC=0xC0 TTL=1 ID=0 DF PROTO=2 floppy0: no floppy controllers found ppdev: user-space parallel port driver Device not ready. Make sure there is a disc in the drive. Device not ready. Make sure there is a disc in the drive. Device not ready. Make sure there is a disc in the drive. Device not ready. Make sure there is a disc in the drive. Device not ready. Make sure there is a disc in the drive. Device not ready. Make sure there is a disc in the drive. Device not ready. Make sure there is a disc in the drive. Device not ready. Make sure there is a disc in the drive. vmnet1: no IPv6 routers present vmnet8: no IPv6 routers present Shorewall:net2all:DROP:IN=eth0 OUT= MAC=00:16:e6:68:2d:72:00:e0:4c:a0:5e:b7:08:00 SRC=192.168.0.1 DST=192.168.0.108 LEN=92 TOS=0x00 PREC=0x00 TTL=64 ID=0 DF PROTO=ICMP TYPE=8 CODE=0 ID=48991 SEQ=0 Shorewall:net2all:DROP:IN=eth0 OUT= MAC=00:16:e6:68:2d:72:00:e0:4c:a0:5e:b7:08:00 SRC=192.168.0.1 DST=192.168.0.108 LEN=92 TOS=0x00 PREC=0x00 TTL=64 ID=0 DF PROTO=ICMP TYPE=8 CODE=0 ID=48991 SEQ=0 Shorewall:net2all:DROP:IN=eth0 OUT= MAC=00:16:e6:68:2d:72:00:e0:4c:a0:5e:b7:08:00 SRC=192.168.0.1 DST=192.168.0.108 LEN=92 TOS=0x00 PREC=0x00 TTL=64 ID=0 DF PROTO=ICMP TYPE=8 CODE=0 ID=48991 SEQ=0 Shorewall:net2all:DROP:IN=eth0 OUT= MAC=00:16:e6:68:2d:72:00:e0:4c:a0:5e:b7:08:00 SRC=192.168.0.1 DST=192.168.0.108 LEN=92 TOS=0x00 PREC=0x00 TTL=64 ID=0 DF PROTO=ICMP TYPE=8 CODE=0 ID=48991 SEQ=0 Shorewall:net2all:DROP:IN=eth0 OUT= MAC=00:16:e6:68:2d:72:00:e0:4c:a0:5e:b7:08:00 SRC=192.168.0.1 DST=192.168.0.108 LEN=92 TOS=0x00 PREC=0x00 TTL=64 ID=0 DF PROTO=ICMP TYPE=8 CODE=0 ID=48991 SEQ=0 Shorewall:net2all:DROP:IN=eth0 OUT= MAC=00:16:e6:68:2d:72:00:e0:4c:a0:5e:b7:08:00 SRC=192.168.0.1 DST=192.168.0.108 LEN=92 TOS=0x00 PREC=0x00 TTL=64 ID=0 DF PROTO=ICMP TYPE=8 CODE=0 ID=48991 SEQ=0 Shorewall:net2all:DROP:IN=eth0 OUT= MAC=00:16:e6:68:2d:72:00:e0:4c:a0:5e:b7:08:00 SRC=192.168.0.1 DST=192.168.0.108 LEN=92 TOS=0x00 PREC=0x00 TTL=64 ID=0 DF PROTO=ICMP TYPE=8 CODE=0 ID=48991 SEQ=0 Shorewall:net2all:DROP:IN=eth0 OUT= MAC=00:16:e6:68:2d:72:00:e0:4c:a0:5e:b7:08:00 SRC=192.168.0.1 DST=192.168.0.108 LEN=92 TOS=0x00 PREC=0x00 TTL=64 ID=0 DF PROTO=ICMP TYPE=8 CODE=0 ID=48991 SEQ=0 Shorewall:net2all:DROP:IN=eth0 OUT= MAC=00:16:e6:68:2d:72:00:e0:4c:a0:5e:b7:08:00 SRC=192.168.0.1 DST=192.168.0.108 LEN=92 TOS=0x00 PREC=0x00 TTL=64 ID=0 DF PROTO=ICMP TYPE=8 CODE=0 ID=48991 SEQ=0 Shorewall:net2all:DROP:IN=eth0 OUT= MAC=00:16:e6:68:2d:72:00:e0:4c:a0:5e:b7:08:00 SRC=192.168.0.1 DST=192.168.0.108 LEN=92 TOS=0x00 PREC=0x00 TTL=64 ID=0 DF PROTO=ICMP TYPE=8 CODE=0 ID=48991 SEQ=0 Shorewall:net2all:DROP:IN=eth0 OUT= MAC=00:16:e6:68:2d:72:00:e0:4c:a0:5e:b7:08:00 SRC=192.168.0.1 DST=192.168.0.108 LEN=92 TOS=0x00 PREC=0x00 TTL=64 ID=0 DF PROTO=ICMP TYPE=8 CODE=0 ID=48991 SEQ=0 Shorewall:net2all:DROP:IN=eth0 OUT= MAC=00:16:e6:68:2d:72:00:e0:4c:a0:5e:b7:08:00 SRC=192.168.0.1 DST=192.168.0.108 LEN=92 TOS=0x00 PREC=0x00 TTL=64 ID=0 DF PROTO=ICMP TYPE=8 CODE=0 ID=48991 SEQ=0 Shorewall:net2all:DROP:IN=eth0 OUT= MAC=00:16:e6:68:2d:72:00:e0:4c:a0:5e:b7:08:00 SRC=192.168.0.1 DST=192.168.0.108 LEN=92 TOS=0x00 PREC=0x00 TTL=64 ID=0 DF PROTO=ICMP TYPE=8 CODE=0 ID=48991 SEQ=0 Shorewall:net2all:DROP:IN=eth0 OUT= MAC=00:16:e6:68:2d:72:00:e0:4c:a0:5e:b7:08:00 SRC=192.168.0.1 DST=192.168.0.108 LEN=92 TOS=0x00 PREC=0x00 TTL=64 ID=0 DF PROTO=ICMP TYPE=8 CODE=0 ID=48991 SEQ=0 Shorewall:net2all:DROP:IN=eth0 OUT= MAC=00:16:e6:68:2d:72:00:e0:4c:a0:5e:b7:08:00 SRC=192.168.0.1 DST=192.168.0.108 LEN=92 TOS=0x00 PREC=0x00 TTL=64 ID=0 DF PROTO=ICMP TYPE=8 CODE=0 ID=48991 SEQ=0 Shorewall:net2all:DROP:IN=eth0 OUT= MAC=00:16:e6:68:2d:72:00:e0:4c:a0:5e:b7:08:00 SRC=192.168.0.1 DST=192.168.0.108 LEN=92 TOS=0x00 PREC=0x00 TTL=64 ID=0 DF PROTO=ICMP TYPE=8 CODE=0 ID=48991 SEQ=0 Shorewall:net2all:DROP:IN=eth0 OUT= MAC=00:16:e6:68:2d:72:00:e0:4c:a0:5e:b7:08:00 SRC=192.168.0.1 DST=192.168.0.108 LEN=92 TOS=0x00 PREC=0x00 TTL=64 ID=0 DF PROTO=ICMP TYPE=8 CODE=0 ID=48991 SEQ=0 Shorewall:net2all:DROP:IN=eth0 OUT= MAC=00:16:e6:68:2d:72:00:e0:4c:a0:5e:b7:08:00 SRC=192.168.0.1 DST=192.168.0.108 LEN=92 TOS=0x00 PREC=0x00 TTL=64 ID=0 DF PROTO=ICMP TYPE=8 CODE=0 ID=48991 SEQ=0 Shorewall:net2all:DROP:IN=eth0 OUT= MAC=00:16:e6:68:2d:72:00:e0:4c:a0:5e:b7:08:00 SRC=192.168.0.1 DST=192.168.0.108 LEN=92 TOS=0x00 PREC=0x00 TTL=64 ID=0 DF PROTO=ICMP TYPE=8 CODE=0 ID=48991 SEQ=0 Shorewall:net2all:DROP:IN=eth0 OUT= MAC=00:16:e6:68:2d:72:00:e0:4c:a0:5e:b7:08:00 SRC=192.168.0.1 DST=192.168.0.108 LEN=92 TOS=0x00 PREC=0x00 TTL=64 ID=0 DF PROTO=ICMP TYPE=8 CODE=0 ID=48991 SEQ=0 Shorewall:net2all:DROP:IN=eth0 OUT= MAC=00:16:e6:68:2d:72:00:e0:4c:a0:5e:b7:08:00 SRC=192.168.0.1 DST=192.168.0.108 LEN=92 TOS=0x00 PREC=0x00 TTL=64 ID=0 DF PROTO=ICMP TYPE=8 CODE=0 ID=48991 SEQ=0 usb 2-7: USB disconnect, address 3 usb 2-7: new high speed USB device using ehci_hcd and address 4 usb 2-7: device not accepting address 4, error -71 Shorewall:net2all:DROP:IN=eth0 OUT= MAC=00:16:e6:68:2d:72:00:e0:4c:a0:5e:b7:08:00 SRC=192.168.0.1 DST=192.168.0.108 LEN=92 TOS=0x00 PREC=0x00 TTL=64 ID=0 DF PROTO=ICMP TYPE=8 CODE=0 ID=48991 SEQ=0 hub 2-0:1.0: Cannot enable port 7. Maybe the USB cable is bad? usb 2-7: new high speed USB device using ehci_hcd and address 6 usb 2-7: configuration #1 chosen from 1 choice scsi4 : SCSI emulation for USB Mass Storage devices usb-storage: device found at 6 usb-storage: waiting for device to settle before scanning usb 2-7: USB disconnect, address 6 usb 2-7: new high speed USB device using ehci_hcd and address 7 usb 2-7: configuration #1 chosen from 1 choice scsi5 : SCSI emulation for USB Mass Storage devices usb-storage: device found at 7 usb-storage: waiting for device to settle before scanning usb 2-8: new high speed USB device using ehci_hcd and address 8 usb 2-8: configuration #1 chosen from 2 choices Vendor: Genesys Model: CF USB Reader Rev: 9317 Type: Direct-Access ANSI SCSI revision: 00 sd 5:0:0:0: Attached scsi removable disk sda sd 5:0:0:0: Attached scsi generic sg0 type 0 Vendor: Genesys Model: SM USB Reader Rev: 9317 Type: Direct-Access ANSI SCSI revision: 00 sd 5:0:0:1: Attached scsi removable disk sdb sd 5:0:0:1: Attached scsi generic sg1 type 0 Vendor: Genesys Model: SD USB Reader Rev: 9317 Type: Direct-Access ANSI SCSI revision: 00 sd 5:0:0:2: Attached scsi removable disk sdd sd 5:0:0:2: Attached scsi generic sg3 type 0 Vendor: Genesys Model: MS USB Reader Rev: 9317 Type: Direct-Access ANSI SCSI revision: 00 sd 5:0:0:3: Attached scsi removable disk sde sd 5:0:0:3: Attached scsi generic sg4 type 0 usb-storage: device scan complete usb 2-8: USB disconnect, address 8 Shorewall:net2all:DROP:IN=eth0 OUT= MAC=00:16:e6:68:2d:72:00:e0:4c:a0:5e:b7:08:00 SRC=192.168.0.1 DST=192.168.0.108 LEN=92 TOS=0x00 PREC=0x00 TTL=64 ID=0 DF PROTO=ICMP TYPE=8 CODE=0 ID=48991 SEQ=0 usb 2-8: new high speed USB device using ehci_hcd and address 9 usb 2-8: configuration #1 chosen from 2 choices Shorewall:net2all:DROP:IN=eth0 OUT= MAC=00:16:e6:68:2d:72:00:e0:4c:a0:5e:b7:08:00 SRC=192.168.0.1 DST=192.168.0.108 LEN=92 TOS=0x00 PREC=0x00 TTL=64 ID=0 DF PROTO=ICMP TYPE=8 CODE=0 ID=48991 SEQ=0 Shorewall:net2all:DROP:IN=eth0 OUT= MAC=00:16:e6:68:2d:72:00:e0:4c:a0:5e:b7:08:00 SRC=192.168.0.1 DST=192.168.0.108 LEN=92 TOS=0x00 PREC=0x00 TTL=64 ID=0 DF PROTO=ICMP TYPE=8 CODE=0 ID=48991 SEQ=0 Shorewall:net2all:DROP:IN=eth0 OUT= MAC=00:16:e6:68:2d:72:00:e0:4c:a0:5e:b7:08:00 SRC=192.168.0.1 DST=192.168.0.108 LEN=92 TOS=0x00 PREC=0x00 TTL=64 ID=0 DF PROTO=ICMP TYPE=8 CODE=0 ID=48991 SEQ=0

[HAW]

а в digikam не открывается?

[Juliette]

а в digikam не открывается?

Короче да, вроде всё определяется, теперь просто надо попробовать запустить программульку какую-нибудь, типа digikam или gtkam и попробовать выбрать там из списка.

[Kitovras]

а в digikam не открывается?

Короче да, вроде всё определяется, теперь просто надо попробовать запустить программульку какую-нибудь, типа digikam или gtkam и попробовать выбрать там из списка.

А так, чтобы примонтировать как флешку нельзя ?

[Juliette]

А так, чтобы примонтировать как флешку нельзя ?

неа
только работать из-под спец. программы

[Kitovras]

неа
только работать из-под спец. программы

Спасибо. Попробую вечером.