Подружить Mass Storage Eonstar с дебианом

[zavorot_kostey]

Имеется масс сторейдж на 16 винтов - A16U-G2430. Она подключена к контроллеру Adaptec ASC-29320ALP U320. Проблема в том, что она как-то странно работает с линуксом: ее то видно, то не видно.
lspci:

Код: Выделить всё

00:00.0 Host bridge: IBM Winnipeg PCI-X Host Bridge (rev 03)
00:01.0 VGA compatible controller: S3 Inc. Savage 4 (rev 06)
00:02.0 Bridge: IBM Remote Supervisor Adapter (RSA)
00:03.0 Ethernet controller: Intel Corporation 82557/8/9 [Ethernet Pro 100] (rev 08)
00:06.0 Generic system peripheral [0808]: IBM Unknown device 0246
00:0f.0 ISA bridge: Broadcom OSB4 South Bridge (rev 50)
00:0f.1 IDE interface: Broadcom OSB4 IDE Controller
00:0f.2 USB Controller: Broadcom OSB4/CSB5 OHCI USB Controller (rev 04)
01:00.0 Host bridge: IBM Winnipeg PCI-X Host Bridge (rev 03)
01:02.0 SCSI storage controller: Adaptec ASC-29320ALP U320 (rev 10)
0a:00.0 Host bridge: IBM Winnipeg PCI-X Host Bridge (rev 03)
0a:01.0 RAID bus controller: IBM ServeRAID Controller
0a:02.0 Ethernet controller: Intel Corporation 82545EM Gigabit Ethernet Controller (Copper) (rev 01)

lshw:

Код: Выделить всё

     *-scsi:0
          physical id: 1
          logical name: scsi0
        *-disk UNCLAIMED
             description: SCSI Disk
             physical id: 0.c.0
             bus info: scsi@0:0.12.0
     *-scsi:1
          physical id: 2
          logical name: scsi1
          capabilities: scsi-host
          configuration: driver=ips
        *-disk
             description: SCSI Disk
             product: SERVERAID
             vendor: IBM
             physical id: 0.0.0
             bus info: scsi@1:0.0.0
             logical name: /dev/sdb
             version: 1.00
             size: 136GB
             capabilities: partitioned partitioned:dos
             configuration: ansiversion=2
           *-volume:0
                description: Linux filesystem partition
                physical id: 1
                bus info: scsi@1:0.0.0,1
                logical name: /dev/sdb1
                capacity: 6675MB
                capabilities: primary bootable
           *-volume:1
                description: Extended partition
                physical id: 2
                bus info: scsi@1:0.0.0,2
                logical name: /dev/sdb2
                size: 130GB
                capacity: 130GB
                capabilities: primary extended partitioned partitioned:extended
              *-logicalvolume:0
                   description: Linux swap / Solaris partition
                   physical id: 5
                   logical name: /dev/sdb5
                   capacity: 2588MB
                   capabilities: nofs
              *-logicalvolume:1
                   description: Linux filesystem partition
                   physical id: 6
                   logical name: /dev/sdb6
                   capacity: 127GB
        *-processor:0 UNCLAIMED
             description: SCSI Processor
             product: SERVERAID
             vendor: IBM
             physical id: 0.f.0
             bus info: scsi@1:0.15.0
             version: 1.00
             configuration: ansiversion=2
        *-processor:1 UNCLAIMED
             description: SCSI Processor
             product: YGHv3 S2
             vendor: IBM
             physical id: 1.9.0
             bus info: scsi@1:1.9.0
             version: 0
             serial: 1
             configuration: ansiversion=2
     *-scsi:2
          physical id: 3
          logical name: scsi2
          capabilities: scsi-host
          configuration: driver=scsi_debug
        *-disk
             description: SCSI Disk
             product: scsi_debug
             vendor: Linux
             physical id: 0.0.0
             bus info: scsi@2:0.0.0
             logical name: /dev/sdc
             version: 0004
             serial: 6000
             size: 8MB
             configuration: ansiversion=5

Однако когда я хочу создать раздел - получаю:

Код: Выделить всё

major:/home/nikitad# fdisk /dev/sda

Unable to open /dev/sda

Проблема однозначно с масс сторейджом, ибо SCSI контроллер видиться и определяется нормально. Есть у кого мысли?