Bootdata ok (command line is root=/dev/md1 ro )
Linux version 2.6.18-4-amd64 (Debian 2.6.18.dfsg.1-12) (waldi@debian.org) (gcc version 4.1.2 20061115 (prerelease) (Debian 4.1.1-21)) #1 SMP Mon Mar 26 11:36:53 CEST 2007
BIOS-provided physical RAM map:
BIOS-e820: 0000000000000000 - 000000000009ec00 (usable)
BIOS-e820: 000000000009ec00 - 00000000000a0000 (reserved)
BIOS-e820: 00000000000f0000 - 0000000000100000 (reserved)
BIOS-e820: 0000000000100000 - 000000007feb0000 (usable)
BIOS-e820: 000000007feb0000 - 000000007fee3000 (ACPI NVS)
BIOS-e820: 000000007fee3000 - 000000007fef0000 (ACPI data)
BIOS-e820: 000000007fef0000 - 000000007ff00000 (reserved)
BIOS-e820: 00000000f0000000 - 00000000f4000000 (reserved)
BIOS-e820: 00000000fec00000 - 0000000100000000 (reserved)
DMI 2.3 present.
ACPI: RSDP (v000 Nvidia ) @ 0x00000000000f7e40
ACPI: RSDT (v001 Nvidia AWRDACPI 0x42302e31 AWRD 0x00000000) @ 0x000000007fee3040
ACPI: FADT (v001 Nvidia AWRDACPI 0x42302e31 AWRD 0x00000000) @ 0x000000007fee30c0
ACPI: TCPA (v001 HTC HTCACPI 0x42302e31 AWRD 0x00000000) @ 0x000000007feec580
ACPI: MCFG (v001 Nvidia AWRDACPI 0x42302e31 AWRD 0x00000000) @ 0x000000007feec600
ACPI: MADT (v001 Nvidia AWRDACPI 0x42302e31 AWRD 0x00000000) @ 0x000000007feec4c0
ACPI: DSDT (v001 NVIDIA AWRDACPI 0x00001000 MSFT 0x0100000e) @ 0x0000000000000000
Scanning NUMA topology in Northbridge 24
Number of nodes 1
Node 0 MemBase 0000000000000000 Limit 000000007feb0000
NUMA: Using 63 for the hash shift.
Using node hash shift of 63
Bootmem setup node 0 0000000000000000-000000007feb0000
On node 0 totalpages: 515803
DMA zone: 3054 pages, LIFO batch:0
DMA32 zone: 512749 pages, LIFO batch:31
Nvidia board detected. Ignoring ACPI timer override.
ACPI: PM-Timer IO Port: 0x1008
ACPI: Local APIC address 0xfee00000
ACPI: LAPIC (acpi_id[0x00] lapic_id[0x00] enabled)
Processor #0 15:3 APIC version 16
ACPI: LAPIC (acpi_id[0x01] lapic_id[0x01] enabled)
Processor #1 15:3 APIC version 16
ACPI: LAPIC_NMI (acpi_id[0x00] high edge lint[0x1])
ACPI: LAPIC_NMI (acpi_id[0x01] high edge lint[0x1])
ACPI: IOAPIC (id[0x02] address[0xfec00000] gsi_base[0])
IOAPIC[0]: apic_id 2, version 17, address 0xfec00000, GSI 0-23
ACPI: INT_SRC_OVR (bus 0 bus_irq 9 global_irq 9 high level)
ACPI: INT_SRC_OVR (bus 0 bus_irq 14 global_irq 14 high edge)
ACPI: INT_SRC_OVR (bus 0 bus_irq 15 global_irq 15 high edge)
ACPI: IRQ9 used by override.
ACPI: IRQ14 used by override.
ACPI: IRQ15 used by override.
Setting APIC routing to physical flat
Using ACPI (MADT) for SMP configuration information
Allocating PCI resources starting at 80000000 (gap: 7ff00000:70100000)
SMP: Allowing 2 CPUs, 0 hotplug CPUs
Built 1 zonelists. Total pages: 515803
Kernel command line: root=/dev/md1 ro
Initializing CPU#0
PID hash table entries: 4096 (order: 12, 32768 bytes)
Disabling vsyscall due to use of PM timer
time.c: Using 3.579545 MHz WALL PM GTOD PM timer.
time.c: Detected 2612.082 MHz processor.
Console: colour VGA+ 80x25
Dentry cache hash table entries: 262144 (order: 9, 2097152 bytes)
Inode-cache hash table entries: 131072 (order: 8, 1048576 bytes)
Checking aperture...
CPU 0: aperture @ e4a000000 size 32 MB
Aperture too small (32 MB)
No AGP bridge found
Memory: 2054328k/2095808k available (1930k kernel code, 41088k reserved, 868k data, 176k init)
Calibrating delay using timer specific routine.. 5229.65 BogoMIPS (lpj=10459305)
Security Framework v1.0.0 initialized
SELinux: Disabled at boot.
Capability LSM initialized
Mount-cache hash table entries: 256
CPU: L1 I Cache: 64K (64 bytes/line), D cache 64K (64 bytes/line)
CPU: L2 Cache: 1024K (64 bytes/line)
CPU 0/0 -> Node 0
CPU: Physical Processor ID: 0
CPU: Processor Core ID: 0
SMP alternatives: switching to UP code
ACPI: Core revision 20060707
Using local APIC timer interrupts.
result 12558104
Detected 12.558 MHz APIC timer.
SMP alternatives: switching to SMP code
Booting processor 1/2 APIC 0x1
Initializing CPU#1
Calibrating delay using timer specific routine.. 5224.43 BogoMIPS (lpj=10448870)
CPU: L1 I Cache: 64K (64 bytes/line), D cache 64K (64 bytes/line)
CPU: L2 Cache: 1024K (64 bytes/line)
CPU 1/1 -> Node 0
CPU: Physical Processor ID: 0
CPU: Processor Core ID: 1
AMD Athlon 64 X2 Dual Core Processor 5200+ stepping 02
CPU 1: Syncing TSC to CPU 0.
CPU 1: synchronized TSC with CPU 0 (last diff 0 cycles, maxerr 548 cycles)
Brought up 2 CPUs
testing NMI watchdog ... OK.
migration_cost=310
checking if image is initramfs... it is
Freeing initrd memory: 5633k freed
NET: Registered protocol family 16
ACPI: bus type pci registered
PCI: Using MMCONFIG at f0000000
PCI: No mmconfig possible on device 0:18
ACPI: Interpreter enabled
ACPI: Using IOAPIC for interrupt routing
ACPI: PCI Root Bridge [PCI0] (0000:00)
PCI: Probing PCI hardware (bus 00)
Boot video device is 0000:01:00.0
PCI: Transparent bridge - 0000:00:0e.0
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0._PRT]
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.HUB0._PRT]
ACPI: PCI Interrupt Link [LNK1] (IRQs 5 7 9 10 11 14 15) *0, disabled.
ACPI: PCI Interrupt Link [LNK2] (IRQs 5 7 9 10 11 14 15) *0, disabled.
ACPI: PCI Interrupt Link [LNK3] (IRQs 5 7 9 10 11 14 15) *0, disabled.
ACPI: PCI Interrupt Link [LNK4] (IRQs 5 7 9 10 *11 14 15)
ACPI: PCI Interrupt Link [LNK5] (IRQs 5 7 9 *10 11 14 15)
ACPI: PCI Interrupt Link [LNK6] (IRQs 5 7 9 10 *11 14 15)
ACPI: PCI Interrupt Link [LNK7] (IRQs *5 7 9 10 11 14 15)
ACPI: PCI Interrupt Link [LNK8] (IRQs 5 7 9 10 11 14 15) *0, disabled.
ACPI: PCI Interrupt Link [LP2P] (IRQs 5 7 9 10 11 14 15) *0, disabled.
ACPI: PCI Interrupt Link [LUBA] (IRQs 5 *7 9 10 11 14 15)
ACPI: PCI Interrupt Link [LMAC] (IRQs *5 7 9 10 11 14 15)
ACPI: PCI Interrupt Link [LMC1] (IRQs 5 7 9 *10 11 14 15)
ACPI: PCI Interrupt Link [LAZA] (IRQs 5 7 9 10 *11 14 15)
ACPI: PCI Interrupt Link [LPMU] (IRQs 5 7 9 10 11 14 15) *0, disabled.
ACPI: PCI Interrupt Link [LSMB] (IRQs 5 7 9 10 *11 14 15)
ACPI: PCI Interrupt Link [LUB2] (IRQs 5 7 9 *10 11 14 15)
ACPI: PCI Interrupt Link [LIDE] (IRQs 5 7 9 10 11 14 15) *0, disabled.
ACPI: PCI Interrupt Link [LSID] (IRQs *5 7 9 10 11 14 15)
ACPI: PCI Interrupt Link [LFID] (IRQs *5 7 9 10 11 14 15)
ACPI: PCI Interrupt Link [LSA2] (IRQs *5 7 9 10 11 14 15)
ACPI: PCI Interrupt Link [APC1] (IRQs 16) *0, disabled.
ACPI: PCI Interrupt Link [APC2] (IRQs 17) *0, disabled.
ACPI: PCI Interrupt Link [APC3] (IRQs 18) *0, disabled.
ACPI: PCI Interrupt Link [APC4] (IRQs 19) *0, disabled.
ACPI: PCI Interrupt Link [APC5] (IRQs 16) *0, disabled.
ACPI: PCI Interrupt Link [APC6] (IRQs 16) *0, disabled.
ACPI: PCI Interrupt Link [APC7] (IRQs 16) *0, disabled.
ACPI: PCI Interrupt Link [APC8] (IRQs 16) *0, disabled.
ACPI: PCI Interrupt Link [APCF] (IRQs 20 21 22 23) *0, disabled.
ACPI: PCI Interrupt Link [APCH] (IRQs 20 21 22 23) *0, disabled.
ACPI: PCI Interrupt Link [AMC1] (IRQs 20 21 22 23) *0, disabled.
ACPI: PCI Interrupt Link [APMU] (IRQs 20 21 22 23) *0, disabled.
ACPI: PCI Interrupt Link [AAZA] (IRQs 20 21 22 23) *0, disabled.
ACPI: PCI Interrupt Link [APCS] (IRQs 20 21 22 23) *0, disabled.
ACPI: PCI Interrupt Link [APCL] (IRQs 20 21 22 23) *0, disabled.
ACPI: PCI Interrupt Link [APCM] (IRQs 20 21 22 23) *0, disabled.
ACPI: PCI Interrupt Link [APCZ] (IRQs 20 21 22 23) *0, disabled.
ACPI: PCI Interrupt Link [APSI] (IRQs 20 21 22 23) *0, disabled.
ACPI: PCI Interrupt Link [APSJ] (IRQs 20 21 22 23) *0, disabled.
ACPI: PCI Interrupt Link [ASA2] (IRQs 20 21 22 23) *0, disabled.
Linux Plug and Play Support v0.97 © Adam Belay
pnp: PnP ACPI init
pnp: ACPI device : hid PNP0A08
pnp: ACPI device : hid PNP0C02
pnp: ACPI device : hid PNP0C02
pnp: ACPI device : hid PNP0200
pnp: ACPI device : hid PNP0B00
pnp: ACPI device : hid PNP0800
pnp: ACPI device : hid PNP0C04
pnp: ACPI device : hid PNP0700
pnp: ACPI device : hid PNP0501
pnp: ACPI device : hid PNP0401
pnp: ACPI device : hid PNP0C02
pnp: ACPI device : hid PNP0C01
pnp: PnP ACPI: found 12 devices
usbcore: registered new driver usbfs
usbcore: registered new driver hub
PCI: Using ACPI for IRQ routing
PCI: If a device doesn't work, try "pci=routeirq". If it helps, post a report
PCI-DMA: Disabling IOMMU.
pnp: the driver 'system' has been registered
pnp: match found with the PnP device '00:01' and the driver 'system'
pnp: 00:01: ioport range 0x1000-0x107f could not be reserved
pnp: 00:01: ioport range 0x1080-0x10ff has been reserved
pnp: 00:01: ioport range 0x1400-0x147f has been reserved
pnp: 00:01: ioport range 0x1480-0x14ff could not be reserved
pnp: 00:01: ioport range 0x1800-0x187f has been reserved
pnp: 00:01: ioport range 0x1880-0x18ff has been reserved
pnp: match found with the PnP device '00:02' and the driver 'system'
pnp: match found with the PnP device '00:0a' and the driver 'system'
pnp: match found with the PnP device '00:0b' and the driver 'system'
PCI: Bridge: 0000:00:04.0
IO window: disabled.
MEM window: fa000000-fcffffff
PREFETCH window: e0000000-efffffff
PCI: Bridge: 0000:00:0e.0
IO window: disabled.
MEM window: fdf00000-fdffffff
PREFETCH window: disabled.
PCI: Bridge: 0000:03:00.0
IO window: 9000-9fff
MEM window: fdd00000-fddfffff
PREFETCH window: 80000000-800fffff
PCI: Bridge: 0000:03:00.1
IO window: disabled.
MEM window: disabled.
PREFETCH window: disabled.
PCI: Bridge: 0000:00:12.0
IO window: 9000-9fff
MEM window: fdd00000-fdefffff
PREFETCH window: 80000000-800fffff
PCI: Bridge: 0000:00:14.0
IO window: disabled.
MEM window: disabled.
PREFETCH window: disabled.
PCI: Bridge: 0000:00:15.0
IO window: disabled.
MEM window: disabled.
PREFETCH window: disabled.
PCI: Bridge: 0000:00:16.0
IO window: 8000-8fff
MEM window: fdc00000-fdcfffff
PREFETCH window: disabled.
PCI: Bridge: 0000:00:17.0
IO window: disabled.
MEM window: disabled.
PREFETCH window: disabled.
PCI: Setting latency timer of device 0000:00:04.0 to 64
PCI: Setting latency timer of device 0000:00:0e.0 to 64
PCI: Setting latency timer of device 0000:00:12.0 to 64
PCI: Setting latency timer of device 0000:03:00.0 to 64
ACPI: PCI Interrupt Link [APC7] enabled at IRQ 16
GSI 16 sharing vector 0xB1 and IRQ 16
ACPI: PCI Interrupt 0000:03:00.1[A] -> Link [APC7] -> GSI 16 (level, low) -> IRQ 177
PCI: Setting latency timer of device 0000:03:00.1 to 64
PCI: Setting latency timer of device 0000:00:14.0 to 64
PCI: Setting latency timer of device 0000:00:15.0 to 64
PCI: Setting latency timer of device 0000:00:16.0 to 64
PCI: Setting latency timer of device 0000:00:17.0 to 64
NET: Registered protocol family 2
IP route cache hash table entries: 65536 (order: 7, 524288 bytes)
TCP established hash table entries: 262144 (order: 10, 4194304 bytes)
TCP bind hash table entries: 65536 (order: 8, 1048576 bytes)
TCP: Hash tables configured (established 262144 bind 65536)
TCP reno registered
audit: initializing netlink socket (disabled)
audit(1199912402.568:1): initialized
VFS: Disk quotas dquot_6.5.1
Dquot-cache hash table entries: 512 (order 0, 4096 bytes)
Initializing Cryptographic API
io scheduler noop registered
io scheduler anticipatory registered
io scheduler deadline registered
io scheduler cfq registered (default)
PCI: Setting latency timer of device 0000:00:04.0 to 64
pcie_portdrv_probe->Dev[02fb:10de] has invalid IRQ. Check vendor BIOS
assign_interrupt_mode Found MSI capability
Allocate Port Service[0000:00:04.0:pcie00]
Allocate Port Service[0000:00:04.0:pcie03]
PCI: Setting latency timer of device 0000:00:12.0 to 64
pcie_portdrv_probe->Dev[0376:10de] has invalid IRQ. Check vendor BIOS
assign_interrupt_mode Found MSI capability
Allocate Port Service[0000:00:12.0:pcie00]
Allocate Port Service[0000:00:12.0:pcie03]
PCI: Setting latency timer of device 0000:00:14.0 to 64
pcie_portdrv_probe->Dev[0374:10de] has invalid IRQ. Check vendor BIOS
assign_interrupt_mode Found MSI capability
Allocate Port Service[0000:00:14.0:pcie00]
Allocate Port Service[0000:00:14.0:pcie03]
PCI: Setting latency timer of device 0000:00:15.0 to 64
pcie_portdrv_probe->Dev[0378:10de] has invalid IRQ. Check vendor BIOS
assign_interrupt_mode Found MSI capability
Allocate Port Service[0000:00:15.0:pcie00]
Allocate Port Service[0000:00:15.0:pcie03]
PCI: Setting latency timer of device 0000:00:16.0 to 64
pcie_portdrv_probe->Dev[0375:10de] has invalid IRQ. Check vendor BIOS
assign_interrupt_mode Found MSI capability
Allocate Port Service[0000:00:16.0:pcie00]
Allocate Port Service[0000:00:16.0:pcie03]
PCI: Setting latency timer of device 0000:00:17.0 to 64
pcie_portdrv_probe->Dev[0377:10de] has invalid IRQ. Check vendor BIOS
assign_interrupt_mode Found MSI capability
Allocate Port Service[0000:00:17.0:pcie00]
Allocate Port Service[0000:00:17.0:pcie03]
Real Time Clock Driver v1.12ac
Linux agpgart interface v0.101 © Dave Jones
Serial: 8250/16550 driver $Revision: 1.90 $ 4 ports, IRQ sharing enabled
serial8250: ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A
pnp: the driver 'serial' has been registered
pnp: match found with the PnP device '00:08' and the driver 'serial'
00:08: ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A
RAMDISK driver initialized: 16 RAM disks of 65536K size 1024 blocksize
pnp: the driver 'i8042 kbd' has been registered
pnp: the driver 'i8042 aux' has been registered
pnp: the driver 'i8042 kbd' has been unregistered
pnp: the driver 'i8042 aux' has been unregistered
PNP: No PS/2 controller found. Probing ports directly.
serio: i8042 AUX port at 0x60,0x64 irq 12
serio: i8042 KBD port at 0x60,0x64 irq 1
mice: PS/2 mouse device common for all mice
TCP bic registered
NET: Registered protocol family 1
NET: Registered protocol family 17
NET: Registered protocol family 8
NET: Registered protocol family 20
ACPI: (supports S0 S1 S3 S4 S5)
Freeing unused kernel memory: 176k freed
ACPI: Fan [FAN] (on)
ACPI: Thermal Zone [THRM] (40 C)
ohci_hcd: 2005 April 22 USB 1.1 'Open' Host Controller (OHCI) Driver (PCI)
ACPI: PCI Interrupt Link [APCF] enabled at IRQ 23
GSI 17 sharing vector 0x32 and IRQ 17
ACPI: PCI Interrupt 0000:00:0a.0[A] -> Link [APCF] -> GSI 23 (level, low) -> IRQ 50
PCI: Setting latency timer of device 0000:00:0a.0 to 64
ohci_hcd 0000:00:0a.0: OHCI Host Controller
ohci_hcd 0000:00:0a.0: new USB bus registered, assigned bus number 1
ohci_hcd 0000:00:0a.0: irq 50, io mem 0xfe02f000
Uniform Multi-Platform E-IDE driver Revision: 7.00alpha2
ide: Assuming 33MHz system bus speed for PIO modes; override with idebus=xx
usb usb1: configuration #1 chosen from 1 choice
hub 1-0:1.0: USB hub found
hub 1-0:1.0: 10 ports detected
Floppy drive(s): fd0 is 1.44M
ieee1394: Initialized config rom entry `ip1394'
forcedeth.c: Reverse Engineered nForce ethernet driver. Version 0.56.
SCSI subsystem initialized
FDC 0 is a post-1991 82077
ACPI: PCI Interrupt Link [APCL] enabled at IRQ 22
GSI 18 sharing vector 0x3A and IRQ 18
ACPI: PCI Interrupt 0000:00:0a.1[B] -> Link [APCL] -> GSI 22 (level, low) -> IRQ 58
PCI: Setting latency timer of device 0000:00:0a.1 to 64
ehci_hcd 0000:00:0a.1: EHCI Host Controller
ehci_hcd 0000:00:0a.1: new USB bus registered, assigned bus number 2
ehci_hcd 0000:00:0a.1: debug port 1
PCI: cache line size of 64 is not supported by device 0000:00:0a.1
ehci_hcd 0000:00:0a.1: irq 58, io mem 0xfe02e000
ehci_hcd 0000:00:0a.1: USB 2.0 started, EHCI 1.00, driver 10 Dec 2004
usb usb2: configuration #1 chosen from 1 choice
hub 2-0:1.0: USB hub found
hub 2-0:1.0: 10 ports detected
libata version 2.00 loaded.
ACPI: PCI Interrupt Link [APC5] enabled at IRQ 16
ACPI: PCI Interrupt 0000:04:02.0[A] -> Link [APC5] -> GSI 16 (level, low) -> IRQ 177
NFORCE-MCP55: IDE controller at PCI slot 0000:00:0c.0
NFORCE-MCP55: chipset revision 161
NFORCE-MCP55: not 100% native mode: will probe irqs later
NFORCE-MCP55: 0000:00:0c.0 (rev a1) UDMA133 controller
ide0: BM-DMA at 0xf000-0xf007, BIOS settings: hda:DMA, hdb:DMA
Probing IDE interface ide0...
usb 1-3: new low speed USB device using ohci_hcd and address 2
hdb: TEAC DV-W516GA, ATAPI CD/DVD-ROM drive
usb 1-3: configuration #1 chosen from 1 choice
ide0 at 0x1f0-0x1f7,0x3f6 on irq 14
usb 1-4: new low speed USB device using ohci_hcd and address 3
usb 1-4: configuration #1 chosen from 1 choice
usbcore: registered new driver hiddev
ACPI: PCI Interrupt Link [APCH] enabled at IRQ 21
GSI 19 sharing vector 0x42 and IRQ 19
ACPI: PCI Interrupt 0000:00:10.0[A] -> Link [APCH] -> GSI 21 (level, low) -> IRQ 66
PCI: Setting latency timer of device 0000:00:10.0 to 64
forcedeth: using HIGHDMA
input: Logitech USB-PS/2 Optical Mouse as /class/input/input0
input: USB HID v1.10 Mouse [Logitech USB-PS/2 Optical Mouse] on usb-0000:00:0a.0-3
input: Logitech Logitech USB Keyboard as /class/input/input1
input: USB HID v1.10 Keyboard [Logitech Logitech USB Keyboard] on usb-0000:00:0a.0-4
input: Logitech Logitech USB Keyboard as /class/input/input2
input: USB HID v1.10 Mouse [Logitech Logitech USB Keyboard] on usb-0000:00:0a.0-4
usbcore: registered new driver usbhid
drivers/usb/input/hid-core.c: v2.6:USB HID core driver
eth0: forcedeth.c: subsystem: 01043:81fb bound to 0000:00:10.0
ACPI: PCI Interrupt Link [AMC1] enabled at IRQ 20
GSI 20 sharing vector 0x4A and IRQ 20
ACPI: PCI Interrupt 0000:00:11.0[A] -> Link [AMC1] -> GSI 20 (level, low) -> IRQ 74
PCI: Setting latency timer of device 0000:00:11.0 to 64
forcedeth: using HIGHDMA
eth1: forcedeth.c: subsystem: 01043:81fb bound to 0000:00:11.0
scsi0 : Adaptec AIC7XXX EISA/VLB/PCI SCSI HBA DRIVER, Rev 7.0
<Adaptec 3960D Ultra160 SCSI adapter>
aic7899: Ultra160 Wide Channel A, SCSI Id=7, 32/253 SCBs
ACPI: PCI Interrupt Link [APC6] enabled at IRQ 16
ACPI: PCI Interrupt 0000:04:02.1[B] -> Link [APC6] -> GSI 16 (level, low) -> IRQ 177
scsi1 : Adaptec AIC7XXX EISA/VLB/PCI SCSI HBA DRIVER, Rev 7.0
<Adaptec 3960D Ultra160 SCSI adapter>
aic7899: Ultra160 Wide Channel B, SCSI Id=7, 32/253 SCBs
Vendor: IBM Model: IC35L036UWD210-0 Rev: S5BS
Type: Direct-Access ANSI SCSI revision: 03
scsi1:A:0:0: Tagged Queuing enabled. Depth 8
target1:0:0: Beginning Domain Validation
target1:0:0: wide asynchronous
target1:0:0: FAST-80 WIDE SCSI 160.0 MB/s DT (12.5 ns, offset 63)
target1:0:0: Ending Domain Validation
Vendor: IBM Model: IC35L036UWD210-0 Rev: S5BS
Type: Direct-Access ANSI SCSI revision: 03
scsi1:A:1:0: Tagged Queuing enabled. Depth 8
target1:0:1: Beginning Domain Validation
target1:0:1: wide asynchronous
target1:0:1: FAST-80 WIDE SCSI 160.0 MB/s DT (12.5 ns, offset 63)
target1:0:1: Ending Domain Validation
ACPI: PCI Interrupt Link [APC4] enabled at IRQ 19
GSI 21 sharing vector 0x52 and IRQ 21
ACPI: PCI Interrupt 0000:02:0b.0[A] -> Link [APC4] -> GSI 19 (level, low) -> IRQ 82
udev: renamed network interface eth1 to eth2
ohci1394: fw-host0: OHCI-1394 1.1 (PCI): IRQ=[82] MMIO=[fdfff000-fdfff7ff] Max Packet=[2048] IR/IT contexts=[4/8]
sata_nv 0000:00:0d.0: version 2.0
ACPI: PCI Interrupt Link [APSI] enabled at IRQ 23
ACPI: PCI Interrupt 0000:00:0d.0[A] -> Link [APSI] -> GSI 23 (level, low) -> IRQ 50
PCI: Setting latency timer of device 0000:00:0d.0 to 64
SCSI device sda: 71687340 512-byte hdwr sectors (36704 MB)
ata1: SATA max UDMA/133 cmd 0x9F0 ctl 0xBF2 bmdma 0xDC00 irq 50
ata2: SATA max UDMA/133 cmd 0x970 ctl 0xB72 bmdma 0xDC08 irq 50
scsi2 : sata_nv
sda: Write Protect is off
sda: Mode Sense: cb 00 00 08
udev: renamed network interface eth0 to eth1
SCSI device sda: drive cache: write back
SCSI device sda: 71687340 512-byte hdwr sectors (36704 MB)
sda: Write Protect is off
sda: Mode Sense: cb 00 00 08
SCSI device sda: drive cache: write back
sda: sda1 sda2 sda3 sda4 < sda5 sda6 sda7 sda8 >
sd 1:0:0:0: Attached scsi disk sda
SCSI device sdb: 71687340 512-byte hdwr sectors (36704 MB)
sdb: Write Protect is off
sdb: Mode Sense: cb 00 00 08
SCSI device sdb: drive cache: write back
SCSI device sdb: 71687340 512-byte hdwr sectors (36704 MB)
sdb: Write Protect is off
sdb: Mode Sense: cb 00 00 08
SCSI device sdb: drive cache: write back
sdb: sdb1 sdb2 sdb3 sdb4 < sdb5 sdb6 sdb7 sdb8 >
sd 1:0:1:0: Attached scsi disk sdb
ata1: SATA link down (SStatus 0 SControl 300)
ATA: abnormal status 0x7F on port 0x9F7
scsi3 : sata_nv
ata2: SATA link up 3.0 Gbps (SStatus 123 SControl 300)
ata2.00: ATA-7, max UDMA/133, 781422768 sectors: LBA48 NCQ (depth 0/32)
ata2.00: ata2: dev 0 multi count 1
ata2.00: configured for UDMA/133
Vendor: ATA Model: ST3400620AS Rev: 3.AA
Type: Direct-Access ANSI SCSI revision: 05
SCSI device sdc: 781422768 512-byte hdwr sectors (400088 MB)
sdc: Write Protect is off
sdc: Mode Sense: 00 3a 00 00
SCSI device sdc: drive cache: write back
SCSI device sdc: 781422768 512-byte hdwr sectors (400088 MB)
sdc: Write Protect is off
sdc: Mode Sense: 00 3a 00 00
SCSI device sdc: drive cache: write back
sdc: sdc1
sd 3:0:0:0: Attached scsi disk sdc
ACPI: PCI Interrupt Link [APSJ] enabled at IRQ 22
ACPI: PCI Interrupt 0000:00:0d.1[B] -> Link [APSJ] -> GSI 22 (level, low) -> IRQ 58
PCI: Setting latency timer of device 0000:00:0d.1 to 64
ata3: SATA max UDMA/133 cmd 0x9E0 ctl 0xBE2 bmdma 0xC800 irq 58
ata4: SATA max UDMA/133 cmd 0x960 ctl 0xB62 bmdma 0xC808 irq 58
scsi4 : sata_nv
ieee1394: Host added: ID:BUS[0-00:1023] GUID[0011d80000e57e94]
ata3: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
ata3.00: ATA-6, max UDMA/133, 234425264 sectors: LBA48
ata3.00: ata3: dev 0 multi count 1
ata3.00: configured for UDMA/133
scsi5 : sata_nv
ata4: SATA link up 3.0 Gbps (SStatus 123 SControl 300)
ata4.00: ATA-7, max UDMA/133, 390721968 sectors: LBA48 NCQ (depth 0/32)
ata4.00: ata4: dev 0 multi count 1
ata4.00: configured for UDMA/133
Vendor: ATA Model: ST3120026AS Rev: 3.05
Type: Direct-Access ANSI SCSI revision: 05
SCSI device sdd: 234425264 512-byte hdwr sectors (120026 MB)
sdd: Write Protect is off
sdd: Mode Sense: 00 3a 00 00
SCSI device sdd: drive cache: write back
SCSI device sdd: 234425264 512-byte hdwr sectors (120026 MB)
sdd: Write Protect is off
sdd: Mode Sense: 00 3a 00 00
SCSI device sdd: drive cache: write back
sdd: sdd1 < sdd5 >
sd 4:0:0:0: Attached scsi disk sdd
Vendor: ATA Model: ST3200820AS Rev: 3.AA
Type: Direct-Access ANSI SCSI revision: 05
SCSI device sde: 390721968 512-byte hdwr sectors (200050 MB)
sde: Write Protect is off
sde: Mode Sense: 00 3a 00 00
SCSI device sde: drive cache: write back
SCSI device sde: 390721968 512-byte hdwr sectors (200050 MB)
sde: Write Protect is off
sde: Mode Sense: 00 3a 00 00
SCSI device sde: drive cache: write back
sde: sde1 < sde5 >
sd 5:0:0:0: Attached scsi disk sde
ACPI: PCI Interrupt Link [ASA2] enabled at IRQ 21
ACPI: PCI Interrupt 0000:00:0d.2[C] -> Link [ASA2] -> GSI 21 (level, low) -> IRQ 66
PCI: Setting latency timer of device 0000:00:0d.2 to 64
ata5: SATA max UDMA/133 cmd 0xC400 ctl 0xC002 bmdma 0xB400 irq 66
ata6: SATA max UDMA/133 cmd 0xBC00 ctl 0xB802 bmdma 0xB408 irq 66
scsi6 : sata_nv
ata5: SATA link up 3.0 Gbps (SStatus 123 SControl 300)
ata5.00: ATA-7, max UDMA/133, 312581808 sectors: LBA48 NCQ (depth 0/32)
ata5.00: ata5: dev 0 multi count 1
ata5.00: configured for UDMA/133
scsi7 : sata_nv
ata6: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
ata6.00: ATA-6, max UDMA/133, 312581808 sectors: LBA48 NCQ (depth 0/32)
ata6.00: ata6: dev 0 multi count 1
ata6.00: configured for UDMA/133
Vendor: ATA Model: ST3160812AS Rev: 3.AA
Type: Direct-Access ANSI SCSI revision: 05
SCSI device sdf: 312581808 512-byte hdwr sectors (160042 MB)
sdf: Write Protect is off
sdf: Mode Sense: 00 3a 00 00
SCSI device sdf: drive cache: write back
SCSI device sdf: 312581808 512-byte hdwr sectors (160042 MB)
sdf: Write Protect is off
sdf: Mode Sense: 00 3a 00 00
SCSI device sdf: drive cache: write back
sdf: sdf1
sd 6:0:0:0: Attached scsi disk sdf
Vendor: ATA Model: ST3160827AS Rev: 3.42
Type: Direct-Access ANSI SCSI revision: 05
SCSI device sdg: 312581808 512-byte hdwr sectors (160042 MB)
sdg: Write Protect is off
sdg: Mode Sense: 00 3a 00 00
SCSI device sdg: drive cache: write back
SCSI device sdg: 312581808 512-byte hdwr sectors (160042 MB)
sdg: Write Protect is off
sdg: Mode Sense: 00 3a 00 00
SCSI device sdg: drive cache: write back
sdg: sdg1
sd 7:0:0:0: Attached scsi disk sdg
hdb: ATAPI 48X DVD-ROM DVD-R CD-R/RW drive, 2048kB Cache, UDMA(33)
Uniform CD-ROM driver Revision: 3.20
Probing IDE interface ide1...
md: md driver 0.90.3 MAX_MD_DEVS=256, MD_SB_DISKS=27
md: bitmap version 4.39
md: raid1 personality registered for level 1
md: md0 stopped.
md: md1 stopped.
md: md2 stopped.
md: md3 stopped.
md: md4 stopped.
md: md5 stopped.
md: bind<sdb8>
md: bind<sda8>
md: kicking non-fresh sdb8 from array!
md: unbind<sdb8>
md: export_rdev(sdb8)
raid1: raid set md5 active with 1 out of 2 mirrors
md: bind<sdb7>
md: bind<sda7>
raid1: raid set md4 active with 2 out of 2 mirrors
md: bind<sdb6>
md: bind<sda6>
raid1: raid set md3 active with 2 out of 2 mirrors
md: bind<sdb5>
md: bind<sda5>
raid1: raid set md2 active with 2 out of 2 mirrors
md: bind<sdb2>
md: bind<sda2>
raid1: raid set md1 active with 2 out of 2 mirrors
md: bind<sdb1>
md: bind<sda1>
raid1: raid set md0 active with 2 out of 2 mirrors
kjournald starting. Commit interval 5 seconds
EXT3-fs: mounted filesystem with ordered data mode.
ts: Compaq touchscreen protocol output
eth1394: eth0: IEEE-1394 IPv4 over 1394 Ethernet (fw-host0)
i2c_adapter i2c-0: nForce2 SMBus adapter at 0x1c00
i2c_adapter i2c-1: nForce2 SMBus adapter at 0x1c40
pci_hotplug: PCI Hot Plug PCI Core version: 0.5
shpchp: HPC vendor_id 1033 device_id 125 ss_vid 0 ss_did 0
shpchp: Standard Hot Plug PCI Controller Driver version: 0.4
input: PC Speaker as /class/input/input3
pnp: the driver 'parport_pc' has been registered
pnp: match found with the PnP device '00:09' and the driver 'parport_pc'
parport: PnPBIOS parport detected.
parport0: PC-style at 0x378 (0x778), irq 7, dma 3 [PCSPP,TRISTATE,COMPAT,ECP,DMA]
ACPI: PCI Interrupt Link [AAZA] enabled at IRQ 20
ACPI: PCI Interrupt 0000:00:0e.1[B] -> Link [AAZA] -> GSI 20 (level, low) -> IRQ 74
PCI: Setting latency timer of device 0000:00:0e.1 to 64
hda_codec: Unknown model for AD1988, trying auto-probe from BIOS...
EXT3 FS on md1, internal journal
loop: loaded (max 8 devices)
ieee1394: sbp2: Driver forced to serialize I/O (serialize_io=1)
ieee1394: sbp2: Try serialize_io=0 for better performance
device-mapper: ioctl: 4.7.0-ioctl (2006-06-24) initialised: dm-devel@redhat.com
fuse init (API version 7.7)
kjournald starting. Commit interval 5 seconds
EXT3 FS on sdc1, internal journal
EXT3-fs: mounted filesystem with ordered data mode.
kjournald starting. Commit interval 5 seconds
EXT3 FS on md0, internal journal
EXT3-fs: mounted filesystem with ordered data mode.
kjournald starting. Commit interval 5 seconds
EXT3 FS on md5, internal journal
EXT3-fs: mounted filesystem with ordered data mode.
kjournald starting. Commit interval 5 seconds
EXT3 FS on md4, internal journal
EXT3-fs: mounted filesystem with ordered data mode.
kjournald starting. Commit interval 5 seconds
EXT3 FS on md2, internal journal
EXT3-fs: mounted filesystem with ordered data mode.
kjournald starting. Commit interval 5 seconds
EXT3 FS on md3, internal journal
EXT3-fs: mounted filesystem with ordered data mode.
NTFS driver 2.1.27 [Flags: R/W MODULE].
NTFS volume version 3.1.
NTFS-fs error (device sdf1): load_system_files(): Volume is dirty. Mounting read-only. Run chkdsk and mount in Windows.
NTFS volume version 3.1.
NTFS-fs error (device sdd5): load_system_files(): Volume is dirty. Mounting read-only. Run chkdsk and mount in Windows.
NTFS volume version 3.1.
NTFS-fs error (device sde5): load_system_files(): Volume is dirty. Mounting read-only. Run chkdsk and mount in Windows.
NTFS volume version 3.1.
NTFS-fs error (device sdg1): load_system_files(): Volume is dirty. Mounting read-only. Run chkdsk and mount in Windows.
NET: Registered protocol family 10
lo: Disabled Privacy Extensions
IPv6 over IPv4 tunneling driver
ACPI: Power Button (FF) [PWRF]
ACPI: Power Button (CM) [PWRB]
eth1: no IPv6 routers present
