Проблемы с внутренним модемом Zyxel

[Mansai]

В OpenSuSe 10.3 внутренний модем Zyxel(точно модель не помню) не определился автоматически, но отображается как PCI устройство. Я нашёл, где происходит настройка PCI устройств, но не знаю, что там нужно вводить. Там надо выбрать, что за плата(из списка PCI устройств) и ввести драйвер и sysFS каталог. Так вот, что в нужно вводить в поля "Драйвер" и "sysFS каталог"?

[BIgAndy]

но отображается как PCI устройство. Я нашёл, где происходит настройка PCI устройств, но не знаю, что там нужно вводить. Там надо выбрать, что за плата(из списка PCI устройств) и ввести драйвер и sysFS каталог. Так вот, что в нужно вводить в поля "Драйвер" и "sysFS каталог"?

А нахрена вам это все, если так все у вас определилось? Что-нибудь не работает? /dev/ttyX создаются?
Работайте себе спокойно.
Многие о таком счастье и мечатть не могли со своими софт-модемами...

[Mansai]

Разделы то создаются только они зовутся /dev/ttySX это первое.
Второе, когда я определяю модем (указывая устройство /dev/ttyS0) при подключении в журнале пишется, что модемка не отвечает.
А показывается, что оно PCI устройство только при проверке установленного оборудование(когда список его создаётся) и нигде более не отображается.

[BIgAndy]

Разделы то создаются только они зовутся /dev/ttySX это первое.

Это хорошо.

Второе, когда я определяю модем (указывая устройство /dev/ttyS0) при подключении в журнале пишется, что модемка не отвечает.

Как вы его определяете? Какой командой? Какой вывод? Вы уверены, что модем на dev/ttyS0, а не на, скажем /dev/ttys3? dmesg смотрели?

А показывается, что оно PCI устройство только при проверке установленного оборудование(когда список его создаётся) и нигде более не отображается.

А где еще должен отображаться?
В lspci и lshal отображается?

[Mansai]

Проверил все /dev/ttySX, при всех одно и тоже (хотя я склоняюсь к тому, что верное устройство /dev/ttyS2 так как /dev/modem(его тоже пробовал) ссылка именно на него.)! Пишет, что посылается строка инициализации модема, а потом, что модем не отвечает. А определяю я модем через Yast.
И что такое dmesg?

[BIgAndy]

Проверил все /dev/ttySX, при всех одно и тоже (хотя я склоняюсь к тому, что верное устройство /dev/ttyS2 так как /dev/modem(его тоже пробовал) ссылка именно на него.)! Пишет, что посылается строка инициализации модема, а потом, что модем не отвечает. А определяю я модем через Yast.
И что такое dmesg?

dmesg - сообщения ядра. Там посмотрите куда примонтировался модем.
Дальше настраиваете minicom и пробуете посылать команды на модем. И смотрите его отклик. Из дополнительной информации : man minicom и документацию по at-командам вашего модема.

[Mansai]

То ли меня глючит, то ли у меня не из того места глаза, но в тексте, выданном после команды dmesg про модем не было ничего:

Код:

daniil@linux-v1nr:~> dmesg Linux version 2.6.22.5-31-default (geeko@buildhost) (gcc version 4.2.1 (SUSE Linux)) #1 SMP 2007/09/21 22:29:00 UTC BIOS-provided physical RAM map: BIOS-e820: 0000000000000000 - 000000000009f800 (usable) BIOS-e820: 000000000009f800 - 00000000000a0000 (reserved) BIOS-e820: 00000000000f0000 - 0000000000100000 (reserved) BIOS-e820: 0000000000100000 - 000000001fff0000 (usable) BIOS-e820: 000000001fff0000 - 000000001fff3000 (ACPI NVS) BIOS-e820: 000000001fff3000 - 0000000020000000 (ACPI data) BIOS-e820: 00000000fec00000 - 0000000100000000 (reserved) 0MB HIGHMEM available. 511MB LOWMEM available. found SMP MP-table at 000f5350 Entering add_active_range(0, 0, 131056) 0 entries of 256 used Zone PFN ranges: DMA 0 -> 4096 Normal 4096 -> 131056 HighMem 131056 -> 131056 early_node_map[1] active PFN ranges 0: 0 -> 131056 On node 0 totalpages: 131056 DMA zone: 32 pages used for memmap DMA zone: 0 pages reserved DMA zone: 4064 pages, LIFO batch:0 Normal zone: 991 pages used for memmap Normal zone: 125969 pages, LIFO batch:31 HighMem zone: 0 pages used for memmap DMI 2.2 present. Using APIC driver default ACPI: RSDP 000F7100, 0014 (r0 IntelR) ACPI: RSDT 1FFF3000, 002C (r1 IntelR AWRDACPI 42302E31 AWRD 0) ACPI: FACP 1FFF3040, 0074 (r1 IntelR AWRDACPI 42302E31 AWRD 0) ACPI: DSDT 1FFF30C0, 405F (r1 INTELR AWRDACPI 1000 MSFT 100000E) ACPI: FACS 1FFF0000, 0040 ACPI: APIC 1FFF7140, 007C (r1 IntelR AWRDACPI 42302E31 AWRD 0) ACPI: PM-Timer IO Port: 0x408 ACPI: Local APIC address 0xfee00000 ACPI: LAPIC (acpi_id[0x00] lapic_id[0x00] enabled) Processor #0 15:2 APIC version 20 ACPI: LAPIC (acpi_id[0x01] lapic_id[0x01] enabled) Processor #1 15:2 APIC version 20 ACPI: LAPIC_NMI (acpi_id[0x00] high edge lint[0x1]) ACPI: LAPIC_NMI (acpi_id[0x01] high edge lint[0x1]) ACPI: IOAPIC (id[0x02] address[0xfec00000] gsi_base[0]) IOAPIC[0]: apic_id 2, version 32, address 0xfec00000, GSI 0-23 ACPI: INT_SRC_OVR (bus 0 bus_irq 0 global_irq 2 dfl dfl) ACPI: INT_SRC_OVR (bus 0 bus_irq 9 global_irq 9 high level) ACPI: INT_SRC_OVR (bus 0 bus_irq 14 global_irq 14 high edge) ACPI: INT_SRC_OVR (bus 0 bus_irq 15 global_irq 15 high edge) ACPI: IRQ0 used by override. ACPI: IRQ2 used by override. ACPI: IRQ9 used by override. ACPI: IRQ14 used by override. ACPI: IRQ15 used by override. Enabling APIC mode: Flat. Using 1 I/O APICs Using ACPI (MADT) for SMP configuration information Allocating PCI resources starting at 30000000 (gap: 20000000:dec00000) Built 1 zonelists. Total pages: 130033 Kernel command line: auto BOOT_IMAGE=oS_10.3 ro root=/dev/disk/by-id/scsi-SATA_WDC_WD800JB-00FWD-WCAJ91901000-part2 resu me=/dev/sda3 splash=silent showopts bootsplash: silent mode. mapped APIC to ffffd000 (fee00000) mapped IOAPIC to ffffc000 (fec00000) Enabling fast FPU save and restore... done. Enabling unmasked SIMD FPU exception support... done. Initializing CPU#0 PID hash table entries: 2048 (order: 11, 8192 bytes) Detected 2793.219 MHz processor. Console: colour dummy device 80x25 Dentry cache hash table entries: 65536 (order: 6, 262144 bytes) Inode-cache hash table entries: 32768 (order: 5, 131072 bytes) Memory: 511768k/524224k available (1825k kernel code, 11984k reserved, 764k data, 228k init, 0k highmem) virtual kernel memory layout: fixmap : 0xffdf4000 - 0xfffff000 (2092 kB) pkmap : 0xff800000 - 0xffc00000 (4096 kB) vmalloc : 0xe0800000 - 0xff7fe000 ( 495 MB) lowmem : 0xc0000000 - 0xdfff0000 ( 511 MB) .init : 0xc038e000 - 0xc03c7000 ( 228 kB) .data : 0xc02c86ed - 0xc0387964 ( 764 kB) .text : 0xc0100000 - 0xc02c86ed (1825 kB) Checking if this processor honours the WP bit even in supervisor mode... Ok. Calibrating delay using timer specific routine.. 5590.46 BogoMIPS (lpj=11180926) Security Framework v1.0.0 initialized Mount-cache hash table entries: 512 CPU: After generic identify, caps: bfebfbff 00000000 00000000 00000000 00004400 00000000 00000000 CPU: Trace cache: 12K uops, L1 D cache: 8K CPU: L2 cache: 512K CPU: Physical Processor ID: 0 CPU: After all inits, caps: bfebfbff 00000000 00000000 0000b080 00004400 00000000 00000000 Intel machine check architecture supported. Intel machine check reporting enabled on CPU#0. CPU0: Intel P4/Xeon Extended MCE MSRs (12) available CPU0: Thermal monitoring enabled Compat vDSO mapped to ffffe000. Checking 'hlt' instruction... OK. SMP alternatives: switching to UP code Unpacking initramfs... done Freeing initrd memory: 4044k freed ACPI: Core revision 20070126 Parsing all Control Methods: Table [DSDT](id 0001) - 580 Objects with 53 Devices 152 Methods 33 Regions tbxface-0587 [00] tb_load_namespace : ACPI Tables successfully acquired evxfevnt-0091 [00] enable : Transition to ACPI mode successful CPU0: Intel® Pentium® 4 CPU 2.80GHz stepping 09 SMP alternatives: switching to SMP code Booting processor 1/1 eip 3000 Initializing CPU#1 Calibrating delay using timer specific routine.. 5586.43 BogoMIPS (lpj=11172875) CPU: After generic identify, caps: bfebfbff 00000000 00000000 00000000 00004400 00000000 00000000 CPU: Trace cache: 12K uops, L1 D cache: 8K CPU: L2 cache: 512K CPU: Physical Processor ID: 0 CPU: After all inits, caps: bfebfbff 00000000 00000000 0000b080 00004400 00000000 00000000 Intel machine check architecture supported. Intel machine check reporting enabled on CPU#1. CPU1: Intel P4/Xeon Extended MCE MSRs (12) available CPU1: Thermal monitoring enabled CPU1: Intel® Pentium® 4 CPU 2.80GHz stepping 09 Total of 2 processors activated (11176.90 BogoMIPS). ENABLING IO-APIC IRQs ..TIMER: vector=0x31 apic1=0 pin1=2 apic2=-1 pin2=-1 checking TSC synchronization [CPU#0 -> CPU#1]: passed. Brought up 2 CPUs migration_cost=16 Booting paravirtualized kernel on bare hardware NET: Registered protocol family 16 ACPI: bus type pci registered PCI: PCI BIOS revision 2.10 entry at 0xfb450, last bus=2 PCI: Using configuration type 1 Setting up standard PCI resources evgpeblk-0956 [00] ev_create_gpe_block : GPE 00 to 1F [_GPE] 4 regs on int 0x9 evgpeblk-1052 [00] ev_initialize_gpe_bloc: Found 9 Wake, Enabled 1 Runtime GPEs in this block Completing Region/Field/Buffer/Package initialization:................................................................. . ...... Initialized 33/33 Regions 9/9 Fields 19/19 Buffers 11/17 Packages (589 nodes) Initializing Device/Processor/Thermal objects by executing _INI methods:.. Executed 2 _INI methods requiring 1 _STA executions (examined 58 objects) ACPI: Interpreter enabled ACPI: (supports S0 S1 S4 S5) ACPI: Using IOAPIC for interrupt routing ACPI: PCI Root Bridge [PCI0] (0000:00) PCI: Probing PCI hardware (bus 00) PCI quirk: region 0400-047f claimed by ICH4 ACPI/GPIO/TCO PCI quirk: region 0480-04bf claimed by ICH4 GPIO PCI: Transparent bridge - 0000:00:1e.0 ACPI: PCI Interrupt Routing Table [\_SB_.PCI0._PRT] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.HUB0._PRT] ACPI: PCI Interrupt Link [LNKA] (IRQs 3 4 5 7 9 10 *11 12 14 15) ACPI: PCI Interrupt Link [LNKB] (IRQs 3 4 5 7 9 *10 11 12 14 15) ACPI: PCI Interrupt Link [LNKC] (IRQs 3 4 5 7 *9 10 11 12 14 15) ACPI: PCI Interrupt Link [LNKD] (IRQs 3 4 *5 7 9 10 11 12 14 15) ACPI: PCI Interrupt Link [LNKE] (IRQs *3 4 5 7 9 10 11 12 14 15) ACPI: PCI Interrupt Link [LNKF] (IRQs 3 4 5 7 9 10 11 12 14 15) *0, disabled. ACPI: PCI Interrupt Link [LNK0] (IRQs 3 4 5 7 9 10 11 12 14 15) *0, disabled. ACPI: PCI Interrupt Link [LNK1] (IRQs 3 4 *5 7 9 10 11 12 14 15) Linux Plug and Play Support v0.97 © Adam Belay pnp: PnP ACPI init ACPI: bus type pnp registered pnp: PnP ACPI: found 13 devices ACPI: ACPI bus type pnp unregistered PnPBIOS: Disabled by ACPI PNP PCI: Using ACPI for IRQ routing PCI: If a device doesn't work, try "pci=routeirq". If it helps, post a report ACPI: RTC can wake from S4 pnp: 00:0b: ioport range 0x400-0x4bf could not be reserved pnp: 00:0c: iomem range 0xcd000-0xcffff has been reserved pnp: 00:0c: iomem range 0xf0000-0xf7fff could not be reserved pnp: 00:0c: iomem range 0xf8000-0xfbfff could not be reserved pnp: 00:0c: iomem range 0xfc000-0xfffff could not be reserved Time: tsc clocksource has been installed. PCI: Bridge: 0000:00:01.0 IO window: a000-afff MEM window: f8000000-f9ffffff PREFETCH window: d0000000-efffffff PCI: Bridge: 0000:00:1e.0 IO window: b000-bfff MEM window: fa000000-fa0fffff PREFETCH window: disabled. PCI: Setting latency timer of device 0000:00:1e.0 to 64 NET: Registered protocol family 2 IP route cache hash table entries: 4096 (order: 2, 16384 bytes) TCP established hash table entries: 16384 (order: 5, 196608 bytes) TCP bind hash table entries: 16384 (order: 5, 131072 bytes) TCP: Hash tables configured (established 16384 bind 16384) TCP reno registered Machine check exception polling timer started. audit: initializing netlink socket (disabled) audit(1223709684.488:1): initialized Total HugeTLB memory allocated, 0 VFS: Disk quotas dquot_6.5.1 Dquot-cache hash table entries: 1024 (order 0, 4096 bytes) io scheduler noop registered io scheduler anticipatory registered io scheduler deadline registered io scheduler cfq registered (default) Boot video device is 0000:01:00.0 vesafb: framebuffer at 0xd0000000, mapped to 0xe0880000, using 10240k, total 131072k vesafb: mode is 1280x1024x16, linelength=2560, pages=50 vesafb: protected mode interface info at c000:5781 vesafb: pmi: set display start = c00c5815, set palette = c00c5861 vesafb: pmi: ports = a010 a016 a054 a038 a03c a05c a000 a004 a0b0 a0b2 a0b4 vesafb: scrolling: redraw vesafb: Truecolor: size=0:5:6:5, shift=0:11:5:0 bootsplash 3.1.6-2004/03/31: looking for picture... bootsplash: silentjpeg size 98233 bytes bootsplash: ...found (1280x1024, 35219 bytes, v3). Console: switching to colour frame buffer device 156x60 fb0: VESA VGA frame buffer device isapnp: Scanning for PnP cards... Switched to NOHz mode on CPU #0 Switched to NOHz mode on CPU #1 isapnp: No Plug & Play device found Real Time Clock Driver v1.12ac Serial: 8250/16550 driver $Revision: 1.90 $ 4 ports, IRQ sharing enabled serial8250: ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A 00:07: ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A Floppy drive(s): fd0 is 1.44M FDC 0 is a post-1991 82077 PNP: PS/2 Controller [PNP0303:PS2K,PNP0f13:PS2M] at 0x60,0x64 irq 1,12 serio: i8042 KBD port at 0x60,0x64 irq 1 serio: i8042 AUX port at 0x60,0x64 irq 12 mice: PS/2 mouse device common for all mice input: AT Translated Set 2 keyboard as /class/input/input0 input: PC Speaker as /class/input/input1 input: ImExPS/2 Generic Explorer Mouse as /class/input/input2 NET: Registered protocol family 1 Using IPI No-Shortcut mode Freeing unused kernel memory: 228k freed ACPI: Thermal Zone [THRM] (43 C) SCSI subsystem initialized libata version 3.00 loaded. ata_piix 0000:00:1f.1: version 2.11 ACPI: PCI Interrupt 0000:00:1f.1[A] -> GSI 18 (level, low) -> IRQ 16 PCI: Setting latency timer of device 0000:00:1f.1 to 64 scsi0 : ata_piix scsi1 : ata_piix ata1: PATA max UDMA/133 cmd 0x000101f0 ctl 0x000103f6 bmdma 0x0001f000 irq 14 ata2: PATA max UDMA/133 cmd 0x00010170 ctl 0x00010376 bmdma 0x0001f008 irq 15 ata1.00: ATA-6: WDC WD800JB-00FMA0, 13.03G13, max UDMA/100 ata1.00: 156301488 sectors, multi 16: LBA ata1.00: configured for UDMA/100 ata2.00: ATAPI: _NEC DVD_RW ND-2500A, 1.06, max UDMA/33 ata2.00: configured for UDMA/33 scsi 0:0:0:0: Direct-Access ATA WDC WD800JB-00FM 13.0 PQ: 0 ANSI: 5 scsi 1:0:0:0: CD-ROM _NEC DVD_RW ND-2500A 1.06 PQ: 0 ANSI: 5 ACPI: Fan [FAN] (on) BIOS EDD facility v0.16 2004-Jun-25, 1 devices found usbcore: registered new interface driver usbfs usbcore: registered new interface driver hub usbcore: registered new device driver usb ACPI: PCI Interrupt 0000:00:1d.7[D] -> GSI 23 (level, low) -> IRQ 17 PCI: Setting latency timer of device 0000:00:1d.7 to 64 USB Universal Host Controller Interface driver v3.0 ehci_hcd 0000:00:1d.7: EHCI Host Controller ehci_hcd 0000:00:1d.7: new USB bus registered, assigned bus number 1 PCI: cache line size of 128 is not supported by device 0000:00:1d.7 ehci_hcd 0000:00:1d.7: irq 17, io mem 0xfa100000 ehci_hcd 0000:00:1d.7: USB 2.0 started, EHCI 1.00, driver 10 Dec 2004 usb usb1: new device found, idVendor=0000, idProduct=0000 usb usb1: new device strings: Mfr=3, Product=2, SerialNumber=1 usb usb1: Product: EHCI Host Controller usb usb1: Manufacturer: Linux 2.6.22.5-31-default ehci_hcd usb usb1: SerialNumber: 0000:00:1d.7 usb usb1: configuration #1 chosen from 1 choice hub 1-0:1.0: USB hub found hub 1-0:1.0: 8 ports detected sd 0:0:0:0: [sda] 156301488 512-byte hardware sectors (80026 MB) sd 0:0:0:0: [sda] Write Protect is off sd 0:0:0:0: [sda] Mode Sense: 00 3a 00 00 sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA sd 0:0:0:0: [sda] 156301488 512-byte hardware sectors (80026 MB) sd 0:0:0:0: [sda] Write Protect is off sd 0:0:0:0: [sda] Mode Sense: 00 3a 00 00 sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA ACPI: PCI Interrupt 0000:00:1d.0[A] -> GSI 16 (level, low) -> IRQ 18 PCI: Setting latency timer of device 0000:00:1d.0 to 64 uhci_hcd 0000:00:1d.0: UHCI Host Controller uhci_hcd 0000:00:1d.0: new USB bus registered, assigned bus number 2 uhci_hcd 0000:00:1d.0: irq 18, io base 0x0000cc00 usb usb2: new device found, idVendor=0000, idProduct=0000 sda:<6>usb usb2: new device strings: Mfr=3, Product=2, SerialNumber=1 sda1 sda2 sda3 usb usb2: Product: UHCI Host Controller usb usb2: Manufacturer: Linux 2.6.22.5-31-default uhci_hcd usb usb2: SerialNumber: 0000:00:1d.0 sd 0:0:0:0: [sda] Attached SCSI disk usb usb2: configuration #1 chosen from 1 choice hub 2-0:1.0: USB hub found hub 2-0:1.0: 2 ports detected ACPI: PCI Interrupt 0000:00:1d.1[B] -> GSI 19 (level, low) -> IRQ 19 PCI: Setting latency timer of device 0000:00:1d.1 to 64 uhci_hcd 0000:00:1d.1: UHCI Host Controller uhci_hcd 0000:00:1d.1: new USB bus registered, assigned bus number 3 uhci_hcd 0000:00:1d.1: irq 19, io base 0x0000c000 usb usb3: new device found, idVendor=0000, idProduct=0000 usb usb3: new device strings: Mfr=3, Product=2, SerialNumber=1 usb usb3: Product: UHCI Host Controller usb usb3: Manufacturer: Linux 2.6.22.5-31-default uhci_hcd usb usb3: SerialNumber: 0000:00:1d.1 usb usb3: configuration #1 chosen from 1 choice hub 3-0:1.0: USB hub found hub 3-0:1.0: 2 ports detected ACPI: PCI Interrupt 0000:00:1d.2[C] -> GSI 18 (level, low) -> IRQ 16 PCI: Setting latency timer of device 0000:00:1d.2 to 64 uhci_hcd 0000:00:1d.2: UHCI Host Controller uhci_hcd 0000:00:1d.2: new USB bus registered, assigned bus number 4 uhci_hcd 0000:00:1d.2: irq 16, io base 0x0000c400 usb usb4: new device found, idVendor=0000, idProduct=0000 usb usb4: new device strings: Mfr=3, Product=2, SerialNumber=1 usb usb4: Product: UHCI Host Controller usb usb4: Manufacturer: Linux 2.6.22.5-31-default uhci_hcd usb usb4: SerialNumber: 0000:00:1d.2 usb usb4: configuration #1 chosen from 1 choice hub 4-0:1.0: USB hub found hub 4-0:1.0: 2 ports detected ACPI: PCI Interrupt 0000:00:1d.3[A] -> GSI 16 (level, low) -> IRQ 18 PCI: Setting latency timer of device 0000:00:1d.3 to 64 uhci_hcd 0000:00:1d.3: UHCI Host Controller uhci_hcd 0000:00:1d.3: new USB bus registered, assigned bus number 5 uhci_hcd 0000:00:1d.3: irq 18, io base 0x0000c800 usb usb5: new device found, idVendor=0000, idProduct=0000 usb usb5: new device strings: Mfr=3, Product=2, SerialNumber=1 usb usb5: Product: UHCI Host Controller usb usb5: Manufacturer: Linux 2.6.22.5-31-default uhci_hcd usb usb5: SerialNumber: 0000:00:1d.3 usb usb5: configuration #1 chosen from 1 choice hub 5-0:1.0: USB hub found hub 5-0:1.0: 2 ports detected swsusp: Basic memory bitmaps created swsusp: Basic memory bitmaps freed Attempting manual resume kjournald starting. Commit interval 5 seconds EXT3-fs: mounted filesystem with ordered data mode. sd 0:0:0:0: Attached scsi generic sg0 type 0 scsi 1:0:0:0: Attached scsi generic sg1 type 5 ACPI: PCI Interrupt 0000:00:1f.3[B] -> GSI 17 (level, low) -> IRQ 20 rtc_cmos 00:03: rtc core: registered rtc_cmos as rtc0 rtc_cmos: probe of 00:03 failed with error -16 pci_hotplug: PCI Hot Plug PCI Core version: 0.5 Linux agpgart interface v0.102 © Dave Jones shpchp: Standard Hot Plug PCI Controller Driver version: 0.4 sr0: scsi3-mmc drive: 40x/40x writer cd/rw xa/form2 cdda tray Uniform CD-ROM driver Revision: 3.20 sr 1:0:0:0: Attached scsi CD-ROM sr0 intel_rng: FWH not detected parport_pc 00:08: reported by Plug and Play ACPI parport0: PC-style at 0x378 (0x778), irq 7, dma 3 [PCSPP,TRISTATE,COMPAT,EPP,ECP,DMA] agpgart: Detected an Intel 865 Chipset. agpgart: AGP aperture is 128M @ 0xf0000000 iTCO_vendor_support: vendor-support=0 iTCO_wdt: Intel TCO WatchDog Timer Driver v1.01 (21-Jan-2007) iTCO_wdt: Found a ICH5 or ICH5R TCO device (Version=1, TCOBASE=0x0460) iTCO_wdt: initialized. heartbeat=30 sec (nowayout=0) input: Power Button (FF) as /class/input/input3 ACPI: Power Button (FF) [PWRF] input: Power Button (CM) as /class/input/input4 ACPI: Power Button (CM) [PWRB] input: Sleep Button (CM) as /class/input/input5 ACPI: Sleep Button (CM) [SLPB] ACPI: PCI Interrupt 0000:00:1f.5[B] -> GSI 17 (level, low) -> IRQ 20 PCI: Setting latency timer of device 0000:00:1f.5 to 64 8139cp: 10/100 PCI Ethernet driver v1.3 (Mar 22, 2004) intel8x0_measure_ac97_clock: measured 54261 usecs intel8x0: clocking to 48000 8139cp 0000:02:09.0: This (id 10ec:8139 rev 10) is not an 8139C+ compatible chip 8139cp 0000:02:09.0: Try the "8139too" driver instead. 8139too Fast Ethernet driver 0.9.28 ACPI: PCI Interrupt 0000:02:09.0[A] -> GSI 23 (level, low) -> IRQ 17 eth0: RealTek RTL8139 at 0xe1632000, 00:0d:87:3c:3c:32, IRQ 17 eth0: Identified 8139 chip type 'RTL-8100B/8139D' Adding 1598456k swap on /dev/sda3. Priority:-1 extents:1 across:1598456k EXT3 FS on sda2, internal journal device-mapper: ioctl: 4.11.0-ioctl (2006-10-12) initialised: dm-devel@redhat.com loop: module loaded AppArmor: AppArmor initialized audit(1223709694.488:2): type=1505 info="AppArmor initialized" pid=1902 IA-32 Microcode Update Driver: v1.14a <tigran@aivazian.fsnet.co.uk> NET: Registered protocol family 10 lo: Disabled Privacy Extensions Mobile IPv6 ip6_tables: © 2000-2006 Netfilter Core Team powernow: This module only works with AMD K7 CPUs ip_tables: © 2000-2006 Netfilter Core Team Netfilter messages via NETLINK v0.30. nf_conntrack version 0.5.0 (4095 buckets, 32760 max) [drm] Initialized drm 1.1.0 20060810 ACPI: PCI Interrupt 0000:01:00.0[A] -> GSI 16 (level, low) -> IRQ 18 [drm] Initialized radeon 1.27.0 20060524 on minor 0 agpgart: Found an AGP 3.0 compliant device at 0000:00:00.0. agpgart: Putting AGP V3 device at 0000:00:00.0 into 8x mode agpgart: Putting AGP V3 device at 0000:01:00.0 into 8x mode audit(1223695306.140:3): audit_pid=3199 old=0 by auid=4294967295 [drm] Setting GART location based on new memory map [drm] Loading R300 Microcode [drm] writeback test succeeded in 1 usecs ISO 9660 Extensions: Microsoft Joliet Level 3 ISO 9660 Extensions: RRIP_1991A

Я вот ещё кой что нарыл

Код:

linux-v1nr:/ # wvdialconf Editing `/etc/wvdial.conf'. Scanning your serial ports for a modem. ttyS0<*1>: ATQ0 V1 E1 -- failed with 2400 baud, next try: 9600 baud ttyS0<*1>: ATQ0 V1 E1 -- failed with 9600 baud, next try: 115200 baud ttyS0<*1>: ATQ0 V1 E1 -- and failed too at 115200, giving up. Modem Port Scan<*1>: S1 S2 S3 ttyS4<Info>: No such device or address Modem Port Scan<*1>: S4 ttyS5<Info>: No such device or address Modem Port Scan<*1>: S5 ttyS6<Info>: No such device or address Modem Port Scan<*1>: S6 ttyS7<Info>: No such device or address Modem Port Scan<*1>: S7 Sorry, no modem was detected! Is it in use by another program? Did you configure it properly with setserial? Please read the FAQ at http://open.nit.ca/wiki/?WvDial If you still have problems, send mail to <wvdial-list@lists.nit.ca>. linux-v1nr:/ # cat /etc/wvdial.conf [Dialer Defaults] Modem = /dev/modem Baud = 57600 Init1 = ATZ Init2 = ATQ0 V1 E1 S0=0 &C1 &D2 Init3 = Area Code = Phone = 0 Username = Password = Ask Password = 0 Dial Command = ATDT Stupid Mode = 1 Compuserve = 0 Force Address = Idle Seconds = 300 DialMessage1 = DialMessage2 = ISDN = 0 Auto DNS = 1 linux-v1nr:/ # wvdial --> WvDial: Internet dialer version 1.56 (abuild@mandelbrot) --> Cannot open /dev/modem: No such file or directory --> Cannot open /dev/modem: No such file or directory --> Cannot open /dev/modem: No such file or directory linux-v1nr:/ # setserial -g /dev/ttyS0 /dev/ttyS1 /dev/ttyS2 /dev/ttyS3 /dev/ttyS0, UART: 16550A, Port: 0x03f8, IRQ: 4 /dev/ttyS1, UART: unknown, Port: 0x02f8, IRQ: 3 /dev/ttyS2, UART: unknown, Port: 0x03e8, IRQ: 4 /dev/ttyS3, UART: unknown, Port: 0x02e8, IRQ: 3 linux-v1nr:/ # setserial -a /dev/ttyS0 /dev/ttyS0, Line 0, UART: 16550A, Port: 0x03f8, IRQ: 4 Baud_base: 115200, close_delay: 50, divisor: 0 closing_wait: none Flags: spd_normal skip_test linux-v1nr:/ # stty -F /dev/ttyS0 speed 9600 baud; line = 0; -brkint -imaxbel

[BIgAndy]

Serial: 8250/16550 driver $Revision: 1.90 $ 4 ports, IRQ sharing enabled
serial8250: S0 at I/O 0x3f8 (irq = 4) is a 16550A
00:07: ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A

Ну вот оно. Если это не про строенный uart com-порта (что, вощемЮ одно и то же)
А wvdial настроен на /dev/modem
А он есть у вас? А если есть куда он симлинкнут? Если симлинкнут не туда, то симлинкните или моответсвенно настройте wvdial.

предварительно протестируйте minicom'ом свой модем at-командами.

[Mansai]

ну я перенастроил конфигурационный фаил wvdial.conf и теперь оно выдаёт при wvdial

Код: Выделить всё

linux-v1nr:/ # wvdial
--> WvDial: Internet dialer version 1.56 (abuild@mandelbrot)
--> Cannot open /dev/ttyS0: Device or resource is busy
--> Cannot open /dev/ttyS0: Device or resource is busy
--> Cannot open /dev/ttyS0: Device or resource is busy

Или что то вроде этого(печатаю по памяти)

[Mansai]

Вот ввёл команду wvdial под рутом (с настроеным портом). Программа начала посылать модему команды, но он не отвечает( пишет Modem not respoding али что вроде того).

[BIgAndy]

ну я перенастроил конфигурационный фаил wvdial.conf и теперь оно выдаёт при wvdial

Код: Выделить всё

linux-v1nr:/ # wvdial
--> WvDial: Internet dialer version 1.56 (abuild@mandelbrot)
--> Cannot open /dev/ttyS0: Device or resource is busy
--> Cannot open /dev/ttyS0: Device or resource is busy
--> Cannot open /dev/ttyS0: Device or resource is busy

Или что то вроде этого(печатаю по памяти)

Посмотрите, кто занял это устройство.

[Mansai]

Под рутом оно начинает посылать команды, но модем не отвечает, и тут проблемы уже наверное(хотя вот не знаю) в другом. Через Kinternet подключаюсь под юзером, тогда тоже начинает посылать команды, но всё равно - modem not respoding!!!!!!!!!!

[Mansai]

Код: Выделить всё

linux-v1nr:/ # setserial -g /dev/ttyS0 /dev/ttyS1 /dev/ttyS2 /dev/ttyS3
/dev/ttyS0, UART: 16550A, Port: 0x03f8, IRQ: 4
/dev/ttyS1, UART: unknown, Port: 0x02f8, IRQ: 3
/dev/ttyS2, UART: unknown, Port: 0x03e8, IRQ: 4
/dev/ttyS3, UART: unknown, Port: 0x02e8, IRQ: 3

IRQ порта - 4, а у модема (я посмотрел через YaST) IRQ - 3. Это может быть причиной?