Проблема с сетевым интерфейсом MCP61 (Отображается несколько сетевых интерфесов)

[seregarem]

Установил Mandriva 2007 (нужна именно эта версия), обнаруживается два или три сетевых интерфейса. Пробую удалить все и снова настроить сетевой интерфейс - Все работает нормально, но после перезагрузки снова два или три сетевых интерфейса. Сетевая плата встроенная, мать ASUS M2N-MX SE Plus. В чем проблема? Что можно сделать?

[rm_]

Приведите вывод dmesg, с большой вероятностью, лишний интерфейс - это ethernet-over-firewire, тут уже была подобная проблема.

[seregarem]

Код:

Bootdata ok (command line is BOOT_IMAGE=linux root=/dev/sda1 resume=/dev/sda5 v ga=788) Linux version 2.6.17-13mdv (rtp@octopus.mandriva.com) (gcc version 4.1.2 2007030 2 (prerelease) (4.1.2-1mdv2007.1)) #1 SMP Fri Mar 23 15:18:36 EDT 2007 BIOS-provided physical RAM map: BIOS-e820: 0000000000000000 - 000000000009fc00 (usable) BIOS-e820: 000000000009fc00 - 00000000000a0000 (reserved) BIOS-e820: 00000000000e4000 - 0000000000100000 (reserved) BIOS-e820: 0000000000100000 - 0000000077fb0000 (usable) BIOS-e820: 0000000077fb0000 - 0000000077fbe000 (ACPI data) BIOS-e820: 0000000077fbe000 - 0000000077fe0000 (ACPI NVS) BIOS-e820: 0000000077fe0000 - 0000000077fee000 (reserved) BIOS-e820: 0000000077ff0000 - 0000000078000000 (reserved) BIOS-e820: 00000000fec00000 - 00000000fec01000 (reserved) BIOS-e820: 00000000fee00000 - 00000000fef00000 (reserved) BIOS-e820: 00000000fff00000 - 0000000100000000 (reserved) DMI present. ACPI: RSDP (v000 ACPIAM ) @ 0x00000000000fb770 ACPI: RSDT (v001 A_M_I_ OEMRSDT 0x12000704 MSFT 0x00000097) @ 0x0000000077fb000 0 ACPI: FADT (v002 A_M_I_ OEMFACP 0x12000704 MSFT 0x00000097) @ 0x0000000077fb020 0 ACPI: MCFG (v001 A_M_I_ OEMMCFG 0x12000704 MSFT 0x00000097) @ 0x0000000077fb041 0 ACPI: OEMB (v001 A_M_I_ AMI_OEM 0x12000704 MSFT 0x00000097) @ 0x0000000077fbe04 0 ACPI: DSDT (v001 A0865 A0865000 0x00000000 INTL 0x20051117) @ 0x000000000000000 0 Scanning NUMA topology in Northbridge 24 Number of nodes 1 Node 0 MemBase 0000000000000000 Limit 0000000077fb0000 NUMA: Using 63 for the hash shift. Using node hash shift of 63 Bootmem setup node 0 0000000000000000-0000000077fb0000 On node 0 totalpages: 483467 DMA zone: 2785 pages, LIFO batch:0 DMA32 zone: 480682 pages, LIFO batch:31 Nvidia board detected. Ignoring ACPI timer override. ACPI: PM-Timer IO Port: 0x508 Intel MultiProcessor Specification v1.4 Virtual Wire compatibility mode. OEM ID: TEMPLATE Product ID: SE-Plus APIC at: 0xFEE00000 Processor #0 15:11 APIC version 16 Processor #1 15:11 APIC version 16 I/O APIC #2 Version 17 at 0xFEC00000. Setting APIC routing to physical flat Processors: 2 Allocating PCI resources starting at 80000000 (gap: 78000000:86c00000) Checking aperture... CPU 0: aperture @ 2170000000 size 32 MB Aperture from northbridge cpu 0 too small (32 MB) No AGP bridge found SMP: Allowing 2 CPUs, 0 hotplug CPUs Built 1 zonelists Kernel command line: BOOT_IMAGE=linux root=/dev/sda1 resume=/dev/sda5 vga=788 Initializing CPU#0 PID hash table entries: 4096 (order: 12, 32768 bytes) Disabling vsyscall due to use of PM timer time.c: Using 3.579545 MHz WALL PM GTOD PM timer. time.c: Detected 2310.521 MHz processor. Console: colour dummy device 80x25 Dentry cache hash table entries: 262144 (order: 9, 2097152 bytes) Inode-cache hash table entries: 131072 (order: 8, 1048576 bytes) Memory: 1929832k/1965760k available (2704k kernel code, 35540k reserved, 1014k d ata, 220k init) Calibrating delay using timer specific routine.. 4626.48 BogoMIPS (lpj=9252970) Mount-cache hash table entries: 256 CPU: L1 I Cache: 64K (64 bytes/line), D cache 64K (64 bytes/line) CPU: L2 Cache: 512K (64 bytes/line) CPU 0/0(2) -> Node 0 -> Core 0 SMP alternatives: switching to UP code checking if image is initramfs... it is Freeing initrd memory: 783k freed ACPI: Looking for DSDT in initramfs... error, file /DSDT.aml not found. ACPI: setting ELCR to 0200 (from 0c20) ExtINT not setup in hardware but reported by MP table Using IO-APIC 2 ..MP-BIOS bug: 8254 timer not connected to IO-APIC Using local APIC timer interrupts. result 12557192 Detected 12.557 MHz APIC timer. SMP alternatives: switching to SMP code Booting processor 1/2 APIC 0x1 Initializing CPU#1 Calibrating delay using timer specific routine.. 4621.44 BogoMIPS (lpj=9242893) CPU: L1 I Cache: 64K (64 bytes/line), D cache 64K (64 bytes/line) CPU: L2 Cache: 512K (64 bytes/line) CPU 1/1(2) -> Node 0 -> Core 1 AMD Athlon&#153; 64 X2 Dual Core Processor 4400+ stepping 02 CPU 1: Syncing TSC to CPU 0. CPU 1: synchronized TSC with CPU 0 (last diff -3 cycles, maxerr 573 cycles) Brought up 2 CPUs testing NMI watchdog ... OK. migration_cost=178 NET: Registered protocol family 16 ACPI: bus type pci registered PCI: BIOS Bug: MCFG area at e0000000 is not E820-reserved PCI: Not using MMCONFIG. PCI: Using configuration type 1 ACPI: Subsystem revision 20060127 ACPI: Interpreter enabled ACPI: Using PIC for interrupt routing Error attaching device data Error attaching device data Error attaching device data Error attaching device data ACPI: PCI Root Bridge [PCI0] (0000:00) PCI: Probing PCI hardware (bus 00) Boot video device is 0000:00:0d.0 PCI: Transparent bridge - 0000:00:04.0 ACPI: PCI Interrupt Routing Table [\_SB_.PCI0._PRT] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.P0P1._PRT] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.P0P2._PRT] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.BR11._PRT] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.BR12._PRT] ACPI: PCI Interrupt Link [LNKA] (IRQs 5 7 10 11 14) *0, disabled. ACPI: PCI Interrupt Link [LNKB] (IRQs 5 7 10 11 14) *0, disabled. ACPI: PCI Interrupt Link [LNKC] (IRQs 5 7 10 11 14) *0, disabled. ACPI: PCI Interrupt Link [LNKD] (IRQs 5 7 10 11 14) *0, disabled. ACPI: PCI Interrupt Link [LNEA] (IRQs 5 7 10 11 14) *0, disabled. ACPI: PCI Interrupt Link [LNEB] (IRQs 5 7 10 11 14) *0, disabled. ACPI: PCI Interrupt Link [LNEC] (IRQs 5 7 10 11 14) *0, disabled. ACPI: PCI Interrupt Link [LNED] (IRQs 5 7 10 11 14) *0, disabled. ACPI: PCI Interrupt Link [LUB0] (IRQs *5 7 10 11 14) ACPI: PCI Interrupt Link [LUB2] (IRQs 5 7 10 *11 14) ACPI: PCI Interrupt Link [LMAC] (IRQs *5 7 10 11 14) ACPI: PCI Interrupt Link [LAZA] (IRQs 5 7 *10 11 14) ACPI: PCI Interrupt Link [LACI] (IRQs 5 7 10 11 14) *0, disabled. ACPI: PCI Interrupt Link [LMC9] (IRQs 5 7 10 *11 14) ACPI: PCI Interrupt Link [LSMB] (IRQs 5 7 *10 11 14) ACPI: PCI Interrupt Link [LPMU] (IRQs 5 7 10 11 14) *0, disabled. ACPI: PCI Interrupt Link [LSA0] (IRQs 5 7 10 *11 14) ACPI: PCI Interrupt Link [LSA1] (IRQs 5 7 10 11 14) *0, disabled. ACPI: PCI Interrupt Link [LATA] (IRQs 5 7 10 11 14) *0, disabled. PCI: Using ACPI for IRQ routing PCI: If a device doesn't work, try "pci=routeirq". If it helps, post a report PCI-DMA: Disabling IOMMU. PCI: Bridge: 0000:00:04.0 IO window: disabled. MEM window: disabled. PREFETCH window: disabled. PCI: Bridge: 0000:00:09.0 IO window: disabled. MEM window: disabled. PREFETCH window: disabled. PCI: Bridge: 0000:00:0b.0 IO window: disabled. MEM window: disabled. PREFETCH window: disabled. PCI: Bridge: 0000:00:0c.0 IO window: disabled. MEM window: disabled. PREFETCH window: disabled. PCI: Setting latency timer of device 0000:00:04.0 to 64 PCI: Setting latency timer of device 0000:00:09.0 to 64 PCI: Setting latency timer of device 0000:00:0b.0 to 64 PCI: Setting latency timer of device 0000:00:0c.0 to 64 NET: Registered protocol family 2 IP route cache hash table entries: 65536 (order: 7, 524288 bytes) TCP established hash table entries: 262144 (order: 10, 4194304 bytes) TCP bind hash table entries: 65536 (order: 8, 1048576 bytes) TCP: Hash tables configured (established 262144 bind 65536) TCP reno registered IA32 emulation $Id: sys_ia32.c,v 1.32 2002/03/24 13:02:28 ak Exp $ audit: initializing netlink socket (disabled) audit(1224822849.348:1): initialized Total HugeTLB memory allocated, 0 VFS: Disk quotas dquot_6.5.1 Dquot-cache hash table entries: 512 (order 0, 4096 bytes) Initializing Cryptographic API io scheduler noop registered io scheduler anticipatory registered (default) io scheduler deadline registered io scheduler cfq registered PCI: Setting latency timer of device 0000:00:09.0 to 64 pcie_portdrv_probe->Dev[03e8:10de] has invalid IRQ. Check vendor BIOS assign_interrupt_mode Found MSI capability Allocate Port Service[0000:00:09.0:pcie00] PCI: Setting latency timer of device 0000:00:0b.0 to 64 pcie_portdrv_probe->Dev[03e9:10de] has invalid IRQ. Check vendor BIOS assign_interrupt_mode Found MSI capability Allocate Port Service[0000:00:0b.0:pcie00] PCI: Setting latency timer of device 0000:00:0c.0 to 64 pcie_portdrv_probe->Dev[03e9:10de] has invalid IRQ. Check vendor BIOS assign_interrupt_mode Found MSI capability Allocate Port Service[0000:00:0c.0:pcie00] vesafb: framebuffer at 0xc0000000, mapped to 0xffffc20000080000, using 3750k, to tal 131072k vesafb: mode is 800x600x16, linelength=1600, pages=2 vesafb: scrolling: redraw vesafb: Truecolor: size=0:5:6:5, shift=0:11:5:0 bootsplash 3.1.6-2004/03/31: looking for picture...<6> silentjpeg size 160830 by tes,<6>...found (800x600, 160782 bytes, v3). Console: switching to colour frame buffer device 93x31 fb0: VESA VGA frame buffer device Real Time Clock Driver v1.12ac Linux agpgart interface v0.101 © Dave Jones Serial: 8250/16550 driver $Revision: 1.90 $ 4 ports, IRQ sharing enabled serial8250: ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A RAMDISK driver initialized: 16 RAM disks of 32000K size 1024 blocksize Uniform Multi-Platform E-IDE driver Revision: 7.00alpha2 ide: Assuming 33MHz system bus speed for PIO modes; override with idebus=xx NFORCE-MCP61: IDE controller at PCI slot 0000:00:06.0 NFORCE-MCP61: chipset revision 162 NFORCE-MCP61: not 100% native mode: will probe irqs later NFORCE-MCP61: 0000:00:06.0 (rev a2) UDMA133 controller ide0: BM-DMA at 0xffa0-0xffa7, BIOS settings: hda:pio, hdb:DMA Probing IDE interface ide0... hdb: LITE-ON DVD SOHD-167T, ATAPI CD/DVD-ROM drive ide0 at 0x1f0-0x1f7,0x3f6 on irq 14 serio: i8042 AUX port at 0x60,0x64 irq 12 serio: i8042 KBD port at 0x60,0x64 irq 1 mice: PS/2 mouse device common for all mice md: md driver 0.90.3 MAX_MD_DEVS=256, MD_SB_DISKS=27 md: bitmap version 4.39 TCP bic registered NET: Registered protocol family 1 ACPI wakeup devices: PS2K PS2M UAR1 USB0 USB2 P0P1 HDAC P0P2 BR11 NMAC NSMB ACPI: (supports S0 S1 S3 S4 S5) BIOS EDD facility v0.16 2004-Jun-25, 1 devices found Freeing unused kernel memory: 220k freed SCSI subsystem initialized libata version 1.20 loaded. input: AT Translated Set 2 keyboard as /class/input/input0 sata_nv 0000:00:08.0: version 0.8 ACPI: PCI Interrupt Link [LSA0] enabled at IRQ 11 PCI: setting IRQ 11 as level-triggered ACPI: PCI Interrupt 0000:00:08.0[A] -> Link [LSA0] -> GSI 11 (level, low) -> IRQ 11 PCI: Setting latency timer of device 0000:00:08.0 to 64 ata1: SATA max UDMA/133 cmd 0xE400 ctl 0xE082 bmdma 0xD880 irq 11 ata2: SATA max UDMA/133 cmd 0xE000 ctl 0xDC02 bmdma 0xD888 irq 11 ata1: SATA link up 1.5 Gbps (SStatus 113) ata1: dev 0 cfg 49:2f00 82:346b 83:7d01 84:4023 85:3469 86:3c01 87:4023 88:407f ata1: dev 0 ATA-7, max UDMA/133, 312581808 sectors: LBA48 ata1: dev 0 configured for UDMA/133 scsi0 : sata_nv ata2: SATA link down (SStatus 0) scsi1 : sata_nv Vendor: ATA Model: ST3160815AS Rev: 4.AA Type: Direct-Access ANSI SCSI revision: 05 SCSI device sda: 312581808 512-byte hdwr sectors (160042 MB) sda: Write Protect is off sda: Mode Sense: 00 3a 00 00 SCSI device sda: drive cache: write back SCSI device sda: 312581808 512-byte hdwr sectors (160042 MB) sda: Write Protect is off sda: Mode Sense: 00 3a 00 00 SCSI device sda: drive cache: write back sda: sda1 sda2 < sda5<6>input: ImPS/2 Generic Wheel Mouse as /class/input/input 1 sda6 > sd 0:0:0:0: Attached scsi disk sda kjournald starting. Commit interval 5 seconds EXT3-fs: mounted filesystem with ordered data mode. ts: Compaq touchscreen protocol output usbcore: registered new driver usbfs usbcore: registered new driver hub ohci_hcd: 2005 April 22 USB 1.1 'Open' Host Controller (OHCI) Driver (PCI) ACPI: PCI Interrupt Link [LUB0] enabled at IRQ 5 PCI: setting IRQ 5 as level-triggered ACPI: PCI Interrupt 0000:00:02.0[A] -> Link [LUB0] -> GSI 5 (level, low) -> IRQ 5 PCI: Setting latency timer of device 0000:00:02.0 to 64 ohci_hcd 0000:00:02.0: OHCI Host Controller ohci_hcd 0000:00:02.0: new USB bus registered, assigned bus number 1 ohci_hcd 0000:00:02.0: irq 5, io mem 0xdffff000 usb usb1: configuration #1 chosen from 1 choice hub 1-0:1.0: USB hub found hub 1-0:1.0: 8 ports detected ACPI: PCI Interrupt Link [LUB2] enabled at IRQ 11 ACPI: PCI Interrupt 0000:00:02.1[B] -> Link [LUB2] -> GSI 11 (level, low) -> IRQ 11 PCI: Setting latency timer of device 0000:00:02.1 to 64 ehci_hcd 0000:00:02.1: EHCI Host Controller ehci_hcd 0000:00:02.1: new USB bus registered, assigned bus number 2 ehci_hcd 0000:00:02.1: debug port 1 PCI: cache line size of 64 is not supported by device 0000:00:02.1 ehci_hcd 0000:00:02.1: irq 11, io mem 0xdfffec00 ehci_hcd 0000:00:02.1: USB 2.0 started, EHCI 1.00, driver 10 Dec 2004 usb usb2: configuration #1 chosen from 1 choice hub 2-0:1.0: USB hub found hub 2-0:1.0: 8 ports detected powernow-k8: Found 2 AMD Athlon 64 / Opteron processors (version 1.60.2) powernow-k8: MP systems not supported by PSB BIOS structure powernow-k8: MP systems not supported by PSB BIOS structure Floppy drive(s): fd0 is 1.44M FDC 0 is a post-1991 82077 device-mapper: 4.6.0-ioctl (2006-02-17) initialised: dm-devel@redhat.com EXT3 FS on sda1, internal journal Adding 4088500k swap on /dev/sda5. Priority:-1 extents:1 across:4088500k kjournald starting. Commit interval 5 seconds EXT3 FS on sda6, internal journal EXT3-fs: mounted filesystem with ordered data mode. loop: loaded (max 8 devices, max 1 partitions per device) hdb: ATAPI 48X DVD-ROM drive, 512kB Cache, UDMA(33) Uniform CD-ROM driver Revision: 3.20 Netfilter messages via NETLINK v0.30. ip_conntrack version 2.4 (8192 buckets, 65536 max) - 304 bytes per conntrack ACPI: Power Button (FF) [PWRF] ACPI: Power Button (CM) [PWRB] Removing netfilter NETLINK layer. NET: Registered protocol family 10 lo: Disabled Privacy Extensions IPv6 over IPv4 tunneling driver process `sysctl' is using deprecated sysctl (syscall) net.ipv6.neigh.lo.base_rea chable_time; Use net.ipv6.neigh.lo.base_reachable_time_ms instead. NET: Registered protocol family 17 forcedeth.c: Reverse Engineered nForce ethernet driver. Version 0.54. ACPI: PCI Interrupt Link [LMAC] enabled at IRQ 5 ACPI: PCI Interrupt 0000:00:07.0[A] -> Link [LMAC] -> GSI 5 (level, low) -> IRQ 5 PCI: Setting latency timer of device 0000:00:07.0 to 64 forcedeth: using HIGHDMA 0000:00:07.0: Invalid Mac address detected: 4b:65:66:8c:1e:00 Please complain to your hardware vendor. Switching to a random MAC. eth0: forcedeth.c: subsystem: 01043:8234 bound to 0000:00:07.0 eth9: no link during initialization. ADDRCONF(NETDEV_UP): eth9: link is not ready eth9: link up. ADDRCONF(NETDEV_CHANGE): eth9: link becomes ready eth9: no IPv6 routers present ip_tables: © 2000-2006 Netfilter Core Team Netfilter messages via NETLINK v0.30. ip_conntrack version 2.4 (8192 buckets, 65536 max) - 304 bytes per conntrack Installing knfsd (copyright © 1996 okir@monad.swb.de). NFSD: Using /var/lib/nfs/v4recovery as the NFSv4 state recovery directory NFSD: starting 90-second grace period ip_conntrack_pptp version 3.1 loaded nvidia: module license 'NVIDIA' taints kernel. ACPI: PCI Interrupt Link [LMC9] enabled at IRQ 11 ACPI: PCI Interrupt 0000:00:0d.0[A] -> Link [LMC9] -> GSI 11 (level, low) -> IRQ 11 PCI: Setting latency timer of device 0000:00:0d.0 to 64 NVRM: loading NVIDIA UNIX x86_64 Kernel Module 1.0-9755 Mon Feb 26 23:16:31 PS T 2007 ip_nat_pptp version 3.0 loaded ClusterIP Version 0.8 loaded successfully ipt_recent v0.3.1: Stephen Frost <sfrost@snowman.net>. http://snowman.net/proje cts/ipt_recent/ netfilter PSD loaded - © astaro AG IFWLOG: register target bootsplash 3.1.6-2004/03/31: looking for picture...<6>...found (800x600, 14222 b ytes, v3). bootsplash: status on console 0 changed to on bootsplash 3.1.6-2004/03/31: looking for picture...<6>...found (800x600, 14222 b ytes, v3). bootsplash: status on console 1 changed to on bootsplash 3.1.6-2004/03/31: looking for picture...<6>...found (800x600, 14222 b ytes, v3). bootsplash: status on console 2 changed to on bootsplash 3.1.6-2004/03/31: looking for picture...<6>...found (800x600, 14222 b ytes, v3). bootsplash: status on console 3 changed to on bootsplash 3.1.6-2004/03/31: looking for picture...<6>...found (800x600, 14222 b ytes, v3). bootsplash: status on console 4 changed to on bootsplash 3.1.6-2004/03/31: looking for picture...<6>...found (800x600, 14222 b ytes, v3). bootsplash: status on console 5 changed to on irq 5: nobody cared (try booting with the "irqpoll" option) Call Trace: <IRQ> <ffffffff801c13f5>{__report_bad_irq+53} <ffffffff801c1670>{note_interrupt+544} <ffffffff88082b68>{:usbcore:usb_hc d_irq+40} <ffffffff801c0ce0>{__do_IRQ+224} <ffffffff8010ceb4>{do_IRQ+68} <ffffffff80108d90>{default_idle+0} <ffffffff8010a32c>{ret_from_intr+0} <E OI> <ffffffff803a001f>{thread_return+0} <ffffffff8039aff0>{unix_poll+0} <ffffffff80108dbb>{default_idle+43} <ffffffff80108e90>{cpu_idle+160} <ffffffff8053e854>{start_kernel+516} <ffffffff8053e294>{_sinittext+660} handlers: [<ffffffff88082b40>] (usb_hcd_irq+0x0/0x60 [usbcore]) Disabling IRQ #5

[Rootlexx]

seregarem
В качестве временного решения можете отключить службу «harddrake» — скорее всего, именно она обнаруживает и настраивает ваши сетевые интерфейсы.