После подключения девайса получаю
Код: Выделить всё
$ dmesg | grep [Uu]sb
[ 30.384489] usbcore: registered new interface driver usbfs
[ 30.384516] usbcore: registered new interface driver hub
[ 30.393018] usbcore: registered new device driver usb
[ 30.404359] usb usb1: configuration #1 chosen from 1 choice
[ 30.507734] usb usb2: configuration #1 chosen from 1 choice
[ 30.611585] usb usb3: configuration #1 chosen from 1 choice
[ 30.735151] usb usb4: configuration #1 chosen from 1 choice
[ 31.134237] usb 4-6: new high speed USB device using ehci_hcd and address 2
[ 31.266908] usb 4-6: configuration #1 chosen from 1 choice
[ 31.379565] usbcore: registered new interface driver libusual
[ 31.388329] usbcore: registered new interface driver usb-storage
[ 31.388440] usb-storage: device found at 2
[ 31.388442] usb-storage: waiting for device to settle before scanning
[ 36.376171] usb-storage: device scan complete
[ 41.977154] usb 4-6: reset high speed USB device using ehci_hcd and address 2
[ 47.709991] usb 4-6: reset high speed USB device using ehci_hcd and address 2
[ 53.442854] usb 4-6: reset high speed USB device using ehci_hcd and address 2
[ 59.175718] usb 4-6: reset high speed USB device using ehci_hcd and address 2
Код: Выделить всё
# cat /proc/bus/usb/devices
T: Bus=04 Lev=00 Prnt=00 Port=00 Cnt=00 Dev#= 1 Spd=480 MxCh= 6
B: Alloc= 0/800 us ( 0%), #Int= 0, #Iso= 0
D: Ver= 2.00 Cls=09(hub ) Sub=00 Prot=01 MxPS=64 #Cfgs= 1
P: Vendor=0000 ProdID=0000 Rev= 2.06
S: Manufacturer=Linux 2.6.24-21-generic ehci_hcd
S: Product=EHCI Host Controller
S: SerialNumber=0000:00:1d.7
C:* #Ifs= 1 Cfg#= 1 Atr=e0 MxPwr= 0mA
I:* If#= 0 Alt= 0 #EPs= 1 Cls=09(hub ) Sub=00 Prot=00 Driver=hub
E: Ad=81(I) Atr=03(Int.) MxPS= 4 Ivl=256ms
T: Bus=04 Lev=01 Prnt=01 Port=05 Cnt=01 Dev#= 2 Spd=480 MxCh= 0
D: Ver= 2.00 Cls=00(>ifc ) Sub=00 Prot=00 MxPS=64 #Cfgs= 1
P: Vendor=04cf ProdID=8818 Rev=b0.08
S: Manufacturer=Myson Century, Inc.
S: Product=USB Mass Storage Device
S: SerialNumber=100
C:* #Ifs= 1 Cfg#= 1 Atr=c0 MxPwr= 10mA
I:* If#= 0 Alt= 0 #EPs= 2 Cls=08(stor.) Sub=05 Prot=50 Driver=usb-storage
E: Ad=03(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E: Ad=84(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
T: Bus=03 Lev=00 Prnt=00 Port=00 Cnt=00 Dev#= 1 Spd=12 MxCh= 2
B: Alloc= 0/900 us ( 0%), #Int= 0, #Iso= 0
D: Ver= 1.10 Cls=09(hub ) Sub=00 Prot=00 MxPS=64 #Cfgs= 1
P: Vendor=0000 ProdID=0000 Rev= 2.06
S: Manufacturer=Linux 2.6.24-21-generic uhci_hcd
S: Product=UHCI Host Controller
S: SerialNumber=0000:00:1d.2
C:* #Ifs= 1 Cfg#= 1 Atr=e0 MxPwr= 0mA
I:* If#= 0 Alt= 0 #EPs= 1 Cls=09(hub ) Sub=00 Prot=00 Driver=hub
E: Ad=81(I) Atr=03(Int.) MxPS= 2 Ivl=255ms
T: Bus=02 Lev=00 Prnt=00 Port=00 Cnt=00 Dev#= 1 Spd=12 MxCh= 2
B: Alloc= 0/900 us ( 0%), #Int= 0, #Iso= 0
D: Ver= 1.10 Cls=09(hub ) Sub=00 Prot=00 MxPS=64 #Cfgs= 1
P: Vendor=0000 ProdID=0000 Rev= 2.06
S: Manufacturer=Linux 2.6.24-21-generic uhci_hcd
S: Product=UHCI Host Controller
S: SerialNumber=0000:00:1d.1
C:* #Ifs= 1 Cfg#= 1 Atr=e0 MxPwr= 0mA
I:* If#= 0 Alt= 0 #EPs= 1 Cls=09(hub ) Sub=00 Prot=00 Driver=hub
E: Ad=81(I) Atr=03(Int.) MxPS= 2 Ivl=255ms
T: Bus=01 Lev=00 Prnt=00 Port=00 Cnt=00 Dev#= 1 Spd=12 MxCh= 2
B: Alloc= 0/900 us ( 0%), #Int= 0, #Iso= 0
D: Ver= 1.10 Cls=09(hub ) Sub=00 Prot=00 MxPS=64 #Cfgs= 1
P: Vendor=0000 ProdID=0000 Rev= 2.06
S: Manufacturer=Linux 2.6.24-21-generic uhci_hcd
S: Product=UHCI Host Controller
S: SerialNumber=0000:00:1d.0
C:* #Ifs= 1 Cfg#= 1 Atr=e0 MxPwr= 0mA
I:* If#= 0 Alt= 0 #EPs= 1 Cls=09(hub ) Sub=00 Prot=00 Driver=hub
E: Ad=81(I) Atr=03(Int.) MxPS= 2 Ivl=255ms
Код: Выделить всё
# lsusb
Bus 004 Device 002: ID 04cf:8818 Myson Century, Inc. USB2.0 to ATAPI Bridge Controller
Bus 004 Device 001: ID 0000:0000
Bus 003 Device 001: ID 0000:0000
Bus 002 Device 001: ID 0000:0000
Bus 001 Device 001: ID 0000:0000
При подключении IDE винта его не видно. В какую сторону копать что б исправить ситуэйшен? По офтопиком видно, даже видно с лайв-сд акрониса.