OS: Debian Experimental
Мышь: Microsoft Basic Optical Mouse 1.0A. Model: 1094.
Модули в ядро подгружены: usbcore, usbhid, usbmouse.
Код: Выделить всё
# lsusb
Bus 006 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub
Bus 005 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub
Bus 004 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub
Bus 003 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub
Bus 002 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub
Bus 001 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hubКод:
# dmesg
[ 0.000000] Initializing cgroup subsys cpuset
[ 0.000000] Initializing cgroup subsys cpu
[ 0.000000] Linux version 2.6.26-1-686 (Debian 2.6.26-10) (waldi@debian.org) (gcc version 4.1.3 20080623 (prerelease) (Debian 4.1.2-23)) #1 SMP Sat Nov 8 19:00:26 UTC 2008
[ 0.000000] BIOS-provided physical RAM map:
[ 0.000000] BIOS-e820: 0000000000000000 - 000000000009fc00 (usable)
[ 0.000000] BIOS-e820: 000000000009fc00 - 00000000000a0000 (reserved)
[ 0.000000] BIOS-e820: 00000000000e0000 - 0000000000100000 (reserved)
[ 0.000000] BIOS-e820: 0000000000100000 - 000000001bfa8000 (usable)
[ 0.000000] BIOS-e820: 000000001bfa8000 - 000000001bfb0000 (ACPI NVS)
[ 0.000000] BIOS-e820: 000000001bfb0000 - 000000001bfbe000 (ACPI data)
[ 0.000000] BIOS-e820: 000000001bfbe000 - 000000001bff0000 (ACPI NVS)
[ 0.000000] BIOS-e820: 000000001bff0000 - 000000001c000000 (reserved)
[ 0.000000] BIOS-e820: 00000000fee00000 - 00000000fee01000 (reserved)
[ 0.000000] BIOS-e820: 00000000ffb80000 - 0000000100000000 (reserved)
[ 0.000000] 0MB HIGHMEM available.
[ 0.000000] 447MB LOWMEM available.
[ 0.000000] found SMP MP-table at [c00ff780] 000ff780
[ 0.000000] Entering add_active_range(0, 0, 114600) 0 entries of 256 used
[ 0.000000] Zone PFN ranges:
[ 0.000000] DMA 0 -> 4096
[ 0.000000] Normal 4096 -> 114600
[ 0.000000] HighMem 114600 -> 114600
[ 0.000000] Movable zone start PFN for each node
[ 0.000000] early_node_map[1] active PFN ranges
[ 0.000000] 0: 0 -> 114600
[ 0.000000] On node 0 totalpages: 114600
[ 0.000000] DMA zone: 32 pages used for memmap
[ 0.000000] DMA zone: 0 pages reserved
[ 0.000000] DMA zone: 4064 pages, LIFO batch:0
[ 0.000000] Normal zone: 864 pages used for memmap
[ 0.000000] Normal zone: 109640 pages, LIFO batch:31
[ 0.000000] HighMem zone: 0 pages used for memmap
[ 0.000000] Movable zone: 0 pages used for memmap
[ 0.000000] DMI 2.4 present.
[ 0.000000] ACPI: RSDP 000F7F50, 0024 (r2 ACPIAM)
[ 0.000000] ACPI: XSDT 1BFB0100, 005C (r1 A.M.I OEMXSDT 3000720 MSFT 97)
[ 0.000000] ACPI: FACP 1BFB0290, 00F4 (r3 A.M.I OEMFACP 3000720 MSFT 97)
[ 0.000000] ACPI: DSDT 1BFB0630, 7732 (r1 T12R0 T12R0000 0 INTL 20051117)
[ 0.000000] ACPI: FACS 1BFBE000, 0040
[ 0.000000] ACPI: APIC 1BFB0390, 005C (r1 A.M.I OEMAPIC 3000720 MSFT 97)
[ 0.000000] ACPI: MCFG 1BFB03F0, 003C (r1 A.M.I OEMMCFG 3000720 MSFT 97)
[ 0.000000] ACPI: SLIC 1BFB0430, 0176 (r1 A.M.I OEMSLIC 3000720 MSFT 97)
[ 0.000000] ACPI: BOOT 1BFB0600, 0028 (r1 A.M.I OEMBOOT 3000720 MSFT 97)
[ 0.000000] ACPI: OEMB 1BFBE040, 005B (r1 A.M.I AMI_OEM 3000720 MSFT 97)
[ 0.000000] ACPI: SSDT 1BFBE2A0, 01EF (r1 AMI CPU_CST 1 INTL 20051117)
[ 0.000000] ATI board detected. Disabling timer routing over 8254.
[ 0.000000] ACPI: PM-Timer IO Port: 0x808
[ 0.000000] ACPI: Local APIC address 0xfee00000
[ 0.000000] ACPI: LAPIC (acpi_id[0x01] lapic_id[0x00] enabled)
[ 0.000000] ACPI: LAPIC (acpi_id[0x02] lapic_id[0x81] disabled)
[ 0.000000] ACPI: IOAPIC (id[0x01] address[0xfec00000] gsi_base[0])
[ 0.000000] IOAPIC[0]: apic_id 1, version 33, address 0xfec00000, GSI 0-23
[ 0.000000] ACPI: INT_SRC_OVR (bus 0 bus_irq 0 global_irq 2 dfl dfl)
[ 0.000000] ACPI: INT_SRC_OVR (bus 0 bus_irq 9 global_irq 9 low level)
[ 0.000000] ACPI: IRQ0 used by override.
[ 0.000000] ACPI: IRQ2 used by override.
[ 0.000000] ACPI: IRQ9 used by override.
[ 0.000000] Enabling APIC mode: Flat. Using 1 I/O APICs
[ 0.000000] Using ACPI (MADT) for SMP configuration information
[ 0.000000] Allocating PCI resources starting at 20000000 (gap: 1c000000:e2e00000)
[ 0.000000] PM: Registered nosave memory: 000000000009f000 - 00000000000a0000
[ 0.000000] PM: Registered nosave memory: 00000000000a0000 - 00000000000e0000
[ 0.000000] PM: Registered nosave memory: 00000000000e0000 - 0000000000100000
[ 0.000000] SMP: Allowing 2 CPUs, 1 hotplug CPUs
[ 0.000000] PERCPU: Allocating 37960 bytes of per cpu data
[ 0.000000] NR_CPUS: 8, nr_cpu_ids: 2
[ 0.000000] Built 1 zonelists in Zone order, mobility grouping on. Total pages: 113704
[ 0.000000] Kernel command line: BOOT_IMAGE=/boot/vmlinuz-2.6.26-1-686 root=UUID=45a5f34d-f09f-4b89-9071-a09de53431fe ro quiet
[ 0.000000] mapped APIC to ffffb000 (fee00000)
[ 0.000000] mapped IOAPIC to ffffa000 (fec00000)
[ 0.000000] Enabling fast FPU save and restore... done.
[ 0.000000] Enabling unmasked SIMD FPU exception support... done.
[ 0.000000] Initializing CPU#0
[ 0.000000] PID hash table entries: 2048 (order: 11, 8192 bytes)
[ 0.000000] Extended CMOS year: 2000
[ 0.000000] Detected 1596.148 MHz processor.
[ 0.004000] Console: colour VGA+ 80x25
[ 0.004000] console [tty0] enabled
[ 0.004000] Dentry cache hash table entries: 65536 (order: 6, 262144 bytes)
[ 0.004000] Inode-cache hash table entries: 32768 (order: 5, 131072 bytes)
[ 0.004000] Memory: 442820k/458400k available (1768k kernel code, 15096k reserved, 752k data, 244k init, 0k highmem)
[ 0.004000] virtual kernel memory layout:
[ 0.004000] fixmap : 0xfff4c000 - 0xfffff000 ( 716 kB)
[ 0.004000] pkmap : 0xff800000 - 0xffc00000 (4096 kB)
[ 0.004000] vmalloc : 0xdc800000 - 0xff7fe000 ( 559 MB)
[ 0.004000] lowmem : 0xc0000000 - 0xdbfa8000 ( 447 MB)
[ 0.004000] .init : 0xc037f000 - 0xc03bc000 ( 244 kB)
[ 0.004000] .data : 0xc02ba30b - 0xc0376620 ( 752 kB)
[ 0.004000] .text : 0xc0100000 - 0xc02ba30b (1768 kB)
[ 0.004000] Checking if this processor honours the WP bit even in supervisor mode...Ok.
[ 0.004000] CPA: page pool initialized 1 of 1 pages preallocated
[ 0.084090] Calibrating delay using timer specific routine.. 3196.15 BogoMIPS (lpj=6392302)
[ 0.084130] Security Framework initialized
[ 0.084135] SELinux: Disabled at boot.
[ 0.084139] Capability LSM initialized
[ 0.084154] Mount-cache hash table entries: 512
[ 0.084301] Initializing cgroup subsys ns
[ 0.084306] Initializing cgroup subsys cpuacct
[ 0.084309] Initializing cgroup subsys devices
[ 0.084329] CPU: L1 I cache: 32K, L1 D cache: 32K
[ 0.084332] CPU: L2 cache: 1024K
[ 0.084337] Intel machine check architecture supported.
[ 0.084342] Intel machine check reporting enabled on CPU#0.
[ 0.084344] using mwait in idle threads.
[ 0.084354] Checking 'hlt' instruction... OK.
[ 0.100437] SMP alternatives: switching to UP code
[ 0.106503] ACPI: Core revision 20080321
[ 0.124308] ENABLING IO-APIC IRQs
[ 0.124502] ..TIMER: vector=0x31 apic1=0 pin1=2 apic2=-1 pin2=-1
[ 0.164203] CPU0: Intel® Celeron® M CPU 520 @ 1.60GHz stepping 06
[ 0.168010] Brought up 1 CPUs
[ 0.168010] Total of 1 processors activated (3196.15 BogoMIPS).
[ 0.168010] CPU0 attaching sched-domain:
[ 0.168010] domain 0: span 0
[ 0.168010] groups: 0
[ 0.168010] net_namespace: 660 bytes
[ 0.168010] Booting paravirtualized kernel on bare hardware
[ 0.168010] NET: Registered protocol family 16
[ 0.168010] ACPI FADT declares the system doesn't support PCIe ASPM, so disable it
[ 0.168010] ACPI: bus type pci registered
[ 0.168010] PCI: MCFG configuration 0: base e0000000 segment 0 buses 0 - 255
[ 0.168010] PCI: Not using MMCONFIG.
[ 0.168010] PCI: PCI BIOS revision 3.00 entry at 0xf0031, last bus=9
[ 0.168010] PCI: Using configuration type 1 for base access
[ 0.168010] Setting up standard PCI resources
[ 0.168010] ACPI: EC: Look up EC in DSDT
[ 0.208013] ACPI: Interpreter enabled
[ 0.208013] ACPI: (supports S0 S1 S3 S4 S5)
[ 0.208013] ACPI: Using IOAPIC for interrupt routing
[ 0.208013] PCI: MCFG configuration 0: base e0000000 segment 0 buses 0 - 255
[ 0.210284] PCI: MCFG area at e0000000 reserved in ACPI motherboard resources
[ 0.210287] PCI: Using MMCONFIG for extended config space
[ 0.219620] ACPI: EC: GPE = 0x11, I/O: command/status = 0x66, data = 0x62
[ 0.219623] ACPI: EC: driver started in poll mode
[ 0.219762] ACPI: PCI Root Bridge [PCI0] (0000:00)
[ 0.220013] pci 0000:00:12.0: set SATA to AHCI mode
[ 0.221751] PCI: Transparent bridge - 0000:00:14.4
[ 0.221826] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0._PRT]
[ 0.222040] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.P0P1._PRT]
[ 0.222280] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.PCE4._PRT]
[ 0.222440] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.PCE6._PRT]
[ 0.222597] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.PCE7._PRT]
[ 0.222770] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.P0PC._PRT]
[ 0.222960] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.PCE5._PRT]
[ 0.228996] ACPI: PCI Interrupt Link [LNKA] (IRQs 3 4 5 6 *11 12)
[ 0.229175] ACPI: PCI Interrupt Link [LNKB] (IRQs 3 4 *5 6 12)
[ 0.229353] ACPI: PCI Interrupt Link [LNKC] (IRQs 3 *4 5 6 12)
[ 0.229528] ACPI: PCI Interrupt Link [LNKD] (IRQs 3 4 5 6 12) *10
[ 0.229704] ACPI: PCI Interrupt Link [LNKE] (IRQs 3 4 *5 12)
[ 0.229879] ACPI: PCI Interrupt Link [LNKF] (IRQs 3 4 *5 12)
[ 0.230053] ACPI: PCI Interrupt Link [LNKG] (IRQs *3 4 5 6 12)
[ 0.230229] ACPI: PCI Interrupt Link [LNKH] (IRQs 3 4 5 *6 12)
[ 0.230513] Linux Plug and Play Support v0.97 © Adam Belay
[ 0.230546] pnp: PnP ACPI init
[ 0.230553] ACPI: bus type pnp registered
[ 0.233447] pnp: PnP ACPI: found 12 devices
[ 0.233450] ACPI: ACPI bus type pnp unregistered
[ 0.233454] PnPBIOS: Disabled by ACPI PNP
[ 0.233708] PCI: Using ACPI for IRQ routing
[ 0.233976] ACPI: RTC can wake from S4
[ 0.234003] system 00:05: ioport range 0x4d0-0x4d1 has been reserved
[ 0.234006] system 00:05: ioport range 0x40b-0x40b has been reserved
[ 0.234009] system 00:05: ioport range 0x4d6-0x4d6 has been reserved
[ 0.234012] system 00:05: ioport range 0xc00-0xc01 has been reserved
[ 0.234015] system 00:05: ioport range 0xc14-0xc14 has been reserved
[ 0.234018] system 00:05: ioport range 0xc50-0xc51 has been reserved
[ 0.234021] system 00:05: ioport range 0xc52-0xc52 has been reserved
[ 0.234023] system 00:05: ioport range 0xc6c-0xc6c has been reserved
[ 0.234026] system 00:05: ioport range 0xc6f-0xc6f has been reserved
[ 0.234029] system 00:05: ioport range 0xcd0-0xcd1 has been reserved
[ 0.234032] system 00:05: ioport range 0xcd2-0xcd3 has been reserved
[ 0.234035] system 00:05: ioport range 0xcd4-0xcd5 has been reserved
[ 0.234038] system 00:05: ioport range 0xcd6-0xcd7 has been reserved
[ 0.234040] system 00:05: ioport range 0xcd8-0xcdf has been reserved
[ 0.234043] system 00:05: ioport range 0x800-0x89f has been reserved
[ 0.234046] system 00:05: ioport range 0xb00-0xb1f could not be reserved
[ 0.234049] system 00:05: ioport range 0x900-0x90f has been reserved
[ 0.234053] system 00:05: ioport range 0x910-0x91f has been reserved
[ 0.234056] system 00:05: ioport range 0xfe00-0xfefe has been reserved
[ 0.234059] system 00:05: ioport range 0x4000-0x40fe has been reserved
[ 0.234063] system 00:05: iomem range 0xfed20000-0xfed3ffff has been reserved
[ 0.234066] system 00:05: iomem range 0xfed45000-0xfed89fff has been reserved
[ 0.234069] system 00:05: iomem range 0xffb80000-0xffbfffff could not be reserved
[ 0.234072] system 00:05: iomem range 0xfff80000-0xffffffff could not be reserved
[ 0.234082] system 00:08: iomem range 0xfec00000-0xfec00fff has been reserved
[ 0.234085] system 00:08: iomem range 0xfee00000-0xfee00fff could not be reserved
[ 0.234091] system 00:09: ioport range 0x25c-0x25c has been reserved
[ 0.234094] system 00:09: ioport range 0x25d-0x25d has been reserved
[ 0.234097] system 00:09: ioport range 0x25e-0x25e has been reserved
[ 0.234099] system 00:09: ioport range 0x25f-0x25f has been reserved
[ 0.234106] system 00:0a: iomem range 0xe0000000-0xefffffff has been reserved
[ 0.234112] system 00:0b: iomem range 0x0-0x9ffff could not be reserved
[ 0.234115] system 00:0b: iomem range 0xc0000-0xcffff could not be reserved
[ 0.234118] system 00:0b: iomem range 0xe0000-0xfffff could not be reserved
[ 0.234121] system 00:0b: iomem range 0x100000-0x1bffffff could not be reserved
[ 0.264507] PCI: Bridge: 0000:00:01.0
[ 0.264511] IO window: 7000-7fff
[ 0.264515] MEM window: 0xf8900000-0xf89fffff
[ 0.264519] PREFETCH window: 0x000000009ff00000-0x00000000afefffff
[ 0.264524] PCI: Bridge: 0000:00:04.0
[ 0.264526] IO window: disabled.
[ 0.264530] MEM window: disabled.
[ 0.264533] PREFETCH window: disabled.
[ 0.264537] PCI: Bridge: 0000:00:05.0
[ 0.264540] IO window: 8000-9fff
[ 0.264544] MEM window: 0xf8a00000-0xfc9fffff
[ 0.264548] PREFETCH window: 0x00000000aff00000-0x00000000cfefffff
[ 0.264553] PCI: Bridge: 0000:00:06.0
[ 0.264554] IO window: disabled.
[ 0.264558] MEM window: disabled.
[ 0.264561] PREFETCH window: disabled.
[ 0.264566] PCI: Bridge: 0000:00:07.0
[ 0.264567] IO window: disabled.
[ 0.264571] MEM window: disabled.
[ 0.264574] PREFETCH window: disabled.
[ 0.264588] PCI: Bus 9, cardbus bridge: 0000:08:01.0
[ 0.264590] IO window: 0x0000a000-0x0000a0ff
[ 0.264596] IO window: 0x0000a400-0x0000a4ff
[ 0.264602] PREFETCH window: 0xd0000000-0xd3ffffff
[ 0.264608] MEM window: 0x20000000-0x23ffffff
[ 0.264614] PCI: Bridge: 0000:00:14.4
[ 0.264618] IO window: a000-bfff
[ 0.264625] MEM window: 0xfca00000-0xfeafffff
[ 0.264631] PREFETCH window: 0x00000000cff00000-0x00000000dfefffff
[ 0.264660] PCI: Setting latency timer of device 0000:00:04.0 to 64
[ 0.264672] PCI: Setting latency timer of device 0000:00:05.0 to 64
[ 0.264684] PCI: Setting latency timer of device 0000:00:06.0 to 64
[ 0.264696] PCI: Setting latency timer of device 0000:00:07.0 to 64
[ 0.264728] ACPI: PCI Interrupt 0000:08:01.0[A] -> GSI 21 (level, low) -> IRQ 21
[ 0.264756] NET: Registered protocol family 2
[ 0.264855] IP route cache hash table entries: 4096 (order: 2, 16384 bytes)
[ 0.265070] TCP established hash table entries: 16384 (order: 5, 131072 bytes)
[ 0.265231] TCP bind hash table entries: 16384 (order: 5, 131072 bytes)
[ 0.265353] TCP: Hash tables configured (established 16384 bind 16384)
[ 0.265356] TCP reno registered
[ 0.265428] NET: Registered protocol family 1
[ 0.265546] checking if image is initramfs... it is
[ 0.768059] Switched to high resolution mode on CPU 0
[ 1.013309] Freeing initrd memory: 7769k freed
[ 1.013594] Simple Boot Flag at 0xff set to 0x1
[ 1.014232] audit: initializing netlink socket (disabled)
[ 1.014265] type=2000 audit(1227805663.012:1): initialized
[ 1.014410] Total HugeTLB memory allocated, 0
[ 1.014493] VFS: Disk quotas dquot_6.5.1
[ 1.014527] Dquot-cache hash table entries: 1024 (order 0, 4096 bytes)
[ 1.014581] msgmni has been set to 880
[ 1.014701] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 253)
[ 1.014706] io scheduler noop registered
[ 1.014708] io scheduler anticipatory registered
[ 1.014710] io scheduler deadline registered
[ 1.014719] io scheduler cfq registered (default)
[ 1.014805] pci 0000:01:05.0: Boot video device
[ 1.014934] PCI: Setting latency timer of device 0000:00:04.0 to 64
[ 1.014975] assign_interrupt_mode Found MSI capability
[ 1.015017] Allocate Port Service[0000:00:04.0:pcie00]
[ 1.015109] PCI: Setting latency timer of device 0000:00:05.0 to 64
[ 1.015146] assign_interrupt_mode Found MSI capability
[ 1.015181] Allocate Port Service[0000:00:05.0:pcie00]
[ 1.015219] Allocate Port Service[0000:00:05.0:pcie02]
[ 1.015311] PCI: Setting latency timer of device 0000:00:06.0 to 64
[ 1.015348] assign_interrupt_mode Found MSI capability
[ 1.015383] Allocate Port Service[0000:00:06.0:pcie00]
[ 1.015470] PCI: Setting latency timer of device 0000:00:07.0 to 64
[ 1.015507] assign_interrupt_mode Found MSI capability
[ 1.015543] Allocate Port Service[0000:00:07.0:pcie00]
[ 1.015867] isapnp: Scanning for PnP cards...
[ 1.370454] isapnp: No Plug & Play device found
[ 1.372997] Serial: 8250/16550 driver $Revision: 1.90 $ 4 ports, IRQ sharing enabled
[ 1.374786] brd: module loaded
[ 1.374880] PNP: PS/2 Controller [PNP0303:PS2K,PNP0f03:PS2M] at 0x60,0x64 irq 1,12
[ 1.377557] i8042.c: Detected active multiplexing controller, rev 1.1.
[ 1.378369] serio: i8042 KBD port at 0x60,0x64 irq 1
[ 1.378375] serio: i8042 AUX0 port at 0x60,0x64 irq 12
[ 1.378378] serio: i8042 AUX1 port at 0x60,0x64 irq 12
[ 1.378381] serio: i8042 AUX2 port at 0x60,0x64 irq 12
[ 1.378384] serio: i8042 AUX3 port at 0x60,0x64 irq 12
[ 1.378525] mice: PS/2 mouse device common for all mice
[ 1.378748] rtc_cmos 00:02: rtc core: registered rtc_cmos as rtc0
[ 1.378770] rtc0: alarms up to one month, y3k
[ 1.378804] cpuidle: using governor ladder
[ 1.378806] cpuidle: using governor menu
[ 1.378812] No iBFT detected.
[ 1.379244] TCP cubic registered
[ 1.379248] NET: Registered protocol family 17
[ 1.379256] Using IPI No-Shortcut mode
[ 1.379365] registered taskstats version 1
[ 1.379542] rtc_cmos 00:02: setting system clock to 2008-11-27 17:07:43 UTC (1227805663)
[ 1.379762] Freeing unused kernel memory: 244k freed
[ 1.506911] ACPI: CPU0 (power states: C1[C1] C2[C2])
[ 1.506958] ACPI: ACPI0007:00 is registered as cooling_device0
[ 1.506962] ACPI: Processor [CPU1] (supports 8 throttling states)
[ 1.508613] ACPI: EC: non-query interrupt received, switching to interrupt mode
[ 1.510113] Marking TSC unstable due to: TSC halts in idle.
[ 1.520227] input: AT Translated Set 2 keyboard as /class/input/input0
[ 1.679163] ACPI: LNXTHERM:01 is registered as thermal_zone0
[ 1.681593] ACPI: Thermal Zone [THRM] (53 C)
[ 2.292230] No dock devices found.
[ 2.328364] SCSI subsystem initialized
[ 2.360292] libata version 3.00 loaded.
[ 2.366675] ahci 0000:00:12.0: version 3.0
[ 2.366714] ACPI: PCI Interrupt 0000:00:12.0[A] -> GSI 22 (level, low) -> IRQ 22
[ 2.366741] ahci 0000:00:12.0: controller can't do 64bit DMA, forcing 32bit
[ 2.373701] usbcore: registered new interface driver usbfs
[ 2.373735] usbcore: registered new interface driver hub
[ 2.373787] usbcore: registered new device driver usb
[ 2.374983] ohci_hcd: 2006 August 04 USB 1.1 'Open' Host Controller (OHCI) Driver
[ 2.501587] sdhci: Secure Digital Host Controller Interface driver
[ 2.501590] sdhci: Copyright© Pierre Ossman
[ 2.537246] 8139too Fast Ethernet driver 0.9.28
[ 3.368089] ahci 0000:00:12.0: AHCI 0001.0100 32 slots 4 ports 3 Gbps 0xf impl SATA mode
[ 3.368094] ahci 0000:00:12.0: flags: ncq sntf ilck led clo pmp pio
[ 3.368434] scsi0 : ahci
[ 3.368567] scsi1 : ahci
[ 3.368631] scsi2 : ahci
[ 3.368698] scsi3 : ahci
[ 3.368787] ata1: SATA max UDMA/133 abar m1024@0xfebffc00 port 0xfebffd00 irq 22
[ 3.368791] ata2: SATA max UDMA/133 abar m1024@0xfebffc00 port 0xfebffd80 irq 22
[ 3.368795] ata3: SATA max UDMA/133 abar m1024@0xfebffc00 port 0xfebffe00 irq 22
[ 3.368799] ata4: SATA max UDMA/133 abar m1024@0xfebffc00 port 0xfebffe80 irq 22
[ 3.852044] ata1: softreset failed (device not ready)
[ 3.852099] ata1: failed due to HW bug, retry pmp=0
[ 4.016054] ata1: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
[ 4.016956] ata1.00: ATA-7: Hitachi HTS541680J9SA00, SB2OC70P, max UDMA/100
[ 4.016960] ata1.00: 156301488 sectors, multi 0: LBA48 NCQ (depth 31/32)
[ 4.016973] ata1.00: SB600 AHCI: limiting to 255 sectors per cmd
[ 4.018060] ata1.00: SB600 AHCI: limiting to 255 sectors per cmd
[ 4.018063] ata1.00: configured for UDMA/100
[ 4.336063] ata2: SATA link down (SStatus 0 SControl 300)
[ 4.656063] ata3: SATA link down (SStatus 0 SControl 300)
[ 4.976061] ata4: SATA link down (SStatus 0 SControl 300)
[ 4.976209] scsi 0:0:0:0: Direct-Access ATA Hitachi HTS54168 SB2O PQ: 0 ANSI: 5
[ 4.976654] ACPI: PCI Interrupt 0000:00:13.0[A] -> GSI 16 (level, low) -> IRQ 16
[ 4.976681] ohci_hcd 0000:00:13.0: OHCI Host Controller
[ 4.976876] ohci_hcd 0000:00:13.0: new USB bus registered, assigned bus number 1
[ 4.976904] ohci_hcd 0000:00:13.0: irq 16, io mem 0xfebfe000
[ 5.036140] usb usb1: configuration #1 chosen from 1 choice
[ 5.036174] hub 1-0:1.0: USB hub found
[ 5.036189] hub 1-0:1.0: 2 ports detected
[ 5.140140] usb usb1: New USB device found, idVendor=1d6b, idProduct=0001
[ 5.140143] usb usb1: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[ 5.140146] usb usb1: Product: OHCI Host Controller
[ 5.140148] usb usb1: Manufacturer: Linux 2.6.26-1-686 ohci_hcd
[ 5.140150] usb usb1: SerialNumber: 0000:00:13.0
[ 5.140222] ACPI: PCI Interrupt 0000:00:13.1[B] -> GSI 17 (level, low) -> IRQ 17
[ 5.140237] ohci_hcd 0000:00:13.1: OHCI Host Controller
[ 5.140265] ohci_hcd 0000:00:13.1: new USB bus registered, assigned bus number 2
[ 5.140286] ohci_hcd 0000:00:13.1: irq 17, io mem 0xfebfd000
[ 5.200152] usb usb2: configuration #1 chosen from 1 choice
[ 5.200182] hub 2-0:1.0: USB hub found
[ 5.200193] hub 2-0:1.0: 2 ports detected
[ 5.304132] usb usb2: New USB device found, idVendor=1d6b, idProduct=0001
[ 5.304136] usb usb2: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[ 5.304139] usb usb2: Product: OHCI Host Controller
[ 5.304141] usb usb2: Manufacturer: Linux 2.6.26-1-686 ohci_hcd
[ 5.304143] usb usb2: SerialNumber: 0000:00:13.1
[ 5.304226] ACPI: PCI Interrupt 0000:00:13.2[C] -> GSI 18 (level, low) -> IRQ 18
[ 5.304247] ohci_hcd 0000:00:13.2: OHCI Host Controller
[ 5.304271] ohci_hcd 0000:00:13.2: new USB bus registered, assigned bus number 3
[ 5.304292] ohci_hcd 0000:00:13.2: irq 18, io mem 0xfebfc000
[ 5.364142] usb usb3: configuration #1 chosen from 1 choice
[ 5.364170] hub 3-0:1.0: USB hub found
[ 5.364183] hub 3-0:1.0: 2 ports detected
[ 5.468123] usb usb3: New USB device found, idVendor=1d6b, idProduct=0001
[ 5.468127] usb usb3: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[ 5.468129] usb usb3: Product: OHCI Host Controller
[ 5.468131] usb usb3: Manufacturer: Linux 2.6.26-1-686 ohci_hcd
[ 5.468134] usb usb3: SerialNumber: 0000:00:13.2
[ 5.468201] ACPI: PCI Interrupt 0000:00:13.3[B] -> GSI 17 (level, low) -> IRQ 17
[ 5.468213] ohci_hcd 0000:00:13.3: OHCI Host Controller
[ 5.468235] ohci_hcd 0000:00:13.3: new USB bus registered, assigned bus number 4
[ 5.468251] ohci_hcd 0000:00:13.3: irq 17, io mem 0xfebfb000
[ 5.528123] usb usb4: configuration #1 chosen from 1 choice
[ 5.528155] hub 4-0:1.0: USB hub found
[ 5.528166] hub 4-0:1.0: 2 ports detected
[ 5.632124] usb usb4: New USB device found, idVendor=1d6b, idProduct=0001
[ 5.632127] usb usb4: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[ 5.632130] usb usb4: Product: OHCI Host Controller
[ 5.632132] usb usb4: Manufacturer: Linux 2.6.26-1-686 ohci_hcd
[ 5.632134] usb usb4: SerialNumber: 0000:00:13.3
[ 5.633226] ACPI: PCI Interrupt 0000:00:13.4[C] -> GSI 18 (level, low) -> IRQ 18
[ 5.633241] ohci_hcd 0000:00:13.4: OHCI Host Controller
[ 5.633271] ohci_hcd 0000:00:13.4: new USB bus registered, assigned bus number 5
[ 5.633286] ohci_hcd 0000:00:13.4: irq 18, io mem 0xfebfa000
[ 5.654470] Driver 'sd' needs updating - please use bus_type methods
[ 5.654589] sd 0:0:0:0: [sda] 156301488 512-byte hardware sectors (80026 MB)
[ 5.654615] sd 0:0:0:0: [sda] Write Protect is off
[ 5.654618] sd 0:0:0:0: [sda] Mode Sense: 00 3a 00 00
[ 5.654663] sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[ 5.654740] sd 0:0:0:0: [sda] 156301488 512-byte hardware sectors (80026 MB)
[ 5.654765] sd 0:0:0:0: [sda] Write Protect is off
[ 5.654768] sd 0:0:0:0: [sda] Mode Sense: 00 3a 00 00
[ 5.654813] sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[ 5.654819] sda:<6>usb usb5: configuration #1 chosen from 1 choice
[ 5.692185] hub 5-0:1.0: USB hub found
[ 5.692196] hub 5-0:1.0: 2 ports detected
[ 5.796131] usb usb5: New USB device found, idVendor=1d6b, idProduct=0001
[ 5.796135] usb usb5: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[ 5.796137] usb usb5: Product: OHCI Host Controller
[ 5.796140] usb usb5: Manufacturer: Linux 2.6.26-1-686 ohci_hcd
[ 5.796142] usb usb5: SerialNumber: 0000:00:13.4
[ 5.796237] ACPI: PCI Interrupt 0000:00:13.5[D] -> GSI 19 (level, low) -> IRQ 19
[ 5.796260] ehci_hcd 0000:00:13.5: EHCI Host Controller
[ 5.796288] ehci_hcd 0000:00:13.5: new USB bus registered, assigned bus number 6
[ 5.796329] ehci_hcd 0000:00:13.5: debug port 1
[ 5.796346] ehci_hcd 0000:00:13.5: irq 19, io mem 0xfebff800
[ 6.052568] sda1 sda2 < sda5 > sda3
[ 6.075633] sd 0:0:0:0: [sda] Attached SCSI disk
[ 8.848047] hub 4-0:1.0: Cannot enable port 1. Maybe the USB cable is bad?
[ 8.860048] ehci_hcd 0000:00:13.5: USB 2.0 started, EHCI 1.00, driver 10 Dec 2004
[ 8.860155] usb usb6: configuration #1 chosen from 1 choice
[ 8.860188] hub 6-0:1.0: USB hub found
[ 8.860197] hub 6-0:1.0: 10 ports detected
[ 8.916048] hub 4-0:1.0: unable to enumerate USB device on port 1
[ 8.964130] usb usb6: New USB device found, idVendor=1d6b, idProduct=0002
[ 8.964133] usb usb6: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[ 8.964136] usb usb6: Product: EHCI Host Controller
[ 8.964138] usb usb6: Manufacturer: Linux 2.6.26-1-686 ehci_hcd
[ 8.964140] usb usb6: SerialNumber: 0000:00:13.5
[ 8.972923] sdhci: SDHCI controller found at 0000:08:01.1 [1180:0822] (rev 17)
[ 8.972955] ACPI: PCI Interrupt 0000:08:01.1[C] -> GSI 23 (level, low) -> IRQ 23
[ 8.973975] mmc0: Will use DMA mode even though HW doesn't fully claim to support it.
[ 8.976033] mmc0: SDHCI at 0xfeaffc00 irq 23 DMA
[ 8.985085] ACPI: PCI Interrupt 0000:08:07.0[A] -> GSI 20 (level, low) -> IRQ 20
[ 8.988266] eth0: RealTek RTL8139 at 0xb800, 00:1b:fc:05:61:e1, IRQ 20
[ 8.988269] eth0: Identified 8139 chip type 'RTL-8100B/8139D'
[ 9.002447] Uniform Multi-Platform E-IDE driver
[ 9.002450] ide: Assuming 33MHz system bus speed for PIO modes; override with idebus=xx
[ 9.009444] 8139cp: 10/100 PCI Ethernet driver v1.3 (Mar 22, 2004)
[ 9.014301] SB600_PATA: IDE controller (0x1002:0x438c rev 0x00) at PCI slot 0000:00:14.1
[ 9.014313] ACPI: PCI Interrupt 0000:00:14.1[A] -> GSI 16 (level, low) -> IRQ 16
[ 9.014325] SB600_PATA: not 100% native mode: will probe irqs later
[ 9.014336] ide0: BM-DMA at 0xff00-0xff07
[ 9.014343] Probing IDE interface ide0...
[ 10.026433] hdb: MATSHITADVD-RAM UJ-850S, ATAPI CD/DVD-ROM drive
[ 10.080092] hdb: host max PIO4 wanted PIO255(auto-tune) selected PIO4
[ 10.080418] hdb: UDMA/33 mode selected
[ 10.080833] ide0 at 0x1f0-0x1f7,0x3f6 on irq 14
[ 10.105366] hdb: ATAPI 24X DVD-ROM DVD-R-RAM CD-R/RW drive, 2048kB Cache
[ 10.105374] Uniform CD-ROM driver Revision: 3.20
[ 10.212583] PM: Starting manual resume from disk
[ 10.267060] kjournald starting. Commit interval 5 seconds
[ 10.267072] EXT3-fs: mounted filesystem with ordered data mode.
[ 12.544049] hub 4-0:1.0: Cannot enable port 1. Maybe the USB cable is bad?
[ 13.328017] udevd version 125 started
[ 14.419628] Linux agpgart interface v0.103
[ 14.463177] pci_hotplug: PCI Hot Plug PCI Core version: 0.5
[ 14.520573] shpchp: Standard Hot Plug PCI Controller Driver version: 0.4
[ 14.548569] input: Power Button (FF) as /class/input/input1
[ 14.576074] ACPI: Power Button (FF) [PWRF]
[ 14.576165] input: Lid Switch as /class/input/input2
[ 14.588048] hub 4-0:1.0: unable to enumerate USB device on port 1
[ 14.593752] ACPI: Lid Switch [LID]
[ 14.593832] input: Power Button (CM) as /class/input/input3
[ 14.612087] ACPI: Power Button (CM) [PWRB]
[ 14.612108] Asus Laptop ACPI Extras version 0.30
[ 14.616721] BSTS called, 0x22 returned
[ 14.616725] unsupported model X51R, trying default values
[ 14.616727] send /proc/acpi/dsdt to the developers
[ 14.616799] input: Sleep Button (CM) as /class/input/input4
[ 14.644091] ACPI: Sleep Button (CM) [SLPB]
[ 14.865184] ACPI: AC Adapter [AC0] (on-line)
[ 15.233282] ACPI: Battery Slot [BAT0] (battery present)
[ 15.242385] ACPI: device:04 is registered as cooling_device1
[ 15.242513] input: Video Bus as /class/input/input5
[ 15.272074] ACPI: Video Device [VGA] (multi-head: yes rom: no post: no)
[ 15.615554] piix4_smbus 0000:00:14.0: Found 0000:00:14.0 device
[ 16.111527] input: PC Speaker as /class/input/input6
[ 16.339542] Yenta: CardBus bridge found at 0000:08:01.0 [1043:1627]
[ 16.435069] ACPI: PCI Interrupt 0000:00:14.2[A] -> GSI 16 (level, low) -> IRQ 16
[ 16.468633] Yenta: ISA IRQ mask 0x0cb8, PCI irq 21
[ 16.468637] Socket status: 30000006
[ 16.468641] Yenta: Raising subordinate bus# of parent bus (#08) from #09 to #0c
[ 16.468647] pcmcia: parent PCI bridge I/O window: 0xa000 - 0xbfff
[ 16.468651] cs: IO port probe 0xa000-0xbfff: clean.
[ 16.469183] pcmcia: parent PCI bridge Memory window: 0xfca00000 - 0xfeafffff
[ 16.469186] pcmcia: parent PCI bridge Memory window: 0xcff00000 - 0xdfefffff
[ 16.744858] Synaptics Touchpad, model: 1, fw: 6.1, id: 0xa3a0b3, caps: 0xa04713/0x10008
[ 16.784163] input: SynPS/2 Synaptics TouchPad as /class/input/input7
[ 17.312714] cs: IO port probe 0x100-0x3af: clean.
[ 17.312714] cs: IO port probe 0x3e0-0x4ff: clean.
[ 17.316345] cs: IO port probe 0x820-0x8ff: clean.
[ 17.316702] cs: IO port probe 0xc00-0xcf7: clean.
[ 17.317467] cs: IO port probe 0xa00-0xaff: clean.
[ 18.368145] Adding 1004020k swap on /dev/sda5. Priority:-1 extents:1 across:1004020k
[ 18.848781] EXT3 FS on sda1, internal journal
[ 19.116976] loop: module loaded
[ 19.234640] nf_conntrack version 0.5.0 (7168 buckets, 28672 max)
[ 19.360592] NTFS driver 2.1.29 [Flags: R/W MODULE].
[ 19.479336] ACPI: PCI Interrupt 0000:01:05.0[A] -> GSI 17 (level, low) -> IRQ 17
[ 19.479336] radeonfb: Retrieved PLL infos from BIOS
[ 19.479336] radeonfb: Reference=14.32 MHz (RefDiv=6) Memory=330.00 Mhz, System=333.00 MHz
[ 19.479336] radeonfb: PLL min 20000 max 40000
[ 20.080045] Non-DDC laptop panel detected
[ 20.177083] i2c-adapter i2c-3: unable to read EDID block.
[ 20.329080] i2c-adapter i2c-3: unable to read EDID block.
[ 20.481080] i2c-adapter i2c-3: unable to read EDID block.
[ 20.837043] radeonfb: Monitor 1 type LCD found
[ 20.837047] radeonfb: Monitor 2 type no found
[ 20.837051] radeonfb: panel ID string: CMO
[ 20.837054] radeonfb: detected LVDS panel size from BIOS: 1280x800
[ 20.837056] radeondb: BIOS provided dividers will be used
[ 20.916044] radeonfb: Dynamic Clock Power Management enabled
[ 20.916609] Console: switching to colour frame buffer device 160x50
[ 20.930795] radeonfb (0000:01:05.0): ATI Radeon 5a62 "Zb"
[ 21.063362] usbcore: registered new interface driver usblp
[ 21.144215] usbcore: registered new interface driver cdc_acm
[ 21.144215] cdc_acm: v0.26:USB Abstract Control Model driver for USB modems and ISDN adapters
[ 21.196475] usbcore: registered new interface driver usbserial
[ 21.196489] usbserial: USB Serial support registered for generic
[ 21.196505] usbcore: registered new interface driver usbserial_generic
[ 21.196507] usbserial: USB Serial Driver core
[ 21.235662] NET: Registered protocol family 8
[ 21.235662] NET: Registered protocol family 20
[ 21.508715] QEMU Accelerator Module version 1.3.0, Copyright © 2005-2007 Fabrice Bellard
[ 21.508715] KQEMU installed, max_locked_mem=225464kB.
[ 21.609152] ip_tables: © 2000-2006 Netfilter Core Team
[ 21.996185] usbcore: registered new interface driver hiddev
[ 21.996202] usbcore: registered new interface driver usbhid
[ 21.996204] usbhid: v2.6:USB HID core driver
[ 22.107409] device-mapper: uevent: version 1.0.3
[ 22.112943] device-mapper: ioctl: 4.13.0-ioctl (2007-10-18) initialised: dm-devel@redhat.com
[ 22.465949] kjournald starting. Commit interval 5 seconds
[ 22.466105] EXT3 FS on sda3, internal journal
[ 22.466105] EXT3-fs: mounted filesystem with ordered data mode.
[ 24.112443] eth0: link up, 100Mbps, full-duplex, lpa 0x41E1
[ 25.692064] hub 3-0:1.0: unable to enumerate USB device on port 1
[ 28.642157] NET: Registered protocol family 10
[ 28.642639] lo: Disabled Privacy Extensions
[ 29.276045] hub 3-0:1.0: Cannot enable port 1. Maybe the USB cable is bad?
[ 32.364056] hub 3-0:1.0: Cannot enable port 1. Maybe the USB cable is bad?
[ 32.444070] hub 3-0:1.0: unable to enumerate USB device on port 1
[ 35.131953] Bluetooth: Core ver 2.11
[ 35.132010] NET: Registered protocol family 31
[ 35.132010] Bluetooth: HCI device and connection manager initialized
[ 35.132010] Bluetooth: HCI socket layer initialized
[ 35.155867] Bluetooth: L2CAP ver 2.9
[ 35.155873] Bluetooth: L2CAP socket layer initialized
[ 35.275301] Bluetooth: RFCOMM socket layer initialized
[ 35.275319] Bluetooth: RFCOMM TTY layer initialized
[ 35.275321] Bluetooth: RFCOMM ver 1.8
[ 39.612020] eth0: no IPv6 routers present
[ 39.728044] hub 3-0:1.0: unable to enumerate USB device on port 2
[ 39.855698] [drm] Initialized drm 1.1.0 20060810
[ 39.863739] [drm] Initialized radeon 1.29.0 20080528 on minor 0
[ 40.315748] [drm] Setting GART location based on new memory map
[ 40.315748] [drm] Loading R300 Microcode
[ 40.315748] [drm] Num pipes: 1
[ 40.315748] [drm] writeback test succeeded in 1 usecs
[ 43.364047] hub 3-0:1.0: Cannot enable port 2. Maybe the USB cable is bad?
[ 46.452053] hub 3-0:1.0: Cannot enable port 2. Maybe the USB cable is bad?
[ 48.194944] [drm] Num pipes: 1
[ 49.540046] hub 3-0:1.0: Cannot enable port 2. Maybe the USB cable is bad?
[ 52.628054] hub 3-0:1.0: Cannot enable port 2. Maybe the USB cable is bad?
[ 52.628998] hub 3-0:1.0: unable to enumerate USB device on port 2
[ 72.528048] hub 4-0:1.0: unable to enumerate USB device on port 1
[ 76.112049] hub 4-0:1.0: Cannot enable port 1. Maybe the USB cable is bad?
[ 79.200051] hub 4-0:1.0: Cannot enable port 1. Maybe the USB cable is bad?
[ 80.380055] hub 4-0:1.0: unable to enumerate USB device on port 1
[ 82.388043] usb 1-1: new low speed USB device using ohci_hcd and address 2
[ 82.528040] usb 1-1: device descriptor read/64, error -62
[ 82.692049] hub 1-0:1.0: unable to enumerate USB device on port 1
[ 83.324048] usb 1-1: new low speed USB device using ohci_hcd and address 3
[ 83.464041] usb 1-1: device descriptor read/64, error -62
[ 83.628062] hub 1-0:1.0: unable to enumerate USB device on port 1
[ 84.076048] hub 1-0:1.0: unable to enumerate USB device on port 1
[ 84.580042] usb 1-1: new low speed USB device using ohci_hcd and address 5
[ 84.640063] hub 1-0:1.0: unable to enumerate USB device on port 1
[ 85.088044] hub 1-0:1.0: unable to enumerate USB device on port 1
[ 85.592045] usb 1-1: new low speed USB device using ohci_hcd and address 7
[ 85.732044] usb 1-1: device descriptor read/64, error -62
[ 85.896051] hub 1-0:1.0: unable to enumerate USB device on port 1
[ 86.400044] usb 1-1: new low speed USB device using ohci_hcd and address 8
[ 86.460069] hub 1-0:1.0: unable to enumerate USB device on port 1
[ 86.908046] hub 1-0:1.0: unable to enumerate USB device on port 1
[ 87.412042] usb 1-1: new low speed USB device using ohci_hcd and address 10
[ 87.552042] usb 1-1: device descriptor read/64, error -62
[ 87.716053] hub 1-0:1.0: unable to enumerate USB device on port 1
[ 88.164053] hub 1-0:1.0: unable to enumerate USB device on port 1
[ 88.668046] usb 1-1: new low speed USB device using ohci_hcd and address 12
[ 88.808040] usb 1-1: device descriptor read/64, error -62
[ 89.052042] usb 1-1: device descriptor read/64, error -62
[ 89.236050] hub 1-0:1.0: unable to enumerate USB device on port 1
[ 140.256044] usb 1-1: new low speed USB device using ohci_hcd and address 14
[ 140.424864] usb 1-1: configuration #1 chosen from 1 choice
[ 140.440316] input: Genius NetScroll + Traveler as /class/input/input8
[ 140.468094] input,hidraw0: USB HID v1.10 Mouse [Genius NetScroll + Traveler] on usb-0000:00:13.0-1
[ 140.468201] usb 1-1: New USB device found, idVendor=0458, idProduct=002e
[ 140.468204] usb 1-1: New USB device strings: Mfr=2, Product=1, SerialNumber=0
[ 140.468207] usb 1-1: Product: NetScroll + Traveler
[ 140.468209] usb 1-1: Manufacturer: Genius
[ 145.711230] [drm] Loading R300 Microcode
[ 145.711230] [drm] Num pipes: 1
[ 538.576220] usb 1-1: USB disconnect, address 14
[ 548.560452] hub 4-0:1.0: unable to enumerate USB device on port 1
[ 552.016053] hub 4-0:1.0: Cannot enable port 1. Maybe the USB cable is bad?
[ 555.104060] hub 4-0:1.0: Cannot enable port 1. Maybe the USB cable is bad?
[ 558.192427] hub 4-0:1.0: Cannot enable port 1. Maybe the USB cable is bad?
[ 561.284064] hub 4-0:1.0: Cannot enable port 1. Maybe the USB cable is bad?
[ 561.284082] hub 4-0:1.0: unable to enumerate USB device on port 1
[ 795.164061] hub 4-0:1.0: Cannot enable port 1. Maybe the USB cable is bad?
[ 798.252058] hub 4-0:1.0: Cannot enable port 1. Maybe the USB cable is bad?
[ 801.340054] hub 4-0:1.0: Cannot enable port 1. Maybe the USB cable is bad?
[ 804.428061] hub 4-0:1.0: Cannot enable port 1. Maybe the USB cable is bad?
[ 804.428077] hub 4-0:1.0: unable to enumerate USB device on port 1Периодами выдает еще такое сообщение:
Код: Выделить всё
[ 1209.140079] hub 1-0:1.0: unable to enumerate USB device on port 1
[ 1209.772059] usb 1-1: new low speed USB device using ohci_hcd and address 16
[ 1209.912060] usb 1-1: device descriptor read/64, error -62
[ 1210.156066] usb 1-1: device descriptor read/64, error -62
[ 1210.396052] usb 1-1: new low speed USB device using ohci_hcd and address 17
[ 1210.456077] hub 1-0:1.0: unable to enumerate USB device on port 1
[ 1210.904074] hub 1-0:1.0: unable to enumerate USB device on port 1При подключении на любой из портов пишет одно и тоже. Светодиод светиться. В винде мышь работает нормально. Почитал по инету, собственно нашел пару коментариев что это недоработка в ядре какая-то. Но инфы по этому вопросу мало.
П.С. Раньше стоял Debian Testing подключался 1 из нескольких десятков раз, все остальные выдавало ту же ошибку. Помогите плз.
