Решено:XF86Config - Ошибка: "Caught signal 11. Server aborting" (Проблема с запуском X-ов)

[HerrOberst]

Уже неделю пытаюсь на старый ноутбук (Сyrix 486 DX-2 66 Mhz) поставить Slackware 8.0. Но никак не получается запустить X-ы.
Конфиг уже весь, в ручную, по сотому кругу переписал (с различными вариациями) - ничего не получается.

Последнее чего добился - сервер вылетает после загрузки модуля RAMDAC:

Код: Выделить всё

(II) Loading sub module "ramdac"
(II) LoadModule: "ramdac"
(II) Loading /usr/X11R6/lib/modules/libramdac.a
(II) Module ramdac: vendor="The XFree86 Project"
    compiled for 4.1.0, module version = 0.1.0
    ABI class: XFree86 Video Driver, version 0.4
(II) do I need RAC?  No, I don't.
(II) resource ranges after preInit:
    [0] 0    0x01400000 - 0x01c00000 (0x800001) MX[B]
    [1] 0    0x000b8000 - 0x000bffff (0x8000) MX[B](OprD)
    [2] 0    0x000b0000 - 0x000b7fff (0x8000) MX[B](OprD)
    [3] 0    0x000a0000 - 0x000affff (0x10000) MX[B](OprD)
    [4] -1    0xffe00000 - 0xffffffff (0x200000) MX[B](B)
    [5] -1    0x00100000 - 0x3fffffff (0x3ff00000) MX[B]E(B)
    [6] -1    0x000f0000 - 0x000fffff (0x10000) MX[B]
    [7] -1    0x000c0000 - 0x000effff (0x30000) MX[B]
    [8] -1    0x00000000 - 0x0009ffff (0xa0000) MX[B]
    [9] 0    0x00000200 - 0x000083fc  IX[S]
    [10] 0    0x000003c0 - 0x000003df (0x20) IX[B]
    [11] 0    0x000003b0 - 0x000003bb (0xc) IX[B]
    [12] -1    0x0000ffff - 0x0000ffff (0x1) IX[B]
    [13] -1    0x00000000 - 0x000000ff (0x100) IX[B]

Fatal server error:
Caught signal 11.  Server aborting

Help me!!!

[flank'er]

http://slackware.mirrors.tds.net/pub/slack...are-8.1/FAQ.TXT

Q27: Why do my compiles sometimes die with 'signal 11: internal compiler error'?

A: This indicates a hardware problem in about 99% of the cases. It can usually
be fixed by increasing the number of wait states in the CMOS settings. It
can almost always be fixed by turning off the RAM cache, but this should be
your last resort since it will cause a noticeable slowdown.

Another common reason for this problem is heat, particularly in the case
of an overclocked CPU. I've had some machines suffer from this over
the years, especially under heavy load. If the signal 11 problem seems
more common when the machine's been running for a while, it could well be
heat-related. Try running the machine with the case open. If that doesn't
seem to help, aim a fan at the motherboard. (I've had to run machines
containing hot-running SCSI drives this way for their entire lives) A
quality CPU fan helps a lot, too. If you have an underpowered fan/heatsink,
consider a replacement from TennMax (www.TennMax.com). I've had excellent
results with their fans. (a dual-fan model stabilized my P2-450)

For more information on causes and cures of the signal 11 problem, see the
latest version of the Signal 11 FAQ at http://www.bitwizard.nl/sig11/

The French translation can be found at:
http://www.linux-france.com/article/sig11fr/

у меня signal 11 вылазил на i486DXOverDrive-66Mhz при сборки Perl'a(вроде).
посоветовать можно поставить другую сборку, десятую или одинадцатую slackware.
но imho на этой машинке стабильно можно работать только в консольном режиме.

[HerrOberst]

Спасибо flank'er. Проблема была похоже в сборке.
Установил Slackware 4.0 - X-сы запустились. (Потом попробую поставить что-нибудь поновее)