SanDisk SDWCFB-128 Connect Plus 128MB + Wi-Fi CompactFlash (Не работает, не знаю почему .....)

SANyaSmolenskii · Сообщение **SANyaSmolenskii** » 18.05.2009 22:38

Ноутбук Toshiba Satellite S503. Установлена MAndriva2009.1 . Нужно запустить на нем pcmcia wi-fi карту SanDisk. Карта однозначно работает, и на этом ноутбуке тоже, проверено в оффтопике. Настраивал первоначально графическим конфигуратором, но не вышло ничего.

При вставке в разъем карты в syslog валится следующее:

Код:

May 18 19:42:55 MadNoutV3 klogd: pcmcia_socket pcmcia_socket1: pccard: PCMCIA card inserted into slot 1
May 18 19:42:55 MadNoutV3 klogd: pcmcia_socket pcmcia_socket1: cs: memory probe 0xfce00000-0xfcefffff: excluding 0xfce00000-0xfce0ffff 0xfcee0000-0xfcefffff
May 18 19:42:55 MadNoutV3 klogd: pcmcia 1.0: pcmcia: registering new device pcmcia1.0
May 18 19:42:55 MadNoutV3 klogd: pcmcia 1.1: pcmcia: registering new device pcmcia1.1
May 18 19:42:55 MadNoutV3 klogd: lib80211: common routines for IEEE802.11 drivers
May 18 19:42:55 MadNoutV3 klogd: lib80211_crypt: registered algorithm 'NULL'
May 18 19:42:55 MadNoutV3 klogd: scsi2 : pata_pcmcia
May 18 19:42:55 MadNoutV3 klogd: ata3: PATA max PIO0 cmd 0xd100 ctl 0xd10e irq 3
May 18 19:42:55 MadNoutV3 klogd: ata3.00: CFA: SanDisk SDWCFB-128, Vdg 8.21, max PIO1
May 18 19:42:55 MadNoutV3 klogd: ata3.00: 250880 sectors, multi 0: LBA
May 18 19:42:55 MadNoutV3 klogd: ata3.00: configured for PIO0
May 18 19:42:55 MadNoutV3 klogd: ata3.00: configured for PIO0
May 18 19:42:55 MadNoutV3 klogd: ata3: EH complete
May 18 19:42:55 MadNoutV3 klogd: isa bounce pool size: 16 pages
May 18 19:42:55 MadNoutV3 klogd: scsi 2:0:0:0: Direct-Access     ATA      SanDisk SDWCFB-1 Vdg  PQ: 0 ANSI: 5
May 18 19:42:55 MadNoutV3 klogd: sd 2:0:0:0: [sdb] 250880 512-byte hardware sectors: (128 MB/122 MiB)
May 18 19:42:55 MadNoutV3 klogd: sd 2:0:0:0: [sdb] Write Protect is off
May 18 19:42:55 MadNoutV3 klogd: sd 2:0:0:0: [sdb] Mode Sense: 00 3a 00 00
May 18 19:42:55 MadNoutV3 klogd: sd 2:0:0:0: [sdb] Write cache: disabled, read cache: enabled, doesn't support DPO or FUA
May 18 19:42:55 MadNoutV3 klogd: sd 2:0:0:0: [sdb] 250880 512-byte hardware sectors: (128 MB/122 MiB)
May 18 19:42:55 MadNoutV3 klogd: sd 2:0:0:0: [sdb] Write Protect is off
May 18 19:42:55 MadNoutV3 klogd: sd 2:0:0:0: [sdb] Mode Sense: 00 3a 00 00
May 18 19:42:55 MadNoutV3 klogd: sd 2:0:0:0: [sdb] Write cache: disabled, read cache: enabled, doesn't support DPO or FUA
May 18 19:42:55 MadNoutV3 klogd:  sdb: sdb1
May 18 19:42:55 MadNoutV3 klogd: sd 2:0:0:0: [sdb] Attached SCSI removable disk
May 18 19:42:55 MadNoutV3 klogd: sd 2:0:0:0: Attached scsi generic sg2 type 0
May 18 19:42:55 MadNoutV3 klogd: hostap_cs: setting Vcc=33 (constant)
May 18 19:42:55 MadNoutV3 klogd: Checking CFTABLE_ENTRY 0x01 (default 0x01)
May 18 19:42:55 MadNoutV3 klogd: IO window settings: cfg->io.nwin=1 dflt->io.nwin=1
May 18 19:42:55 MadNoutV3 klogd: io->flags = 0x0047, io.base=0x0000, len=128
May 18 19:42:55 MadNoutV3 klogd: wifi0 (hostap_cs): not using net_device_ops yet
May 18 19:42:55 MadNoutV3 klogd: hostap_cs: Registered netdevice wifi0
May 18 19:42:55 MadNoutV3 klogd: hostap_cs 1.0: pcmcia: request for exclusive IRQ could not be fulfilled.
May 18 19:42:55 MadNoutV3 klogd: hostap_cs 1.0: pcmcia: the driver needs updating to supported shared IRQ lines.
May 18 19:42:55 MadNoutV3 klogd: hostap_cs: index 0x01: , irq 3, io 0xd180-0xd1ff
May 18 19:42:55 MadNoutV3 klogd: wifi0: Multi-function SanDisk ConnectPlus detected - using vendor-specific initialization
May 18 19:42:56 MadNoutV3 klogd: hostap_cs: assuming no Primary image in flash - card initialization not completed
May 18 19:42:56 MadNoutV3 klogd: wifi0: test Genesis mode with HCR 0x1f
May 18 19:42:56 MadNoutV3 klogd: prism2_pccard_cor_sreset: original COR 4b
May 18 19:42:56 MadNoutV3 klogd: prism2_interrupt: >20 events (EvStat=0x8af8)
May 18 19:42:56 MadNoutV3 klogd: Readback test failed, HCR 0x1f write 00 e1 a1 ff read 00 ce a1 ce
May 18 19:42:56 MadNoutV3 klogd: wifi0: test Genesis mode with HCR 0x0f
May 18 19:42:56 MadNoutV3 klogd: prism2_pccard_cor_sreset: original COR 4f
May 18 19:42:56 MadNoutV3 klogd: prism2_interrupt: >20 events (EvStat=0x8af8)
May 18 19:42:56 MadNoutV3 klogd: Readback test succeeded, HCR 0x0f
May 18 19:42:56 MadNoutV3 klogd: wlan0 (hostap_cs): not using net_device_ops yet
May 18 19:42:56 MadNoutV3 klogd: wifi0: registered netdevice wlan0
May 18 19:42:57 MadNoutV3 klogd: wlan0: cannot get RID fdc6 (len=12) - no PRI f/w
May 18 19:42:57 MadNoutV3 klogd: wlan0: cannot get RID fdc1 (len=2) - no PRI f/w
May 18 19:42:57 MadNoutV3 klogd: wlan0: cannot get RID fdc6 (len=12) - no PRI f/w
May 18 19:42:57 MadNoutV3 klogd: wlan0: cannot get RID fd42 (len=6) - no PRI f/w
May 18 19:42:57 MadNoutV3 klogd: wlan0: cannot get RID fc84 (len=2) - no PRI f/w
May 18 19:42:57 MadNoutV3 klogd: wlan0: cannot get RID fc09 (len=2) - no PRI f/w
May 18 19:42:57 MadNoutV3 klogd: wlan0: cannot get RID fc0e (len=34) - no PRI f/w
May 18 19:42:57 MadNoutV3 klogd: wlan0: cannot get RID fc06 (len=2) - no PRI f/w
May 18 19:42:57 MadNoutV3 klogd: wlan0: cannot get RID fd48 (len=2) - no PRI f/w
May 18 19:42:57 MadNoutV3 klogd: wlan0: cannot get RID fc83 (len=2) - no PRI f/w
May 18 19:42:57 MadNoutV3 klogd: wlan0: cannot get RID fc82 (len=2) - no PRI f/w
May 18 19:42:57 MadNoutV3 klogd: wifi0: cannot get RID fc28 (len=2) - no PRI f/w
May 18 19:42:57 MadNoutV3 klogd: Could not read current WEP flags.
May 18 19:42:57 MadNoutV3 klogd: wifi0: encryption setup failed
May 18 19:42:57 MadNoutV3 klogd: wlan0: set_encryption failed
May 18 19:42:57 MadNoutV3 klogd: wlan0: Host AP mode does not support 'Any' essid
May 18 19:42:57 MadNoutV3 klogd: prism2: wlan0: operating mode changed 3 -> 1
May 18 19:42:57 MadNoutV3 klogd: wlan0: cannot set RID fc00 (len=2) - no PRI f/w
May 18 19:42:57 MadNoutV3 klogd: wlan0: cannot set RID fc0e (len=34) - no PRI f/w
May 18 19:42:57 MadNoutV3 klogd: lib80211_crypt: registered algorithm 'WEP'
May 18 19:42:57 MadNoutV3 klogd: wifi0: cannot get RID fc28 (len=2) - no PRI f/w
May 18 19:42:57 MadNoutV3 klogd: Could not read current WEP flags.
May 18 19:42:57 MadNoutV3 klogd: wifi0: encryption setup failed
May 18 19:42:57 MadNoutV3 klogd: wlan0: set_encryption failed
May 18 19:42:57 MadNoutV3 klogd: wlan0: cannot set RID fc02 (len=34) - no PRI f/w
May 18 19:42:58 MadNoutV3 klogd: prism2: wlan0: operating mode changed 1 -> 2
May 18 19:42:58 MadNoutV3 klogd: wlan0: cannot set RID fc00 (len=2) - no PRI f/w
May 18 19:42:58 MadNoutV3 klogd: wlan0: cannot get RID fdc6 (len=12) - no PRI f/w
May 18 19:42:58 MadNoutV3 klogd: wifi0: cannot set RID fc2d (len=2) - no PRI f/w
May 18 19:42:58 MadNoutV3 klogd: wifi0: cannot get RID fc28 (len=2) - no PRI f/w
May 18 19:42:58 MadNoutV3 klogd: Could not read current WEP flags.
May 18 19:42:58 MadNoutV3 klogd: wifi0: encryption setup failed
May 18 19:42:58 MadNoutV3 klogd: wifi0: cannot get RID fc28 (len=2) - no PRI f/w
May 18 19:42:58 MadNoutV3 klogd: Could not read current WEP flags.
May 18 19:42:58 MadNoutV3 klogd: wifi0: encryption setup failed
May 18 19:42:58 MadNoutV3 klogd: wifi0: cannot get RID fc28 (len=2) - no PRI f/w
May 18 19:42:58 MadNoutV3 klogd: Could not read current WEP flags.
May 18 19:42:58 MadNoutV3 klogd: wifi0: encryption setup failed
May 18 19:42:58 MadNoutV3 klogd: wifi0: cannot get RID fc28 (len=2) - no PRI f/w
May 18 19:42:58 MadNoutV3 klogd: Could not read current WEP flags.
May 18 19:42:58 MadNoutV3 klogd: wifi0: encryption setup failed
May 18 19:42:58 MadNoutV3 ifplugd(wlan0)[4534]: ifplugd 0.28 initializing.
May 18 19:42:58 MadNoutV3 ifplugd(wlan0)[4534]: Using interface wlan0/00:00:00:00:00:00 with driver <hostap> (version: )
May 18 19:42:58 MadNoutV3 ifplugd(wlan0)[4534]: Using detection mode: IFF_RUNNING
May 18 19:42:58 MadNoutV3 ifplugd(wlan0)[4534]: Initialization complete, link beat not detected.
May 18 19:42:58 MadNoutV3 klogd: wlan0: cannot get RID fd42 (len=6) - no PRI f/w
May 18 19:42:58 MadNoutV3 klogd: wlan0: cannot get RID fdc6 (len=12) - no PRI f/w
May 18 19:43:27 MadNoutV3 klogd: ata3.00: exception Emask 0x0 SAct 0x0 SErr 0x0 action 0x6 frozen
May 18 19:43:27 MadNoutV3 klogd: ata3.00: cmd 20/00:20:00:00:00/00:00:00:00:00/e0 tag 0 pio 16384 in
May 18 19:43:27 MadNoutV3 klogd:          res 40/00:00:00:00:00/00:00:00:00:00/00 Emask 0x4 (timeout)
May 18 19:43:27 MadNoutV3 klogd: ata3.00: status: { DRDY }
May 18 19:43:27 MadNoutV3 klogd: ata3: soft resetting link
May 18 19:43:32 MadNoutV3 klogd: ata3.00: qc timeout (cmd 0x91)
May 18 19:43:32 MadNoutV3 klogd: ata3.00: failed to IDENTIFY (INIT_DEV_PARAMS failed, err_mask=0x4)
May 18 19:43:32 MadNoutV3 klogd: ata3.00: revalidation failed (errno=-5)
May 18 19:43:32 MadNoutV3 klogd: ata3: soft resetting link
May 18 19:43:42 MadNoutV3 klogd: ata3.00: qc timeout (cmd 0x91)
May 18 19:43:42 MadNoutV3 klogd: ata3.00: failed to IDENTIFY (INIT_DEV_PARAMS failed, err_mask=0x4)
May 18 19:43:42 MadNoutV3 klogd: ata3.00: revalidation failed (errno=-5)
May 18 19:43:42 MadNoutV3 klogd: ata3: soft resetting link
May 18 19:43:52 MadNoutV3 klogd: ata3.00: qc timeout (cmd 0x91)
May 18 19:43:52 MadNoutV3 klogd: ata3.00: failed to IDENTIFY (INIT_DEV_PARAMS failed, err_mask=0x4)
May 18 19:43:52 MadNoutV3 klogd: ata3.00: revalidation failed (errno=-5)
May 18 19:43:52 MadNoutV3 klogd: ata3.00: disabled
May 18 19:43:52 MadNoutV3 klogd: ata3: soft resetting link
May 18 19:43:52 MadNoutV3 klogd: ata3: EH complete
May 18 19:43:52 MadNoutV3 klogd: sd 2:0:0:0: [sdb] Unhandled error code
May 18 19:43:52 MadNoutV3 klogd: sd 2:0:0:0: [sdb] Result: hostbyte=DID_BAD_TARGET driverbyte=DRIVER_OK,SUGGEST_OK
May 18 19:43:52 MadNoutV3 klogd: end_request: I/O error, dev sdb, sector 0
May 18 19:43:52 MadNoutV3 klogd: Buffer I/O error on device sdb, logical block 0
May 18 19:43:52 MadNoutV3 klogd: Buffer I/O error on device sdb, logical block 1
May 18 19:43:52 MadNoutV3 klogd: Buffer I/O error on device sdb, logical block 2
May 18 19:43:52 MadNoutV3 klogd: Buffer I/O error on device sdb, logical block 3
May 18 19:43:52 MadNoutV3 klogd: sd 2:0:0:0: [sdb] Unhandled error code
May 18 19:43:52 MadNoutV3 klogd: sd 2:0:0:0: [sdb] Result: hostbyte=DID_BAD_TARGET driverbyte=DRIVER_OK,SUGGEST_OK
May 18 19:43:52 MadNoutV3 klogd: end_request: I/O error, dev sdb, sector 0
May 18 19:43:52 MadNoutV3 klogd: Buffer I/O error on device sdb, logical block 0
May 18 19:43:52 MadNoutV3 klogd: sd 2:0:0:0: [sdb] READ CAPACITY failed
May 18 19:43:52 MadNoutV3 klogd: sd 2:0:0:0: [sdb] Result: hostbyte=DID_BAD_TARGET driverbyte=DRIVER_OK,SUGGEST_OK
May 18 19:43:52 MadNoutV3 klogd: sd 2:0:0:0: [sdb] Sense not available.
May 18 19:43:52 MadNoutV3 klogd: sd 2:0:0:0: [sdb] Write Protect is off
May 18 19:43:52 MadNoutV3 klogd: sd 2:0:0:0: [sdb] Mode Sense: 00 00 00 00
May 18 19:43:52 MadNoutV3 klogd: sd 2:0:0:0: [sdb] Asking for cache data failed
May 18 19:43:52 MadNoutV3 klogd: sd 2:0:0:0: [sdb] Assuming drive cache: write through
May 18 19:43:52 MadNoutV3 klogd: sd 2:0:0:0: [sdb] READ CAPACITY failed
May 18 19:43:52 MadNoutV3 klogd: sd 2:0:0:0: [sdb] Result: hostbyte=DID_BAD_TARGET driverbyte=DRIVER_OK,SUGGEST_OK
May 18 19:43:52 MadNoutV3 klogd: sd 2:0:0:0: [sdb] Sense not available.
May 18 19:43:52 MadNoutV3 klogd: sd 2:0:0:0: [sdb] Write Protect is off
May 18 19:43:52 MadNoutV3 klogd: sd 2:0:0:0: [sdb] Mode Sense: 00 00 00 00
May 18 19:43:52 MadNoutV3 klogd: sd 2:0:0:0: [sdb] Asking for cache data failed
May 18 19:43:52 MadNoutV3 klogd: sd 2:0:0:0: [sdb] Assuming drive cache: write through
May 18 19:43:52 MadNoutV3 klogd: sd 2:0:0:0: [sdb] READ CAPACITY failed
May 18 19:43:52 MadNoutV3 klogd: sd 2:0:0:0: [sdb] Result: hostbyte=DID_BAD_TARGET driverbyte=DRIVER_OK,SUGGEST_OK
May 18 19:43:52 MadNoutV3 klogd: sd 2:0:0:0: [sdb] Sense not available.
May 18 19:43:52 MadNoutV3 klogd: sd 2:0:0:0: [sdb] Write Protect is off
May 18 19:43:52 MadNoutV3 klogd: sd 2:0:0:0: [sdb] Mode Sense: 00 00 00 00
May 18 19:43:52 MadNoutV3 klogd: sd 2:0:0:0: [sdb] Asking for cache data failed
May 18 19:43:52 MadNoutV3 klogd: sd 2:0:0:0: [sdb] Assuming drive cache: write through
May 18 19:43:52 MadNoutV3 klogd: sd 2:0:0:0: [sdb] READ CAPACITY failed
May 18 19:43:52 MadNoutV3 klogd: sd 2:0:0:0: [sdb] Result: hostbyte=DID_BAD_TARGET driverbyte=DRIVER_OK,SUGGEST_OK
May 18 19:43:52 MadNoutV3 klogd: sd 2:0:0:0: [sdb] Sense not available.
May 18 19:43:52 MadNoutV3 klogd: sd 2:0:0:0: [sdb] Write Protect is off
May 18 19:43:52 MadNoutV3 klogd: sd 2:0:0:0: [sdb] Mode Sense: 00 00 00 00
May 18 19:43:52 MadNoutV3 klogd: sd 2:0:0:0: [sdb] Asking for cache data failed
May 18 19:43:52 MadNoutV3 klogd: sd 2:0:0:0: [sdb] Assuming drive cache: write through
May 18 19:43:52 MadNoutV3 klogd: sd 2:0:0:0: [sdb] READ CAPACITY failed
May 18 19:43:52 MadNoutV3 klogd: sd 2:0:0:0: [sdb] Result: hostbyte=DID_BAD_TARGET driverbyte=DRIVER_OK,SUGGEST_OK
May 18 19:43:52 MadNoutV3 klogd: sd 2:0:0:0: [sdb] Sense not available.
May 18 19:43:52 MadNoutV3 klogd: sd 2:0:0:0: [sdb] Write Protect is off
May 18 19:43:52 MadNoutV3 klogd: sd 2:0:0:0: [sdb] Mode Sense: 00 00 00 00
May 18 19:43:52 MadNoutV3 klogd: sd 2:0:0:0: [sdb] Asking for cache data failed
May 18 19:43:52 MadNoutV3 klogd: sd 2:0:0:0: [sdb] Assuming drive cache: write through
May 18 19:43:52 MadNoutV3 klogd: sd 2:0:0:0: [sdb] READ CAPACITY failed
May 18 19:43:52 MadNoutV3 klogd: sd 2:0:0:0: [sdb] Result: hostbyte=DID_BAD_TARGET driverbyte=DRIVER_OK,SUGGEST_OK
May 18 19:43:52 MadNoutV3 klogd: sd 2:0:0:0: [sdb] Sense not available.
May 18 19:43:52 MadNoutV3 klogd: sd 2:0:0:0: [sdb] Write Protect is off
May 18 19:43:52 MadNoutV3 klogd: sd 2:0:0:0: [sdb] Mode Sense: 00 00 00 00
May 18 19:43:52 MadNoutV3 klogd: sd 2:0:0:0: [sdb] Asking for cache data failed
May 18 19:43:52 MadNoutV3 klogd: sd 2:0:0:0: [sdb] Assuming drive cache: write through
May 18 19:43:52 MadNoutV3 klogd: sd 2:0:0:0: [sdb] READ CAPACITY failed
May 18 19:43:52 MadNoutV3 klogd: sd 2:0:0:0: [sdb] Result: hostbyte=DID_BAD_TARGET driverbyte=DRIVER_OK,SUGGEST_OK
May 18 19:43:52 MadNoutV3 klogd: sd 2:0:0:0: [sdb] Sense not available.
May 18 19:43:52 MadNoutV3 klogd: sd 2:0:0:0: [sdb] Write Protect is off
May 18 19:43:52 MadNoutV3 klogd: sd 2:0:0:0: [sdb] Mode Sense: 00 00 00 00
May 18 19:43:52 MadNoutV3 klogd: sd 2:0:0:0: [sdb] Asking for cache data failed
May 18 19:43:52 MadNoutV3 klogd: sd 2:0:0:0: [sdb] Assuming drive cache: write through
May 18 19:43:52 MadNoutV3 klogd: sd 2:0:0:0: [sdb] READ CAPACITY failed
May 18 19:43:52 MadNoutV3 klogd: sd 2:0:0:0: [sdb] Result: hostbyte=DID_BAD_TARGET driverbyte=DRIVER_OK,SUGGEST_OK

Последние сообщения про sdb повторяются бесконечно....

Вывод ifconfig:

Код:

[root@MadNoutV3 san]# ifconfig
eth0      Link encap:Ethernet  HWaddr 00:00:39:72:11:9F
          UP BROADCAST MULTICAST  MTU:1500  Metric:1
          RX packets:0 errors:0 dropped:0 overruns:0 frame:0
          TX packets:0 errors:0 dropped:0 overruns:0 carrier:0
          collisions:0 txqueuelen:1000
          RX bytes:0 (0.0 b)  TX bytes:0 (0.0 b)

lo        Link encap:Local Loopback
          inet addr:127.0.0.1  Mask:255.0.0.0
          inet6 addr: ::1/128 Scope:Host
          UP LOOPBACK RUNNING  MTU:16436  Metric:1
          RX packets:7204 errors:0 dropped:0 overruns:0 frame:0
          TX packets:7204 errors:0 dropped:0 overruns:0 carrier:0
          collisions:0 txqueuelen:0
          RX bytes:6947151 (6.6 MiB)  TX bytes:6947151 (6.6 MiB)

Вывод iwconfig:

Код:

[root@MadNoutV3 san]# iwconfig
lo        no wireless extensions.

eth0      no wireless extensions.

pan0      no wireless extensions.

wifi0     IEEE 802.11-DS  Mode:Managed
          Encryption key:off

wlan0     IEEE 802.11-DS  Mode:Managed
          Encryption key:off
          Link Quality:0  Signal level:0  Noise level:0
          Rx invalid nwid:0  Rx invalid crypt:0  Rx invalid frag:0
          Tx excessive retries:0  Invalid misc:0   Missed beacon:0

Настроек pan0, wifi0 в /etc/sysconfig/network-scripts/ нет, откуда они появляются, сам не знаю

Вывод iwlist:

Код:

[root@MadNoutV3 san]# iwlist scanning
lo        Interface doesn't support scanning.

eth0      Interface doesn't support scanning.

pan0      Interface doesn't support scanning.

wifi0     Interface doesn't support scanning : Network is down

wlan0     Interface doesn't support scanning : Network is down

[root@MadNoutV3 san]# iwlist wlan0 scanning
wlan0     Interface doesn't support scanning : Network is down

Настройки сетевого устройства wi-fi следующие:

Код:

[root@MadNoutV3 hostapd]# cat /etc/sysconfig/network-scripts/ifcfg-wlan0
DEVICE=wlan0
BOOTPROTO=static
IPADDR=192.168.1.10
NETMASK=255.255.255.0
GATEWAY=192.168.1.101
ONBOOT=yes
METRIC=35
MII_NOT_SUPPORTED=no
USERCTL=no
DNS1=192.168.1.101
RESOLV_MODS=no
WIRELESS_MODE=Ad-hoc
WIRELESS_ESSID=homnet
WIRELESS_ENC_KEY=s:d3841c25a05040b1a78c6380b5
WIRELESS_ENC_MODE=open
WIRELESS_WPA_DRIVER=hostap
WIRELESS_WPA_REASSOCIATE=no
IPV6INIT=no
IPV6TO4INIT=no

Настройка wifi сети homnet:

Код:

[root@MadNoutV3 hostapd]# cat /etc/sysconfig/network-scripts/wireless.d/homnet
BOOTPROTO=static
IPADDR=192.168.1.10
NETMASK=255.255.255.0
GATEWAY=192.168.1.101
METRIC=35
USERCTL=no
DNS1=192.168.1.101
RESOLV_MODS=no
WIRELESS_MODE=Ad-hoc
WIRELESS_ESSID=homnet
WIRELESS_ENC_KEY=s:d3841c25a05040b1a78c6380b5
WIRELESS_ENC_MODE=open
WIRELESS_WPA_DRIVER=hostap
WIRELESS_WPA_REASSOCIATE=no
IPV6INIT=no
IPV6TO4INIT=no

Когда пробую перезапускать hostapd, ругается, но не пойму на что:

Код:

[root@MadNoutV3 hostapd]# /etc/init.d/hostapd restart
Stopping Hostapd:                                               [ ОШИБКА ]
Starting Hostapd: Configuration file: /etc/hostapd/hostapd.conf
ioctl[SIOCSIFFLAGS]: Cannot assign requested address
hostap driver initialization failed.
rmdir[ctrl_interface]: No such file or directory
ELOOP: remaining socket: sock=4 eloop_data=0x9371188 user_data=(nil) handler=0x8074ee0
                                                                [ ОШИБКА ]

Когда перезапускаю сеть, то же ругается:

Код:

[root@MadNoutV3 hostapd]# /etc/init.d/network restart
Shutting down interface eth0:                                   [   ОК  ]
Shutting down loopback interface:                               [   ОК  ]
Bringing up loopback interface:                                 [   ОК  ]
Configuring wireless regulatory domain  nl80211 not found.
                                                                [ ОШИБКА ]
Bringing up interface eth0:                                     [   ОК  ]
Bringing up interface wlan0:  RTNETLINK answers: Cannot assign requested address
RTNETLINK answers: Cannot assign requested address
nl80211 not found.
Error for wireless request "Set Encode" (8B2A) :
    SET failed on device wlan0 ; Invalid argument.
Error for wireless request "Set Mode" (8B06) :
    SET failed on device wlan0 ; Operation not supported.
Error for wireless request "Set Encode" (8B2A) :
    SET failed on device wlan0 ; Invalid argument.
Error for wireless request "Set ESSID" (8B1A) :
    SET failed on device wlan0 ; Invalid argument.
Another wpa_supplicant instance is already running for device wlan0
                                                                [ ОШИБКА ]
Bringing up interface ppp0:  Cannot find device "ppp0"
Using interface ppp0
Connect: ppp0 <--> /dev/pts/4
^CTerminating on signal 2
Child process pppoe -m 1412 -I eth0 (pid 5283) terminated with signal 2
Modem hangup
Connection terminated.
                                                                [ ОШИБКА ]

Меня смущает вот этот "nl80211 not found". Но где его брать и куда положить, непонятно.

Хотя, с другой стороны, в конфиге hostapd.conf написано

Код:

# Driver interface type (hostap/wired/madwifi/prism54/test/none/nl80211/bsd);
# default: hostap). nl80211 is used with all Linux mac80211 drivers.
# Use driver=none if building hostapd as a standalone RADIUS server that does
# not control any wireless/wired driver.
driver=hostap

Прошу помощи, уважаемые, чувствую, что самому не разобраться.

SANyaSmolenskii · Сообщение **SANyaSmolenskii** » 22.07.2009 02:14

Поднимаю тему, сам решения не нашел, а надо.

после доолгих поисков нашел в интернете мануал, как запустить карточку http://electrons.psychogenic.com/modules/a...rLinuxiPAQs.php
Нужно установить пакеты hostap-utils, prism, и firmware для моей карты.

До этого устанавливал hostapd , а он нужен если делать точку доступа, что мне не надо, да и вряд ли карта поддерживает.

Делаю все по мануалу, все идет нормально, загорается лампочка на карточке (!), могу уже запустить поиск беспроводных сетей, и нахожу свою сеть. То есть я понимаю, что карта работает.

Но когда я подключаюсь к своей сетке, апплет сетевых соединений показывает, что я к ней подключен,
но уровень сигнала 0%.
И пинг до соседнего компьютера не идет.

содержимое ifcfg-wlan0

Код:

DEVICE=wlan0
BOOTPROTO=static
IPADDR=192.168.1.100
NETMASK=255.255.255.0
GATEWAY=192.168.1.101
ONBOOT=yes
METRIC=35
MII_NOT_SUPPORTED=no
USERCTL=no
DNS1=192.168.1.101
RESOLV_MODS=no
WIRELESS_MODE=Ad-Hoc
WIRELESS_ESSID=homnet
WIRELESS_ENC_KEY=s:d3841c25a05040b1a78c6380b5
WIRELESS_ENC_MODE=open
IPV6INIT=no
IPV6TO4INIT=no

вывод ifconfig

Код:

eth0      Link encap:Ethernet  HWaddr 00:00:39:72:11:9F
          UP BROADCAST MULTICAST  MTU:1500  Metric:1
          RX packets:0 errors:0 dropped:0 overruns:0 frame:0
          TX packets:0 errors:0 dropped:0 overruns:0 carrier:0
          collisions:0 txqueuelen:1000
          RX bytes:0 (0.0 b)  TX bytes:0 (0.0 b)

lo        Link encap:Local Loopback
          inet addr:127.0.0.1  Mask:255.0.0.0
          inet6 addr: ::1/128 Scope:Host
          UP LOOPBACK RUNNING  MTU:16436  Metric:1
          RX packets:67 errors:0 dropped:0 overruns:0 frame:0
          TX packets:67 errors:0 dropped:0 overruns:0 carrier:0
          collisions:0 txqueuelen:0
          RX bytes:6104 (5.9 KiB)  TX bytes:6104 (5.9 KiB)

wifi0     Link encap:UNSPEC  HWaddr 00-60-B3-6C-36-5F-40-AE-00-00-00-00-00-00-00-00
          UP BROADCAST RUNNING MULTICAST  MTU:1500  Metric:1
          RX packets:0 errors:0 dropped:0 overruns:0 frame:0
          TX packets:7 errors:0 dropped:191 overruns:0 carrier:0
          collisions:0 txqueuelen:1000
          RX bytes:0 (0.0 b)  TX bytes:684 (684.0 b)
          Interrupt:3 Base address:0xd180

wlan0     Link encap:Ethernet  HWaddr 00:60:B3:6C:36:5F
          inet addr:192.168.1.100  Bcast:192.168.1.255  Mask:255.255.255.0
          inet6 addr: fe80::260:b3ff:fe6c:365f/64 Scope:Link
          UP BROADCAST RUNNING MULTICAST  MTU:1500  Metric:1
          RX packets:0 errors:0 dropped:0 overruns:0 frame:0
          TX packets:198 errors:0 dropped:0 overruns:0 carrier:0
          collisions:0 txqueuelen:0
          RX bytes:0 (0.0 b)  TX bytes:20703 (20.2 KiB)
          Interrupt:3 Base address:0xd180

вывод iwconfig

Код:

wifi0     IEEE 802.11b  ESSID:"homnet"  Nickname:"localhost"
          Mode:Ad-Hoc  Frequency:2.462 GHz  Cell: 5E:E3:F5:DF:33:92
          Bit Rate:11 Mb/s   Sensitivity=1/3
          Retry short limit:8   RTS thr:off   Fragment thr:off
          Encryption key:6433-3834-3163-3235-6130-3530-34   Security mode:open
          Power Management:off

wlan0     IEEE 802.11b  ESSID:"homnet"  Nickname:"localhost"
          Mode:Ad-Hoc  Frequency:2.462 GHz  Cell: 5E:E3:F5:DF:33:92
          Bit Rate:11 Mb/s   Sensitivity=1/3
          Retry short limit:8   RTS thr:off   Fragment thr:off
          Encryption key:6433-3834-3163-3235-6130-3530-34   Security mode:open
          Power Management:off
          Link Quality=0/70  Signal level=-73 dBm  Noise level=-73 dBm
          Rx invalid nwid:0  Rx invalid crypt:0  Rx invalid frag:0
          Tx excessive retries:10  Invalid misc:7   Missed beacon:0

вывод iwlist scan

Код:

wifi0     Scan completed :
          Cell 01 - Address: 5E:E3:F5:DF:33:92
                    ESSID:"homnet"
                    Mode:Ad-Hoc
                    Frequency:2.462 GHz (Channel 11)
                    Signal level=-36 dBm  Noise level=-86 dBm
                    Encryption key:on
                    Bit Rates:1 Mb/s; 2 Mb/s; 5.5 Mb/s; 11 Mb/s
                    Extra:bcn_int=100
                    Extra:resp_rate=10
                    Extra:atim=0

wlan0     Scan completed :
          Cell 01 - Address: 5E:E3:F5:DF:33:92
                    ESSID:"homnet"
                    Mode:Ad-Hoc
                    Frequency:2.462 GHz (Channel 11)
                    Signal level=-36 dBm  Noise level=-89 dBm
                    Encryption key:on
                    Bit Rates:1 Mb/s; 2 Mb/s; 5.5 Mb/s; 11 Mb/s
                    Extra:bcn_int=100
                    Extra:resp_rate=10
                    Extra:atim=0

В какую сторону копать, подскажите....

unixforum.org

SanDisk SDWCFB-128 Connect Plus 128MB + Wi-Fi CompactFlash (Не работает, не знаю почему .....)

SanDisk SDWCFB-128 Connect Plus 128MB + Wi-Fi CompactFlash

Re: SanDisk SDWCFB-128 Connect Plus 128MB + Wi-Fi CompactFlash