Добрый день. Это мой первый опыт работы с Linux. Есть сервер Dell,если правильно понял,
у него есть рейд контроллер Dell Perc H700. Стоит Ubuntu 16.04 LTS 64-разрядная desktop и samba. Сервер находится в домене. До определенного момента все работало хорошо и был доступ к шаре на сервере. Потом в один момент пропал доступ и шара визуально то появляется то исчезает.
В конфиге smb.conf в секции Share Definitions нашел секцию path, как мне кажется,там прописан путь к шаре, которая пропала. По этому пути указанной папки нет. На сервере сейчас есть массив 12 ТБ, доступа к которому нет. Есть предположение, что это и есть отвалившийся раздел. Пробовал монтировать его но выдает ошибку: mount: /dev/sdb: can't read superblock.
Информации о том был ли это рэйд нет. Сервер достался уже настроенным.
test disk выдает при анализе диска выдает partition read error.
Подскажите, пожалуйста, как можно узнать что произошло с сервером? Где можно посмотреть логи и как можно восстановить инфрмацию. Еще такой нюанс, возможно это тоже как-то связано, при старте сервера есть ошибка что батарея рейд контроллера разряжена.
проблема с жестким диском
Модераторы: SLEDopit, Модераторы разделов
-
userkom
- Сообщения: 5
- ОС: Linux
проблема с жестким диском
У вас нет необходимых прав для просмотра вложений в этом сообщении.
-
Bizdelnick
- Модератор
- Сообщения: 21245
- Статус: nulla salus bello
- ОС: Debian GNU/Linux
Re: проблема с жестким диском
Смотрите smartctl -a /dev/sdb (если такой команды нет, надо установить пакет smartmontools). Если это аппаратный RAID, ничего вразумительного в выводе, скорее всего, не будет, и надо будут использовать спец. софт для работы с ним.
Пишите правильно:
| в консоли вку́пе (с чем-либо) в общем вообще | в течение (часа) новичок нюанс по умолчанию | приемлемо проблема пробовать трафик |
-
userkom
- Сообщения: 5
- ОС: Linux
Re: проблема с жестким диском
выполнили ваши рекомендации, результат следующий!
admin82@ROSSTAT-DATA-SERVER:~$ smartctl -a /dev/sdb
smartctl 6.5 2016-01-24 r4214 [x86_64-linux-4.10.0-28-generic] (local build)
Copyright (C) 2002-16, Bruce Allen, Christian Franke, www.smartmontools.org
Smartctl open device: /dev/sdb failed: Permission denied
admin82@ROSSTAT-DATA-SERVER:~$
admin82@ROSSTAT-DATA-SERVER:~$ sudo smartctl -a /dev/sdb
smartctl 6.5 2016-01-24 r4214 [x86_64-linux-4.10.0-28-generic] (local build)
Copyright (C) 2002-16, Bruce Allen, Christian Franke, www.smartmontools.org
Smartctl open device: /dev/sdb failed: DELL or MegaRaid controller, please try adding '-d megaraid,N'
admin82@ROSSTAT-DATA-SERVER:~$
admin82@ROSSTAT-DATA-SERVER:~$ smartctl -a /dev/sdb
smartctl 6.5 2016-01-24 r4214 [x86_64-linux-4.10.0-28-generic] (local build)
Copyright (C) 2002-16, Bruce Allen, Christian Franke, www.smartmontools.org
Smartctl open device: /dev/sdb failed: Permission denied
admin82@ROSSTAT-DATA-SERVER:~$
admin82@ROSSTAT-DATA-SERVER:~$ sudo smartctl -a /dev/sdb
smartctl 6.5 2016-01-24 r4214 [x86_64-linux-4.10.0-28-generic] (local build)
Copyright (C) 2002-16, Bruce Allen, Christian Franke, www.smartmontools.org
Smartctl open device: /dev/sdb failed: DELL or MegaRaid controller, please try adding '-d megaraid,N'
admin82@ROSSTAT-DATA-SERVER:~$
-
Bizdelnick
- Модератор
- Сообщения: 21245
- Статус: nulla salus bello
- ОС: Debian GNU/Linux
Re: проблема с жестким диском
Ну да, RAID. Попробуйте сделать, как советует smartctl:
То есть sudo smartctl -a -d megaraid,0 /dev/sdb и т. д., увеличивая цифру до последнего диска.
N — это номер диска, насколько я понимаю.
То есть sudo smartctl -a -d megaraid,0 /dev/sdb и т. д., увеличивая цифру до последнего диска.
Пишите правильно:
| в консоли вку́пе (с чем-либо) в общем вообще | в течение (часа) новичок нюанс по умолчанию | приемлемо проблема пробовать трафик |
-
userkom
- Сообщения: 5
- ОС: Linux
Re: проблема с жестким диском
Выполнили проверку результат следующий.
Код: Выделить всё
0
admin82@ROSSTAT-DATA-SERVER:~$ sudo smartctl -a -d megaraid,0 /dev/sdb
smartctl 6.5 2016-01-24 r4214 [x86_64-linux-4.10.0-28-generic] (local build)
Copyright (C) 2002-16, Bruce Allen, Christian Franke, www.smartmontools.org
/dev/sdb [megaraid_disk_00] [SAT]: Device open changed type from 'megaraid,0' to 'sat+megaraid,0'
=== START OF INFORMATION SECTION ===
Model Family: Seagate Constellation ES (SATA 6Gb/s)
Device Model: ST2000NM0011
Serial Number: Z1P1X2PT
LU WWN Device Id: 5 000c50 040464bc1
Add. Product Id: DELL(tm)
Firmware Version: PA03
User Capacity: 2 000 398 934 016 bytes [2,00 TB]
Sector Size: 512 bytes logical/physical
Rotation Rate: 7202 rpm
Form Factor: 3.5 inches
Device is: In smartctl database [for details use: -P show]
ATA Version is: ATA8-ACS T13/1699-D revision 4
SATA Version is: SATA 3.0, 3.0 Gb/s (current: 3.0 Gb/s)
Local Time is: Thu Oct 31 14:08:49 2019 MSK
SMART support is: Available - device has SMART capability.
SMART support is: Enabled
=== START OF READ SMART DATA SECTION ===
SMART Status not supported: ATA return descriptor not supported by controller firmware
SMART overall-health self-assessment test result: PASSED
Warning: This result is based on an Attribute check.
General SMART Values:
Offline data collection status: (0x82) Offline data collection activity
was completed without error.
Auto Offline Data Collection: Enabled.
Self-test execution status: ( 0) The previous self-test routine completed
without error or no self-test has ever
been run.
Total time to complete Offline
data collection: ( 609) seconds.
Offline data collection
capabilities: (0x7b) SMART execute Offline immediate.
Auto Offline data collection on/off support.
Suspend Offline collection upon new
command.
Offline surface scan supported.
Self-test supported.
Conveyance Self-test supported.
Selective Self-test supported.
SMART capabilities: (0x0003) Saves SMART data before entering
power-saving mode.
Supports SMART auto save timer.
Error logging capability: (0x01) Error logging supported.
General Purpose Logging supported.
Short self-test routine
recommended polling time: ( 2) minutes.
Extended self-test routine
recommended polling time: ( 304) minutes.
Conveyance self-test routine
recommended polling time: ( 3) minutes.
SCT capabilities: (0x10bd) SCT Status supported.
SCT Error Recovery Control supported.
SCT Feature Control supported.
SCT Data Table supported.
SMART Attributes Data Structure revision number: 10
Vendor Specific SMART Attributes with Thresholds:
ID# ATTRIBUTE_NAME FLAG VALUE WORST THRESH TYPE UPDATED WHEN_FAILED RAW_VALUE
1 Raw_Read_Error_Rate 0x000f 081 063 044 Pre-fail Always - 150274366
3 Spin_Up_Time 0x0003 089 087 000 Pre-fail Always - 0
4 Start_Stop_Count 0x0032 100 100 020 Old_age Always - 84
5 Reallocated_Sector_Ct 0x0033 100 100 036 Pre-fail Always - 6
7 Seek_Error_Rate 0x000f 072 060 030 Pre-fail Always - 17245534
9 Power_On_Hours 0x0032 075 075 000 Old_age Always - 22696
10 Spin_Retry_Count 0x0013 100 100 097 Pre-fail Always - 0
12 Power_Cycle_Count 0x0032 100 100 020 Old_age Always - 80
184 End-to-End_Error 0x0032 100 100 099 Old_age Always - 0
187 Reported_Uncorrect 0x0032 100 100 000 Old_age Always - 0
188 Command_Timeout 0x0032 100 099 000 Old_age Always - 4295032833
189 High_Fly_Writes 0x003a 100 100 000 Old_age Always - 0
190 Airflow_Temperature_Cel 0x0022 067 047 045 Old_age Always - 33 (Min/Max 21/34)
191 G-Sense_Error_Rate 0x0032 100 100 000 Old_age Always - 0
192 Power-Off_Retract_Count 0x0032 100 100 000 Old_age Always - 83
193 Load_Cycle_Count 0x0032 100 100 000 Old_age Always - 84
194 Temperature_Celsius 0x0022 033 053 000 Old_age Always - 33 (0 18 0 0 0)
195 Hardware_ECC_Recovered 0x001a 117 099 000 Old_age Always - 150274366
197 Current_Pending_Sector 0x0012 100 100 000 Old_age Always - 0
198 Offline_Uncorrectable 0x0010 100 100 000 Old_age Offline - 0
199 UDMA_CRC_Error_Count 0x003e 200 200 000 Old_age Always - 0
240 Head_Flying_Hours 0x0000 100 253 000 Old_age Offline - 22164 (112 111 0)
241 Total_LBAs_Written 0x0000 100 253 000 Old_age Offline - 81690715
242 Total_LBAs_Read 0x0000 100 253 000 Old_age Offline - 414504624
SMART Error Log Version: 1
No Errors Logged
SMART Self-test log structure revision number 1
Num Test_Description Status Remaining LifeTime(hours) LBA_of_first_error
# 1 Extended offline Completed without error 00% 15 -
# 2 Extended offline Aborted by host 70% 10 -
# 3 Short offline Completed without error 00% 9 -
# 4 Extended offline Completed without error 00% 6 -
SMART Selective self-test log data structure revision number 1
SPAN MIN_LBA MAX_LBA CURRENT_TEST_STATUS
1 0 0 Not_testing
2 0 0 Not_testing
3 0 0 Not_testing
4 0 0 Not_testing
5 0 0 Not_testing
Selective self-test flags (0x0):
After scanning selected spans, do NOT read-scan remainder of disk.
If Selective self-test is pending on power-up, resume after 0 minute delay.
admin82@ROSSTAT-DATA-SERVER:~$
-----------------------------------------------------
1
admin82@ROSSTAT-DATA-SERVER:~$ sudo smartctl -a -d megaraid,1 /dev/sdb
smartctl 6.5 2016-01-24 r4214 [x86_64-linux-4.10.0-28-generic] (local build)
Copyright (C) 2002-16, Bruce Allen, Christian Franke, www.smartmontools.org
/dev/sdb [megaraid_disk_01] [SAT]: Device open changed type from 'megaraid,1' to 'sat+megaraid,1'
=== START OF INFORMATION SECTION ===
Model Family: Seagate Constellation ES (SATA 6Gb/s)
Device Model: ST2000NM0011
Serial Number: Z1P1X7P6
LU WWN Device Id: 5 000c50 0404758e9
Add. Product Id: DELL(tm)
Firmware Version: PA03
User Capacity: 2 000 398 934 016 bytes [2,00 TB]
Sector Size: 512 bytes logical/physical
Rotation Rate: 7202 rpm
Form Factor: 3.5 inches
Device is: In smartctl database [for details use: -P show]
ATA Version is: ATA8-ACS T13/1699-D revision 4
SATA Version is: SATA 3.0, 3.0 Gb/s (current: 3.0 Gb/s)
Local Time is: Thu Oct 31 14:18:56 2019 MSK
SMART support is: Available - device has SMART capability.
SMART support is: Enabled
=== START OF READ SMART DATA SECTION ===
SMART Status not supported: ATA return descriptor not supported by controller firmware
SMART overall-health self-assessment test result: PASSED
Warning: This result is based on an Attribute check.
General SMART Values:
Offline data collection status: (0x82) Offline data collection activity
was completed without error.
Auto Offline Data Collection: Enabled.
Self-test execution status: ( 0) The previous self-test routine completed
without error or no self-test has ever
been run.
Total time to complete Offline
data collection: ( 600) seconds.
Offline data collection
capabilities: (0x7b) SMART execute Offline immediate.
Auto Offline data collection on/off support.
Suspend Offline collection upon new
command.
Offline surface scan supported.
Self-test supported.
Conveyance Self-test supported.
Selective Self-test supported.
SMART capabilities: (0x0003) Saves SMART data before entering
power-saving mode.
Supports SMART auto save timer.
Error logging capability: (0x01) Error logging supported.
General Purpose Logging supported.
Short self-test routine
recommended polling time: ( 2) minutes.
Extended self-test routine
recommended polling time: ( 291) minutes.
Conveyance self-test routine
recommended polling time: ( 3) minutes.
SCT capabilities: (0x10bd) SCT Status supported.
SCT Error Recovery Control supported.
SCT Feature Control supported.
SCT Data Table supported.
SMART Attributes Data Structure revision number: 10
Vendor Specific SMART Attributes with Thresholds:
ID# ATTRIBUTE_NAME FLAG VALUE WORST THRESH TYPE UPDATED WHEN_FAILED RAW_VALUE
1 Raw_Read_Error_Rate 0x000f 072 063 044 Pre-fail Always - 15529800
3 Spin_Up_Time 0x0003 089 088 000 Pre-fail Always - 0
4 Start_Stop_Count 0x0032 100 100 020 Old_age Always - 86
5 Reallocated_Sector_Ct 0x0033 100 100 036 Pre-fail Always - 24
7 Seek_Error_Rate 0x000f 069 060 030 Pre-fail Always - 8864910
9 Power_On_Hours 0x0032 075 075 000 Old_age Always - 22571
10 Spin_Retry_Count 0x0013 100 100 097 Pre-fail Always - 0
12 Power_Cycle_Count 0x0032 100 100 020 Old_age Always - 82
184 End-to-End_Error 0x0032 100 100 099 Old_age Always - 0
187 Reported_Uncorrect 0x0032 100 100 000 Old_age Always - 0
188 Command_Timeout 0x0032 100 098 000 Old_age Always - 12885098499
189 High_Fly_Writes 0x003a 100 100 000 Old_age Always - 0
190 Airflow_Temperature_Cel 0x0022 065 046 045 Old_age Always - 35 (Min/Max 21/35)
191 G-Sense_Error_Rate 0x0032 100 100 000 Old_age Always - 0
192 Power-Off_Retract_Count 0x0032 100 100 000 Old_age Always - 85
193 Load_Cycle_Count 0x0032 100 100 000 Old_age Always - 86
194 Temperature_Celsius 0x0022 035 054 000 Old_age Always - 35 (0 18 0 0 0)
195 Hardware_ECC_Recovered 0x001a 108 099 000 Old_age Always - 15529800
197 Current_Pending_Sector 0x0012 100 100 000 Old_age Always - 0
198 Offline_Uncorrectable 0x0010 100 100 000 Old_age Offline - 0
199 UDMA_CRC_Error_Count 0x003e 200 200 000 Old_age Always - 0
240 Head_Flying_Hours 0x0000 100 253 000 Old_age Offline - 8716 (245 116 0)
241 Total_LBAs_Written 0x0000 100 253 000 Old_age Offline - 2261225796
242 Total_LBAs_Read 0x0000 100 253 000 Old_age Offline - 3972340201
SMART Error Log Version: 1
No Errors Logged
SMART Self-test log structure revision number 1
Num Test_Description Status Remaining LifeTime(hours) LBA_of_first_error
# 1 Extended offline Completed without error 00% 15 -
# 2 Extended offline Aborted by host 70% 10 -
# 3 Short offline Completed without error 00% 9 -
# 4 Extended offline Completed without error 00% 6 -
SMART Selective self-test log data structure revision number 1
SPAN MIN_LBA MAX_LBA CURRENT_TEST_STATUS
1 0 0 Not_testing
2 0 0 Not_testing
3 0 0 Not_testing
4 0 0 Not_testing
5 0 0 Not_testing
Selective self-test flags (0x0):
After scanning selected spans, do NOT read-scan remainder of disk.
If Selective self-test is pending on power-up, resume after 0 minute delay.
admin82@ROSSTAT-DATA-SERVER:~$
---------------------------------------------------------
2
admin82@ROSSTAT-DATA-SERVER:~$ sudo smartctl -a -d megaraid,2 /dev/sdb
smartctl 6.5 2016-01-24 r4214 [x86_64-linux-4.10.0-28-generic] (local build)
Copyright (C) 2002-16, Bruce Allen, Christian Franke, www.smartmontools.org
/dev/sdb [megaraid_disk_02] [SAT]: Device open changed type from 'megaraid,2' to 'sat+megaraid,2'
=== START OF INFORMATION SECTION ===
Model Family: Seagate Constellation ES (SATA 6Gb/s)
Device Model: ST2000NM0011
Serial Number: Z1P1XM9C
LU WWN Device Id: 5 000c50 040493a7f
Add. Product Id: DELL(tm)
Firmware Version: PA03
User Capacity: 2 000 398 934 016 bytes [2,00 TB]
Sector Size: 512 bytes logical/physical
Rotation Rate: 7202 rpm
Form Factor: 3.5 inches
Device is: In smartctl database [for details use: -P show]
ATA Version is: ATA8-ACS T13/1699-D revision 4
SATA Version is: SATA 3.0, 3.0 Gb/s (current: 3.0 Gb/s)
Local Time is: Thu Oct 31 14:17:16 2019 MSK
SMART support is: Available - device has SMART capability.
SMART support is: Enabled
=== START OF READ SMART DATA SECTION ===
SMART Status not supported: ATA return descriptor not supported by controller firmware
SMART overall-health self-assessment test result: PASSED
Warning: This result is based on an Attribute check.
General SMART Values:
Offline data collection status: (0x82) Offline data collection activity
was completed without error.
Auto Offline Data Collection: Enabled.
Self-test execution status: ( 0) The previous self-test routine completed
without error or no self-test has ever
been run.
Total time to complete Offline
data collection: ( 609) seconds.
Offline data collection
capabilities: (0x7b) SMART execute Offline immediate.
Auto Offline data collection on/off support.
Suspend Offline collection upon new
command.
Offline surface scan supported.
Self-test supported.
Conveyance Self-test supported.
Selective Self-test supported.
SMART capabilities: (0x0003) Saves SMART data before entering
power-saving mode.
Supports SMART auto save timer.
Error logging capability: (0x01) Error logging supported.
General Purpose Logging supported.
Short self-test routine
recommended polling time: ( 2) minutes.
Extended self-test routine
recommended polling time: ( 303) minutes.
Conveyance self-test routine
recommended polling time: ( 3) minutes.
SCT capabilities: (0x10bd) SCT Status supported.
SCT Error Recovery Control supported.
SCT Feature Control supported.
SCT Data Table supported.
SMART Attributes Data Structure revision number: 10
Vendor Specific SMART Attributes with Thresholds:
ID# ATTRIBUTE_NAME FLAG VALUE WORST THRESH TYPE UPDATED WHEN_FAILED RAW_VALUE
1 Raw_Read_Error_Rate 0x000f 080 063 044 Pre-fail Always - 116270837
3 Spin_Up_Time 0x0003 089 087 000 Pre-fail Always - 0
4 Start_Stop_Count 0x0032 100 100 020 Old_age Always - 90
5 Reallocated_Sector_Ct 0x0033 100 100 036 Pre-fail Always - 0
7 Seek_Error_Rate 0x000f 072 060 030 Pre-fail Always - 15349167
9 Power_On_Hours 0x0032 075 075 000 Old_age Always - 22586
10 Spin_Retry_Count 0x0013 100 100 097 Pre-fail Always - 0
12 Power_Cycle_Count 0x0032 100 100 020 Old_age Always - 86
184 End-to-End_Error 0x0032 100 100 099 Old_age Always - 0
187 Reported_Uncorrect 0x0032 100 100 000 Old_age Always - 0
188 Command_Timeout 0x0032 100 100 000 Old_age Always - 0
189 High_Fly_Writes 0x003a 100 100 000 Old_age Always - 0
190 Airflow_Temperature_Cel 0x0022 066 046 045 Old_age Always - 34 (Min/Max 22/34)
191 G-Sense_Error_Rate 0x0032 100 100 000 Old_age Always - 0
192 Power-Off_Retract_Count 0x0032 100 100 000 Old_age Always - 89
193 Load_Cycle_Count 0x0032 100 100 000 Old_age Always - 90
194 Temperature_Celsius 0x0022 034 054 000 Old_age Always - 34 (0 19 0 0 0)
195 Hardware_ECC_Recovered 0x001a 116 099 000 Old_age Always - 116270837
197 Current_Pending_Sector 0x0012 100 100 000 Old_age Always - 0
198 Offline_Uncorrectable 0x0010 100 100 000 Old_age Offline - 0
199 UDMA_CRC_Error_Count 0x003e 200 200 000 Old_age Always - 0
240 Head_Flying_Hours 0x0000 100 253 000 Old_age Offline - 8704 (117 44 0)
241 Total_LBAs_Written 0x0000 100 253 000 Old_age Offline - 2290652653
242 Total_LBAs_Read 0x0000 100 253 000 Old_age Offline - 95225967
SMART Error Log Version: 1
No Errors Logged
SMART Self-test log structure revision number 1
Num Test_Description Status Remaining LifeTime(hours) LBA_of_first_error
# 1 Extended offline Completed without error 00% 15 -
# 2 Extended offline Aborted by host 70% 10 -
# 3 Short offline Completed without error 00% 9 -
# 4 Extended offline Completed without error 00% 6 -
SMART Selective self-test log data structure revision number 1
SPAN MIN_LBA MAX_LBA CURRENT_TEST_STATUS
1 0 0 Not_testing
2 0 0 Not_testing
3 0 0 Not_testing
4 0 0 Not_testing
5 0 0 Not_testing
Selective self-test flags (0x0):
After scanning selected spans, do NOT read-scan remainder of disk.
If Selective self-test is pending on power-up, resume after 0 minute delay.
admin82@ROSSTAT-DATA-SERVER:~$
-------------------------------------------------------
3
admin82@ROSSTAT-DATA-SERVER:~$ sudo smartctl -a -d megaraid,3 /dev/sdb
smartctl 6.5 2016-01-24 r4214 [x86_64-linux-4.10.0-28-generic] (local build)
Copyright (C) 2002-16, Bruce Allen, Christian Franke, www.smartmontools.org
/dev/sdb [megaraid_disk_03] [SAT]: Device open changed type from 'megaraid,3' to 'sat+megaraid,3'
=== START OF INFORMATION SECTION ===
Model Family: Seagate Constellation ES (SATA 6Gb/s)
Device Model: ST2000NM0011
Serial Number: Z1P1X0PV
LU WWN Device Id: 5 000c50 040476f1c
Add. Product Id: DELL(tm)
Firmware Version: PA03
User Capacity: 2 000 398 934 016 bytes [2,00 TB]
Sector Size: 512 bytes logical/physical
Rotation Rate: 7202 rpm
Form Factor: 3.5 inches
Device is: In smartctl database [for details use: -P show]
ATA Version is: ATA8-ACS T13/1699-D revision 4
SATA Version is: SATA 3.0, 3.0 Gb/s (current: 3.0 Gb/s)
Local Time is: Thu Oct 31 14:16:12 2019 MSK
SMART support is: Available - device has SMART capability.
SMART support is: Enabled
=== START OF READ SMART DATA SECTION ===
SMART Status not supported: ATA return descriptor not supported by controller firmware
SMART overall-health self-assessment test result: PASSED
Warning: This result is based on an Attribute check.
General SMART Values:
Offline data collection status: (0x82) Offline data collection activity
was completed without error.
Auto Offline Data Collection: Enabled.
Self-test execution status: ( 0) The previous self-test routine completed
without error or no self-test has ever
been run.
Total time to complete Offline
data collection: ( 609) seconds.
Offline data collection
capabilities: (0x7b) SMART execute Offline immediate.
Auto Offline data collection on/off support.
Suspend Offline collection upon new
command.
Offline surface scan supported.
Self-test supported.
Conveyance Self-test supported.
Selective Self-test supported.
SMART capabilities: (0x0003) Saves SMART data before entering
power-saving mode.
Supports SMART auto save timer.
Error logging capability: (0x01) Error logging supported.
General Purpose Logging supported.
Short self-test routine
recommended polling time: ( 2) minutes.
Extended self-test routine
recommended polling time: ( 297) minutes.
Conveyance self-test routine
recommended polling time: ( 3) minutes.
SCT capabilities: (0x10bd) SCT Status supported.
SCT Error Recovery Control supported.
SCT Feature Control supported.
SCT Data Table supported.
SMART Attributes Data Structure revision number: 10
Vendor Specific SMART Attributes with Thresholds:
ID# ATTRIBUTE_NAME FLAG VALUE WORST THRESH TYPE UPDATED WHEN_FAILED RAW_VALUE
1 Raw_Read_Error_Rate 0x000f 080 063 044 Pre-fail Always - 106419492
3 Spin_Up_Time 0x0003 089 087 000 Pre-fail Always - 0
4 Start_Stop_Count 0x0032 100 100 020 Old_age Always - 90
5 Reallocated_Sector_Ct 0x0033 100 100 036 Pre-fail Always - 0
7 Seek_Error_Rate 0x000f 072 060 030 Pre-fail Always - 4310031830
9 Power_On_Hours 0x0032 075 075 000 Old_age Always - 22584
10 Spin_Retry_Count 0x0013 100 100 097 Pre-fail Always - 0
12 Power_Cycle_Count 0x0032 100 100 020 Old_age Always - 86
184 End-to-End_Error 0x0032 100 100 099 Old_age Always - 0
187 Reported_Uncorrect 0x0032 100 100 000 Old_age Always - 0
188 Command_Timeout 0x0032 100 098 000 Old_age Always - 8590065666
189 High_Fly_Writes 0x003a 100 100 000 Old_age Always - 0
190 Airflow_Temperature_Cel 0x0022 065 046 045 Old_age Always - 35 (Min/Max 21/35)
191 G-Sense_Error_Rate 0x0032 100 100 000 Old_age Always - 0
192 Power-Off_Retract_Count 0x0032 100 100 000 Old_age Always - 89
193 Load_Cycle_Count 0x0032 100 100 000 Old_age Always - 90
194 Temperature_Celsius 0x0022 035 054 000 Old_age Always - 35 (0 18 0 0 0)
195 Hardware_ECC_Recovered 0x001a 116 099 000 Old_age Always - 106419492
197 Current_Pending_Sector 0x0012 100 100 000 Old_age Always - 0
198 Offline_Uncorrectable 0x0010 100 100 000 Old_age Offline - 0
199 UDMA_CRC_Error_Count 0x003e 200 200 000 Old_age Always - 0
240 Head_Flying_Hours 0x0000 100 253 000 Old_age Offline - 8737 (233 35 0)
241 Total_LBAs_Written 0x0000 100 253 000 Old_age Offline - 2264829760
242 Total_LBAs_Read 0x0000 100 253 000 Old_age Offline - 73380404
SMART Error Log Version: 1
No Errors Logged
SMART Self-test log structure revision number 1
Num Test_Description Status Remaining LifeTime(hours) LBA_of_first_error
# 1 Extended offline Completed without error 00% 15 -
# 2 Extended offline Aborted by host 70% 10 -
# 3 Short offline Completed without error 00% 9 -
# 4 Extended offline Completed without error 00% 6 -
SMART Selective self-test log data structure revision number 1
SPAN MIN_LBA MAX_LBA CURRENT_TEST_STATUS
1 0 0 Not_testing
2 0 0 Not_testing
3 0 0 Not_testing
4 0 0 Not_testing
5 0 0 Not_testing
Selective self-test flags (0x0):
After scanning selected spans, do NOT read-scan remainder of disk.
If Selective self-test is pending on power-up, resume after 0 minute delay.
admin82@ROSSTAT-DATA-SERVER:~$
-----------------------------------------------------------------------
4
admin82@ROSSTAT-DATA-SERVER:~$ sudo smartctl -a -d megaraid,4 /dev/sdb
smartctl 6.5 2016-01-24 r4214 [x86_64-linux-4.10.0-28-generic] (local build)
Copyright (C) 2002-16, Bruce Allen, Christian Franke, www.smartmontools.org
/dev/sdb [megaraid_disk_04] [SAT]: Device open changed type from 'megaraid,4' to 'sat+megaraid,4'
=== START OF INFORMATION SECTION ===
Model Family: Seagate Constellation ES (SATA 6Gb/s)
Device Model: ST2000NM0011
Serial Number: Z1P1XT3Z
LU WWN Device Id: 5 000c50 04048a805
Add. Product Id: DELL(tm)
Firmware Version: PA03
User Capacity: 2 000 398 934 016 bytes [2,00 TB]
Sector Size: 512 bytes logical/physical
Rotation Rate: 7202 rpm
Form Factor: 3.5 inches
Device is: In smartctl database [for details use: -P show]
ATA Version is: ATA8-ACS T13/1699-D revision 4
SATA Version is: SATA 3.0, 3.0 Gb/s (current: 3.0 Gb/s)
Local Time is: Thu Oct 31 14:14:32 2019 MSK
SMART support is: Available - device has SMART capability.
SMART support is: Enabled
=== START OF READ SMART DATA SECTION ===
SMART Status not supported: ATA return descriptor not supported by controller firmware
SMART overall-health self-assessment test result: PASSED
Warning: This result is based on an Attribute check.
General SMART Values:
Offline data collection status: (0x82) Offline data collection activity
was completed without error.
Auto Offline Data Collection: Enabled.
Self-test execution status: ( 0) The previous self-test routine completed
without error or no self-test has ever
been run.
Total time to complete Offline
data collection: ( 625) seconds.
Offline data collection
capabilities: (0x7b) SMART execute Offline immediate.
Auto Offline data collection on/off support.
Suspend Offline collection upon new
command.
Offline surface scan supported.
Self-test supported.
Conveyance Self-test supported.
Selective Self-test supported.
SMART capabilities: (0x0003) Saves SMART data before entering
power-saving mode.
Supports SMART auto save timer.
Error logging capability: (0x01) Error logging supported.
General Purpose Logging supported.
Short self-test routine
recommended polling time: ( 2) minutes.
Extended self-test routine
recommended polling time: ( 304) minutes.
Conveyance self-test routine
recommended polling time: ( 3) minutes.
SCT capabilities: (0x10bd) SCT Status supported.
SCT Error Recovery Control supported.
SCT Feature Control supported.
SCT Data Table supported.
SMART Attributes Data Structure revision number: 10
Vendor Specific SMART Attributes with Thresholds:
ID# ATTRIBUTE_NAME FLAG VALUE WORST THRESH TYPE UPDATED WHEN_FAILED RAW_VALUE
1 Raw_Read_Error_Rate 0x000f 073 063 044 Pre-fail Always - 23754752
3 Spin_Up_Time 0x0003 089 089 000 Pre-fail Always - 0
4 Start_Stop_Count 0x0032 100 100 020 Old_age Always - 80
5 Reallocated_Sector_Ct 0x0033 100 100 036 Pre-fail Always - 4
7 Seek_Error_Rate 0x000f 068 060 030 Pre-fail Always - 6938911
9 Power_On_Hours 0x0032 075 075 000 Old_age Always - 22412
10 Spin_Retry_Count 0x0013 100 100 097 Pre-fail Always - 0
12 Power_Cycle_Count 0x0032 100 100 020 Old_age Always - 80
184 End-to-End_Error 0x0032 100 100 099 Old_age Always - 0
187 Reported_Uncorrect 0x0032 099 099 000 Old_age Always - 1
188 Command_Timeout 0x0032 100 099 000 Old_age Always - 4295032833
189 High_Fly_Writes 0x003a 100 100 000 Old_age Always - 0
190 Airflow_Temperature_Cel 0x0022 067 046 045 Old_age Always - 33 (Min/Max 21/33)
191 G-Sense_Error_Rate 0x0032 100 100 000 Old_age Always - 0
192 Power-Off_Retract_Count 0x0032 100 100 000 Old_age Always - 79
193 Load_Cycle_Count 0x0032 100 100 000 Old_age Always - 80
194 Temperature_Celsius 0x0022 033 054 000 Old_age Always - 33 (0 18 0 0 0)
195 Hardware_ECC_Recovered 0x001a 109 099 000 Old_age Always - 23754752
197 Current_Pending_Sector 0x0012 100 100 000 Old_age Always - 0
198 Offline_Uncorrectable 0x0010 100 100 000 Old_age Offline - 0
199 UDMA_CRC_Error_Count 0x003e 200 200 000 Old_age Always - 0
240 Head_Flying_Hours 0x0000 100 253 000 Old_age Offline - 8722 (49 72 0)
241 Total_LBAs_Written 0x0000 100 253 000 Old_age Offline - 2161783087
242 Total_LBAs_Read 0x0000 100 253 000 Old_age Offline - 609820788
SMART Error Log Version: 1
ATA Error Count: 1
CR = Command Register [HEX]
FR = Features Register [HEX]
SC = Sector Count Register [HEX]
SN = Sector Number Register [HEX]
CL = Cylinder Low Register [HEX]
CH = Cylinder High Register [HEX]
DH = Device/Head Register [HEX]
DC = Device Command Register [HEX]
ER = Error register [HEX]
ST = Status register [HEX]
Powered_Up_Time is measured from power on, and printed as
DDd+hh:mm:SS.sss where DD=days, hh=hours, mm=minutes,
SS=sec, and sss=millisec. It "wraps" after 49.710 days.
Error 1 occurred at disk power-on lifetime: 7099 hours (295 days + 19 hours)
When the command that caused the error occurred, the device was active or idle.
After command completion occurred, registers were:
ER ST SC SN CL CH DH
-- -- -- -- -- -- --
40 51 00 e0 72 72 00 Error: UNC at LBA = 0x007272e0 = 7500512
Commands leading to the command that caused the error were:
CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name
-- -- -- -- -- -- -- -- ---------------- --------------------
42 00 00 00 90 6f 40 00 1d+19:43:13.046 READ VERIFY SECTOR(S) EXT
42 00 00 00 a0 5f 40 00 1d+19:43:09.674 READ VERIFY SECTOR(S) EXT
42 00 00 00 b0 4f 40 00 1d+19:43:06.325 READ VERIFY SECTOR(S) EXT
42 00 00 00 c0 3f 40 00 1d+19:43:02.925 READ VERIFY SECTOR(S) EXT
42 00 00 00 d0 2f 40 00 1d+19:42:59.548 READ VERIFY SECTOR(S) EXT
SMART Self-test log structure revision number 1
Num Test_Description Status Remaining LifeTime(hours) LBA_of_first_error
# 1 Extended offline Completed without error 00% 15 -
# 2 Extended offline Aborted by host 80% 10 -
# 3 Short offline Completed without error 00% 9 -
# 4 Extended offline Completed without error 00% 6 -
SMART Selective self-test log data structure revision number 1
SPAN MIN_LBA MAX_LBA CURRENT_TEST_STATUS
1 0 0 Not_testing
2 0 0 Not_testing
3 0 0 Not_testing
4 0 0 Not_testing
5 0 0 Not_testing
Selective self-test flags (0x0):
After scanning selected spans, do NOT read-scan remainder of disk.
If Selective self-test is pending on power-up, resume after 0 minute delay.
admin82@ROSSTAT-DATA-SERVER:~$
-------------------------------------------------
5
admin82@ROSSTAT-DATA-SERVER:~$ sudo smartctl -a -d megaraid,5 /dev/sdb
smartctl 6.5 2016-01-24 r4214 [x86_64-linux-4.10.0-28-generic] (local build)
Copyright (C) 2002-16, Bruce Allen, Christian Franke, www.smartmontools.org
/dev/sdb [megaraid_disk_05] [SAT]: Device open changed type from 'megaraid,5' to 'sat+megaraid,5'
=== START OF INFORMATION SECTION ===
Model Family: Seagate Constellation ES (SATA 6Gb/s)
Device Model: ST2000NM0011
Serial Number: Z1P1XVMY
LU WWN Device Id: 5 000c50 04047c207
Add. Product Id: DELL(tm)
Firmware Version: PA03
User Capacity: 2 000 398 934 016 bytes [2,00 TB]
Sector Size: 512 bytes logical/physical
Rotation Rate: 7202 rpm
Form Factor: 3.5 inches
Device is: In smartctl database [for details use: -P show]
ATA Version is: ATA8-ACS T13/1699-D revision 4
SATA Version is: SATA 3.0, 3.0 Gb/s (current: 3.0 Gb/s)
Local Time is: Thu Oct 31 14:12:49 2019 MSK
SMART support is: Available - device has SMART capability.
SMART support is: Enabled
=== START OF READ SMART DATA SECTION ===
SMART Status not supported: ATA return descriptor not supported by controller firmware
SMART overall-health self-assessment test result: PASSED
Warning: This result is based on an Attribute check.
General SMART Values:
Offline data collection status: (0x82) Offline data collection activity
was completed without error.
Auto Offline Data Collection: Enabled.
Self-test execution status: ( 0) The previous self-test routine completed
without error or no self-test has ever
been run.
Total time to complete Offline
data collection: ( 617) seconds.
Offline data collection
capabilities: (0x7b) SMART execute Offline immediate.
Auto Offline data collection on/off support.
Suspend Offline collection upon new
command.
Offline surface scan supported.
Self-test supported.
Conveyance Self-test supported.
Selective Self-test supported.
SMART capabilities: (0x0003) Saves SMART data before entering
power-saving mode.
Supports SMART auto save timer.
Error logging capability: (0x01) Error logging supported.
General Purpose Logging supported.
Short self-test routine
recommended polling time: ( 2) minutes.
Extended self-test routine
recommended polling time: ( 304) minutes.
Conveyance self-test routine
recommended polling time: ( 3) minutes.
SCT capabilities: (0x10bd) SCT Status supported.
SCT Error Recovery Control supported.
SCT Feature Control supported.
SCT Data Table supported.
SMART Attributes Data Structure revision number: 10
Vendor Specific SMART Attributes with Thresholds:
ID# ATTRIBUTE_NAME FLAG VALUE WORST THRESH TYPE UPDATED WHEN_FAILED RAW_VALUE
1 Raw_Read_Error_Rate 0x000f 071 063 044 Pre-fail Always - 13916697
3 Spin_Up_Time 0x0003 089 088 000 Pre-fail Always - 0
4 Start_Stop_Count 0x0032 100 100 020 Old_age Always - 86
5 Reallocated_Sector_Ct 0x0033 100 100 036 Pre-fail Always - 0
7 Seek_Error_Rate 0x000f 071 060 030 Pre-fail Always - 13323851
9 Power_On_Hours 0x0032 075 075 000 Old_age Always - 22586
10 Spin_Retry_Count 0x0013 100 100 097 Pre-fail Always - 0
12 Power_Cycle_Count 0x0032 100 100 020 Old_age Always - 86
184 End-to-End_Error 0x0032 100 100 099 Old_age Always - 0
187 Reported_Uncorrect 0x0032 100 100 000 Old_age Always - 0
188 Command_Timeout 0x0032 100 099 000 Old_age Always - 12885098499
189 High_Fly_Writes 0x003a 100 100 000 Old_age Always - 0
190 Airflow_Temperature_Cel 0x0022 066 046 045 Old_age Always - 34 (Min/Max 20/34)
191 G-Sense_Error_Rate 0x0032 100 100 000 Old_age Always - 0
192 Power-Off_Retract_Count 0x0032 100 100 000 Old_age Always - 85
193 Load_Cycle_Count 0x0032 100 100 000 Old_age Always - 86
194 Temperature_Celsius 0x0022 034 054 000 Old_age Always - 34 (0 17 0 0 0)
195 Hardware_ECC_Recovered 0x001a 107 099 000 Old_age Always - 13916697
197 Current_Pending_Sector 0x0012 100 100 000 Old_age Always - 0
198 Offline_Uncorrectable 0x0010 100 100 000 Old_age Offline - 0
199 UDMA_CRC_Error_Count 0x003e 200 200 000 Old_age Always - 0
240 Head_Flying_Hours 0x0000 100 253 000 Old_age Offline - 8764 (43 220 0)
241 Total_LBAs_Written 0x0000 100 253 000 Old_age Offline - 2273378240
242 Total_LBAs_Read 0x0000 100 253 000 Old_age Offline - 579318284
SMART Error Log Version: 1
No Errors Logged
SMART Self-test log structure revision number 1
Num Test_Description Status Remaining LifeTime(hours) LBA_of_first_error
# 1 Extended offline Completed without error 00% 15 -
# 2 Extended offline Aborted by host 70% 10 -
# 3 Short offline Completed without error 00% 9 -
# 4 Extended offline Completed without error 00% 6 -
SMART Selective self-test log data structure revision number 1
SPAN MIN_LBA MAX_LBA CURRENT_TEST_STATUS
1 0 0 Not_testing
2 0 0 Not_testing
3 0 0 Not_testing
4 0 0 Not_testing
5 0 0 Not_testing
Selective self-test flags (0x0):
After scanning selected spans, do NOT read-scan remainder of disk.
If Selective self-test is pending on power-up, resume after 0 minute delay.
admin82@ROSSTAT-DATA-SERVER:~$
--------------------------------------------------------
6
admin82@ROSSTAT-DATA-SERVER:~$ sudo smartctl -a -d megaraid,6 /dev/sdb
smartctl 6.5 2016-01-24 r4214 [x86_64-linux-4.10.0-28-generic] (local build)
Copyright (C) 2002-16, Bruce Allen, Christian Franke, www.smartmontools.org
/dev/sdb [megaraid_disk_06] [SAT]: Device open changed type from 'megaraid,6' to 'sat+megaraid,6'
=== START OF INFORMATION SECTION ===
Model Family: Seagate Constellation ES (SATA 6Gb/s)
Device Model: ST2000NM0011
Serial Number: Z1P1X7AA
LU WWN Device Id: 5 000c50 0404742bf
Add. Product Id: DELL(tm)
Firmware Version: PA03
User Capacity: 2 000 398 934 016 bytes [2,00 TB]
Sector Size: 512 bytes logical/physical
Rotation Rate: 7202 rpm
Form Factor: 3.5 inches
Device is: In smartctl database [for details use: -P show]
ATA Version is: ATA8-ACS T13/1699-D revision 4
SATA Version is: SATA 3.0, 3.0 Gb/s (current: 3.0 Gb/s)
Local Time is: Thu Oct 31 14:11:08 2019 MSK
SMART support is: Available - device has SMART capability.
SMART support is: Enabled
=== START OF READ SMART DATA SECTION ===
SMART Status not supported: ATA return descriptor not supported by controller firmware
SMART overall-health self-assessment test result: PASSED
Warning: This result is based on an Attribute check.
General SMART Values:
Offline data collection status: (0x82) Offline data collection activity
was completed without error.
Auto Offline Data Collection: Enabled.
Self-test execution status: ( 0) The previous self-test routine completed
without error or no self-test has ever
been run.
Total time to complete Offline
data collection: ( 609) seconds.
Offline data collection
capabilities: (0x7b) SMART execute Offline immediate.
Auto Offline data collection on/off support.
Suspend Offline collection upon new
command.
Offline surface scan supported.
Self-test supported.
Conveyance Self-test supported.
Selective Self-test supported.
SMART capabilities: (0x0003) Saves SMART data before entering
power-saving mode.
Supports SMART auto save timer.
Error logging capability: (0x01) Error logging supported.
General Purpose Logging supported.
Short self-test routine
recommended polling time: ( 2) minutes.
Extended self-test routine
recommended polling time: ( 304) minutes.
Conveyance self-test routine
recommended polling time: ( 3) minutes.
SCT capabilities: (0x10bd) SCT Status supported.
SCT Error Recovery Control supported.
SCT Feature Control supported.
SCT Data Table supported.
SMART Attributes Data Structure revision number: 10
Vendor Specific SMART Attributes with Thresholds:
ID# ATTRIBUTE_NAME FLAG VALUE WORST THRESH TYPE UPDATED WHEN_FAILED RAW_VALUE
1 Raw_Read_Error_Rate 0x000f 080 063 044 Pre-fail Always - 108057248
3 Spin_Up_Time 0x0003 089 089 000 Pre-fail Always - 0
4 Start_Stop_Count 0x0032 100 100 020 Old_age Always - 86
5 Reallocated_Sector_Ct 0x0033 100 100 036 Pre-fail Always - 1
7 Seek_Error_Rate 0x000f 069 060 030 Pre-fail Always - 8971085
9 Power_On_Hours 0x0032 075 075 000 Old_age Always - 22583
10 Spin_Retry_Count 0x0013 100 100 097 Pre-fail Always - 0
12 Power_Cycle_Count 0x0032 100 100 020 Old_age Always - 86
184 End-to-End_Error 0x0032 100 100 099 Old_age Always - 0
187 Reported_Uncorrect 0x0032 100 100 000 Old_age Always - 0
188 Command_Timeout 0x0032 100 099 000 Old_age Always - 8590065666
189 High_Fly_Writes 0x003a 100 100 000 Old_age Always - 0
190 Airflow_Temperature_Cel 0x0022 068 046 045 Old_age Always - 32 (Min/Max 20/32)
191 G-Sense_Error_Rate 0x0032 100 100 000 Old_age Always - 0
192 Power-Off_Retract_Count 0x0032 100 100 000 Old_age Always - 85
193 Load_Cycle_Count 0x0032 100 100 000 Old_age Always - 86
194 Temperature_Celsius 0x0022 032 054 000 Old_age Always - 32 (0 17 0 0 0)
195 Hardware_ECC_Recovered 0x001a 116 099 000 Old_age Always - 108057248
197 Current_Pending_Sector 0x0012 100 100 000 Old_age Always - 0
198 Offline_Uncorrectable 0x0010 100 100 000 Old_age Offline - 0
199 UDMA_CRC_Error_Count 0x003e 200 200 000 Old_age Always - 0
240 Head_Flying_Hours 0x0000 100 253 000 Old_age Offline - 8732 (30 37 0)
241 Total_LBAs_Written 0x0000 100 253 000 Old_age Offline - 2256270825
242 Total_LBAs_Read 0x0000 100 253 000 Old_age Offline - 4025536990
SMART Error Log Version: 1
No Errors Logged
SMART Self-test log structure revision number 1
Num Test_Description Status Remaining LifeTime(hours) LBA_of_first_error
# 1 Extended offline Completed without error 00% 15 -
# 2 Extended offline Aborted by host 70% 10 -
# 3 Short offline Completed without error 00% 9 -
# 4 Extended offline Completed without error 00% 6 -
SMART Selective self-test log data structure revision number 1
SPAN MIN_LBA MAX_LBA CURRENT_TEST_STATUS
1 0 0 Not_testing
2 0 0 Not_testing
3 0 0 Not_testing
4 0 0 Not_testing
5 0 0 Not_testing
Selective self-test flags (0x0):
After scanning selected spans, do NOT read-scan remainder of disk.
If Selective self-test is pending on power-up, resume after 0 minute delay.
admin82@ROSSTAT-DATA-SERVER:~$
--------------------------------------------------------------------------------
7
admin82@ROSSTAT-DATA-SERVER:~$ sudo smartctl -a -d megaraid,7 /dev/sdb
smartctl 6.5 2016-01-24 r4214 [x86_64-linux-4.10.0-28-generic] (local build)
Copyright (C) 2002-16, Bruce Allen, Christian Franke, www.smartmontools.org
/dev/sdb [megaraid_disk_07] [SAT]: Device open changed type from 'megaraid,7' to 'sat+megaraid,7'
=== START OF INFORMATION SECTION ===
Model Family: Seagate Constellation ES (SATA 6Gb/s)
Device Model: ST2000NM0011
Serial Number: Z1P1WS7G
LU WWN Device Id: 5 000c50 04046bb20
Add. Product Id: DELL(tm)
Firmware Version: PA03
User Capacity: 2 000 398 934 016 bytes [2,00 TB]
Sector Size: 512 bytes logical/physical
Rotation Rate: 7202 rpm
Form Factor: 3.5 inches
Device is: In smartctl database [for details use: -P show]
ATA Version is: ATA8-ACS T13/1699-D revision 4
SATA Version is: SATA 3.0, 3.0 Gb/s (current: 3.0 Gb/s)
Local Time is: Thu Oct 31 14:07:09 2019 MSK
SMART support is: Available - device has SMART capability.
SMART support is: Enabled
=== START OF READ SMART DATA SECTION ===
SMART Status not supported: ATA return descriptor not supported by controller firmware
SMART overall-health self-assessment test result: PASSED
Warning: This result is based on an Attribute check.
General SMART Values:
Offline data collection status: (0x82) Offline data collection activity
was completed without error.
Auto Offline Data Collection: Enabled.
Self-test execution status: ( 0) The previous self-test routine completed
without error or no self-test has ever
been run.
Total time to complete Offline
data collection: ( 609) seconds.
Offline data collection
capabilities: (0x7b) SMART execute Offline immediate.
Auto Offline data collection on/off support.
Suspend Offline collection upon new
command.
Offline surface scan supported.
Self-test supported.
Conveyance Self-test supported.
Selective Self-test supported.
SMART capabilities: (0x0003) Saves SMART data before entering
power-saving mode.
Supports SMART auto save timer.
Error logging capability: (0x01) Error logging supported.
General Purpose Logging supported.
Short self-test routine
recommended polling time: ( 2) minutes.
Extended self-test routine
recommended polling time: ( 294) minutes.
Conveyance self-test routine
recommended polling time: ( 3) minutes.
SCT capabilities: (0x10bd) SCT Status supported.
SCT Error Recovery Control supported.
SCT Feature Control supported.
SCT Data Table supported.
SMART Attributes Data Structure revision number: 10
Vendor Specific SMART Attributes with Thresholds:
ID# ATTRIBUTE_NAME FLAG VALUE WORST THRESH TYPE UPDATED WHEN_FAILED RAW_VALUE
1 Raw_Read_Error_Rate 0x000f 084 063 044 Pre-fail Always - 244114530
3 Spin_Up_Time 0x0003 089 089 000 Pre-fail Always - 0
4 Start_Stop_Count 0x0032 100 100 020 Old_age Always - 86
5 Reallocated_Sector_Ct 0x0033 100 100 036 Pre-fail Always - 1
7 Seek_Error_Rate 0x000f 070 060 030 Pre-fail Always - 10802983
9 Power_On_Hours 0x0032 075 075 000 Old_age Always - 22592
10 Spin_Retry_Count 0x0013 100 100 097 Pre-fail Always - 0
12 Power_Cycle_Count 0x0032 100 100 020 Old_age Always - 86
184 End-to-End_Error 0x0032 100 100 099 Old_age Always - 0
187 Reported_Uncorrect 0x0032 100 100 000 Old_age Always - 0
188 Command_Timeout 0x0032 100 099 000 Old_age Always - 8590065666
189 High_Fly_Writes 0x003a 100 100 000 Old_age Always - 0
190 Airflow_Temperature_Cel 0x0022 066 046 045 Old_age Always - 34 (Min/Max 20/34)
191 G-Sense_Error_Rate 0x0032 100 100 000 Old_age Always - 0
192 Power-Off_Retract_Count 0x0032 100 100 000 Old_age Always - 85
193 Load_Cycle_Count 0x0032 100 100 000 Old_age Always - 86
194 Temperature_Celsius 0x0022 034 054 000 Old_age Always - 34 (0 17 0 0 0)
195 Hardware_ECC_Recovered 0x001a 120 099 000 Old_age Always - 244114530
197 Current_Pending_Sector 0x0012 100 100 000 Old_age Always - 0
198 Offline_Uncorrectable 0x0010 100 100 000 Old_age Offline - 0
199 UDMA_CRC_Error_Count 0x003e 200 200 000 Old_age Always - 0
240 Head_Flying_Hours 0x0000 100 253 000 Old_age Offline - 8719 (7 170 0)
241 Total_LBAs_Written 0x0000 100 253 000 Old_age Offline - 2443111121
242 Total_LBAs_Read 0x0000 100 253 000 Old_age Offline - 4072375595
SMART Error Log Version: 1
No Errors Logged
SMART Self-test log structure revision number 1
Num Test_Description Status Remaining LifeTime(hours) LBA_of_first_error
# 1 Extended offline Completed without error 00% 15 -
# 2 Extended offline Aborted by host 70% 10 -
# 3 Short offline Completed without error 00% 9 -
# 4 Extended offline Completed without error 00% 6 -
SMART Selective self-test log data structure revision number 1
SPAN MIN_LBA MAX_LBA CURRENT_TEST_STATUS
1 0 0 Not_testing
2 0 0 Not_testing
3 0 0 Not_testing
4 0 0 Not_testing
5 0 0 Not_testing
Selective self-test flags (0x0):
After scanning selected spans, do NOT read-scan remainder of disk.
If Selective self-test is pending on power-up, resume after 0 minute delay.
admin82@ROSSTAT-DATA-SERVER:~$
Последний раз редактировалось /dev/random 31.10.2019 19:13, всего редактировалось 1 раз.
Причина: блок code
Причина: блок code
-
Bizdelnick
- Модератор
- Сообщения: 21245
- Статус: nulla salus bello
- ОС: Debian GNU/Linux
Re: проблема с жестким диском
Сложно сказать, насколько всё в порядке или не в порядке с дисками. На многих есть по несколько перемещённых секторов (5 Reallocated_Sector_Ct), на 4 ещё какая-то ошибка в логе, но, вроде бы, ничто не указывает на то, что какой-то диск уже совсем сыпется. Надо бы всё-таки делловским софтом воспользоваться, чтобы оценить состояние массива(ов), да и вообще понять, как он собран. И посмотрите sudo dmesg — там наверняка должны быть ошибки в момент отвала.
Ну и, традиционно, проверьте/замените шлейфы.
Ну и, традиционно, проверьте/замените шлейфы.
Пишите правильно:
| в консоли вку́пе (с чем-либо) в общем вообще | в течение (часа) новичок нюанс по умолчанию | приемлемо проблема пробовать трафик |
-
userkom
- Сообщения: 5
- ОС: Linux
Re: проблема с жестким диском
Здравствуйте! Заменили raid контроллер на сервере, и всё заработало.