nut подружить с POWERCOM Imperial IMD-1500AP

[Voler]

Есть ИБП.
POWERCOM Imperial IMD-1500AP

Есть конфиг ups.conf

Код: Выделить всё

[powercom]
         driver = usbhid-ups
         port = auto
         desc "PowerCom"

При запуске, проверки работоспособности драйвера, не проходит проверку.

root@sklad:/etc/nut# upsdrvctl start
Network UPS Tools - UPS driver controller 2.4.1
Network UPS Tools - Generic HID driver 0.34 (2.4.1)
USB communication driver 0.31
No matching HID UPS found
Driver failed to start (exit status=1)

Подскажите может уже кто решал данную проблему, другие ИБП в совем хозяйстве нормально завел.

[ieleja]

http://www.networkupstools.org/compat/dev.html

попробуйте другие драивера - в "дев" ветке POWERCOM Imperial уже под "powercom" вроде ...

[Voler]

Если меняю на driver = powercom
, то в ответ
root@sklad:/etc/nut# upsdrvctl start

Network UPS Tools - UPS driver controller 2.4.1
Network UPS Tools - PowerCom protocol UPS driver 0.12 (2.4.1)

Unable to open auto: No such file or directory

Things to try:

- Check 'port=' in ups.conf

- Check owner/permissions of all parts of path

Fatal error: unusable configuration
Driver failed to start (exit status=1)

Я так понял, что данный драйвер не понимает значение auto
Меняю на /dev/usb/hiddev0

Network UPS Tools - UPS driver controller 2.4.1
Network UPS Tools - PowerCom protocol UPS driver 0.12 (2.4.1)
tcgetattr(/dev/usb/hiddev0): Invalid argument
Driver failed to start (exit status=1)

Запуск драйвера с такими параметрами /lib/nut/powercom -a powercom -u root -DDDDDD -x type=IMP -x port=/dev/ttyS0

Network UPS Tools - PowerCom protocol UPS driver 0.12 (2.4.1)
debug level is '6'
Flow control disable
Num of bytes requested for reading from UPS: 16
data receiving error (0 instead of 16 bytes)
send_to_all: SETINFO ups.mfr "PowerCom"
send_to_all: SETINFO ups.model "Unknown"
send_to_all: SETINFO ups.serial "Unknown"
send_to_all: SETINFO ups.model.type "IMP"
send_to_all: SETINFO input.voltage.nominal "230"
send_to_all: ADDCMD test.battery.start
send_to_all: ADDCMD shutdown.return
send_to_all: ADDCMD shutdown.stayoff
Num of bytes requested for reading from UPS: 16
data receiving error (0 instead of 16 bytes)
dstate_init: sock /var/run/nut/powercom-powercom open on fd 5
send_to_all: SETINFO driver.version "2.4.1"
send_to_all: SETINFO driver.version.internal "0.12"
send_to_all: SETINFO driver.name "powercom"
send_to_all: SETINFO driver.parameter.pollinterval "2"
Num of bytes requested for reading from UPS: 16
data receiving error (0 instead of 16 bytes)
Num of bytes requested for reading from UPS: 16
data receiving error (0 instead of 16 bytes)
Num of bytes requested for reading from UPS: 16
data receiving error (0 instead of 16 bytes)
Num of bytes requested for reading from UPS: 16
data receiving error (0 instead of 16 bytes)
Num of bytes requested for reading from UPS: 16

Может у кого есть идеи?