Информация о системе:
Debian GNU/Linux 5.0.8 (lenny)
kernel 2.6.26-2-686
'lspci':
Код: Выделить всё
...
04:00.0 Network controller: Intel Corporation PRO/Wireless 3945ABG [Golan] Network Connection (rev 02)
...Сначала удалось зажечь индикатор работы wi-fi адаптера, потом обнаружить необходимую сеть 'SYROVIY'.
Но подключиться к ней пока не получается.
Загрузился с Ubuntu 10.10 Live CD - сразу смог подключиться к wi-fi.
Вот что есть в /etc/network/interfaces:
Код: Выделить всё
"# This file describes the network interfaces available on your system
# and how to activate them. For more information, see interfaces(5).
# The loopback network interface
auto lo
iface lo inet loopback
# The primary network interface
# allow-hotplug eth0
# iface eth0 inet dhcp
auto wlan0
allow-hotplug wlan0
iface wlan0 inet dhcp
wpa-auth-alg OPEN
wpa-pairwise CCMP
wpa-group CCMP
wpa-psk dd86237427164637bd4cdb9a7d254187c2c81bacdb22132cc026b1c6ae924d89
wpa-driver wext
wpa-key-mgmt WPA-PSK
wpa-proto WPA2
wpa-ssid SYROVIY
iface eth0 inet dhcpСделал написанное на wiki.debian.org/iwlwifi для Lenny. Положительного эффекта не последовало.
Код: Выделить всё
sudo iwconfig:
wlan0 IEEE 802.11 ESSID:"SYROVIY"
Mode:Managed Frequency:2.412 GHz Access Point: Not-Associated
Tx-Power=15 dBm
Retry min limit:7 RTS thr:off Fragment thr=2352 B
Encryption key:off
Link Quality:0 Signal level:0 Noise level:0
Rx invalid nwid:0 Rx invalid crypt:0 Rx invalid frag:0
Tx excessive retries:0 Invalid misc:0 Missed beacon:0Код: Выделить всё
sudo iwlist wlan0 scan:
wlan0 Scan completed :
Cell 01 - Address: 90:E6:BA:D3:4C:B4
ESSID:"zagagulina"
Mode:Master
Channel:1
Frequency:2.412 GHz (Channel 1)
Quality=54/100 Signal level=-76 dBm Noise level=-127 dBm
Encryption key:off
Bit Rates:1 Mb/s; 2 Mb/s; 5.5 Mb/s; 11 Mb/s; 9 Mb/s
18 Mb/s; 36 Mb/s; 54 Mb/s; 6 Mb/s; 12 Mb/s
24 Mb/s; 48 Mb/s
Extra:tsf=0000008ceaaec13f
Cell 02 - Address: 00:17:31:1B:03:30
ESSID:"gr_432"
Mode:Master
Channel:1
Frequency:2.412 GHz (Channel 1)
Quality=55/100 Signal level=-75 dBm Noise level=-127 dBm
Encryption key:on
IE: IEEE 802.11i/WPA2 Version 1
Group Cipher : TKIP
Pairwise Ciphers (1) : TKIP
Authentication Suites (1) : PSK
Bit Rates:1 Mb/s; 2 Mb/s; 5.5 Mb/s; 11 Mb/s; 18 Mb/s
24 Mb/s; 36 Mb/s; 54 Mb/s; 6 Mb/s; 9 Mb/s
12 Mb/s; 48 Mb/s
Extra:tsf=0000002e0c804f79
Cell 03 - Address: 1C:BD:B9:C1:04:82
ESSID:"SYROVIY"
Mode:Master
Channel:3
Frequency:2.422 GHz (Channel 3)
Quality=46/100 Signal level=-81 dBm Noise level=-127 dBm
Encryption key:on
IE: WPA Version 1
Group Cipher : TKIP
Pairwise Ciphers (2) : CCMP TKIP
Authentication Suites (1) : PSK
IE: IEEE 802.11i/WPA2 Version 1
Group Cipher : TKIP
Pairwise Ciphers (2) : CCMP TKIP
Authentication Suites (1) : PSK
Bit Rates:1 Mb/s; 2 Mb/s; 5.5 Mb/s; 11 Mb/s; 9 Mb/s
18 Mb/s; 36 Mb/s; 54 Mb/s; 6 Mb/s; 12 Mb/s
24 Mb/s; 48 Mb/s
Extra:tsf=0000008b0653da29К 'Cell 03' нужно подключиться. Через network-manager это сделать пока не удалось.
P.S.: Если поможет, вот dmesg | less:
Код: Выделить всё
[ 0.000000] Initializing cgroup subsys cpuset
[ 0.000000] Initializing cgroup subsys cpu
[ 0.000000] Linux version 2.6.26-2-686 (Debian 2.6.26-26lenny2) (dannf@debian.org) (gcc version 4.1.3 20080704 (prerelease) (Debian 4.1.2-25)) #1 SMP Thu Jan 27 00:28:05 UTC 2011
[ 0.000000] BIOS-provided physical RAM map:
[ 0.000000] BIOS-e820: 0000000000000000 - 000000000009f800 (usable)
[ 0.000000] BIOS-e820: 000000000009f800 - 00000000000a0000 (reserved)
[ 0.000000] BIOS-e820: 00000000000e0000 - 0000000000100000 (reserved)
[ 0.000000] BIOS-e820: 0000000000100000 - 000000003fed0000 (usable)
[ 0.000000] BIOS-e820: 000000003fed0000 - 000000003fedf000 (ACPI NVS)
[ 0.000000] BIOS-e820: 000000003fedf000 - 0000000040000000 (reserved)
[ 0.000000] BIOS-e820: 00000000e0000000 - 00000000f0000000 (reserved)
[ 0.000000] BIOS-e820: 00000000fec00000 - 00000000fec10000 (reserved)
[ 0.000000] BIOS-e820: 00000000fed00000 - 00000000fed00400 (reserved)
[ 0.000000] BIOS-e820: 00000000fed14000 - 00000000fed1a000 (reserved)
[ 0.000000] BIOS-e820: 00000000fed1c000 - 00000000fed90000 (reserved)
[ 0.000000] BIOS-e820: 00000000fee00000 - 00000000fee01000 (reserved)
[ 0.000000] BIOS-e820: 00000000ff000000 - 0000000100000000 (reserved)
[ 0.000000] 126MB HIGHMEM available.
[ 0.000000] 896MB LOWMEM available.
[ 0.000000] found SMP MP-table at [c00f7d60] 000f7d60
[ 0.000000] Entering add_active_range(0, 0, 261840) 0 entries of 256 used
[ 0.000000] Zone PFN ranges:
[ 0.000000] DMA 0 -> 4096
[ 0.000000] Normal 4096 -> 229376
[ 0.000000] HighMem 229376 -> 261840
[ 0.000000] Movable zone start PFN for each node
[ 0.000000] early_node_map[1] active PFN ranges
[ 0.000000] 0: 0 -> 261840
[ 0.000000] On node 0 totalpages: 261840
[ 0.000000] DMA zone: 32 pages used for memmap
[ 0.000000] DMA zone: 0 pages reserved
[ 0.000000] DMA zone: 4064 pages, LIFO batch:0
[ 0.000000] Normal zone: 1760 pages used for memmap
[ 0.000000] Normal zone: 223520 pages, LIFO batch:31
[ 0.000000] HighMem zone: 254 pages used for memmap
[ 0.000000] HighMem zone: 32210 pages, LIFO batch:7
[ 0.000000] Movable zone: 0 pages used for memmap
[ 0.000000] DMI present.
[ 0.000000] ACPI: RSDP 000F7BF0, 0024 (r2 PTLTD )
[ 0.000000] ACPI: XSDT 3FED1778, 008C (r1 ACRSYS ACRPRDCT 6040000 INNA 0)
[ 0.000000] ACPI: FACP 3FEDBBD7, 00F4 (r3 INTEL CRESTLNE 6040000 ALAN 1)
[ 0.000000] ACPI: DSDT 3FED2BEC, 8F77 (r2 INTEL CRESTLNE 6040000 MSFT 3000000)
[ 0.000000] ACPI: FACS 3FEDEFC0, 0040
[ 0.000000] ACPI: HPET 3FEDBCCB, 0038 (r1 INTEL CRESTLNE 6040000 LOHR 5A)
[ 0.000000] ACPI: MCFG 3FEDBD03, 003C (r1 INTEL CRESTLNE 6040000 LOHR 5A)
[ 0.000000] ACPI: TCPA 3FEDBD3F, 0032 (r1 Intel CRESTLN 6040000 5A52)
[ 0.000000] ACPI: TMOR 3FEDBD71, 0026 (r1 PTLTD 6040000 PTL 3)
[ 0.000000] ACPI: SLIC 3FEDBD97, 0176 (r1 ACRSYS ACRPRDCT 6040000 ANNI 1)
[ 0.000000] ACPI: ASF! 3FEDBF0D, 0063 (r32 OEMID OEMTBL 6040000 PTL 1)
[ 0.000000] ACPI: APIC 3FEDBF70, 0068 (r1 PTLTD APIC 6040000 LTP 0)
[ 0.000000] ACPI: BOOT 3FEDBFD8, 0028 (r1 PTLTD $SBFTBL$ 6040000 LTP 1)
[ 0.000000] ACPI: SSDT 3FED290F, 02DD (r1 SataRe SataAhci 1000 INTL 20050624)
[ 0.000000] ACPI: SSDT 3FED1D90, 025F (r1 PmRef Cpu0Tst 3000 INTL 20050624)
[ 0.000000] ACPI: SSDT 3FED1CEA, 00A6 (r1 PmRef Cpu1Tst 3000 INTL 20050624)
[ 0.000000] ACPI: SSDT 3FED1804, 04E6 (r1 PmRef CpuPm 3000 INTL 20050624)
[ 0.000000] ACPI: DMI detected: Acer
[ 0.000000] ACPI: PM-Timer IO Port: 0x1008
[ 0.000000] ACPI: Local APIC address 0xfee00000
[ 0.000000] ACPI: LAPIC (acpi_id[0x00] lapic_id[0x00] enabled)
[ 0.000000] ACPI: LAPIC (acpi_id[0x01] lapic_id[0x01] enabled)
[ 0.000000] ACPI: LAPIC_NMI (acpi_id[0x00] high edge lint[0x1])
[ 0.000000] ACPI: LAPIC_NMI (acpi_id[0x01] high edge lint[0x1])
[ 0.000000] ACPI: IOAPIC (id[0x02] address[0xfec00000] gsi_base[0])
[ 0.000000] IOAPIC[0]: apic_id 2, version 32, address 0xfec00000, GSI 0-23
[ 0.000000] ACPI: INT_SRC_OVR (bus 0 bus_irq 0 global_irq 2 high edge)
[ 0.000000] ACPI: INT_SRC_OVR (bus 0 bus_irq 9 global_irq 9 high level)
[ 0.000000] ACPI: IRQ0 used by override.
[ 0.000000] ACPI: IRQ2 used by override.
[ 0.000000] ACPI: IRQ9 used by override.
[ 0.000000] Enabling APIC mode: Flat. Using 1 I/O APICs
[ 0.000000] ACPI: HPET id: 0x8086a201 base: 0xfed00000
[ 0.000000] Using ACPI (MADT) for SMP configuration information
[ 0.000000] Allocating PCI resources starting at 50000000 (gap: 40000000:a0000000)
[ 0.000000] PM: Registered nosave memory: 000000000009f000 - 00000000000a0000
[ 0.000000] PM: Registered nosave memory: 00000000000a0000 - 00000000000e0000
[ 0.000000] PM: Registered nosave memory: 00000000000e0000 - 0000000000100000
[ 0.000000] SMP: Allowing 2 CPUs, 0 hotplug CPUs
[ 0.000000] PERCPU: Allocating 37992 bytes of per cpu data
[ 0.000000] NR_CPUS: 8, nr_cpu_ids: 2
[ 0.000000] Built 1 zonelists in Zone order, mobility grouping on. Total pages: 259794
[ 0.000000] Kernel command line: root=UUID=8b6e5a1c-2880-4443-b529-29c906370bce ro
[ 0.000000] mapped APIC to ffffb000 (fee00000)
[ 0.000000] mapped IOAPIC to ffffa000 (fec00000)
[ 0.000000] Enabling fast FPU save and restore... done.
[ 0.000000] Enabling unmasked SIMD FPU exception support... done.
[ 0.000000] Initializing CPU#0
[ 0.000000] PID hash table entries: 4096 (order: 12, 16384 bytes)
[ 0.000000] Extended CMOS year: 2000
[ 0.000000] Detected 1496.336 MHz processor.
[ 0.004000] Console: colour VGA+ 80x25
[ 0.004000] console [tty0] enabled
[ 0.004000] Dentry cache hash table entries: 131072 (order: 7, 524288 bytes)
[ 0.004000] Inode-cache hash table entries: 65536 (order: 6, 262144 bytes)
[ 0.004000] Memory: 1028324k/1047360k available (1772k kernel code, 18404k reserved, 749k data, 244k init, 129856k highmem)
[ 0.004000] virtual kernel memory layout:
[ 0.004000] fixmap : 0xfff4c000 - 0xfffff000 ( 716 kB)
[ 0.004000] pkmap : 0xff800000 - 0xffc00000 (4096 kB)
[ 0.004000] vmalloc : 0xf8800000 - 0xff7fe000 ( 111 MB)
[ 0.004000] lowmem : 0xc0000000 - 0xf8000000 ( 896 MB)
[ 0.004000] .init : 0xc037f000 - 0xc03bc000 ( 244 kB)
[ 0.004000] .data : 0xc02bb06d - 0xc0376620 ( 749 kB)
[ 0.004000] .text : 0xc0100000 - 0xc02bb06d (1772 kB)
[ 0.004000] Checking if this processor honours the WP bit even in supervisor mode...Ok.
[ 0.004000] CPA: page pool initialized 1 of 1 pages preallocated
[ 0.004000] hpet clockevent registered
[ 0.083951] Calibrating delay using timer specific routine.. 2996.55 BogoMIPS (lpj=5993107)
[ 0.084005] Security Framework initialized
[ 0.084005] SELinux: Disabled at boot.
[ 0.084005] Capability LSM initialized
[ 0.084005] Mount-cache hash table entries: 512
[ 0.084005] Initializing cgroup subsys ns
[ 0.084005] Initializing cgroup subsys cpuacct
[ 0.084005] Initializing cgroup subsys devices
[ 0.084005] CPU: L1 I cache: 32K, L1 D cache: 32K
[ 0.084005] CPU: L2 cache: 2048K
[ 0.084005] CPU: Physical Processor ID: 0
[ 0.084005] CPU: Processor Core ID: 0
[ 0.084005] Intel machine check architecture supported.
[ 0.084005] Intel machine check reporting enabled on CPU#0.
[ 0.084005] using mwait in idle threads.
[ 0.084005] Checking 'hlt' instruction... OK.
[ 0.100006] ACPI: Core revision 20080321
[ 0.116007] ENABLING IO-APIC IRQs
[ 0.116007] ..TIMER: vector=0x31 apic1=0 pin1=2 apic2=-1 pin2=-1
[ 0.155815] CPU0: Intel(R) Core(TM)2 Duo CPU T5250 @ 1.50GHz stepping 0d
[ 0.156009] Booting processor 1/1 ip 6000
[ 0.164010] Initializing CPU#1
[ 0.164010] Calibrating delay using timer specific routine.. 2992.44 BogoMIPS (lpj=5984892)
[ 0.164010] CPU: L1 I cache: 32K, L1 D cache: 32K
[ 0.164010] CPU: L2 cache: 2048K
[ 0.164010] CPU: Physical Processor ID: 0
[ 0.164010] CPU: Processor Core ID: 1
[ 0.164010] Intel machine check architecture supported.
[ 0.164010] Intel machine check reporting enabled on CPU#1.
[ 0.244015] CPU1: Intel(R) Core(TM)2 Duo CPU T5250 @ 1.50GHz stepping 0d
[ 0.244015] checking TSC synchronization [CPU#0 -> CPU#1]: passed.
[ 0.248015] Brought up 2 CPUs
[ 0.248015] Total of 2 processors activated (5988.99 BogoMIPS).
[ 0.248015] CPU0 attaching sched-domain:
[ 0.248015] domain 0: span 0-1
[ 0.248015] groups: 0 1
[ 0.248015] CPU1 attaching sched-domain:
[ 0.248015] domain 0: span 0-1
[ 0.248015] groups: 1 0
[ 0.248015] net_namespace: 660 bytes
[ 0.248015] Booting paravirtualized kernel on bare hardware
[ 0.248015] NET: Registered protocol family 16
[ 0.248015] ACPI: bus type pci registered
[ 0.248015] PCI: MCFG configuration 0: base e0000000 segment 0 buses 0 - 255
[ 0.248015] PCI: MCFG area at e0000000 reserved in E820
[ 0.248015] PCI: Using MMCONFIG for extended config space
[ 0.248015] PCI: Using configuration type 1 for base access
[ 0.248015] Setting up standard PCI resources
[ 0.252015] ACPI: EC: Look up EC in DSDT
[ 0.256016] ACPI: BIOS _OSI(Linux) query ignored via DMI
[ 0.256016] ACPI: Interpreter enabled
[ 0.256094] ACPI: (supports S0 S3 S4 S5)
[ 0.256450] ACPI: Using IOAPIC for interrupt routing
[ 0.256016] ACPI: EC: non-query interrupt received, switching to interrupt mode
[ 0.311482] ACPI: EC: GPE = 0x17, I/O: command/status = 0x66, data = 0x62
[ 0.311482] ACPI: EC: driver started in interrupt mode
[ 0.311482] ACPI: PCI Root Bridge [PCI0] (0000:00)
[ 0.312293] pci 0000:00:1f.0: quirk: region 1000-107f claimed by ICH6 ACPI/GPIO/TCO
[ 0.312380] pci 0000:00:1f.0: quirk: region 1180-11bf claimed by ICH6 GPIO
[ 0.316889] PCI: Transparent bridge - 0000:00:1e.0
[ 0.316889] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0._PRT]
[ 0.316889] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.PEGP._PRT]
[ 0.316889] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.RP01._PRT]
[ 0.316889] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.RP02._PRT]
[ 0.316889] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.RP03._PRT]
[ 0.316889] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.PCIB._PRT]
[ 0.333669] ACPI: PCI Interrupt Link [LNKA] (IRQs 10 *11)
[ 0.333669] ACPI: PCI Interrupt Link [LNKB] (IRQs 10 *11)
[ 0.333805] ACPI: PCI Interrupt Link [LNKC] (IRQs 10 *11)
[ 0.334259] ACPI: PCI Interrupt Link [LNKD] (IRQs 10 *11)
[ 0.334708] ACPI: PCI Interrupt Link [LNKE] (IRQs 10 *11)
[ 0.335158] ACPI: PCI Interrupt Link [LNKF] (IRQs 10 *11)
[ 0.335610] ACPI: PCI Interrupt Link [LNKG] (IRQs 10 *11)
[ 0.336058] ACPI: PCI Interrupt Link [LNKH] (IRQs 10 *11)
[ 0.337427] Linux Plug and Play Support v0.97 (c) Adam Belay
[ 0.337427] pnp: PnP ACPI init
[ 0.337427] ACPI: bus type pnp registered
[ 0.348293] pnp: PnP ACPI: found 11 devices
[ 0.348293] ACPI: ACPI bus type pnp unregistered
[ 0.348293] PnPBIOS: Disabled by ACPI PNP
[ 0.348293] PCI: Using ACPI for IRQ routing
[ 0.351010] hpet0: at MMIO 0xfed00000, IRQs 2, 8, 0
[ 0.351361] hpet0: 3 64-bit timers, 14318180 Hz
[ 0.352293] ACPI: RTC can wake from S4
[ 0.358727] system 00:01: iomem range 0xfed1c000-0xfed1ffff could not be reserved
[ 0.358827] system 00:01: iomem range 0xfed14000-0xfed17fff could not be reserved
[ 0.358929] system 00:01: iomem range 0xfed18000-0xfed18fff could not be reserved
[ 0.359014] system 00:01: iomem range 0xfed19000-0xfed19fff could not be reserved
[ 0.360196] system 00:01: iomem range 0xe0000000-0xefffffff could not be reserved
[ 0.360282] system 00:01: iomem range 0xfed20000-0xfed3ffff could not be reserved
[ 0.360294] system 00:01: iomem range 0xfed45000-0xfed8ffff could not be reserved
[ 0.360294] system 00:06: iomem range 0xfed00000-0xfed003ff could not be reserved
[ 0.360294] system 00:08: ioport range 0x680-0x69f has been reserved
[ 0.360294] system 00:08: ioport range 0x800-0x80f has been reserved
[ 0.360294] system 00:08: ioport range 0x1000-0x107f has been reserved
[ 0.360294] system 00:08: ioport range 0x1180-0x11bf has been reserved
[ 0.360294] system 00:08: ioport range 0xfe00-0xfe00 has been reserved
[ 0.360294] system 00:08: iomem range 0xff800000-0xff800fff could not be reserved
[ 0.393481] PCI: region 0000:0f:06.0/9 too large: 0x0000000000000000-0x0000000003ffffff
[ 0.393576] PCI: Bridge: 0000:00:01.0
[ 0.393649] IO window: 2000-2fff
[ 0.393727] MEM window: 0xfc000000-0xfc0fffff
[ 0.393821] PREFETCH window: 0x00000000d0000000-0x00000000dfffffff
[ 0.393900] PCI: Bridge: 0000:00:1c.0
[ 0.393973] IO window: 3000-3fff
[ 0.394051] MEM window: 0xf6000000-0xf7ffffff
[ 0.394127] PREFETCH window: 0x00000000f0000000-0x00000000f1ffffff
[ 0.394209] PCI: Bridge: 0000:00:1c.1
[ 0.396658] IO window: 4000-4fff
[ 0.396734] MEM window: 0xf8000000-0xf9ffffff
[ 0.396812] PREFETCH window: 0x00000000f2000000-0x00000000f3ffffff
[ 0.396894] PCI: Bridge: 0000:00:1c.2
[ 0.396967] IO window: 5000-5fff
[ 0.397045] MEM window: 0xfa000000-0xfbffffff
[ 0.397146] PREFETCH window: 0x00000000f4000000-0x00000000f5ffffff
[ 0.397231] PCI: Bus 16, cardbus bridge: 0000:0f:06.0
[ 0.397305] IO window: 0x00006000-0x000060ff
[ 0.397381] IO window: 0x00006400-0x000064ff
[ 0.397459] MEM window: 0x54000000-0x57ffffff
[ 0.397535] PCI: Bridge: 0000:00:1e.0
[ 0.397609] IO window: 6000-6fff
[ 0.397686] MEM window: 0xfc100000-0xfc1fffff
[ 0.397762] PREFETCH window: disabled.
[ 0.397804] ACPI: PCI Interrupt 0000:00:01.0[A] -> GSI 16 (level, low) -> IRQ 16
[ 0.397804] PCI: Setting latency timer of device 0000:00:01.0 to 64
[ 0.397804] ACPI: PCI Interrupt 0000:00:1c.0[A] -> GSI 16 (level, low) -> IRQ 16
[ 0.397804] PCI: Setting latency timer of device 0000:00:1c.0 to 64
[ 0.397804] ACPI: PCI Interrupt 0000:00:1c.1[B] -> GSI 17 (level, low) -> IRQ 17
[ 0.397804] PCI: Setting latency timer of device 0000:00:1c.1 to 64
[ 0.397804] ACPI: PCI Interrupt 0000:00:1c.2[C] -> GSI 18 (level, low) -> IRQ 18
[ 0.397804] PCI: Setting latency timer of device 0000:00:1c.2 to 64
[ 0.397804] PCI: Setting latency timer of device 0000:00:1e.0 to 64
[ 0.397804] ACPI: PCI Interrupt 0000:0f:06.0[A] -> GSI 22 (level, low) -> IRQ 22
[ 0.397804] NET: Registered protocol family 2
[ 0.410041] IP route cache hash table entries: 32768 (order: 5, 131072 bytes)
[ 0.410424] TCP established hash table entries: 131072 (order: 8, 1048576 bytes)
[ 0.410976] TCP bind hash table entries: 65536 (order: 7, 524288 bytes)
[ 0.411300] TCP: Hash tables configured (established 131072 bind 65536)
[ 0.411376] TCP reno registered
[ 0.414053] NET: Registered protocol family 1
[ 0.414265] checking if image is initramfs...<7>Switched to high resolution mode on CPU 1
[ 0.513910] Switched to high resolution mode on CPU 0
[ 0.717787] it is
[ 1.041802] Freeing initrd memory: 6070k freed
[ 1.041802] Simple Boot Flag at 0x36 set to 0x1
[ 1.042366] audit: initializing netlink socket (disabled)
[ 1.042366] type=2000 audit(1299606032.032:1): initialized
[ 1.042366] highmem bounce pool size: 64 pages
[ 1.042366] Total HugeTLB memory allocated, 0
[ 1.042366] VFS: Disk quotas dquot_6.5.1
[ 1.042366] Dquot-cache hash table entries: 1024 (order 0, 4096 bytes)
[ 1.042366] msgmni has been set to 1767
[ 1.044450] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 253)
[ 1.044537] io scheduler noop registered
[ 1.044610] io scheduler anticipatory registered
[ 1.044683] io scheduler deadline registered
[ 1.044768] io scheduler cfq registered (default)
[ 1.045018] pci 0000:01:00.0: Boot video device
[ 1.046362] PCI: Setting latency timer of device 0000:00:01.0 to 64
[ 1.046362] assign_interrupt_mode Found MSI capability
[ 1.046362] Allocate Port Service[0000:00:01.0:pcie00]
[ 1.046362] Allocate Port Service[0000:00:01.0:pcie02]
[ 1.046362] Allocate Port Service[0000:00:01.0:pcie03]
[ 1.046362] PCI: Setting latency timer of device 0000:00:1c.0 to 64
[ 1.046362] assign_interrupt_mode Found MSI capability
[ 1.046362] Allocate Port Service[0000:00:1c.0:pcie00]
[ 1.046362] Allocate Port Service[0000:00:1c.0:pcie02]
[ 1.046362] Allocate Port Service[0000:00:1c.0:pcie03]
[ 1.046362] PCI: Setting latency timer of device 0000:00:1c.1 to 64
[ 1.046362] assign_interrupt_mode Found MSI capability
[ 1.046362] Allocate Port Service[0000:00:1c.1:pcie00]
[ 1.046362] Allocate Port Service[0000:00:1c.1:pcie02]
[ 1.046362] Allocate Port Service[0000:00:1c.1:pcie03]
[ 1.046362] PCI: Setting latency timer of device 0000:00:1c.2 to 64
[ 1.046362] assign_interrupt_mode Found MSI capability
[ 1.046362] Allocate Port Service[0000:00:1c.2:pcie00]
[ 1.046362] Allocate Port Service[0000:00:1c.2:pcie02]
[ 1.046362] Allocate Port Service[0000:00:1c.2:pcie03]
[ 1.046362] isapnp: Scanning for PnP cards...
[ 1.406563] isapnp: No Plug & Play device found
[ 1.409941] hpet_resources: 0xfed00000 is busy
[ 1.409941] Serial: 8250/16550 driver $Revision: 1.90 $ 4 ports, IRQ sharing enabled
[ 1.411867] brd: module loaded
[ 1.412078] PNP: PS/2 Controller [PNP0303:KBD0,PNP0f13:PS2M] at 0x60,0x64 irq 1,12
[ 1.422443] i8042.c: Detected active multiplexing controller, rev 1.1.
[ 1.430437] serio: i8042 KBD port at 0x60,0x64 irq 1
[ 1.430548] serio: i8042 AUX0 port at 0x60,0x64 irq 12
[ 1.430657] serio: i8042 AUX1 port at 0x60,0x64 irq 12
[ 1.430769] serio: i8042 AUX2 port at 0x60,0x64 irq 12
[ 1.430878] serio: i8042 AUX3 port at 0x60,0x64 irq 12
[ 1.432786] mice: PS/2 mouse device common for all mice
[ 1.432786] rtc_cmos 00:09: rtc core: registered rtc_cmos as rtc0
[ 1.432786] rtc0: alarms up to one month, y3k
[ 1.432786] cpuidle: using governor ladder
[ 1.432786] cpuidle: using governor menu
[ 1.432786] No iBFT detected.
[ 1.432786] TCP cubic registered
[ 1.432786] NET: Registered protocol family 17
[ 1.432786] Using IPI No-Shortcut mode
[ 1.432786] registered taskstats version 1
[ 1.432786] rtc_cmos 00:09: setting system clock to 2011-03-08 17:40:32 UTC (1299606032)
[ 1.433051] Freeing unused kernel memory: 244k freed
[ 1.453939] input: AT Translated Set 2 keyboard as /class/input/input0
[ 1.537744] ACPI: SSDT 3FED2693, 01B4 (r1 PmRef Cpu0Ist 3000 INTL 20050624)
[ 1.537744] ACPI: SSDT 3FED1FEF, 061F (r1 PmRef Cpu0Cst 3001 INTL 20050624)
[ 1.540721] Monitor-Mwait will be used to enter C-1 state
[ 1.540725] Monitor-Mwait will be used to enter C-2 state
[ 1.540728] Monitor-Mwait will be used to enter C-3 state
[ 1.541744] ACPI: CPU0 (power states: C1[C1] C2[C2] C3[C3])
[ 1.541744] ACPI: ACPI0007:00 is registered as cooling_device0
[ 1.541744] ACPI: Processor [CPU0] (supports 8 throttling states)
[ 1.541744] ACPI: SSDT 3FED2847, 00C8 (r1 PmRef Cpu1Ist 3000 INTL 20050624)
[ 1.541744] ACPI: SSDT 3FED260E, 0085 (r1 PmRef Cpu1Cst 3000 INTL 20050624)
[ 1.541744] Marking TSC unstable due to: TSC halts in idle.
[ 1.546276] ACPI: CPU1 (power states: C1[C1] C2[C2] C3[C3])
[ 1.548200] ACPI: ACPI0007:01 is registered as cooling_device1
[ 1.548316] ACPI: Processor [CPU1] (supports 8 throttling states)
[ 1.923542] ACPI: LNXTHERM:01 is registered as thermal_zone0
[ 1.923542] ACPI: Thermal Zone [TZS0] (68 C)
[ 1.935811] ACPI: LNXTHERM:02 is registered as thermal_zone1
[ 1.937061] ACPI: Thermal Zone [TZS1] (71 C)
[ 2.070575] Clocksource tsc unstable (delta = -247772612 ns)
[ 2.273989] usbcore: registered new interface driver usbfs
[ 2.273989] usbcore: registered new interface driver hub
[ 2.273989] usbcore: registered new device driver usb
[ 2.273989] USB Universal Host Controller Interface driver v3.0
[ 2.273989] ACPI: PCI Interrupt 0000:00:1a.0[A] -> GSI 20 (level, low) -> IRQ 20
[ 2.273989] PCI: Setting latency timer of device 0000:00:1a.0 to 64
[ 2.273989] uhci_hcd 0000:00:1a.0: UHCI Host Controller
[ 2.273989] uhci_hcd 0000:00:1a.0: new USB bus registered, assigned bus number 1
[ 2.273989] uhci_hcd 0000:00:1a.0: irq 20, io base 0x00001800
[ 2.273989] usb usb1: configuration #1 chosen from 1 choice
[ 2.273989] hub 1-0:1.0: USB hub found
[ 2.273989] hub 1-0:1.0: 2 ports detected
[ 2.361987] No dock devices found.
[ 2.374694] usb usb1: New USB device found, idVendor=1d6b, idProduct=0001
[ 2.374808] usb usb1: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[ 2.374927] usb usb1: Product: UHCI Host Controller
[ 2.375034] usb usb1: Manufacturer: Linux 2.6.26-2-686 uhci_hcd
[ 2.375145] usb usb1: SerialNumber: 0000:00:1a.0
[ 2.377335] ACPI: PCI Interrupt 0000:00:1a.1[B] -> GSI 21 (level, low) -> IRQ 21
[ 2.377571] PCI: Setting latency timer of device 0000:00:1a.1 to 64
[ 2.377578] uhci_hcd 0000:00:1a.1: UHCI Host Controller
[ 2.377717] uhci_hcd 0000:00:1a.1: new USB bus registered, assigned bus number 2
[ 2.377892] uhci_hcd 0000:00:1a.1: irq 21, io base 0x00001820
[ 2.377951] usb usb2: configuration #1 chosen from 1 choice
[ 2.377951] hub 2-0:1.0: USB hub found
[ 2.377951] hub 2-0:1.0: 2 ports detected
[ 2.377987] SCSI subsystem initialized
[ 2.393987] libata version 3.00 loaded.
[ 2.445994] sdhci: Secure Digital Host Controller Interface driver
[ 2.445994] sdhci: Copyright(c) Pierre Ossman
[ 2.478137] usb usb2: New USB device found, idVendor=1d6b, idProduct=0001
[ 2.478257] usb usb2: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[ 2.478377] usb usb2: Product: UHCI Host Controller
[ 2.478487] usb usb2: Manufacturer: Linux 2.6.26-2-686 uhci_hcd
[ 2.478604] usb usb2: SerialNumber: 0000:00:1a.1
[ 2.481994] ACPI: PCI Interrupt 0000:00:1a.7[C] -> GSI 20 (level, low) -> IRQ 20
[ 2.481994] PCI: Setting latency timer of device 0000:00:1a.7 to 64
[ 2.481994] ehci_hcd 0000:00:1a.7: EHCI Host Controller
[ 2.481994] ehci_hcd 0000:00:1a.7: new USB bus registered, assigned bus number 3
[ 2.485994] ehci_hcd 0000:00:1a.7: debug port 1
[ 2.485994] PCI: cache line size of 32 is not supported by device 0000:00:1a.7
[ 2.485994] ehci_hcd 0000:00:1a.7: irq 20, io mem 0xfc404800
[ 2.498035] ehci_hcd 0000:00:1a.7: USB 2.0 started, EHCI 1.00, driver 10 Dec 2004
[ 2.498242] usb usb3: configuration #1 chosen from 1 choice
[ 2.498382] hub 3-0:1.0: USB hub found
[ 2.499562] hub 3-0:1.0: 4 ports detected
[ 2.603297] usb usb3: New USB device found, idVendor=1d6b, idProduct=0002
[ 2.603423] usb usb3: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[ 2.603538] usb usb3: Product: EHCI Host Controller
[ 2.605263] usb usb3: Manufacturer: Linux 2.6.26-2-686 ehci_hcd
[ 2.605263] usb usb3: SerialNumber: 0000:00:1a.7
[ 2.606222] ACPI: PCI Interrupt 0000:00:1d.0[A] -> GSI 23 (level, low) -> IRQ 23
[ 2.606222] PCI: Setting latency timer of device 0000:00:1d.0 to 64
[ 2.606222] uhci_hcd 0000:00:1d.0: UHCI Host Controller
[ 2.606222] uhci_hcd 0000:00:1d.0: new USB bus registered, assigned bus number 4
[ 2.606222] uhci_hcd 0000:00:1d.0: irq 23, io base 0x00001840
[ 2.606222] usb usb4: configuration #1 chosen from 1 choice
[ 2.606222] hub 4-0:1.0: USB hub found
[ 2.606222] hub 4-0:1.0: 2 ports detected
[ 2.707305] usb usb4: New USB device found, idVendor=1d6b, idProduct=0001
[ 2.707428] usb usb4: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[ 2.707544] usb usb4: Product: UHCI Host Controller
[ 2.707649] usb usb4: Manufacturer: Linux 2.6.26-2-686 uhci_hcd
[ 2.707755] usb usb4: SerialNumber: 0000:00:1d.0
[ 2.709266] ACPI: PCI Interrupt 0000:00:1d.1[B] -> GSI 17 (level, low) -> IRQ 17
[ 2.709396] PCI: Setting latency timer of device 0000:00:1d.1 to 64
[ 2.709403] uhci_hcd 0000:00:1d.1: UHCI Host Controller
[ 2.709533] uhci_hcd 0000:00:1d.1: new USB bus registered, assigned bus number 5
[ 2.709692] uhci_hcd 0000:00:1d.1: irq 17, io base 0x00001860
[ 2.709880] usb usb5: configuration #1 chosen from 1 choice
[ 2.710016] hub 5-0:1.0: USB hub found
[ 2.710126] hub 5-0:1.0: 2 ports detected
[ 2.811182] usb usb5: New USB device found, idVendor=1d6b, idProduct=0001
[ 2.811305] usb usb5: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[ 2.811422] usb usb5: Product: UHCI Host Controller
[ 2.811527] usb usb5: Manufacturer: Linux 2.6.26-2-686 uhci_hcd
[ 2.811635] usb usb5: SerialNumber: 0000:00:1d.1
[ 2.813223] ACPI: PCI Interrupt 0000:00:1d.2[C] -> GSI 18 (level, low) -> IRQ 18
[ 2.813353] PCI: Setting latency timer of device 0000:00:1d.2 to 64
[ 2.813360] uhci_hcd 0000:00:1d.2: UHCI Host Controller
[ 2.813493] uhci_hcd 0000:00:1d.2: new USB bus registered, assigned bus number 6
[ 2.813657] uhci_hcd 0000:00:1d.2: irq 18, io base 0x00001880
[ 2.813870] usb usb6: configuration #1 chosen from 1 choice
[ 2.814008] hub 6-0:1.0: USB hub found
[ 2.814117] hub 6-0:1.0: 2 ports detected
[ 2.915707] usb usb6: New USB device found, idVendor=1d6b, idProduct=0001
[ 2.915827] usb usb6: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[ 2.915945] usb usb6: Product: UHCI Host Controller
[ 2.916050] usb usb6: Manufacturer: Linux 2.6.26-2-686 uhci_hcd
[ 2.916157] usb usb6: SerialNumber: 0000:00:1d.2
[ 2.918348] ACPI: PCI Interrupt 0000:00:1d.7[A] -> GSI 23 (level, low) -> IRQ 23
[ 2.918348] PCI: Setting latency timer of device 0000:00:1d.7 to 64
[ 2.918348] ehci_hcd 0000:00:1d.7: EHCI Host Controller
[ 2.918348] ehci_hcd 0000:00:1d.7: new USB bus registered, assigned bus number 7
[ 2.922349] ehci_hcd 0000:00:1d.7: debug port 1
[ 2.922349] PCI: cache line size of 32 is not supported by device 0000:00:1d.7
[ 2.922349] ehci_hcd 0000:00:1d.7: irq 23, io mem 0xfc404c00
[ 2.935963] ehci_hcd 0000:00:1d.7: USB 2.0 started, EHCI 1.00, driver 10 Dec 2004
[ 2.936167] usb usb7: configuration #1 chosen from 1 choice
[ 2.936272] hub 7-0:1.0: USB hub found
[ 2.936384] hub 7-0:1.0: 6 ports detected
[ 3.040534] usb usb7: New USB device found, idVendor=1d6b, idProduct=0002
[ 3.040654] usb usb7: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[ 3.040770] usb usb7: Product: EHCI Host Controller
[ 3.040873] usb usb7: Manufacturer: Linux 2.6.26-2-686 ehci_hcd
[ 3.040978] usb usb7: SerialNumber: 0000:00:1d.7
[ 3.042577] tg3.c:v3.92.1 (June 9, 2008)
[ 3.042577] ACPI: PCI Interrupt 0000:02:00.0[A] -> GSI 16 (level, low) -> IRQ 16
[ 3.042577] PCI: Setting latency timer of device 0000:02:00.0 to 64
[ 3.042577] ahci 0000:00:1f.2: version 3.0
[ 3.042577] ACPI: PCI Interrupt 0000:00:1f.2[B] -> GSI 19 (level, low) -> IRQ 19
[ 3.067331] eth0: Tigon3 [partno(BCM95787m) rev b002 PHY(5787)] (PCI Express) 10/100/1000Base-T Ethernet 00:16:d3:ee:ae:cd
[ 3.067331] eth0: RXcsums[1] LinkChgREG[0] MIirq[0] ASF[0] WireSpeed[1] TSOcap[1]
[ 3.067331] eth0: dma_rwctrl[76180000] dma_mask[64-bit]
[ 3.438319] usb 7-1: new high speed USB device using ehci_hcd and address 2
[ 3.572725] usb 7-1: configuration #1 chosen from 1 choice
[ 3.574658] usb 7-1: New USB device found, idVendor=0951, idProduct=1613
[ 3.574658] usb 7-1: New USB device strings: Mfr=1, Product=2, SerialNumber=3
[ 3.574658] usb 7-1: Product: DataTraveler 2.0
[ 3.574658] usb 7-1: Manufacturer: Kingston
[ 3.574658] usb 7-1: SerialNumber: 000FEA0560715A8A140E0020
[ 3.601311] Initializing USB Mass Storage driver...
[ 3.759313] scsi0 : SCSI emulation for USB Mass Storage devices
[ 3.761119] usb-storage: device found at 2
[ 3.761119] usb-storage: waiting for device to settle before scanning
[ 3.759313] usbcore: registered new interface driver usb-storage
[ 3.759313] USB Mass Storage support registered.
[ 4.051161] ahci 0000:00:1f.2: AHCI 0001.0100 32 slots 3 ports 3 Gbps 0x7 impl SATA mode
[ 4.051300] ahci 0000:00:1f.2: flags: 64bit ncq sntf led clo pio slum part
[ 4.051418] PCI: Setting latency timer of device 0000:00:1f.2 to 64
[ 4.053738] scsi1 : ahci
[ 4.053770] scsi2 : ahci
[ 4.053772] scsi3 : ahci
[ 4.053772] ata1: SATA max UDMA/133 abar m2048@0xfc404000 port 0xfc404100 irq 219
[ 4.053772] ata2: SATA max UDMA/133 abar m2048@0xfc404000 port 0xfc404180 irq 219
[ 4.053772] ata3: SATA max UDMA/133 abar m2048@0xfc404000 port 0xfc404200 irq 219
[ 4.190403] usb 5-2: new low speed USB device using uhci_hcd and address 2
[ 4.353981] usb 5-2: configuration #1 chosen from 1 choice
[ 4.360020] usb 5-2: New USB device found, idVendor=1267, idProduct=0201
[ 4.360020] usb 5-2: New USB device strings: Mfr=0, Product=2, SerialNumber=0
[ 4.360020] usb 5-2: Product: PS/2+USB Mouse
[ 4.377872] ata1: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
[ 4.381470] ata1.00: _GTF unexpected object type 0x1
[ 4.381580] ata1.00: ATA-7: Hitachi HTS541612J9SA00, SBDOC70P, max UDMA/100
[ 4.381580] ata1.00: 234441648 sectors, multi 16: LBA48 NCQ (depth 31/32)
[ 4.382433] ata1.00: _GTF unexpected object type 0x1
[ 4.382550] ata1.00: configured for UDMA/100
[ 4.390438] usbcore: registered new interface driver hiddev
[ 4.406962] input: PS/2+USB Mouse as /class/input/input1
[ 4.406962] input,hidraw0: USB HID v1.10 Mouse [PS/2+USB Mouse] on usb-0000:00:1d.1-2
[ 4.406962] usbcore: registered new interface driver usbhid
[ 4.406973] usbhid: v2.6:USB HID core driver
[ 4.702903] ata2: SATA link down (SStatus 0 SControl 300)
[ 5.021407] ata3: SATA link down (SStatus 0 SControl 300)
[ 5.021657] scsi 1:0:0:0: Direct-Access ATA Hitachi HTS54161 SBDO PQ: 0 ANSI: 5
[ 5.024330] ACPI: PCI Interrupt 0000:0f:06.1[A] -> GSI 22 (level, low) -> IRQ 22
[ 5.073697] ohci1394: fw-host0: OHCI-1394 1.1 (PCI): IRQ=[22] MMIO=[fc102000-fc1027ff] Max Packet=[2048] IR/IT contexts=[4/8]
[ 5.075879] Uniform Multi-Platform E-IDE driver
[ 5.075879] ide: Assuming 33MHz system bus speed for PIO modes; override with idebus=xx
[ 5.075879] sdhci: SDHCI controller found at 0000:0f:06.3 [104c:803c] (rev 0)
[ 5.075879] ACPI: PCI Interrupt 0000:0f:06.3[A] -> GSI 22 (level, low) -> IRQ 22
[ 5.076131] mmc0: SDHCI at 0xfc102800 irq 22 PIO
[ 5.076394] ICH8M: IDE controller (0x8086:0x2850 rev 0x03) at PCI slot 0000:00:1f.1
[ 5.076522] ACPI: PCI Interrupt 0000:00:1f.1[A] -> GSI 19 (level, low) -> IRQ 19
[ 5.076753] ICH8M: not 100% native mode: will probe irqs later
[ 5.079942] ide0: BM-DMA at 0x18a0-0x18a7
[ 5.079942] ide1: BM-DMA at 0x18a8-0x18af
[ 5.079942] Probing IDE interface ide0...
[ 5.104555] Driver 'sd' needs updating - please use bus_type methods
[ 5.104555] sd 1:0:0:0: [sda] 234441648 512-byte hardware sectors (120034 MB)
[ 5.104555] sd 1:0:0:0: [sda] Write Protect is off
[ 5.104555] sd 1:0:0:0: [sda] Mode Sense: 00 3a 00 00
[ 5.104555] sd 1:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[ 5.104555] sd 1:0:0:0: [sda] 234441648 512-byte hardware sectors (120034 MB)
[ 5.104555] sd 1:0:0:0: [sda] Write Protect is off
[ 5.104555] sd 1:0:0:0: [sda] Mode Sense: 00 3a 00 00
[ 5.104555] sd 1:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[ 5.104555] sda: sda1 sda2 < sda5 >
[ 5.525827] sd 1:0:0:0: [sda] Attached SCSI disk
[ 5.815681] hda: HL-DT-ST DVDRAM GSA-T20N, ATAPI CD/DVD-ROM drive
[ 6.150103] hda: host max PIO4 wanted PIO255(auto-tune) selected PIO4
[ 6.150911] hda: UDMA/33 mode selected
[ 6.151351] Probing IDE interface ide1...
[ 6.348789] ieee1394: Host added: ID:BUS[0-00:1023] GUID[000ae407396034b8]
[ 6.720757] ide0 at 0x1f0-0x1f7,0x3f6 on irq 14
[ 6.726101] ide1 at 0x170-0x177,0x376 on irq 15
[ 6.747381] hda: ATAPI 24X DVD-ROM DVD-R-RAM CD-R/RW drive, 2048kB Cache
[ 6.748072] Uniform CD-ROM driver Revision: 3.20
[ 6.967729] kjournald starting. Commit interval 5 seconds
[ 6.967729] EXT3-fs: mounted filesystem with ordered data mode.
[ 8.673927] udevd version 125 started
[ 8.784742] usb-storage: device scan complete
[ 8.788537] scsi 0:0:0:0: Direct-Access Kingston DataTraveler 2.0 1.00 PQ: 0 ANSI: 2
[ 8.789792] sd 0:0:0:0: [sdb] 15695872 512-byte hardware sectors (8036 MB)
[ 8.790345] sd 0:0:0:0: [sdb] Write Protect is off
[ 8.790345] sd 0:0:0:0: [sdb] Mode Sense: 23 00 00 00
[ 8.790345] sd 0:0:0:0: [sdb] Assuming drive cache: write through
[ 8.794395] sd 0:0:0:0: [sdb] 15695872 512-byte hardware sectors (8036 MB)
[ 8.794945] sd 0:0:0:0: [sdb] Write Protect is off
[ 8.794945] sd 0:0:0:0: [sdb] Mode Sense: 23 00 00 00
[ 8.794945] sd 0:0:0:0: [sdb] Assuming drive cache: write through
[ 8.794945] sdb: sdb1
[ 8.796040] sd 0:0:0:0: [sdb] Attached SCSI removable disk
[ 9.214792] ACPI: WMI: Mapper loaded
[ 9.554849] acer-wmi: Acer Laptop ACPI-WMI Extras version 0.1
[ 9.597635] Linux agpgart interface v0.103
[ 9.610851] input: Power Button (FF) as /class/input/input2
[ 9.658966] ACPI: Power Button (FF) [PWRF]
[ 9.659143] input: Lid Switch as /class/input/input3
[ 9.692462] ACPI: Lid Switch [LID0]
[ 9.692601] input: Sleep Button (CM) as /class/input/input4
[ 9.754967] ACPI: Sleep Button (CM) [SLPB]
[ 10.044247] ACPI: device:05 is registered as cooling_device2
[ 10.044431] input: Video Bus as /class/input/input5
[ 10.107910] ACPI: Video Device [VGA] (multi-head: yes rom: no post: no)
[ 10.109824] input: Video Bus as /class/input/input6
[ 10.169901] ACPI: Video Device [GFX0] (multi-head: yes rom: no post: no)
[ 10.178405] ACPI: AC Adapter [ADP1] (on-line)
[ 10.381203] ACPI: Battery Slot [BAT0] (battery present)
[ 10.424480] iwl3945: Intel(R) PRO/Wireless 3945ABG/BG Network Connection driver for Linux, 1.2.26ks
[ 10.424604] iwl3945: Copyright(c) 2003-2008 Intel Corporation
[ 10.424848] ACPI: PCI Interrupt 0000:04:00.0[A] -> GSI 17 (level, low) -> IRQ 17
[ 10.425077] PCI: Setting latency timer of device 0000:04:00.0 to 64
[ 10.425099] iwl3945: Detected Intel Wireless WiFi Link 3945ABG
[ 10.544189] iwl3945: Tunable channels: 13 802.11bg, 23 802.11a channels
[ 10.544189] phy0: Selected rate control algorithm 'iwl-3945-rs'
[ 10.770773] input: PC Speaker as /class/input/input7
[ 10.821625] ACPI: PCI interrupt for device 0000:04:00.0 disabled
[ 10.821625] ACPI: PCI Interrupt 0000:00:1f.3[C] -> GSI 19 (level, low) -> IRQ 19
[ 10.821625] Yenta: CardBus bridge found at 0000:0f:06.0 [1025:011f]
[ 10.821625] PCI: Bus 16, cardbus bridge: 0000:0f:06.0
[ 10.821660] IO window: 0x00006000-0x000060ff
[ 10.821774] IO window: 0x00006400-0x000064ff
[ 10.821888] PREFETCH window: 0x50400000-0x507fffff
[ 10.822004] MEM window: 0x54000000-0x57ffffff
[ 10.822124] Yenta: Using CSCINT to route CSC interrupts to PCI
[ 10.822233] Yenta: Routing CardBus interrupts to PCI
[ 10.822347] Yenta TI: socket 0000:0f:06.0, mfunc 0x01aa1b22, devctl 0x64
[ 10.968380] NET: Registered protocol family 23
[ 11.062410] Yenta: ISA IRQ mask 0x0cf8, PCI irq 22
[ 11.065502] Socket status: 30000006
[ 11.065502] Yenta: Raising subordinate bus# of parent bus (#0f) from #10 to #13
[ 11.065502] pcmcia: parent PCI bridge I/O window: 0x6000 - 0x6fff
[ 11.065502] cs: IO port probe 0x6000-0x6fff: clean.
[ 11.065502] pcmcia: parent PCI bridge Memory window: 0xfc100000 - 0xfc1fffff
[ 11.070397] ACPI: PCI Interrupt 0000:0f:06.2[A] -> GSI 22 (level, low) -> IRQ 22
[ 11.081506] ACPI: PCI Interrupt 0000:00:1b.0[A] -> GSI 22 (level, low) -> IRQ 22
[ 11.081506] PCI: Setting latency timer of device 0000:00:1b.0 to 64
[ 11.121508] hda_codec: Unknown model for ALC268, trying auto-probe from BIOS...
[ 11.412411] Synaptics Touchpad, model: 1, fw: 6.3, id: 0x12a0b1, caps: 0xa04713/0x204000
[ 11.467264] input: SynPS/2 Synaptics TouchPad as /class/input/input8
[ 11.532689] nsc-ircc 00:0a: activated
[ 11.532850] nsc-ircc, chip->init
[ 11.532850] nsc-ircc, Found chip at base=0x02e
[ 11.532850] nsc-ircc, driver loaded (Dag Brattli)
[ 11.532850] IrDA: Registered device irda0
[ 11.532926] nsc-ircc, Found dongle: Supports SIR Mode only
[ 11.533092] nsc-ircc, chip->init
[ 11.533212] nsc-ircc, Found chip at base=0x02e
[ 11.533364] nsc-ircc, driver loaded (Dag Brattli)
[ 11.533477] nsc_ircc_open(), can't get iobase of 0x2f8
[ 11.550839] cs: IO port probe 0x100-0x3af: clean.
[ 11.550839] cs: IO port probe 0x3e0-0x4ff: excluding 0x4d0-0x4d7
[ 11.552243] cs: IO port probe 0x820-0x8ff: clean.
[ 11.554835] cs: IO port probe 0xc00-0xcf7: clean.
[ 11.556106] cs: IO port probe 0xa00-0xaff: clean.
[ 12.788736] EXT3 FS on sda1, internal journal
[ 13.058777] loop: module loaded
[ 13.586939] fuse init (API version 7.9)
[ 13.805384] kjournald starting. Commit interval 5 seconds
[ 13.805542] EXT3 FS on sda5, internal journal
[ 13.805542] EXT3-fs: mounted filesystem with ordered data mode.
[ 15.079578] ACPI: PCI Interrupt 0000:04:00.0[A] -> GSI 17 (level, low) -> IRQ 17
[ 15.079578] PM: Writing back config space on device 0000:04:00.0 at offset 1 (was 100102, writing 100106)
[ 15.079578] firmware: requesting iwlwifi-3945-1.ucode
[ 15.160751] Registered led device: iwl-phy0:radio
[ 15.160751] Registered led device: iwl-phy0:assoc
[ 15.160751] Registered led device: iwl-phy0:RX
[ 15.160751] Registered led device: iwl-phy0:TX
[ 27.557087] NET: Registered protocol family 10
[ 27.557383] lo: Disabled Privacy Extensions
[ 27.559374] ADDRCONF(NETDEV_UP): wlan0: link is not ready
[ 27.896916] lp: driver loaded but no devices found
[ 27.939285] ppdev: user-space parallel port driver
[ 30.713400] vboxdrv: Trying to deactivate the NMI watchdog permanently...
[ 30.713400] vboxdrv: Successfully done.
[ 30.713400] vboxdrv: Found 2 processor cores.
[ 30.713400] vboxdrv: fAsync=0 u64DiffCores=5544.
[ 30.713447] vboxdrv: TSC mode is 'synchronous', kernel timer mode is 'normal'.
[ 30.713554] vboxdrv: Successfully loaded version 1.6.6_OSE (interface 0x00080000).
[ 31.069155] warning: `ntpd' uses 32-bit capabilities (legacy support in use)
[ 32.726813] Bluetooth: Core ver 2.11
[ 32.726813] NET: Registered protocol family 31
[ 32.726813] Bluetooth: HCI device and connection manager initialized
[ 32.726813] Bluetooth: HCI socket layer initialized
[ 32.759132] Bluetooth: L2CAP ver 2.9
[ 32.759219] Bluetooth: L2CAP socket layer initialized
[ 32.834861] Bluetooth: RFCOMM socket layer initialized
[ 32.834861] Bluetooth: RFCOMM TTY layer initialized
[ 32.834861] Bluetooth: RFCOMM ver 1.8
[ 33.065741] ADDRCONF(NETDEV_UP): eth0: link is not ready
[ 60.013746] CPU0 attaching NULL sched-domain.
[ 60.013754] CPU1 attaching NULL sched-domain.
[ 60.017022] CPU0 attaching sched-domain:
[ 60.017028] domain 0: span 0-1
[ 60.017032] groups: 0 1
[ 60.017040] CPU1 attaching sched-domain:
[ 60.017044] domain 0: span 0-1
[ 60.017048] groups: 1 0
[ 232.314062] usb 7-5: new high speed USB device using ehci_hcd and address 4
[ 232.449651] usb 7-5: configuration #1 chosen from 1 choice
[ 232.452148] scsi4 : SCSI emulation for USB Mass Storage devices
[ 232.452266] usb-storage: device found at 4
[ 232.452270] usb-storage: waiting for device to settle before scanning
[ 232.452568] usb 7-5: New USB device found, idVendor=152d, idProduct=2329
[ 232.452568] usb 7-5: New USB device strings: Mfr=1, Product=2, SerialNumber=5
[ 232.452568] usb 7-5: Product: USB to ATA/ATAPI Bridge
[ 232.452568] usb 7-5: Manufacturer: JMicron
[ 232.452568] usb 7-5: SerialNumber: 5174FFFFFFFF
[ 237.451103] usb-storage: device scan complete
[ 237.456217] scsi 4:0:0:0: Direct-Access ST950042 0AS PQ: 0 ANSI: 2 CCS
[ 237.459383] sd 4:0:0:0: [sdc] 976773168 512-byte hardware sectors (500108 MB)
[ 237.460817] sd 4:0:0:0: [sdc] Write Protect is off
[ 237.460817] sd 4:0:0:0: [sdc] Mode Sense: 34 00 00 00
[ 237.460817] sd 4:0:0:0: [sdc] Assuming drive cache: write through
[ 237.461639] sd 4:0:0:0: [sdc] 976773168 512-byte hardware sectors (500108 MB)
[ 237.462312] sd 4:0:0:0: [sdc] Write Protect is off
[ 237.462312] sd 4:0:0:0: [sdc] Mode Sense: 34 00 00 00
[ 237.462312] sd 4:0:0:0: [sdc] Assuming drive cache: write through
[ 237.462312] sdc: sdc1 < sdc5 >
[ 237.537055] sd 4:0:0:0: [sdc] Attached SCSI disk